5/8-Port Gigabit Ethernet Switch User`s manual
Contents
1. 5 8 Port Gigabit Ethernet Switch User s manual FCC Certifications FC This Equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation CE Mark Warning C This equipment complies with the requirements relating to the EMC Directive 2004 108 EC the Low Voltage Directive 2006 95 EC and the RoHS Directive 2011 65 EU Company has an on going policy of upgrading its products and it may be possible that information in this document is not up to date Please check with your local distributors for the latest information No part of this document can be copied or2. If the device is with wall mount design wall mount installation step is as below 1 Screw the two provided screws into the wall 150 mm apart horizontally Leave a small gap between the head of the screw and the wall The gap should be big enough for the screw heads to slide into the screw slots and the connection cables to run down the back of the switch 2 Align the holes on the back of the switch with the screws on the wall Hang the switch on the screws Product Specifications IEEE802 3 10BASE T IEEE802 3u 100BASE TX IEEE802 3ab 1000BASE T Standard EEEgo2 3x full duplex flow control and back pressure for half duplex IEEE802 3az Energy Efficient Ethernet Interface 5 8 10 100 1000 Mbps Ru 45 ports Network are Data Rate 10 100 1000 Mbps Auto negotiation Transmission 10 100Mbps Full duplex Half duplex Mode 1000Mbps Full duplex Switch 5 P 10Gbps Capacity 8 P 16Gbps Switching 5 P 7 4Mpps Forwarding p Rate 8 P 11 9Mpps MAC Address Table 8K Jumbo Frame 9K bytes Operating 0 C 40 C 32 F 104 F Temperature Storage 20 C 70 C 14 F 158 F Operating 10 90 RH Humidity non condensing Storage 5 90 RH non condensing LED System Power Indications Ports Link Act Power Supply External power adapter 5V 1A Dimensions 150 80 29 8mm Emission FCC CE VCCI Class A 41NE G1080000 A00
3. reproduced in any form without written consent from the company Trademarks All trade names and trademarks are the properties of their respective companies Copyright 2015 All Rights Reserved 2 Introduction The device is a powerful high performance Gigabit Ethernet switch with 5 8 ports capable of 10 100 1000 Mbps auto negotiation operation NWay which means the switch could automatically negotiate with the connected partners on the network speed and duplex mode It is ideal for micro segmenting large networks into smaller connected subnets for improved performance enabling the bandwidth demanding multimedia and imaging applications Moreover the 10 100 1000Mbps auto sensing ability provides an easy way to migrate 10 100Mbps to 1000Mbps network Compared to the shared 10Mbps or 100Mbps networks the switch delivers a dedicated 10 100 1000Mbps connection to every attached client without bandwidth congestion issue This switch also supports auto MDI MDI X function Each port could be used to connect to another switch or hub without crossover RJ 45 cable Store and forward switching mode promises the low latency plus eliminates all the network errors including runt and CRC error packets To work under full duplex mode transmission and reception of the frames can occur simultaneously without causing collisions as well as double the network bandwidth Moreover IEEE 802 3az Energy Efficient Ethernet is
4. supported to save power consumption The switch is plug and play without any software to configure and also fully compliant with all kinds of network protocols Before you start to install the switch check the following contents in this package One Gigabit Ethernet switch One external power adapter Four rubber feet User s Manual RO a Key Features gt Complies with 10BASE T specifications of the IEEE802 3 standard Complies with 100BASE TX specifications of the IEEE802 3u standard Complies with 1000BASE T specifications of the IEEE802 3ab standard 8 10 100 1000Mbps RJ 45 Nway ports Supports MDI MDI X auto crossover Supports full and half duplex operation on all ports Supports back pressure half duplex and full duplex flow control IEEE 802 3x Wire speed packet filtering and forwarding rate Store and forward architecture filters fragment amp CRC error packets Supports extensive LED indicators for network diagnostics Supports Green Ethernet Link On Cable Length Power Saving and Link Down Power Saving Supports IEEE 802 3az LEDs Definition The switch contains one power LED for the device Link Act LED for each port that shows the activities and information of the ports Please refer to the following table for LEDs definition oat Melvins 5 Port Gigabit Switch Cot Milas 8 Port Gigabit Switch 1 8 Port LED Status OLET Power Steady Green
5. The switch is powered on Off The switch is powered off Steady Green __ Valid port connection Valid port connection and Link ACT Blinking Green there is data transmitting receiving Off Port disconnected Station Connection Connect each station to the switch by twisted pair cable Plug one RJ 45 connector into a RJ 45 port of the switch and plug the other RJ 45 connector into the station s network adapter Power on the switch and then system is ready Switches Connection In making a switch interconnection you could use any port to connect another switch with straight or crossover cable As all the ports support auto MDI MDI X function using a straight cable to make a switch to switch connection is allowed For cable selection refer to the following table Network Speed Cable Type Max Length 10Mbps Cat 3 4 5 UTP STP 100 meters 100Mbps Cat 5 UTP STP 100 meters Category 5e 6 1000Mbps UTP STP 100 meters Installation To make this switch perform well we strongly recommend below installation environment 1 The switch is placed with appropriate ventilation environment A minimum 25mm space around the unit is recommended 2 The switch and the relevant components are away from sources of electrical noise such as radios transmitters and broadband amplifiers 3 The switch is away from environments beyond recommend moisture
Download Pdf Manuals
Related Search