UltraShortThrowWallMount User manual
Contents
1. Projector Alignment To adjust yaw swivel Loosen screw on projector mount assembly J indicated below until projector mount can be rotated Rotate mount to desired position and retighten screw To adjust pitch forward and backward tilt Turn knob on back of mount as shown below Pull knob out and turn by hand for easy adjustment or insert 2 phillips screwdriver in end of knob and turn To adjust roll side to side tilt Turn knob on side of mount as shown below Pull knob out and turn by hand for easy adjustment or insert 2 phillips screwdriver in end of knob and turn ARROW INDICATES FRONT OF MOUNT SCREW FOR YAW SWIVEL STOP BACK OF MOUNT KNOBFORROLL T ADJUSTMENT b i JUS fig 16 1 To prevent tampering with the pitch and roll adjustments Tighten the two tamper resistant security screws on the projector mount assembly J using 4 mm security allen wrench V to lock the pitch and roll adjustments as shown below NOTE Tighten screws firmly but do not overtighten Overtightening can damage the mount 16 1 e Do not adjust pitch or roll while tamper resistant security screws are fully engaged Loosen the two tamper resistant security screws one complete turn before adjusting the projector mount assembly or damage may occur TOLOCK ROLLTIGHTEN TAMPER RESISTANT 2 V TOLOCKPITCHTIGHTEN SECURITY SCREW TAMPER RESISTANT i SECURITY S2. Hook brackets E into adapter plate D as shown in fig 8 1 and To remove screen from mount loosen safety security screws and lift screen off of mount Do not tighten screws with excessive force Overtightening can cause damage to mount Tighten screws to 40 in lb 4 5 N M maximum torque D It BOTTOM OF HOOK BRACKET E E D JE T DETAIL 5 Da SIDE VIEW fig 8 1 DETAIL 6 Disengage connection block from projector mount assembly J by unscrewing captive screw and sliding out connection block as shown CAPTIVE CONNECTION SCREW 11 of 16 ISSUED 08 08 08 SHEET 055 9094 1 Visit the Peerless Web Site at www peerlessmounts com For customer care call 1 800 865 2112 or 708 865 8870 Arrow on projector mount assembly J indicates front of mount The arrow of projector mount assembly J should face towards the round tube on projector arm C Fasten projector mount assembly J to projector arm C using two 1 4 20 x 1 0 hex head screws N four 0 25 ID nylon washers P and slide plate I as shown in fig 10 2 and 10 3 Do not tighten 1 4 20 x 1 0 hex head screws N fully to allow for adjustment Insert rectangle plug S into projector arm C as shown in fig 10 2 Position projector mount assembly J so that hole corresponding to your size screen in projector arm C is in the center of projector mo
3. CREW H 7 ji Pai ra l FRONT VIEW SIDE VIEW 16 of 16 ISSUED 08 08 08 SHEET 055 9094 1 Visit the Peerless Web Site at www peerlessmounts com For customer care call 1 800 865 2112 or 708 865 8870 2008 Peerless Industries Inc All rights reserved Allother brand and product names are trademarks or registered trademarks of their respective owners
4. ECTOR TOP MOUNTING HOLES SCREEN y N BOTTOM OF SCREEN FLOOR fig 1 1 CHART Screen Size Dimension X Visit the Peerless Web Site at www peerlessmounts com For customer care call 1 800 865 2112 or 708 865 8870 Installation to Wood Stud Wall Installer must verify that the supporting surface will safely support the combined load of the equipment and all attached hardware and components Tighten wood screws so that wall plate is firmly attached but do not overtighten Overtightening can damage the screws greatly reducing their holding power Never tighten in excess of 80 in Ib 9 N M Make sure that mounting screws are anchored into the center of the stud The use of an edge to edge stud finder is highly recommended Hardware provided is for attachment of mount through standard thickness drywall or plaster into wood studs Installers are responsible to provide hardware for other types of mounting situations Make sure that the mounting holes are on the stud centerline Drill six 5 32 4 mm dia holes 2 1 2 65 mm deep Fasten two 14 x 2 5 wood screws Q into top mounting holes leaving a 25 of exposed thread as shown Hook wall mount assembly A onto 14 x 2 5 wood screws Q as shown in fig 2 1 Fasten four 14 x 2 5 wood screws Q into wall mount asse
5. S FRONT OF PROJECTOR Attach adapter plate H to projector using four M6 x 12 mm serrated washer head socket pin screws L and 0 25 spacers M NOTE Shoulder of connection block indi cates the back of projector The screws L P should be placed in the center of slots This can be adjusted during final projector L alignment if needed SHOULDER CONNECTION BLOCK PROJECTOR 14 of 16 ISSUED 08 08 08 SHEET 055 9094 1 Visit the Peerless Web Site at www peerlessmounts com For customer care call 1 800 865 2112 or 708 865 8870 Attaching Adapter Plate to Projector Mount Do not lift more weight than you can handle Use additional man power or mechanical lifting equipment to safely handle placement of the projector Slide connection block with projector into projector mount assembly J as shown Tighten captive screw to secure projector to projector mount assembly J ARROW INDICATES FRONT OF MOUNT CONNECTION FRONT OF MOUNT CAPTIVE SCREW IMPORTANT For security installations insert one 10 32 x 1 4 socket pin screw W through projector mount assembly J and into connection block as shown Tighten screw using 4mm security allen wrench V CONNECTION BLOCK 15 of 16 ISSUED 08 08 08 SHEET 055 9094 1 Visit the Peerless Web Site at www peerlessmounts com For customer care call 1 800 865 2112 or 708 865 8870
6. ctor tube 1 055 1839 projector arm 055 1830 adapter plate 055 1828 hook bracket 055 1840 vertical handle 055 1834 horizontal handle 055 1835 projector adapter plate 055 1822 CARRIAGE slide plate 055 1821 projector mount PRG 1 10 32 x 0 375 phillips screw 520 1130 C M6 x 12 mm serrated washer head socket pin screw 510 1050 0 25 ID spacer 590 1050 1 4 20 x 1 0 hex head screw 520 1606 10 32 x 3 8 serrated washer head socket pin screw 520 1151 0 25 ID nylon washer 540 9460 14 x 2 5 wood screw 5 1 015 C03 acorn nut 530 1049 plug 590 1303 10 32 x 1 3 8 socket pin screw 510 1098 alligator anchor 590 0097 5 32 4 mm security allen wrench 560 9646 W 10 32 x 1 4 socket pin screw 520 1196 X flanged bushing 590 1271 Y retainer bushing 055 1836 Parts may appear slightly different than illustrated lt CHAMDWOTVOZSCMHAGS TO9MoOVS gt 3 of 16 ISSUED 08 08 08 SHEET 055 9094 1 Visit the Peerless Web Site at www peerlessmounts com For customer care call 1 800 865 2112 or 708 865 8870 Parts List Continued Make sure that wall mount assembly A is level use it as a template to mark the top two mouting holes Alternatively the top two screws can be fastened 16 apart as detailed in step 2 while making sure that they are level In order to set the desired height of bottom of screen in the lowest position refer to dimension X from the chart below PROJ
7. le location for 77 screen is shown in fig 5 2 Securely tighten all four 10 32 x 0 375 phillips screws K O K DETAIL 1 K a NOTE 77 hole location shown 63 will use second from bottom hole on vertical handle F 77 SCREEN k 63 SCREEN fig 5 1 Fasten horizontal handle G to vertical handle F using four 10 32 x 0 375 phillips screws K and two acorn nuts R Acorn nuts R go on below horizontal handle G 9 of 16 ISSUED 08 08 08 SHEET 055 9094 1 Visit the Peerless Web Site at www peerlessmounts com For customer care call 1 800 865 2112 or 708 865 8870 Insert hook brackets into screen as shown in detail 2 and fig 7 1 Secure each hook bracket E with M6 x 12 mm serrated washer head socket pin screw L as shown in fig 7 2 and detail 3 KL SCREEN h BRACKET ae AOREEN 63 SCREEN R E 77 SCREEN a RS DETAIL 2 fig 7 1 DETAIL 3 Visit the Peerless Web Site at www peerlessmounts com For customer care call 1 800 865 2112 or 708 865 8870 detail 4 The hooks will go over the flange on the top and the bottom of hook bracket E into the slots as shown in detail 4 and detail 6 Fasten 10 32 x 1 3 8 socket pin screws T on each hook bracket E using security allen wrench V and tighten to wall plate as shown in detail 5 O
8. mbly A as shown in fig 2 2 Make sure that the wall mount assembly A is level tighten all six 14 x 2 5 wood screws Q Skip to step 3 CARRIAGE CARRIAGE 5 of 16 ISSUED 08 08 08 SHEET 055 9094 1 Visit the Peerless Web Site at www peerlessmounts com For customer care call 1 800 865 2112 or 708 865 8870 Installation to Solid Concrete or Cinder Block e When installing Peerless wall mounts on cinder block verify that you have a minimum of 1 3 8 of actual concrete thickness in the hole to be used for the concrete anchors Do not drill into mortar joints Be sure to mount in a solid part of the block generally 1 minimum from the side of the block Cinder block must meet ASTM C 90 specifications It is suggested that a standard electric drill on slow setting is used to drill the hole instead of a hammer drill to avoid breaking out the back of the hole when entering a void or cavity e Concrete must be 2000 psi density minimum Lighter density concrete may not hold concrete anchor e Make sure that the supporting surface will safely support the combined load of the equipment and all attached hard ware and components Use wall mount assembly A as a template to mark mouting holes Drill six 5 32 4 mm dia holes to a concrete minimum depth of 2 5 65 mm Insert six anchors U in surface holes flush with wall as shown right Fasten two 14 x 2 5 wood screws Q in
9. nd flanged bushing X to Y wall mount assembly A using two E 10 32 x 0 375 phillips screws K X assembly A and secure with two 1 0 32 x 0 375 phillips screws K as shown below NOTE Use correct set of mounting holes for the screen size as shown below 63 SCREEN gt NOTE Twist tube A i into wall mount assembly A Slide projector tube B into top of wall mount K THREE THREADS EXPOSED LA fig 4 1 Wate Hook adapter plate D onto three 10 32 x 0 375 phillips screws K O CARRIAGE as shown in fig 4 2 NOTE Tube B should wall mount assembly A 77 SCREEN i B Wye Fasten three 10 32 x 0 375 phillips o screws K into adapter plate D as shown in fig 4 2 Securely tighten all six 10 32 x 0 375 phillips screws K CARRIAGE fig 4 3 8 of 16 ISSUED 08 08 08 SHEET 055 9094 1 Visit the Peerless Web Site at www peerlessmounts com For customer care call 1 800 865 2112 or 708 865 8870 Fasten two 10 32 x 0 375 phillips screws K into adapter plate D leaving three threads exposed as shown in detail 1 Hook each vertical handle F onto 10 32 x 0 375 phillips screw K as shown in fig 5 1 NOTE Use top slot for 77 screen or second slot from top for 63 screen Fasten 10 32 x 0 375 phillips screws K through lower slot of vertical handle F that lines up with the lower hole in adapter plate D Ho
10. peerless Installation and Assembly Wallmount for CPA100 and Whiteboard Model A100IWBMOUNT Maximum Load Capacity for Screen 53 Ib 24 kg Maximum Load Capacity for Projector 13 5 Ib 6 kg 3215 W North Ave Melrose Park IL 60160 800 865 2112 or 708 865 8870 Fax 708 865 2941 www peerlessmounts com NOTE Read entire instruction sheet before you start installation and assembly Do not begin to install your Peerless product until you have read and understood the instructions and warnings contained in this Installation Sheet If you have any questions regarding any of the instructions or warnings please call Peerless customer care at 1 800 865 2112 This product should only be installed by someone of good mechanical aptitude has experience with basic building construction and fully understands these instructions Make sure that the supporting surface will safely support the combined load of the equipment and all attached hard ware and components Never exceed the Maximum Load Capacity See page one If mounting to wood wall studs make sure that mounting screws are anchored into the center of the studs Use of an edge to edge stud finder is highly recommended Always use an assistant or mechanical lifting equipment to safely lift and position equipment Tighten screws firmly but do not overtighten Overtightening can damage the items greatly reducing their holding power Carriage bo
11. to top anchors U leaving a 25 of exposed thread for each screw Q as shown Hook wall U mount assembly A onto 14 x 2 5 wood screws Q as shown in fig 2 3 Fasten four 14 x 2 5 wood screws Q into wall mount assembly A as shown Make sure that the wall mount assembly A is level tighten all six 14 x 2 5 wood screws Q Skip to step 3 Place wall mount assembly A over anchors U and Tighten screws so that wall mount is firmly attached secure with screws Q but do not overtighten Overtightening can damage screws greatly reducing their holding power Never tighten in excess of 80 in Ib 9 N M Always attach concrete anchors directly to load bearing concrete Never attach concrete anchors to concrete covered with plaster drywall or other finishing material If mounting to concrete surfaces covered with a finishing surface is unavoidable the finishing surface must be counterbored as shown below Be sure concrete anchors do not pull away from concrete when tighten ing screws If plaster drywall is thicker than 5 8 A LER custom fasteners must be supplied by installer INCORRECT CORRECT CARRIAGE G concrete concrete o U 1 8 ie _ Easter oo i re eee ee oe drywall i O A U aes 6 of 16 ISSUED 08 08 08 SHEET 055 9094 1 Visit the Peerless Web Site at w
12. unt assembly J as shown in fig 10 1 Securely tighten both 1 4 20 x 1 0 hex head screws N NOTE This can be adjusted during final projector alignment if needed fig 10 2 77 SCREEN ARROW INDICATES FRONT OF MOUNT 63 SCREEN a ee Bottom View fig 10 1 C FRONT VIEW fig 10 3 12 of 16 ISSUED 08 08 08 SHEET 055 9094 1 Visit the Peerless Web Site at www peerlessmounts com For customer care call 1 800 865 2112 or 708 865 8870 Place projector arm C onto projector tube B as shown in fig 11 1 Align projector arm C so that the holes in projector tube B are in the middle of projector arm C slot NOTE This can be adjusted during final projector alignment if needed Fasten projector arm C to projector tube B using two 10 32 x 3 8 serrated washer head socket pin screws O as shown in fig 11 2 and detail 6 DETAIL 6 fig 11 2 13 of 16 ISSUED 08 08 08 SHEET 055 9094 1 For customer care call 1 800 865 2112 or 708 865 8870 Visit the Peerless Web Site at www peerlessmounts com Attaching Adapter Plate to Projector Align shoulder on connection block opposite notch in CONNECTION ine plate H Attach adapter plate H to LN BLOCK connection block from projector mount assembly J CF using two 10 32 x 3 8 serrated washer head socket i SHOULDER pin screws O NOTCHINDICATE
13. ww peerlessmounts com For customer care call 1 800 865 2112 or 708 865 8870 CUTAWAY VIEW Installation to Metal Stud Wall Metal Stud Accessory Kit ACC 615 Required Drywall must be 1 2 or thicker and metal stud must be 24 gauge or thicker e Installer must verify that the supporting surface will safely support the combined load of the equipment and all attached hardware and components Drill six 1 2 holes through drywall and metal studs NOTE It may be necessary to drill 5 32 pilot holes prior to drilling 1 2 holes Refer to instruction sheet included with Peerless accessory kit ACC 615 for metal studs to install togglers Fasten two 1 4 20 x 2 1 2 screws into top mounting holes leaving a 25 of exposed thread on each as shown in fig 2 4 Hook wall mount assembly A onto 1 4 20 x 2 1 2 screws Fasten four 1 4 20 x 2 1 2 screws into wall mount assembly A as shown in fig 2 5 Make sure that the wall mount assembly A is level tighten all six 1 4 20 x 2 1 2 screws TOGGLER CARRIAGE CARRIAGE fig 2 5 7 of 16 ISSUED 08 08 08 SHEET 055 9094 1 Visit the Peerless Web Site at www peerlessmounts com For customer care call 1 800 865 2112 or 708 865 8870 Fasten three 10 32 x 0 375 phillips K screws K to carriage leaving three threads exposed Attach retainer bushing Y a
14. x has over 100 Ibs 43 kg of pressure Be careful not to pinch fingers This product is intended for indoor use only Use of this product outdoors could lead to product failure and personal injury This product was designed and intended to be mounted to the following supporting surfaces checked below with the hardware included in this product as specified in the installation sheet To mount this product to an alternative support ing surface contact Peerless customer care at 1 800 865 2112 This product was designed to be installed on the following wall construction only WALL CONSTRUCTION ADDITIONAL HARDWARE REQUIRED Wood Stud None Wood Beam None Solid Concrete None Cinder Block None Metal Stud Do not attach except with Peerless accessory kit for metal studs Contact Customer Service for Peerless accessory kit for metal studs Brick Contact Customer Service Other or unsure Contact Customer Service Tools Needed for Assembly stud finder edge to edge stud finder is recommended phillips screwdriver drill 1 4 bit for concrete and cinder block wall 1 2 bit for metal stud wall 5 32 bit for metal or wood stud wall level 2 of 16 ISSUED 08 08 08 SHEET 055 9094 1 Visit the Peerless Web Site at www peerlessmounts com For customer care call 1 800 865 2112 or 708 865 8870 Before you begin make sure all parts shown are included with your product Parts List A Description Qty Part wall mount assembly 055 1841 proje
Download Pdf Manuals
Related Search