Hypercom T7Plus Installation Guide
Contents
1. Cleaning the T7Plus T7Plus Use the following procedure to clean the casing and the printer mechanism of the T7 Plus TERMINAL A WARNING DO NOT use undiluted ammonia or abrasive cleaners INSTALLATION Apply denatured alcohol or a Windex type product to a clean soft non abrasive low lint cloth Carefully wipe the entire terminal GUIDE Fa As needed use anti static compressed air to clean in and around the printer mechanism ee Supply Information If you are unable to purchase items such as paper through your bank or processor contact Merchant Supplies at 800 522 8710 Compliance This equipment is compliant with the following e FCC Part 15 ICES 003 e EN60950 e FCC Part 68 CS 03 e CISPR 22 e CTR21 e AS NZS 3260 e EN55022 e AS NZS 3548 e EN55024 Adding Value to Innovation World Headquarters 2851 West Kathleen Road Phoenix AZ 85053 602 504 5000 877 HYPERCOM within USA e Fax 602 504 5166 e mail info hypercom com web www hypercom com Hypercom Corporation 2002 Printed in the United States of America 940365 002 Rev D 10 02 T7Plus Terminal The Hypercom epic ePOS infocommerce T7 Plus combines the flexibility of a full featured smart card ready HyperSmart integrated POS terminal with the infrastructure to quickly and cost effectively integrate new applications This combination makes the T7Plus the simplest and most innovative POS solution avail2. 2 Slide the card all the way though the long credit card slot on the right side of the terminal starting on either end in one smooth motion See Figure 6 Figure 6 3 Follow standard operating procedures to complete the transaction See the T7Plus HyperWare Retail and Restaurant Software Manual or contact your bank or processor for more information Smart Card Slot i Using a Smart Card Optional Use the following procedure to insert a Smart Card Credit Card Slot 1 When holding the smart card make sure the metallic contact is facing upward and toward the body of the terminal 2 Insert the card into the Smart Card slot on the right side of the T7Plus See Figure 6 Remove the Smart Card when the terminal screen instructs you to do so
3. See Figure 2 The use of a different cable may result in improper operation Note Ensure that the telephone line cable latches firmly into the jacks on the T7Plus terminal and wall receptacle Note If connection to an extension telephone is needed install a Hypercom Line Splitter into the terminal port labeled LINE Install the line from the extension phone into the PHONE port on the Splitter Install the line from the wall receptacle into the LINE port See Figure 3 The terminal disconnects the PHONE port when a transaction is being processed Phone Port Line Port Figure 4 Setup Procedures Use the following procedures to set up your T7Plus for operation Loading Paper Use the following procedure to load paper into the T7Plus terminal Note Use only thermal roll paper 1 Squeeze the paper cover tabs and lift open the paper cover See Figure 4 2 Place the paper roll into the holder so the paper feeds from under the roll Pull the end of the paper roll over the printer See Figure 5 Figure 5 j 3 While holding the end of the paper roll close the paper cover You will hear the paper cover click when properly latched See Figure 5 Paper Roll 4 Tear off the excess paper Using a Credit Card A credit card can be swiped bi directionally either toward or away from you 1 When holding the card make sure the stripe is facing away from the body of the terminal toward your right and down
4. able today Note Features on your model of T7Plus may vary from those shown in this installation guide Installation Procedures Note The following equipment warnings are for your safety and that of your equipment Do not use an ungrounded adapter power adapter power extender cable or AC outlet Do not disassemble the AC adapter Only qualified technicians may service the adapter The AC adapter is intended for indoor use only do not expose to rain or snow Do not immerse the AC adapter or the terminal in fluid Ensure that the telphone line is disconnected when the unit is unplugged from the AC power outlet Powering Up the Terminal Use the following procedure to power up the T7Plus 1 Connect the 24 VDC power cable from the AC adapter to the three pin terminal power socket labeled PWR on the back panel of the T7Plus See Figure 1 2 Plug the adapter into a grounded AC power outlet When the power is properly connected the terminal beeps twice then performs a self test routine Power Socket RS 232 Port Connecting the Telephone Line Figure 2 Use the following procedure to connect a telephone line to the T7 Plus 1 Insert the telephone cable shipped with the T7Plus terminal into a dedicated analog telephone outlet AN WARNING DO NOT insert the telephone line into the PIN pad port A 2 Connect the other end of the telephone cable into the port labeled LINE on the back panel of the T7Plus terminal
Download Pdf Manuals
Related Search