User Manual
Contents
1. Keep the device at least 6 ft 1 8 m away from the nearest source of electromagnetic noise such as a photocopy machine Connect to the Data Ports 1 Insert one end of the Ethernet cable into a switch port 2 Connect the other end into the Ethernet port of the device 3 Insert the voice grade copper wire between one pair of Ethernet Extenders via the Ethernet Extender port RJ 11 connector or terminal block One device must be set to LOC mode and the other to Auto mode when two devices are connected PWR Per 20 lt gt 3 29290 _ sl 0000 10 100 LOC ASM 100 80 Une Front panel of the extender LEDs on the extender LED Color Status PWR Green ON Receiving power OFF Power off Ethernet Extender Port Link Activity Green ON Connection is established OFF No connection is established Flashing Port is sending or receiving data Per Green ON Performance mode OFF Standard mode RMT Green ON Remote mode LOC Green ON Local mode SYM Green ON Symmetric mode Page 6 724 746 5500 blackbox com Quick Start Guide LEDs on the extender continued LED Color Status Ethernet Extender Port continued ASM Green ON Asymmetric mode Line Speed Green ON Displays the link speed in Mbps 10 100TX port Link Activity Green ON Valid network connection OFF No data transmission on port Flashing Port is sending or receiving data2. Las instrucciones de seguridad y operaci n deber n ser guardadas para referencia futura Todas las advertencias en el aparato el ctrico y en sus instrucciones de operaci n deben ser respetadas Todas las instrucciones de operaci n y uso deben ser seguidas El aparato el ctrico no deber ser usado cerca del agua por ejemplo cerca de la tina de ba o lavabo s tano mojado o cerca de una alberca etc El aparato el ctrico debe ser usado nicamente con carritos o pedestales que sean recomendados por el fabricante El aparato el ctrico debe ser montado a la pared o al techo s lo como sea recomendado por el fabricante Servicio El usuario no debe intentar dar servicio al equipo el ctrico m s all a lo descrito en las instrucciones de operaci n Todo otro servicio deber ser referido a personal de servicio calificado El aparato el ctrico debe ser situado de tal manera que su posici n no interfiera su uso La colocaci n del aparato el ctrico sobre una cama sof alfombra o superficie similar puede bloquea la ventilaci n no se debe colocar en libreros o gabinetes que impidan el flujo de aire por los orificios de ventilaci n El equipo el ctrico deber ser situado fuera del alcance de fuentes de calor como radiadores registros de calor estufas u otros aparatos incluyendo amplificadores que producen calor El aparato el ctrico deber ser connectado a una fuente de poder s lo del tipo descrito en el i
3. Speed Yellow ON Link speed at 100 Mbps OFF Link speed at 10 Mbps Distance and data rate for the Ethernet Extender port Distance and Data Rate Distance m Data Rate Mbps 300 100 400 80 600 60 800 40 1200 20 2600 1 This distance data rate information is measured according to a testing standard in the laboratory The actual installation will be affected by the quality of the copper wire and the impact of noise disturbance The connection speed will be affected 4 Apply DC Power Connect the supplied AC to DC power adapter to the receptacle on the rear panel of the Ethernet Extender and then attach the plug into a standard AC outlet DIP Switches eo o MER o 12VDC Figure a Bakpe heeii DIP Switch 2 Ci DIP Switch 3 Performance Standard 724 746 5500 blackbox com Page 7 Chapter 1 Specifications 1 Specifications Table 1 1 Specifications Technology Standards Forward and Filtering Rate Processing Type Auto negotiation Power Input Mechanical Casing Dimensions Weight Mounting Interface Connectors DIP Switch LED Indicators Standards IEEE 802 3 VOBASET IEEE 802 3u 100BASE TX IEEE 802 3x full duplex and flow control 10 Mbps 14 880 pps 100 Mbps 148 810 pps Store and Forward Half duplex back pressure and IEEE 802 3x full duplex flow control Auto MDI MDI X 12 VDC DC jack 4 2 W max Consump
4. 2560 ft 800 m 40 Mbps 3840 ft 1200 m 20 Mbps 8320 ft 2600 m 1 Mbps 724 746 5500 blackbox com Page 9 Chapter 2 Overview 2 Overview 2 1 Introduction Your Industrial Ethernet Extender is a state of the art IEEE compliant network solution designed for users who require high performance to eliminate bottlenecks and increase productivity To simplify installation the Industrial Ethernet Extender is shipped ready for use 2 2 Features Has 1 10 100BASE TX Ethernet port with an RJ 45 connector Auto negotiates speed and duplex mode on the Ethernet port Auto MDIX on Ethernet port Complies with IEEE 802 3 10BASE T and IEEE 802 3u 100BASE TX standards Has 1 Ethernet Extender port with an RJ 11 connector or terminal block e Ethernet Extender port auto senses the speed e DIP switch configures Ethernet Extender Auto or Local mode Symmetric or Asymmetric mode and Performance or Standard mode e Status LEDs Uses an external AC to DC power adapter included 2 3 What s Included Your package should contain the following items If anything is missing or damaged contact Black Box Technical Support at 724 746 5500 or info blackbox com e Industrial Ethernet Extender e 1 external power adapter e A printed Quick Start Guide NOTE You will need two extenders to complete the application The full user manual installation guide the document you are reading can be downloaded from the Black B
5. a commercial environment Operation of this equipment in a residential area is likely to cause interference in which case the user at his own expense will be required to take whatever measures may be necessary to correct the interference Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment This digital apparatus does not exceed the Class A limits for radio noise emission from digital apparatus set out in the Radio Interference Regulation of Industry Canada Le pr sent appareil num rique n met pas de bruits radio lectriques d passant les limites applicables aux appareils num riques de la classe A prescrites dans le Reglement sur le brouillage radio lectrique publi par Industrie Canada Disclaimer Black Box Network Services shall not be liable for damages of any kind including but not limited to punitive consequential or cost of cover damages resulting from any errors in the product information or specifications set forth in this document and Black Box Network Services may revise this document at any time without notice 724 746 5500 blackbox com Page 3 N In OM Statement strucciones de Seguridad Normas Oficiales Mexicanas Electrical Safety Statement 1 2 3 4 5 oN Oo o 10 11 Todas las instrucciones de seguridad y operaci n deber n ser le das antes de que el aparato el ctrico sea operado
6. and other information 724 746 5500 blackbox com Page 13 Chapter 3 Installation 3 Installation 3 1 Preparing the Site Before you install your Industrial Ethernet Extender be sure your operating environment meets the operating environment requirements in Table 3 1 Table 3 1 Site requirements Characteristics Requirements Mounting Desktop installations Provide a flat table or shelf surface DIN Rail installations Top hat type 35 mm Wallmounting installations Mounting on the wall Access Locate the Industrial Ethernet Extender in a position that lets you access the front panel RJ 45 and Ethernet Extender port view the front panel LEDs and access the rear panel power connector Power source Provide a power source within 6 feet 1 8 meters of the installation location Power specifications for the Industrial Ethernet Extender are shown in Chapter 1 Be sure that the AC outlet is not con trolled by a wall switch which can accidentally turn off power to the outlet and the Industrial Ethernet Extender Environmental Temperature Install the Industrial Ethernet Extender in a dry area with ambient temperature between 14 and 140 F 10 and 60 C Keep the Industrial Ethernet Extender away from heat sources such as direct sunlight warm air exhausts hot air vents and heaters Operating Humidity The installation location should have a maximum relative humidity of 95 non condensing Ventilation Do not restrict ai
7. 0 seconds away at 724 746 5500 or blackbox com BLACK BOX About Black Box Black Box provides an extensive range of networking and infrastructure products You ll find everything from cabinets and racks and power and surge protection products to media converters and Ethernet switches all supported by free live 24 7 Tech support available in 60 seconds or less O Copyright 2015 Black Box Corporation All rights reserved Black Box and the Double Diamond logo are registered trademarks of BB Technologies Inc Any third party trademarks appearing in this manual are acknowledged to be the property of their respective owners LB320A user manual version 1 724 746 5500 blackbox com
8. LB320A lt gt BLACK BOX Customer Order toll free in the U S Call 877 877 BBOX outside U S call 724 746 5500 Support FREE technical support 24 hours a day 7 days a week Call 724 746 5500 or fax 724 746 0746 Information www blackbox com info blackbox com Trademarks Used in this Manual Trademarks Used in this Manual Black Box and the Double Diamond logo are registered trademarks of BB Technologies Inc Any other trademarks mentioned in this manual are acknowledged to be the property of the trademark owners We re here to help If you have any questions about your application or our products contact Black Box Tech Support at 724 746 5500 or go to blackbox com and click on Talk to Black Box You ll be live with one of our technical experts in less than 60 seconds Page 2 724 746 5500 blackbox com FCC and IC RFI Statements Federal Communications Commission and Industry Canada Radio Frequency Interference Statements This equipment generates uses and can radiate radio frequency energy and if not installed and used properly that is in strict accordance with the manufacturer s instructions may cause interference to radio communication It has been tested and found to comply with the limits for a Class A computing device in accordance with the specifications in Subpart B of Part 15 of FCC rules which are designed to provide reasonable protection against such interference when the equipment is operated in
9. e ore dn eve hada de d eee onda 10 2 4 Hardware Descrip erica 11 EMI SI IM 14 Bel Ie 14 3 2 Installing the Industrial Ethernet Extender o eem pt rr m eg rari ur pi eo ed ec eds rte eae 14 3 3 Connecting to the 10 100 Mbps RJ 45 Port alius serans sese a iaria a a aai DAE 14 3 4 Connecting to the Ethernet Extender Port sssssssssssssssssssseeeeeeeneeneeeeeeneene nennen ener en n en enters 15 35 Checking the STAIN eek cts ao liceo eo ate 15 3 6 Applying AC POWED RR 15 a 16 4 1 Troubleshooting Tips A 16 4 2 Additional Troubleshooting SUGGESTIONS ai dd 17 421 COMU MOM ita db 17 4 2 2 Industrial Ethernet Extender Integrity ici tte nadie 17 4 2 3 AUto NegolLlatiOni sprites pred eet fea bate Daba 17 724 746 5500 blackbox com Page 5 Quick Start Guide Quick Start Guide Unpacking Unpack the items Your package should include e One LB320A Industrial Ethernet Extender e This printed quick start guide If items are missing or damaged contact Black Box Technical Support at 724 746 5500 or info blackbox com Keep the carton and packing material Select a Location e Installation Desktop Wallmount DIN Rail mount e Identify a power source within 6 feet 1 8 meters e Choose a dry area with ambient temperature between 14 and 140 F 10 and 60 C e Keep away from heat sources sunlight warm air exhausts hot air vents and heaters Be sure there is adequate airflow
10. h Ethernet specifications Check for a defective adapter card cable or port by testing them in an alternate environment where all products are functioning Symptom File transfer is slow or performance degradation is a problem Cause Half or full duplex setting on the Industrial Ethernet Extender and the connected device are not the same Solution Configure the Industrial Ethernet Extender and the attached device to auto negotiate Symptom A segment or device is not recognized as part of the network Cause One or more devices are not connected properly or cabling does not meet Ethernet guidelines Solution Verify that the cabling is correct Be sure all connectors are securely positioned in the required ports Equipment may have been disconnected accidentally Symptom Collisions are occurring on the connected segment Cause Some collisions are normal when the connection is operating in half duplex mode Solution Recheck the settings of the device attached to the Industrial Ethernet Extender port Be sure the Industrial Ethernet Extender and the attached device are using the same duplex setting Be sure the Industrial Ethernet Extender and the attached device are set to auto negotiate Symptom Link Activity LED is flashing continuously on all connected ports and the network is disabled Cause A network loop redundant path has been created Solution Break the loop by ensuring that there is only one path from any networked dev
11. ice to any other networked device Page 16 724 746 5500 blackbox com Chapter 4 Troubleshooting 4 2 Additional Troubleshooting Suggestions If the suggestions in Section 4 1 do not resolve your problem refer to the troubleshooting suggestions in this section 4 2 1 Configuration If problems occur after altering the Industrial Ethernet Extender s network configuration restore the original connections and determine the problem by implementing the new changes one step at a time Be sure cable distances repeater limits and other physical aspects of the installation do not exceed the Ethernet limitations 4 2 2 Industrial Ethernet Extender Integrity If required verify the integrity of the Industrial Ethernet Extender by resetting it 4 2 3 Auto Negotiation The 10 100 Mbps ports negotiate the correct duplex mode and speed since the Industrial Ethernet Extender is configured for auto negotiation this is the Industrial Ethernet Extender s default setting and the device at the other end of the link supports auto negotiation If the device does not support auto negotiation the Industrial Ethernet Extender determines only the speed cor rectly and the duplex mode defaults to half duplex 724 746 5500 blackbox com Page 17 NOTES Page 18 724 746 5500 blackbox com NOTES 724 746 5500 blackbox com Page 19 Black Box Tech Support FREE Live 24 7 Tech support the way it should be Great tech support is just 6
12. nstructivo de operaci n o como se indique en el aparato 12 Precauci n debe ser tomada de tal manera que la tierra fisica y la polarizaci n del equipo no sea eliminada 13 Los cables de la fuente de poder deben ser guiados de tal manera que no sean pisados ni pellizcados por objetos colocados Sobre o contra ellos poniendo particular atenci n a los contactos y recept culos donde salen del aparato 14 El equipo el ctrico debe ser limpiado nicamente de acuerdo a las recomendaciones del fabricante 15 En caso de existir una antena externa deber ser localizada lejos de las lineas de energia 16 El cable de corriente deber ser desconectado del cuando el equipo no sea usado por un largo periodo de tiempo 17 Cuidado debe ser tomado de tal manera que objectos liquidos no sean derramados sobre la cubierta u orificios de ventilaci n 18 Servicio por personal calificado deber ser provisto cuando A El cable de poder o el contacto ha sido da ado u B Objectos han ca do o l quido ha sido derramado dentro del aparato o C El aparato ha sido expuesto a la lluvia o D El aparato parece no operar normalmente o muestra un cambio en su desempe o o E El aparato ha sido tirado o su cubierta ha sido da ada Page 4 724 746 5500 blackbox com Table of Contents Table of Contents QUICK STANT GUID APA o o A 6 A 8 PS IE ANN 10 ZPMMInieeticie mE 10 2 2 EedlBlleS A IM EE MEM 10 2 3 Whats Included ui s rettet bte dt the dan Pat
13. on the Industrial Ethernet Extender configures the RJ 45 port automatically to enable communica tions with the attached device without requiring user intervention Ethernet Extender Port The LB320A Industrial Ethernet Extender has one Ethernet Extender port RJ 11 connector or terminal block see Figure 2 1 Insert the voice grade copper wire between one pair of Ethernet Extenders via the Ethernet Extender port RJ 11 connector or ter minal block One device must be set to LOC mode and the other to Auto mode when two devices are connected Upstream e Remote setting SYM Local setting SYM Wi Downstream ireless AP Setting AUTO Setting AUTO Figure 2 5 Symmetric mode The data rate for upstream and downstream is the same and is suitable for network extension Upstream es q U Remote setting ASM Local setting ASM IP D camera Setting AUTO OEE Setting LOC Figure 2 6 Asymmetric mode The data rate for downstream is more than the data rate of upstream and is usable for IP camera applications Upstream ang S Links to 4G LTE access point Remote setting Per Down irear Local setting Per Setting AUTO Setting AUTO Figure 2 7 Performance mode Use this mode for high speed data transmission when the line quality is good Upstream m emn 0 E Remote setting Std Local setting Std PLC Downstream Setting AUTO Setting AUTO Upstream and downstream transmission rates a
14. ox Web site To download from the Web site 1 Go to www blackbox com 2 Enter the part number in the search box 3 Click on the Resources tab on the product page and select the document you wish to download Page 10 724 746 5500 blackbox com Chapter 2 Overview 2 4 Hardware Description Figures 2 1 through 2 4 show the front and back panels of the extender units Tables 2 1 and 2 2 describe the extender s components Use the extenders in pairs one unit is configured as the local unit and the other unit is configured as the remote unit PWR Per 20 gt RMT SYM 60 40 LOC ASM 100 80 Figure 2 2 Back panel of the extender Table 2 1 Extender components Number in Figure 2 1 Description 1 Links to 10 100 Mbps Ethernet 2 Indicate status at a glance See Table 2 3 for details 3 Links to Ethernet line 4 Links to Ethernet line 5 6 Front Panel Features 10 100 Mbps RJ 45 Port The LB320A Industrial Ethernet Extender has one 10 100 Mbps RJ 45 port see Figure 2 1 This port is an auto sensing auto MDIX 10 100 Mbps port When you insert a cable into an RJ 45 port the Industrial Ethernet Extender e Determines whether the cable is a straight through or crossover cable e Automatically ascertains the maximum speed 10 or 100 Mbps and duplex mode half or full duplex of the attached device 724 746 5500 blackbox com Page 11 Chapter 2 Overview After determining this informati
15. ply power e All green Link Activity LEDs blink momentarily The green Power LED goes ON The Link Activity LEDs for every port connected to a device flash as the Industrial Ethernet Extender conducts a brief Power On Self Test POST After the Industrial Ethernet Extender passes the POST the Link Activity LEDs for every port connected to a device go ON The Industrial Ethernet Extender is now functional and ready to pass data If the Power LED is not ON check that the power adapter is plugged in correctly and that the power source is good and not con trolled by a wall switch If this does not resolve the problem see Chapter 4 Troubleshooting 724 746 5500 blackbox com Page 15 Chapter 4 Troubleshooting 4 Troubleshooting 4 1 Troubleshooting Tips Symptoms causes and solutions of possible problems are described below Symptom The Power LED is off Cause The Industrial Ethernet Extender is not receiving power Solution Check the power adapter connections for the Industrial Ethernet Extender and the connected device Be sure all cables used are correct and comply with Ethernet specifications Symptom Link Activity LED is OFF or intermittent Cause The port connection is not working Solution Check the crimp on the connectors and be sure the plug is inserted properly and locked into the port at both the Industrial Ethernet Extender and the connecting device Be sure all cables used are correct and comply wit
16. r printer network storage or other network device Page 14 724 746 5500 blackbox com Chapter 3 Installation 3 4 Connecting to the Ethernet Extender Port The front panel of the Industrial Ethernet Extender provides one RJ 11 connector or Terminal Block see Ethernet Extender Port on page X To prevent ESD damage follow normal board and component handling procedures To connect the Extender s Ethernet port Insert the voice grade copper wire between one pair of Ethernet Extenders via Ethernet Extender port RJ 11 connector or Terminal Block Set one device to LOC mode and the other to Auto mode when two devices are connected 3 5 Checking the Installation Before you apply power e Inspect the equipment thoroughly Verify that all cables are installed correctly Check cable routing to make sure the cables are not damaged or do not create a safety hazard Be sure all equipment is mounted properly and securely 3 6 Applying AC Power Before you connect the power adapter select an AC outlet that is not controlled by a wall switch which can turn off power to the Industrial Ethernet Extender After you select an appropriate outlet use the following procedure to apply AC power 1 Connect the female end of the supplied AC power adapter cable to the power receptacle on the back of the Industrial Ethernet Extender 2 Connect the 3 pronged end of the AC power adapter cable to a grounded 3 pronged AC outlet When you ap
17. re similar Figure 2 8 Standard mode Use this mode for long distance with more noise immunity when the line quality is poor or the noise interferes with the cable Page 12 724 746 5500 blackbox com LEDs Chapter 2 Overview The LB320A front panel LEDs show power and link activity status Table 2 3 summarizes the LEDs on the Industrial Ethernet Extender Rear Panel LED PWR Ethernet Extender Port Link Activity Per RMT LOC SYM ASM Line Speed 10 100TX po Link Activity Speed Table 2 3 Front panel LEDs on the extender Color Green Green Green Green Green Green Green Green rt Green Yellow Status ON Receiving power OFF Power off ON Connection is established OFF No connection is established Flashing Port is sending or receiving data ON Performance mode OFF Standard mode ON Remote mode ON Local mode ON Symmetric mode ON Asymmetric mode ON Displays the link speed in Mbps ON Valid network connection OFF No data transmission on port Flashing Port is sending or receiving data ON Link speed at 100 Mbps OFF Link speed at 10 Mbps The LB320A rear panel has a receptacle for connecting the supplied external power adapter Use only the external power adapter supplied with the Industrial Ethernet Extender Bottom Pa nel The LB320A bottom panel has a product label that shows regulatory compliance product serial number
18. rflow by covering or obstructing the rear and side panels of the Industrial Ethernet Extender Keep at least 2 inches 5 08 centimeters free on all sides for cooling Operating Conditions Keep the Industrial Ethernet Extender at least 6 ft 1 83 m away from nearest source of electromagnetic noise such as a photocopy machine Stacking If you intend to stack two or more Industrial Ethernet Extenders be sure e The mounting surface can safely support the stack e There is adequate space around the stack for ventilation and cooling 3 2 Installing the Industrial Ethernet Extender You can install your Industrial Ethernet Extender on a flat surface DIN Rail or wall with other equipment If installing the Industrial Ethernet Extender on a desktop shelf DIN Rail or wall allow sufficient ventilation space between the device and the objects around it The LB320A Industrial Ethernet Extender s dimensions are 0 94 H x 3 16 W x 4 3 D 2 38 x 8 03 x 10 92 cm 3 3 Connecting to the 10 100 Mbps RJ 45 Port The front panel of the Industrial Ethernet Extender provides one 10 100 Mbps RJ 45 port see 10 100 Mbps RJ 45 Port on page X To prevent ESD damage follow normal board and component handling procedures To connect devices to the Industrial Ethernet Extender s 10 100 Mbps RJ 45 port 1 Insert one end of a Category 5 or better Ethernet cable into a Ethernet port 2 Insert the other cable end into the Ethernet port of a compute
19. tion Aluminum case IP30 0 94 H x 3 16 W x 4 3 D 2 38 x 8 03 x 10 9 cm 0 33 Ib 0 15 kg DIN rail top hat type 35 mm or wallmounting Ethernet Port 1 10 100BASE TX port Ethernet Extender Port 1 RJ 11 and terminal block port DIP Switch 1 Auto Local mode DIP Switch 2 Symmetric Asymmetric mode DIP Switch 3 Performance Standard mode Per unit Power Status Ethernet Extender port Link Activity Per RMT LOC SYM ASM Line Speed Page 8 724 746 5500 blackbox com Chapter 1 Specifications Table 1 1 Specifications continued Environment Operating Temperature 14 to 140 F 10 to 460 C Storage Temperature 40 to 4 185 F 40 to 4 85 C Ambient Relative Humidity 5 to 9596 noncondensing Approvals ISO Manufactured in an ISO facility Safety UL60950 1 EN60950 1 EMI FCC Part 15B Class A EN61000 6 4 EN55022 EN61000 3 2 EN61000 3 3 EMS EN61000 6 2 ESD Standard EN61000 4 2 Radiated RFI Standards EN61000 4 3 Burst Standards EN61000 4 4 Surge Standards EN61000 4 5 Induced RFI Standards EN61000 4 6 8 Magnetic Field Standards EN61000 4 8 Environmental Test Compliance Vibration Resistance IEC60068 2 6 Fc Shock IEC60068 2 27 Free fall with package FED STD 101C Method 5007 1 Table 1 2 Data Rate Specifications Distance feet meters Data Rate Mbps 960 ft 300 m 100 Mbps 1280 ft 400 m 80 Mbps 1920 ft 600 m 60 Mbps
Download Pdf Manuals
Related Search