PSR04 Smart Color Button
Contents
1. COMMAND_CLASS_CENTRAL_SCENE_V1 COMMAND_CLASS_VERSION_V2 COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2 COMMAND_CLASS_DEVICE_RESET_LOCALLY COMMAND_CLASS_ASSOCIATION_V2 COMMAND_CLASS_WAKE_UP_V2 COMMAND_CLASS_ASSOCIATION_GRP_INFO COMMAND_CLASS_POWERLEVEL COMMAND_CLASS_MULTI_CMD COMMAND_CLASS_SECURITY COMMAND_CLASS_FIRMWARE_UPDATE_MD_V2 COMMAND_CLASS_CONFIGURATION Security Network The device support the security function When the device included with a security controller the device will auto switch to the security mode In the security mode the follow commands need using Security CC wrapped to communicate otherwise it will not response COMMAND_CLASS_ BATTERY COMMAND_CLASS_ASSOCIATION_V2 COMMAND_CLASS CONFIGURATION COMMAND_CLASS_WAKE_UP_V2 COMMAND_CLASS_CENTRAL_SCENE Troubleshooting Specification 1 Battery is 1 Charging the battery by Voltage i i running out of Micro USB oF VDV Micro USB Port power 2 Pointing the arrowhead Voltage Wrong function to area B and press the Range Minimum 40 m in door 100m outdoor line of mode touch button sight If the device still can Operating 10 C 40 C work don t open up the Temperature Switch and send it for Frequency Range PSR04 1 868 40MHz 869 85MHz EU repair PSR04 2 908 40MHz 916 00MHz USA Canada Can not adjust the 1 The device may 1 Check if the device is PSRO4 3 922 5MHz 923 9MHz 926 3MHz percentage of not be placed pl2. 1 5 seconds The red LED will light up for 1 second if succeed 2 Exclude Pointing the arrowhead to area A first Pressing the button three times within 1 5 seconds 3 Reset to default Pointing the arrowhead to area A first Pressing button four times within 2 seconds and hold at fourth The red LED will light for 3 seconds release the button within 2 seconds while the LED goes out The LED will flash for 1 second if reset succeed or LED will flash once Notice Including a node ID allocated by Z Wave Controller means Add or Inclusion Excluding a node ID allocated by Z Wave Controller means Remove or Exclusion Function This device can control dimmers in group 2 using three ways Dimmer Timer and On Off Switch Point the arrowhead to area A shown in Fig 1 and Fig 2 then hold the button release after the red LED go out One beep means entering Timer mode or two beeps means entering Dimmer mode The device can switch to On Off Switch mode automatically when fitting horizontal gt 100 Dimmer 90 ON OFF Ti mer Include Exclude Figure l This device is able to set dimmer level by rotating to different angle When the status is Off surround LED will not work except in area A shown in Fig 1 Rotate the device to area B C D shown in Fig 1 then touch the button can set the status to On After a short beep the surround LED will change gradually from blue
3. to red in area D It will send Basic set command automatically 1 second after rotating stop To turn Off the device in group 2 you can rotate PSR04 to area C or touch the button again Timer 1 15 Minutes 1 Minute 15 Minutes Figure 2 This mode can time the length of turning Off the light The length is up to 15 minutes When counting down starts surround LED will flash and buzzer will sound according to the remaining time Rotating to area C can cancel counting down directly Note Buzzer in timer mode can be disabled by setting Configuration NO 25 bit 1 to 1 Timer left Flash color Buzzer 10 15 minutes Cyan 10 seconds 5 10 minutes Green 10 seconds 3 5 minutes Yellow 10 seconds 1 3 minutes Orange 10 seconds 30 60 seconds Pink 10 seconds 10 30 seconds Pink 10 seconds Pink 1 second Time up White 1 second 1 beep 10 seconds 1 5 seconds 1 beep 1 second 4 beeps 1 second On Off Switch This device is able to work as On Off switch by sending Basic set according to configuration NO 1 and NO 2 when fitting horizontal Association This device supports 2 association groups which every group has eight node support To build disable association between devices 1 Have the Z Wave controller entered association mode 2 Rotate PSR04 to area A then press the button three times within 1 5 seconds Group 1 is for receiving the report messag
4. PSRO4 Smart Color Button Full Color LED 1 O Red Light LED Full Color LED 2 This device is a multiple functions button switch It is able to switch the appliances on off or adjust the percentage of dimmer It can also work as a timer The well designed wall bracket and magnetic back let the switch can be fixed on the wall This product can be included and operated in any Z Wave network with other Z Wave certified devices from other manufacturers and or other applications Note Please provide a 5 DVC voltage through Micro USB Port to wake the device up before the first using The rotation function and timer functions work only when the device is fitted upright or stick on the wall or the device will only work as on off switch when fitted horizontal Z Wave Network Setting Up In the first time add the device into the Z Wave network Make sure the primary controller is in the add mode And then power on the device through micro USB The device will auto start the NWI Network Wide Inclusion Red LED will flash every second and continue 30 seconds And it should be included in 5 seconds Red LED will light ON one second Rotating to area A shown in Fig 1 and touch 3 times can abort NWI mode There is a touch button on the front side The button carries out manual inclusion exclusion and reset to default 1 Include Pointing the arrowhead to area A first shown in Fig 1 Pressing the button three times within
5. aced upright Taiwan JP dimmer upright 2 Rotating to the Specifications are subject to change and improvement without The device is in percentage you want notice off state then press touch button Or pointing the F arrowhead to area B and X press the touch button Qwave C FCC ID RHHPSRO4 to turn the lamp on then m adjust the percentage The device can not 1 The device may 1 Exclude the device then Disposal in a Z Wave include again This marking indicates that this product should not be network Pointing the arrowhead Nee disposed with other household wastes throughout the EU 2 The arrowhead to area A then include AC To prevent possible harm to the environment or human points to wrong again health from uncontrolled waste disposal recycle it area responsibly to promote the sustainable reuse of material Button no response 1 The button will Wait for the LED go out resources To return your used device please use the no response and try again return and collection systems or contact the retailer where when LED is the product was purchased They can take this product for flashing environmental safe recycling Company of License Holder Philio Technology Corporation Address of License Holder 8F No 653 2 Zhongzheng Rd Xinzhuang Dist New Taipei City 24257 Taiwan R O C FCC Interference Statement This equipment has been tested and found to comply with the lim its for a Class B digital device pursua
6. e like the battery level Group 2 is for light control the device will send Basic Set command to this group Timing Report The device supports the timing unsolicited report of the status e Battery level report Every 6 hours report once in default It could be changed by setting the configuration NO 10 e Low battery report When the battery level is too low every 30 minutes will report once Z Wave Notification After the device adding to the network it will wake up once per day in default When it wake up it will broadcast the Wake Up Notifica tion message to the network and wake up 10 seconds for receive the setting commands The wake up interval minimum setting is 30 minutes and maximum setting is 120 hours And the interval step is 30 minutes If the user want to wake up the device immediately please rotate to area A and pressing the touch button once The de vice will wake up for 10 seconds every single time Configuration The configuration mark with star means after the remove the setting still keep don t reset to factory default Unless the user execute the RESET procedure NO Name Size Def Valid Description Byte Values Control the value represented by the left side in area D 1 Basic Set 1 0x00 Ox00 0x63 E g Setting this configuration OFF level to OxOF means range of Command Basic Set value start from Ox0F Control the value represented by the right side in area D 2 Ba
7. nt to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the in structions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or tele vision reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one of the follow ing measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including in terference that may cause undesired operation FCC Caution Any changes or modifications not expressly approved by the party responsible for compliance could void the user s author ity to operate this equipment This transmitter must not be co located or
8. operating in conjunction with any other antenna or transmitter
9. sic Set 1 0x63 O0x00 0x63 E g Setting this configuration ON level to Ox1E means range of Command Basic Set value start from Ox1E Auto The interval time for auto re Report porting the Battery level 0 10 Battery 12 1 127 means turn off auto report Time battery The default value is 12 Bit 0 Dimmer setting method 0 Auto send Command Ba sic Set after rotating Customer 1 Send Command Basic Set 25 Function 0x00 0Ox00 0x03 by touching key after rotating Bit 1 Disable buzzer in timer mode 0 Enable 1 Disable Disable Send Central Scene Holding Scene 0x00 0x00 0x01 when the button is held 26 Holding 0x00 Enable report 0x01 Disable Installation 1 Fix the bracket on the wall 2 There s a magnet on the backside of this device It can stick to the bracket Notice Do not install the bracket on unstable wall this may cause miscarriage to control lights Firmware update over the air OTA This device supports the Z Wave firmware update via OTA Let the controller into the firmware update mode and rotate to area A then touch the button once to start update After finish the firmware download the red LED will start to flash every 0 5 sec ond Please don t remove the battery before the LED stop flashing Notice recommend using OTA when the device is charging Supported Z Wave Command Classes COMMAND_CLASS_ZWAVEPLUS_INFO_V2 COMMAND_CLASS_BATTERY
Download Pdf Manuals
Related Search