USER`S MANUAL
Contents
1. C ENTER 20 To exit Program Mode DELETING USER CODES At Step 3 enter MEMORY E instead of a new code ddd Q Press CENTER 220 Q Press E The existing code has now been erased The existing code has now been erased EXAMPLES The panel must be in program mode Program light ON To program User Code 1 to be 1234 P11E 1234 E 1234 E To program User Code 2 to be 5678 and an ARM ONLY code P12E ARM E 5678 E 5678 E When an Arm Only code is displayed the ARM light or icon is displayed before the digits of the code To delete User Code 2 P12E MEMORY E USER CODE PROGRAMMING RULES All codes can be 3 4 5 or 6 digits long e Codes beginning with 0 zero can be programmed but they will not operate the panel This is an alternative method for disabling user codes however the MEMORY E function is recommended for deleting user codes Codes are rejected if already used Some codes that are similar to existing codes may also be rejected The Master Code User Code 1 cannot be an ARM ONLY code The Master Code must always be programmed all other codes are optional For a list of programming option numbers see the Programming Options Table on page 19 EJ NESS D8 V4 5 CONTROL PANEL USER MANUAL PROGRAMMING PROGRAMMING TIMERS LED KEYPAD LCD KEYPAD Press proc Master Code d Press P Master Code e Enters Program2. 10 Resetting Alarms 10 Monitor Mode sseem 11 Keypad Panic ite reete 12 Keypad Duress 12 Keypad Fire Alarm 13 Keypad Medical Alarm 13 Excluding Zones 5 rentre 14 View Memory euet eed ute 15 RADIO KEY OPERATION 16 MONITORING OPERATION 17 PROGRAMMING 2 ccccecceceeseeseeeeeeeeeseeeeeeeeeneeateaes 18 Programming Options Table 19 User Code 20 Entry Exit Timer programming 21 Telephone Number programming 21 Remote Operation by Telephone 22 23 Ness Accessories 24 25 Troubleshooting 26 Installation 27 OPERATION SUMMARY 28 NESS D8 FEATURES 8 Fully programmable zones Any combination of hardwire or radio zones Full radio supervision Contact ID Dialler Format Ultra Modern and Impact resistant Housing Ness Audible Dialler Format Follow Me Audible Dialler Option Separa
3. m 2 xz 5 gt P28E EXIT DELAY TIME Seconds rot EEZFGRGiZ rae 26 8 i amp amp T 2 x 2 Set b Rae P29E SIREN RESET TIME Minutes am ad GP uio dH d du Oo ag e N eo 7 N wo N st 1 i iD M a ZONES DEVICE fis DESCRIPTION Entrance bedroomt etc 1 2 3 4 5 6 7 8 AREA 1 2 RADIO KEY CODE OPTION No CODE HOLDER CODE Y N User Code 1 P11E Keypad Code only User Code 2 P12E User Code 3 P13E User Code 4 P14E User Code 5 P15E User Code 6 P16E User Code 7 P17E User Code 8 P18E User Code 9 P19E User Code 10 P20E User Code 11 P21E User Code 12 P22E User Code 13 P23E User Code 14 P24E User Code 15 P25E 2001 Ness Security Products NESS D8 V4 5 CONTROL PANEL USER MANUAL Ea OPERATION SUMMARY OPERATION ARM The panel must be in a Disarmed state first DISARM To Disarm and or reset alarms MONITOR MODE The panel must be in a Disarmed state first KEYPAD DURESS Keypad Duress is factory defaulted for silent reporting EXCLUDING ZONES EXCLUDE ENTER can only be used when the panel is disarmed EXCLUDE CODE ENTER can be used when the panel is armed or disarmed VIEW MEMORY View Memory can only be used when the panel is disarmed LED KEYPAD Arming Shortcut m
4. NESS RADIO PIR Ness Radio PIR Passive Infrared and Ness R12 Radio PIR for wireless motion detection be used in combination with Ness Ness R12 Radio hardwired detectors in areas where it is not possible to install wires Includes long life lithium battery The Ness Radio Pet Aware model detects humans but is immune to household pets Allows you to protect your home with your pets inside SR wt Ness Radio PIR amp Ness PET AWARE Pet Aware Radio PIR NESS RADIO SMOKE DETECTOR Radio Smoke Detector using lonisation smoke detection technology With on board sounder A single battery powers the smoke detector and the transmitter Includes 9V lithium battery NESS D8 V4 5 CONTROL PANEL USER MANUAL EJ TROUBLESHOOTING SYMPTOM Zone light on or long beeps when Arming POSSIBLE CAUSE One or more Zone Detection Devices e g PIR Reed Switch may be Unsealed REMEDY Close door or window find the cause of movement 10 beeps from keypad MAINS light flashing BATTERY light flashing The mains power may be off Or the panel s backup battery may be low Radio Device battery may be low Make sure the plug pack is plugged in and the power point is turned on Call your installer 1 long beep from keypad Invalid keypad entry Press E button and try again 2 second siren at the end of Exit Delay time A zone was Unsealed at the end of Exit
5. New alarms in memory O EXCLUDE EXCLUDE orma Zones are excluded O TAMPER TAMPER orma Tamper alarm 2 M Indicates that a Radio Key or O RADIO RADIO ormal Receiving radio signal wu has a Phone line faul LINE 4 Dialler is on line failure PROGRAM PROGRAM ormai User Program Mode Installer Program Mode Ready to Arm Not ready to Arm MEMORY MODE EVENTS INDICATED BY KEYPAD LIGHTS LIGHT Zone lights 1 8 no lights ARMED RADIO EXCLUDE RADIO BATTERY ZONE RADIO BATTERY ARM RADIO TAMPER ZONE MEMORY EVENT nu Zone alarm s Panel Disarmed Panel Armed or Area 1 Armed I Area 2 Armed Panic alarm Telephone line fail Radio Key Panic alarm Radio Device battery low Device number is indicated by light 1 8 Radio Key battery low Radio Key number is NOT indicated Radio Device tamper alarm Device number indicated by light 1 8 m Mains power failure gu Low Battery Tamper alarm Siren cover panel etc LCD Keypad RADIO MONITOR ZONE Radio Supervision fail Device number is indicated by light 1 8 LED Keypad RADIO ZONE Radio Supervision fail Device number is indicated by light 1 8 NESS D8 V4 5 CONTROL PANEL USER MANUAL Ea OPERATION This section describes the operation of a typical control panel
6. 5 9 Finished hang up NOTES f the D8 does not receive commands for periods longer than 10 seconds it will assume that the call is finished and it will hang up f an alarm occurs which requires the D8 to dial out while attempting remote control the D8 will treat the alarm as a priority give a constant tone as a warning and then hang up When all remote control commands are finished press x to force the D8 to hang up NESS D8 V4 5 CONTROL PANEL USER MANUAL EJ NESS ACCESSORIES MABE AUSTRALIA aa d J 100 021 100 226 100 210 100 048 Quantum Quantum Quantum Quantum 360 Plus Dual MOTION DETECTORS Ness manufactures a range of high quality and efficient motion detectors including passive infra red detectors dual technology microwave and infra red devices as well as ceiling mounted 360 detectors All Ness detectors are designed using the most modern technology and techniques that ensure superior reliability and performance QUANTUM 15m passive infra red detector with selectable pulse count suitable for domestic and commercial installations PetAware model available QUANTUM PLUS 15m passive infra red detector with selectable pulse count temperature compensation and downward looking creep zones QUANTUM DUAL 15m combination microwave and passive infra red detector This combination of detection technologies virtually eliminates th
7. detector becomes faulty and cannot be Zone Exclude IS not permanent Excluded Sealed when arming the panel then its zone zones are automatically INCLUDED next time may be Excluded so that it does not generate the panel is Disarmed alarms Zones can be manually included by the same When zones have been Excluded the method as Excluding Simply use the EXCLUDE light flashes continuously while the ZONE NUMBER E sequence to turn OFF the panel is Disarmed and also when Armed zone lights to be Included Zones can be excluded while the panel is either Disarmed or Armed See notes below NOTES EXCLUDE E works only when the panel is Disarmed EXCLUDE User Code E works in any state EXCLUDE User Code E can only exclude the zones in the Area assigned to that code E NESS D8 V4 5 CONTROL PANEL USER MANUAL OPERATION LED KEYPAD LCD KEYPAD ddd Press ENTER or User Code CHRD The Memory light will turn on Q Press The most recent event will be displayed Press The next most recent event will be displayed Press so on up 30 events Press to exit Memory mode Press E M or User Code The M MEMORY icon will turn on Press The most recent event will be displayed Press The next most recent event will be displayed Press MEMORY
8. C buttons I PANIC MEMORY ARM button I ARM C12 C22 CG MONITOR button MONITOR button Qo EXCLUDE button EXCLUDE button C7 9 I roar C ENTER PROGRAM button PROGRAM button ENTER button L ENTER button MEMORY button Protective flap not shown Protective flap not shown The Not Ready light is on when the panel is not ready to Arm ie a zone is unsealed there may still be movement in the premises or a door or window left open KEYPAD BEEPER SOUNDS LED keypad and LCD keypad Each key press J Valid command dJ 3 beeps Error 4 1 1 long beep Mains Power is off 10 Keypad beeper sounds for oi 4 116 10 beeps LED or LCD keypad Panel Battery is low EN NESS D8 V4 5 CONTROL PANEL USER MANUAL 135mm KEYPAD INDICATORS KEYPAD LIGHTS IN NORMAL OPERATING MODE N 1 LED KEYPAD LCD KEYPAD FLASHING ZONES 1 8 Zone is sealed Zone is unsealed Zone alarm VA Zone is unsealed or Power fault System is Armed READY arom Monitor Mode ARMED Fl ARMED Disarmed Armed AREA 1 LED Keypad only ARM2 Gi ARM2 Disarmed Armed AREA 2 Geer Disarmed Monitor Mode MAINS oF ormal Mains Power is off The panel s backup EMO BATTERY orma battery is low MEMORY ormal Memory Mode selected
9. Delay time Disarm the panel and check all zones Strobe light is flashing There has been an alarm Reset the alarm by Disarming the panel and check the Alarm Memory Siren sounds while the panel is Disarmed A 24 hour zone has been triggered E g Siren Tamper Box Tamper Panic Button Reset the alarm by Disarming the panel and call your installer EXCLUDE light is flashing A zone s has been Excluded TAMPER light flashing The 24 hour Tamper input has triggered Call your installer ALARM MEMORY light is flashing There are alarms in memory To clear the ALARM MEMORY light view the Alarm memory otherwise the light will clear next time you Arm the panel Cannot enter Program Mode The panel is Armed Only the Master Code can enter Program Mode Disarm the panel before attempting to enter Program Mode Try again using the Master Code EJ NESS D8 V4 5 CONTROL PANEL USER MANUAL INSTALLATION RECORD INSTALLATION RECORD Date purchased Date installed Installation Company D 8 Telephone DIALER SECUnmY AAT NESS D8 Monitoring Company ALARM CONTROL PANEL Telephone ES ZONE ASSIGNMENT cg P26E ENTRY DELAY TIME 1 Seconds 5 E25 EE P27E ENTRY DELAY TIME 2 Seconds
10. Disarm only that Area User Codes assigned to both Areas will operate both Areas simultaneously COMMON AREA ZONES Zones assigned to both Areas are Armed only when Area1 and Area2 are both Armed This allows the Common Area zone s to be shared by both Areas For example Office A and Office B operate as separate areas but the entrance foyer used by both offices is assigned to both areas meaning it will automatically Arm when both Areas have Armed The Common Area then automatically disarms when either Area1 or Area2 Disarms OPERATION Arming and Disarming is carried out as normal from a single keypad or separate keypads installed in both areas or by Radio Key Area operation only applies to zones when they are in the Armed state This means that Day 24hr and Monitor zones are independent of the area operations Note Area partitioning is in addition to Monitor Mode Any zone may be allocated to any area EN NESS D8 V4 5 CONTROL PANEL USER MANUAL OPERATION LED KEYPAD LCD KEYPAD The Ready light should be on Press x or User Code CCHR The e Armed light will turn on Leave the premises within the Exit Delay Time 3 beeps will sound at the end of Exit Delay Time Q The Not Ready light should be off Press Or User Code as The fa ARMED icon will turn on e Leave the premises within the E
11. INEZSZ D 8 ALARM CONTROL PANEL AND DIALLER MADE AUSTRALIA pM y USER S MANUAL Ness D8 control panel User s manual A 15 00 INC GST Revision 4 5 Australia s largest designer and manufacturer of high quality security products MADEX AUSTRALIA Le v N55 NESS SECURITY PRODUCTS Australian Communications Authority TELECOMMUNICATIONS COMPLIANCE Quality Endorsed Company 1809001 LIC No QEC2074 Ness Security Products Pty Ltd iiec WWW NESS COM AU HEAD OFFICE Ness Security Products Pty Ltd ABN 28 069 984 372 4 167 Prospect Hwy Seven Hills NSW 2147 Australia Ph 61 2 8825 9222 Fax 61 2 9674 2520 ness ness com au SYDNEY 02 8825 9222 MELBOURNE 03 9878 1022 BRISBANE 07 3343 7744 ADELAIDE Aquavia Controls 08 8277 7255 PERTH 08 9328 2511 NEW ZEALAND NFS NZ 64 9 573 0401 NESS D8 USER MANUAL Revision 4 5 June 2002 Document Part Number 890 264 For products 100 191 D8 LED Control Panel V4 5 100 688 D8 LCD Control Panel V4 5 2002 Ness Security Products Pty Ltd ABN 28 069 984 372 D8 V4 User rev4 5 pmo140602 Specifications may change without notice CONTENTS ona cn ee ed 4 InttOdUCtlOn 2c oet Hee 5 Keypad iri pepe RE ende 6 Visual Indicators iior 7 KEYPAD 8 Se tied Ede et OE Ie eet 9 Disarring re
12. Mode The PROGRAM light will be on Enters Program Mode The PROGRAM light will be on T JJ MEI Press Proc Option No C ENTER Press Option No E The existing time will be displayed The existing time will be displayed ddd ddd Press NEW TIME ENTER Press NEW TIME The new time will be displayed The new time will be displayed ddd ddd Press Roera C ENTER O Press E To exit Program Mode To exit Program Mode EXAMPLES The panel must be in program mode Program light ON To program the Entry Delay Time to be 15 seconds P26E 15 E To program the Exit Delay Time to be 40 seconds P28E 40 E For a list of programming option numbers see the Programming Options Table on page 19 PROGRAMMING THE FOLLOW ME TELEPHONE NUMBER LED KEYPAD LCD KEYPAD 2 Q Press rocram Master Code ENTER Press Master Code E Enters Program Mode The PROGRAM light will be on Enters Program Mode The PROGRAM light will be on ddd ddd Press proe 0 CO C ENTER Press P 0 C0 E The existing telephone number if any will be displayed The existing telephone number if any will be displayed ddd ddd e Press NEW TELEPHONE NUMBER ENTER Press NEW TELEPHONE NUMBER E The new telephone number will be displayed The new telephone number will be displayed ddd 441 Pr
13. S D8 V4 5 CONTROL PANEL USER MANUAL EN OPERATION LED KEYPAD LCD KEYPAD Q Enter the premises through a delay zone Press User Code JJJ Q The e Armed light will turn off Enter the premises through a delay zone Press User Code The 5 armen icon will turn off When you enter the protected premises through a delay zone the keypad responds with regular beeps as a reminder to Disarm You then have your programmed entry delay time to Disarm the panel by entering one of your user codes If the panel is not Disarmed by the end of the entry delay time an alarm will occur By using the optional radio keys you may Disarm your system from within your premises or from outside your entrance door There is also the option to Chirp the outside siren three times and to flash the strobe light for two RESETTING ALARMS Your panel can be reset and the alarm silenced by the same key sequence as Disarming the panel If you arrive at your premises and find the strobe light flashing if installed reset the panel as above To check the cause of the alarm you can view the alarms in memory by entering Memory Mode In the event of an alarm the strobe light continues to flash until the panel is reset by the keypad or radio key otherwise it will time out after 72 hours seconds as an indication that you have Disarmed your system If you make
14. a mistake in entering your code then you must press enter and start again Five incorrect entries will cause an alarm Note that user codes can optionally be programmed to be Arm Only codes By definition an Arm Only code can Arm the system but it cannot Disarm See page 18 for User Codes programming f Entry Beeps are programmed on ALARMS DEFINITION Alarms may be caused by A zone has been triggered while Armed A Tamper has been triggered A PANIC button has been triggered All of these may cause your sirens and strobe to operate Various visual indications relevant to the alarm will be retained in the memory If this occurs Disarming your control panel will reset the alarm The cause of the alarm can be identified by entering the Alarm Memory Mode as described on page 15 EJ NESS D8 V4 5 CONTROL PANEL USER MANUAL OPERATION MONITOR MODE LED KEYPAD LCD KEYPAD rmi Press ENTER 4 User Code The e Armed light will flash continuously Only the zones which have been programmed by your installer as Monitor zones will be Armed Q Press oniror JJJ Or User Code B The icon will turn on Only the zones which have been programmed by your installer as Monitor zones will be Armed Monitor mode allows you to Arm selected zones while others are ignor
15. ad Fire Alarm has been enabled by your installer Sends a Fire Alarm report by dialler e If your system is monitored by a central monitoring station If Fire Alarm Report has been enabled by your installer KEYPAD MEDICAL ALARM LED KEYPAD LCD KEYPAD Press C2 Sends a Medical Alarm report by dialler If your system is monitored by a central monitoring station If Medical Alarm Report has been enabled by your installer Medical Alarm does not sound sirens Press 2 E Sends a Medical Alarm report by dialler e If your system is monitored by a central monitoring station If Medical Alarm Report has been enabled by your installer Medical Alarm does not sound sirens NESS D8 V4 5 CONTROL PANEL USER MANUAL E OPERATION LED KEYPAD LCD KEYPAD Q Press Press E A OF User Code Cmm Or User Code The Exclude light will turn on The EXCLUDE icon will turn on Enter the zone number of the zone s to be Excluded Enter the zone number of the zone s to be Excluded Zone No Zone No Zone No E Zone No E The zone light of each Excluded zone will turn on The zone light of each Excluded zone will turn on Press to exit Exclude mode Press to exit Exclude mode The e Exclude light will flash continuously The Z EXCLUDE icon will flash continuously If a
16. e possibility of unwanted alarms but faithfully detects humans PetAware model available QUANTUM 360 Ceiling mounted 360 passive infra red detector with selectable pulse count and sensitivity Provides 8 metre coverage mounted at standard 2 4 metre ceiling height PET AWARE DETECTORS The Ness Quantum Pet Aware PIR Pet Aware Radio PIR and the Pet Aware DUAL are able to discriminate between household pets and unwanted human intruders allowing you to secure your home with your pets indoors PET AWARE Y SIRENS The range of warning devices includes horn speakers polytough siren covers internal screamers and satellite sirens with their own battery backup CCTV The Ness range of Closed Circuit TV equipment includes Dome cameras B W or Colour cameras Miniature hidden cameras Monitors even digital video recorders and remote telephone video systems SWITCHES A variety of switches are available for protecting doors and windows The line up includes surface and flush mount reed switches emergency buttons roller door reed switches and the unique Nessensor vibration sensor for highly effective perimeter protection E NESS D8 V4 5 CONTROL PANEL USER MANUAL WIRELESS PRODUCTS RADIO ACCESSORIES Ask your installer about the range of Ness radio devices for the optional extra convenience of wireless remote control and wireless detection Operating your Ness security system can be as convenient as o
17. ect Each Zone of the panel can be connected to one or more detection devices to protect separate rooms of your premises Detection devices may be connected to the D8 control system directly by cabling or with optional wireless Radio devices Detection devices called Passive Infra Red Detectors or P I R s for short can detect the movement of an intruder by sensing their body heat P I R s are used to cover various critical areas of your premises where an intruder may enter or trespass Another detection device used is called a Reed Switch Reed Switches are attached to windows and doors to detect if a window or door has been opened A Reed Switch consists of a magnet which is normally attached to the moving part of a window or door and the Reed switch which mounts to the door or window frame The panel is Armed when it is set to detect an intruder At other times it is Disarmed Normally a zone is considered Sealed Activation of a detection device will cause the zone to be Unsealed and may cause an alarm Detectors such as fire detectors and panic buttons must be able to generate an alarm at all times regardless of the panel setting A zone with this assignment is called a 24 hour zone Some detection devices may be required to generate an alarm or warning only when the panel is Disarmed A zone with this assignment is called a Day zone Before leaving the premises you must Arm the panel to enable it to detect intrude
18. ed Typically perimeter zones doors and windows can be monitored while you are at home Your installer must program which zones will be active in Monitor mode The panel must be fully Disarmed before Arming in Monitor Mode If an alarm occurs while in Monitor mode entering User Code E will silence the alarm This will also Disarm the panel so remember to enter monitor again if needed Using the optional Radio Keys you can enter Monitor Mode by pressing the OFF button twice within 4 seconds or by pressing the ON button twice within 5 seconds Your installer must enable Radio Key Monitor Arming for this to work NESS D8 V4 5 CONTROL PANEL USER MANUAL E OPERATION KEYPAD PANIC LED KEYPAD z LCD KEYPAD Press C PANIC gt Both keys together Or Pai User Code C ENTER Or PANIC C ENTER If Keypad Panic Shortcut has been enabled by your installer Press C 2 2 Both keys together Or Cx User Code If Keypad Panic Shortcut has been enabled by your installer The keypad PANIC function may have been programmed to be either AUDIBLE activates siren or buzzers or SILENT If your system is monitored by a Central Station sends a PANIC report by dialler If PANIC reports have been enabled by your installer PANIC cannot be used while the panel is in Program Memory or Exclude mode Note Your installer
19. er Code 10 3 to 6 digits User Code 11 3 to 6 digits User Code 12 3 to 6 digits User Code 13 3 to 6 digits User Code 14 3 to 6 digits User Code 15 3 to 6 digits Entry Delay 1 20 seconds 1 to 99 sec Entry Delay 2 60 seconds 10 to 990 sec Exit Delay 60 seconds 1 to 99 sec Follow Me Telephone No Up to 15 digits NOTE The Entry Delay 2 timer programs in 10 second intervals Example if a value of 6 is programmed the time is 60 seconds NESS D8 V4 5 CONTROL PANEL USER MANUAL 19 PROGRAMMING PROGRAMMING USER CODES LED KEYPAD LCD KEYPAD Press P Master Code JJJ Enters Program Mode The PROGRAM light will be on Press P Option No The two digit option number for the code to be programmed The existing code if any will be displayed ddd Press NEW CODE CE J NEW CODE Enter the new code twice The new code will be displayed Press P E a To exit Program Mode Press rocna Master Code ENTER Enters Program Mode The PROGRAM light will be Q Press Option No 22 The two digit option number for the code to be programmed The existing code if any will be displayed Q Press NEW CODE J NEW CODE Enter the new code twice The new code will be displayed Press
20. ess proc C ENTER Press P E To exit Program Mode To exit Program Mode EXAMPLES The panel must be in program mode Program light ON To program the Follow Me Telephone Number to be 9123 1234 POOE 91231234 E To delete the Follow Me Telephone Number POOE MEMORY E NESS D8 V4 5 CONTROL PANEL USER MANUAL EI REMOTE OPERATION OPERATING THE D8 BY TELEPHONE The D8 will allow a user to call in to the panel using a standard DTMF telephone and remotely Arm or Disarm all areas and also turn on or off Aux 1 and Aux 2 To ensure security of operation a user can only carry out remote operations after entering a valid user code WHAT S NEEDED Atelephone with DTMF tones A Valid User code programmed in the D8 The D8 to be connected via Mode 3 Socket to a working telephone line at the installed premises You need to know the telephone number of the line that the D8 is connected to SEQUENCE OF OPERATION 1 Phone the D8 telephone number and listen for the required number of rings ring ring ring ring and then hang up Wait 10 seconds and then call the number again within 50 seconds The D8 will answer the second call immediately sound a beep for 2 seconds then after a pause it will sound a lower frequency tone The D8 is now ready to receive telephone commands Press the 0 button on the telephone This tells the D8 that telephone commands will follow It will re
21. first User codes that are programmed to be Arm Only codes can arm the panel from Monitor mode or from the disarmed state Press OFF button twice within 4 seconds or ON button twice within 4 seconds P69E 5E must be ON Press and hold for 4 seconds P68E 3E amp 4E must be OFF EJ NESS D8 V4 5 CONTROL PANEL USER MANUAL
22. installation Keep in mind that your installation may vary depending on the selected options and equipment The operating instructions which follow will cover the most common options Consult your installation company if you require further information All control panel operations are controlled by the D8 LED or LCD keypad except if an optional key switch or radio control equipment is installed OPERATING RULES Generally the panel will be Disarmed Armed or Monitor modes provide different levels of security for your premises when you are home or away Three other temporary modes Program Memory and Exclude allow you to perform various operations The panel will automatically exit from these temporary modes if you do not press any buttons on the keypad in a 4 minute period If you make a mistake while entering any codes press the Enter or E button and start again When you are required to enter your access code you are given five opportunities to enter it correctly After the fifth invalid attempt the alarm is activated requiring the correct code to silence the alarm This prevents anyone trying to guess your code by entering random numbers AREA OPERATION Area Partitioning allows the 8 zones to be split into two partitions Area1 and Area2 The panel then effectively operates as two separate systems sharing only the siren outputs and dialler USER CODE ASSIGNMENT A User Code assigned to an Area can Arm and
23. may have installed a separate PANIC button To activate the panic alarm simply press that button KEYPAD DURESS ALARM LED KEYPAD Press 9 User Code Disarms and sends a Duress Alarm report by dialler LCD KEYPAD Press 9 User Code Disarms and sends a Duress Alarm report by dialler The DURESS alarm can be used to send a silent alarm to the Central Station that you are being forced to Disarm the panel against your will That is you are disarming under duress To Disarm and send a DURESS alarm prefix your User Code with one of the digits 5 6 8 or 9 when Disarming DURESS IS NORMALLY NOT ENABLED TO ENABLE THE DURESS FUNCTION CONSULT YOUR INSTALLER DURESS ALARMS CAN ONLY USED BY SYSTEMS WHICH ARE MONITORED BY A CENTRAL STATION THE DURESS ALARM CAN BE PROGRAMMED TO SOUND THE INTERNAL SIREN RESET OUTPUT THIS OPTION IS OFF BY DEFAULT 12 NESS D8 V4 5 CONTROL PANEL USER MANUAL OPERATION KEYPAD FIRE ALARM LED KEYPAD LCD KEYPAD Press CD Sounds the siren Fire Alarm siren sound If Keypad Fire Alarm has been enabled by your installer Sends a Fire Alarm report by dialler If your system is monitored by a central monitoring station If Fire Alarm Report has been enabled by your installer Press 3 E Sounds the siren Fire Alarm siren sound If Keyp
24. ng the D8 calls a pre programmed number or numbers and sounds a series of beeps over the phone These beeps can identify the zone or zones which caused the alarm and well as several other alarm types FOLLOW ME TELEPHONE NUMBER The Follow Me Telephone Number is the telephone number to which the D8 sends alarm reports when Audible Monitoring is enabled The Follow Me Telephone Number can be changed by the user in User program Mode If the Follow Me Telephone Number is programmed the Primary and Secondary telephone numbers are ignored even if programmed When Audible Monitoring is enabled See page 19 for information on programming the Follow Me Telephone Number AUDIBLE MONITORING SEQUENCE When triggered by an alarm the D8 will dial the programmed telephone number s and output the audible message for 45 seconds or until it is acknowledged ACKNOWLEDGING THE ALARM The person receiving the call can then acknowledge the alarm by pressing the st key on their telephone Press the key for at least 2 seconds during pauses in the audible message Ifthe alarm is not acknowledged the keypad s LINE light will flash continuously until the panel is next Armed AUDIBLE MONITORING MONITORED PREMISES TELEPHONE LINE ANY TELEPHONE NESS D8 V4 5 CONTROL PANEL USER MANUAL 17 PROGRAMMING Various system options can be programmed by the user These options To enter PROGRAM MODE can only be accessed fr
25. ntrol panel automatically tests the battery every hour and whenever you Arm Disarm the panel Dynamic Battery test Whenever an alarm occurs it may be silenced with a User Code or by optional Radio Keys otherwise it will reset at the end of Alarm Reset Time All alarms are stored in memory and may be viewed at any time by entering Memory Mode NESS D8 V4 5 CONTROL PANEL USER MANUAL EN KEYPAD The D8 control panel may be supplied with either the LED keypad 100 192 or the Ness LCD Keypad 100 667 The keypad provides important visual and audible indications and is the main interface for operating and programming the D8 control panel DISPLAY TEST LCD Keypad only To display all the keypad icons press and hold the E button for at least 2 seconds All the icons will be on whilst the E button is held down Display Test can be activated at any time either in operating mode or any program mode 105mm 4 90mm 4 LED KEYPAD E LCD KEYPAD Backlit LCD 1 2 3 6 9 10 11 14 v D T READY ARMED ARM2 ALARM Zones 1 2 3 4 5 6 7 8 ORedy O O O O O O icon display O Armed O Arm 2 O Memory O Radio O Mains O Exclude O Line MEMORY feu B 80 G Program MONTOR BATTERY MAINS EXLUDE PROGRAM LINE Not Ready light o E PANIC buttons MEMORY button T ARM button PANI
26. om Program Mode Master Code ENTER User Codes may need to be re programmed if a person has forgotten their code to give a new user access to the system or to give someone temporary access P Master Code E User Codes 2 15 can be set as Arm Only Codes These codes can Arm but cannot Disarm the panel Useful for assigning to cleaners tradesmen etc To exit PROGRAM MODE You may need to change the Entry and Exit timers if you find the delays are too long or short ENTER If Audible Monitoring is programmed by your installer the Follow Me Telephone Number is the telephone number the dialler Will call in the event of an alarm P E If your Ness D8 panel is monitored by a Central Station the Follow Me number is ignored For all other programming changes talk to The factory default your installer Master Code is 123 The panel will automatically exit Program Mode is no buttons are pressed within a 4 minute period E NESS D8 V4 5 CONTROL PANEL USER MANUAL PROGRAMMING PROGRAMMING OPTIONS TABLE FACTORY OPTION OPTION No DEFAULT PROGRAMMED User Code 1 Master Code 3 to 6 digits User Code 2 3 to 6 digits User Code 3 3 to 6 digits User Code 4 3 to 6 digits User Code 5 3 to 6 digits User Code 6 3 to 6 digits User Code 7 3 to 6 digits User Code 8 3 to 6 digits User Code 9 3 to 6 digits Us
27. pening your car door The Ness Radio Key provides the benefits of separate ON OFF and PANIC buttons in a slim waterproof remote control Ness radio products require a Ness Radio Interface 100 200 to be fitted to the control panel MADERA AUSTRALIA VOX NESS RADIO KEY 3 BUTTON Fully waterproof ultra slim 3 button Radio Key for remote control of the control panel With separate buttons for ON Arm OFF Disarm and PANIC functions Includes long life lithium battery NESS RADIO KEY PENDANT Fully waterproof pendant style transmitter can be used as a portable wireless Panic button Supplied with a neckchain as well as wristwatch straps Ideal for use as a medical alarm for the elderly or infirm Central Station Monitoring is especially recommended when used for medical alarm purposes Includes long life lithium battery NESS RADIO REED SWITCH Ness Radio Reed Switch for wireless door and window protection Includes long life lithium battery NESS RADIO KEYPAD al A unique fully portable radio keypad The Ness Radio Keypad provides totally wireless Arming Disarming of the Ness D8 D16 amp D24 control panels wee 9 6 oog 05 Also operates Monitor mode and Panic when used with the Ness D16 D24 panels The Ness radio Keypad is suitable for use as a portable keypad or for adding an extra keypad in areas where it is not possible to install wires
28. rs and generate an alarm After arming the panel will ignore detectors during the Exit Delay Time to enable you to depart without triggering an alarm Arming the system may be done through the keypad or with the use of optional Radio Keys for Arming by remote control from outside the premises When you enter the premises the panel will ignore selected zones for the Entry Delay Time and will not alarm unless you don t Disarm the panel during this allowed time Disarming the system may be done by keypad or with the use of optional Radio Keys Monitor mode allows you to Arm selected zones while others are ignored Typically perimeter zones doors and windows can be monitored while you are at home If you wish to split your alarm system into two areas with access limited to each area by code numbers then Area operation is used Radio Keys can also Arm and Disarm Areas The control panel housing and the covers over external sirens are protected by tamper switches to detect someone attempting to disable the security system Activation of these switches will cause an instant tamper alarm If a detector becomes faulty you can Exclude the associated zone so that it is totally ignored and cannot generate an alarm Including the zone will enable it to generate an alarm again The control panel is fitted with a rechargeable stand by battery to ensure your security system continues to operate if the mains power is interrupted This co
29. so on up 30 events Press E to exit Memory mode The D8 Control Panel stores a comprehensive event memory including Arming Disarming Low Battery Mains Fail and Alarm events The memory is constantly upgraded and the last 30 events are always available for viewing This memory display can only be selected while the panel is in the Disarmed state TO CLEAR THE MEMORY LIGHT The MEMORY light flashes continuously when an alarm has occurred as a reminder to view the alarm memory The MEMORY light stops flashing after the memory is viewed as shown above The MEMORY light is automatically cleared next time the panel is Armed MEMORY MODE EVENTS INDICATED BY KEYPAD LIGHTS LIGHT MEMORY EVENT Zone lights 1 8 Zone alarm NIQUES sescenti rette Panel Disarmed ARMED Panel Armed or Area 1 Armed Area 2 Armed MAINS sssssssssseenenetenenntne Mains power failure BATTERY Low Battery TAMPER Tamper alarm Siren cover panel etc EXCLUDE Panic alarm LINE nose Telephone line fail RADIO EXCLUDE Radio Key Panic alarm RADIO BATTERY ZONE Radio Device battery low Device number is indicated by light 1 8 RADIO BATTERY Radio Key battery low Radio Key number is NOT indicated RADIO TAMPER 7 Radio Device
30. spond with either 3 beeps if all OK One long beep means try again Now enter a valid User Code that is normally used for Arming or Disarming the D8 followed by the 3t button The D8 will respond with 3 beeps if it recognises the code or 1 long beep to signal the code was invalid and to try again Enter the required command See Summary Of Telephone Commands Press x st to finish This tells the D8 to hang up Also hang up your telephone EXAMPLE ARMING THE D8 BY TELEPHONE 1 Dial the D8 telephone number Listen for one double ring then hang up 2 Wait 10 seconds then dial the D8 telephone number again The D8 will answer immediately and gives a 2 second beep followed by low tone 3 PRESS 0 To prepare the D8 Jae 3 beeps 4 PRESS User Code to authorise the next command JJ J 3 beeps 5 PRESS 1 to Arm the panel Jaa 3 beeps 6 PRESS to finish and hang up ES NESS D8 V4 5 CONTROL PANEL USER MANUAL REMOTE OPERATION AUDIBLE FEEDBACK JJJ 3 BEEPS The User Code is valid Successful Arming or Disarming An Auxiliary output has been turned ON J 1 LONG BEEP D8 is already Armed Invalid code Try again SHORT An Auxiliary output has been turned OFF SUMMARY OF TELEPHONE COMMANDS Prepare to receive commands st Arm Areas st Disarm Areas Turn Aux 1 Output ON or OFF st Turn Aux 2 Output ON or OFF 4 4
31. tamper alarm Device number indicated by light 1 8 LCD Keypad RADIO MONITOR ZONE Radio Supervision fail Device number is indicated by light 1 8 LED Keypad RADIO ZONE Radio Supervision fail Device number is indicated by light 1 8 NESS D8 V4 5 CONTROL PANEL USER MANUAL 15 RADIO KEY OPERATION NESS RADIO KEY 3 BUTTON The optional Ness Radio Key allows you to Arm Disarm and activate PANIC The Radio Key can also Arm Monitor Mode if this has been enabled by your installer ARMING Press the ON button The keypad will give 3 beeps The outside siren will give 1 chirp If enabled by your installer The strobe light will flash briefly If Monitor Arming by Radio Key is enabled the chirp and flash will be delayed for 5 seconds DISARMING Press the OFF button The keypad will give 3 beeps The outside siren will give 3 chirps If enabled by your installer The strobe light will flash briefly ARMING MONITOR MODE if enabled by your installer Press the OFF button twice within 4 seconds or press the ON button twice within 5 seconds The keypad will give 9 beeps The outside siren will NOT chirp The strobe light will flash briefly PANIC Press and hold the PANIC button for at least 4 seconds The siren and strobe will activate If enabled by your installer The dialler will report a Panic alarm If enabled by your installer and if
32. te 24 Hour Tamper input Single or Double Trigger Zones Remote LED or LCD Keypads Max 3 Fully programmable via the system Keypad Eliminates the need for expensive programmers or Proms Inbuilt Vibration Sensor Analyser All programming data is permanently stored in a non volatile EEprom memory Windows based Up Down load Software allows remote programming and event status True Dynamic Battery Test every time the Panel is armed disarmed and every hour Area Partitionable 2 Areas Any Zone can be programmed to any area as well as common areas Comes complete with an AC plug pack and supports a 12V 7Ah battery to maintain systems security under all power supply conditions Monitor Mode Home Mode Outputs are separately fused with Automatic Reset Fuses Day Mode and Door Chime feature 30 Event Memory Supports 8 Radio Devices Radio PIRs Radio Reeds etc Supports 14 Radio Keys All inputs and outputs are heavily protected against lightning and high voltage supply transients An earth terminal is provided for extra protec tion 15 User Codes Arm only codes can be programmed Programmable Inputs to activate selectable Outputs Designed utilising the latest SMD Technology Simple to Program and Use ES NESS D8 V4 5 CONTROL PANEL USER MANUAL INTRODUCTION The Ness D8 micro computer based 8 zone control panel is the heart of your security system to which all your detection devices conn
33. ust be ON P62E 5E ot User Code User Code Monitor Shortcut must be ON P62E 3E ENTER Or User Code Both keys together or Came User Code C ENTER C PANIC Keypad Panic Shortcut ENTER must be ON P62E 4E 5 6 8 or 9 User Code LCD KEYPAD Arming Shortcut must be ON P62E 5E User Code E User Code Monitor Shortcut E must be ON P62E 3E User Code Cox 2 Cox Both keys together CX D User Code E Cx Keypad Panic Shortcut E must be ON P62E 4E 5 6 8 or 9 User Code E To Disarm and report a Duress Alarm add any of the digits 5 6 8 or 9 before the User Code when Disarming P75E1E must be enabled Exclude Shortcut must be ON P62E 2E or User Code Zone No Enter the zone numbers Zone No to be Excluded To exit Exclude mode Memory Shortcut must be ON P62E 1E gt ENTER Or CHEMORYD User Code Press repeatedly to display the last 30 events ENTER To exit Memory mode ON size 20 User Code E Zone No E Enterthe zone numbers Zone No E to be Excluded E To exit Exclude mode Memory Shortcut E must be on P62E 1E Or User Code E Press repeatedly to display the last 30 events E To exit Memory mode NOTE Normal user codes can arm the panel only if it is fully disarmed
34. xit Delay Time 3 beeps will sound at the end of Exit Delay Time The control panel must be Armed prior to vacating the premises in order to detect intruders The panel must be disarmed and not in Program Monitor Memory or Exclude modes Note If the panel is already in alarm you must first silence the alarm before you can Arm If something is wrong when Arming the control panel the normal 3 beeps will be replaced by other warnings J 10 10 beeps means Mains Power is turned off or the Backup Battery is low J One long beep indicates an invalid entry alarm is outstanding and needs to be reset by entering your User Code first NOTE ARM ONLY codes SIREN WARNING At the end of the exit time all zones should be Sealed If any are Unsealed the siren will sound for 2 seconds as a warning to indicate that those zones have been automatically excluded For maximum security you should return Disarm check the premises and then Arm again Continual warnings could mean that a detector is faulty and may have to be manually excluded If the auto exclude option is disabled the siren will sound for the duration of reset time if a zone is Unsealed at the end of exit time Normal user codes can arm the panel only if it is fully disarmed first User codes that are programmed to be Arm Only codes can arm the panel from Monitor mode or from the disarmed state See page 20 for User Code Programming NES
35. your system is monitored by a central station Press the OFF button to reset a Panic alarm The Ness Radio Key is optional and is not supplied with any Ness control panel as standard Ness radio products require a Ness Radio Interface 100 200 to be fitted to the control panel NESS 08 V4 5 CONTROL PANEL USER MANUAL MONITORING CENTRAL STATION MONITORING The D8 control panel has an on board digital dialler which can send detailed alarm messages to a Central Monitoring Station The digital messages can include information about the zone or zones which caused the alarm tamper alarms low battery or mains failure reports and it can also by user number identify the users who Arm and Disarm the system Central Station Monitoring is highly recommended and is the most effective method of monitoring your D8 alarm system For further information about 24 hour monitoring contact your installer or Ness Security Products CENTRAL STATION MONITORING Nee 1 MONITORED TELEPHONE LINE 1 MONITORING PREMISES i STATION The Primary and Secondary telephone numbers are normally only used for central station monitoring These numbers can only be programmed in Installer Program Mode The Follow Me Telephone Number replaces the Primary AND Secondary telephone numbers AUDIBLE MONITORING The D8 can also be programmed to send audible messages to any telephone or mobile phone When programmed for audible monitori
Download Pdf Manuals
Related Search