USER MANUAL
Contents
1. 1 Under standby mode the LCD will show following FOR MULTIPLE USER MODE ENTER 3 DIGIT No PRESS TO CALL and TO SEARCH FOR NAME PRESS FOR SINGLE USER MODE with one Programmed Residence Name PRESS TO CALL 2 To call a house or specific handset MULTIPLE USER Press the concerned house 3 digit number then press SINGLE USER Just press Note A beep sound will be heard for each valid entry on keypad 3 The LCD will show CALLING and beep sound will be heard At the same time countdown of 20 sec 20 19 18 will be seen on the LCD and in case no reply from the handset after 20 sec the calling process will stop and the visitor can repeat step 2 to call again The LCD will show NO REPLY PLS TRY AGAIN 4 Once the handset replies by pressing the PTT button the LCD will show CONNECTED and the visitor can hear voice of the resident Screen will display LISTEN NOW 5 The visitor should speak only after he hears the two beeps and when the LCD show CONNECTED otherwise some words will be missed by the resident Screen will display SPEAK NOW 6 The handset can reply at any time by pressing and holding the PTT button and speaking into the microphone the LCD will show CONNECTED and the visitor can hear voice of the resident Screen will display LISTEN NOW Note that the PTT Push To Talk button should be pressed properly in before be2. A and cause gate to open Keep the button pressed in for 3 seconds to trigger This long press is a precaution against accidental triggering 5 Lock B button K5 During communication with gate station pressing K5 can activate dry contact B with 300mA rating to close momentarily for 3 sec The LCD will show door open icon with letter B for 5 sec once the gate station successfully receives this command signal Under standby mode pressing K5 can also activate dry contact B Keep the button pressed in for 3 seconds to trigger This long press is a precaution against accidental triggering 6 Call alert ring type select button K6 a b c d e Press K6 to select the preferred type of call alert from below Vibration only Visual light only Ringing tone only Vibration Visual light Visual light Ringing tone f Vibration Ringing tone g Vibration Visual light Ringing tone 7 Volume Up K7 and Volume down K9 Press K7 and K9 to select your preferred volume The ringing tone volume will also be adjusted accordingly 8 Ringing tone time select button K8 Press K8 to select the time of ringing tone when the handset is being called Selecting 10 seconds means you will hear 4 times of DING DONG Selecting 15 sec means 6 times and selecting 20 sec means 8 times In case there is more than one handset paired with the same house no this ringing tone time must be set same for all handsets or it will follow the lo
3. please refer to Figure above 1 Handset calling button K1 To call another handset paired with the same house no press K1 three beep sound will be heard Speak only after these three beep sound release K1 when finish talking to hear reply from opposite party This is a push to talk button so the button must remain pressed in whilst you speak directly into the microphone Hang up Power ON OFF button K2 This button has two functions a Hang up after communicating with gate station Both handset and gate station will return back to standby mode b Power ON OFF Long press of K2 for 4 seconds will switch on or off the handset Call reply Calling gate station button PTT K3 When receiving a call from gate station press K3 to start communicating with visitor Each time K3 is pressed a two beep sound will be heard Speak only after these two beep sound or the visitor will miss out some words Under standby mode press K3 can directly speak to the gate station However the gate station cannot talk back This is a push to talk button so the button must remain pressed in whilst you speak directly into the microphone Lock A button K4 During communication with gate station pressing K4 can activate relay A with lamp rating and cause the gate to open The LCD will show door open icon with letter A for 5 sec once the gate station successfully receives this command signal Under standby mode pressing K4 can also trigger relay
4. Zartek CDP 808 Multi Wireless Intercom System Users Manual ZA 610 Gate station complete including power supply relay board and external antenna ZA 611 Back side Gate station including power supply relay board and external antenna ZA 612 Programming kits including cable and software ZA 613 Handsets with charger ZA 613 E Handsets with external antenna for maximum range and charger Overview The Zartek Wireless Multi Intercom System is newly developed and three years of R amp D in the making It is fully approved by ICASA Applications for this system include housing complexes apartments and office blocks large estates long driveways etc This system can accommodate 80 separate channels Communication is initiated from the gatestation by selecting a 3 digit code such as 001 or 901 and pressing the button Only the selected houses handset will ring and communication is established Communication is simplex so only one person can speak at a time but the gatestation s microphone is always active so the visitor does not have to press any key to speak The inside handset can enter into the conversation at any time by pressing a PTT button There are 2 triggers that can be activated from the handset for opening a motorized gate or striker lock Multiple handsets can be added for the same house to have internal communication Range is terrain dependant and is 100m in built up areas and 350m in more open areas The external antenna is moun
5. an additional gatestation to be used on another or the same entrance for instance to be notified when visitors want to exit The functions of the back gatestation are similar to the front station as all the same names and codes are stored on the station Gate triggering is limited in that a call has to be initiated from the back gatestation in order to be able to trigger the gate it is connected to A system busy function can also be added to the back gatestation with a hard wire connection between gatestations This is used so that the visitor can be notified if the system is busy with another call and they must wait Handset The handset is portable and rechargeable giving you the convenience of answering the gate from anywhere in the house garden and pool A large LCD screen indicates house number ring type incoming or outgoing calls door opening etc Each handset includes a mains adaptor charging cradle and rechargeable battery Communication is very clear and working range is typically 350m in built up areas and 800m line of sight Operation of the handset is essentially like a two way radio as all communication is done via a PTT button Handsets are able to receive communication from the gatestation once a call is active and respond by pressing the PTT button A call can be made to the gatestation at any time even when the system is idle This feature is used to contact a guard by the gate Handsets are also able to communicate with oth
6. er handsets in the same house if they all share the same code As many handsets can be added and all will ring when a call is made from the gate There are 2 gate release buttons on the handset to trigger separate gates Each handset is given a unique 3 digit code when it is programmed to the gatestation This code is the handsets number or house s unit number Different coded handsets cannot speak to each other Installation of battery and charger The handset is equipped with a removable rechargeable battery pack Unscrew battery cover and place battery as described on the battery Plug the mains adaptor into the wall socket and connect the other end to the desktop charging cradle There is an indicator light on the desktop charger which flashes when charging and remains on when full Charging time is approximately 4 hours and the handset can be always placed in the charger to keep it powered up always with a trickle charge A battery level indicator on the screen will show the battery level and charging status Once the handset is removed from the charger the battery life is approximately 5 hours with average use Doorbell visual light K7 Volume up button K6 Call alert select button Zartek K1 Handset calling button K4 Lock A button K8 Ringing tone time select button K5 Lock B button K2 Hang Up Power ON OFF button Microphone K3 Call reply Calling gate station button K9 Volume down button Speaker Function of buttons
7. gate station calls all handsets will start to show call alert sign Only one handset can answer the call the remaining handsets will enter Tx inhibit mode so as not to interfere with the communication To activate relay A or dry contact B press K4 or K5 respectively The gate open icon X18 will show up momentarily in LCD together with the respective letter A or B once the gate station receives such command successfully Upon finishing communication the resident can hang up by momentarily pressing K2 Both handset and gate station will return to standby mode In case the resident forgets to hang up the handset will hang up by itself approximately 1 minute after no activity has been detected on any button During a call all other handsets in the system programmed with different house no will enter Tx inhibit mode so as to avoid interference to the call under progress Under standby mode the handset can speak to the gate station by pressing PTT K3 but the gate station cannot talk back The handset can also activate relay A or dry contact B by long press of K4 or KS If there are more than one handset programmed with same house no the handset can call each other by pressing K1 The battery can be charged up by placing handset in the supplied charger stand During charging the red LED on the charger stand starts flashing and turns steady green once the battery is fully charged up Beep sound will be heard for each valid entry of butto
8. ginning to speak 7 Whenever the LOCK A button K4 on handset is pressed the door lock will be triggered and LCD show DOOR A OPENED 8 Whenever the LOCK B button K5 on handset is pressed the dry contact will be closed momentarily and LCD show DOOR B OPENED 9 When the HANG UP button K2 on handset is pressed the communication between gate station and handset will stop and the unit will return to standby mode In case the unit cannot receives hang up signal from handset either due to interference from other device or the resident forgets to hang up it will automatically hang up and return to standby mode 60 sec after no signal has been received from handset 10 To search for names and house no of residents press The LCD will show the residents name and associated house no in alphabetical order Press UP DOWN key to turn page Once you located the name press the associated house no and then 11 Resident door entry code The residents can open the DOOR LOCK A by pressing followed by the programmed 4 digit secret door entry code The LCD will show DOOR ENTRY CODE and the gate will open 12 Infrared detector Whenever the infrared detector detects movement 1 3 m with people approaching towards unit or 2 5m with people walking across unit the LCD and keypad will be active and light up If there is no further movement it will turn off after 15 seconds Back gatestation It is possible to add
9. n
10. ngest time 9 Trigger Lock Disable Function K1 K6 Press K1 while holding down K6 the lock icon will show up the keys K4 and K5 will be locked and non functioning i e you will be unable to open the door lock A and B Press again K1 while holding down K6 will activate K4 and K5 again the lock icon will go off Call from Door Trigger Operating Gatestation AorB Ring type channel 4 N PE A eg a Handset Volume House Volume House Battery sending call level Number Level Operation 1 When the gate station calls to a particular handset or house no the concerned handset will show the call alert sign as selected by K6 and the gate station calling icon X15 starts flashing in the LCD 10 11 The resident can reply the call by pressing PTT K3 Now handset signal icon will stay on and the transmit icon lightning shows up every time K3 is pressed Speak only after the two beeps sound or otherwise the visitor will loose some of your words Release K3 after finish speaking and the unit enters reception mode with the transmit icon going off and receive icon showing up in LCD The resident can speak to the visitor anytime they prefer by pressing K3 In case the handset does not reply the call within the time period as set by the ringing tone time 10 sec or 15 sec or 20 sec both handset and gate station will return back to standby mode automatically For house no paired with more than one handset whenever the
11. sitor can speak from 1m from the gatestation and does not need to exit the car During a call the handset can enter into the conversation by pressing a PTT push to talk button There are 2 gates that can be triggered from the handset and the screen will show which gate A or B has been opened There is a search function on the gatestation in case the visitor does not know the house number The screen indicates how to search Press to enter search mode and use the arrows to find the name and house number Once the number is located press the 3 digit code and to call A door entry code can be used to trigger the gate directly from the gate station A motion sensor will detect visitors coming within 3m of the gatestation and the screen and keypad will light up and be active There is a back up battery fitted into the gatestation which will power the unit for 4 hours in case of a power outage The installer will be equipped with the programming cable or pin codes to program the gatestation Any changes to displayed names house numbers or additional handsets can be made via gatestation programming Outline of call procedure Visitor presses 3 digit code and key on gatestation to call Handset rings and resident answers by pressing PTT Visitor speaks when prompted Resident presses PTT to speak or Lock A or B to trigger gate Resident ends call LCD Alphanumeric keys oe ke DE key DOWN ke ENTER key UP key Operation
12. ted as high as possible for improved coverage and audio Refer to this manual for in depth understanding of the operation on the gatestation and handset In short the visitor must press a 3 digit code corresponding to the houses handset The handset will ring flash and or vibrate and the resident should then answer by pressing the PTT button Now communication is established Visitors can speak when prompted to on the LCD screen and residents can speak back by pressing the PTT button A gate is opened by pressing the Door lock A or B button and then the call can be ended Handsets can be left on in the charger as there is smart charging Gate Station The gatestation is used to call a particular house Each house is given a code 000 999 there can be a maximum of 100 separate codes units per gatestation The visitor enters a 3 digit code and presses the key to call a house Even if the house number is the visitor must enter a 3 digit code such as 001 A countdown timer will start and the station will return to standby if there is no answer If there is an answer from a handset a private communication channel is set up The communication is simplex meaning only one person can speak at a time The visitor does not have to press any buttons as the microphone is always active on the gatestation once the call is active There are prompts on the screen when to listen and when to speak Sensitivity of the gatestation microphone is very high so the vi
Download Pdf Manuals
Related Search