(SAVE THESE INSTRUCTIONS)
Contents
1. berPower Reliability Quality Value Cy Automatic Voltage Regulator Models V Armor600E 1000E 1500E 2000E User s Manual K0O1 C000035 00 IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS This manual contains important safety instructions Please read and follow all instructions carefully during installation and operation of the unit Read this manual thoroughly before attempting to unpack install or operate your V Armor CAUTION To prevent the risk of fire or electric shock install in a temperature and humidity controlled indoor area free of conductive contaminants See the specifications for the acceptable temperature and humidity range CAUTION To reduce the risk of overheating the V Armor do not cover the V Armor s cooling vents and avoid exposing the unit to direct sunlight or installing the unit near heat emitting appliances such as space heaters or furnaces CAUTION Do not plug the V Armor input into its own output CAUTION Do not allow liquids or any foreign object to enter the V Armor Do not place beverages or any other liquid containing vessels on or near the unit CAUTION In the event of an emergency press the OFF button and disconnect the power cord from the AC power supply to properly disable the V Armor CAUTION Unplug the V Armor prior to cleaning and do not use liquid or spray detergent INSTALLING YOUR V Armor SYSTEM UNPACKING The box should contain the following 1 V2. Armor Unit x 1 2 Power Cord x 1 3 User Manual x 1 Applications The V Armor automatically corrects brownouts by boosting low voltage and over voltages by stepping down high voltage from the power utility service to levels that are safe for computers as well as other sensitive equipment The V Armor provides the highest degree of protection from line voltage sags and swells The total power consumption of all equipment plugged into the V Armor must not exceed the Maximum Output Power Capacity rating listed in the Specifications table BASIC OPERATION FRONT PANEL DESCRIPTION 1 Power Switch Press the power switch to turn the ON OFF V Armor 2 Normal Mode LED The green LED will light when utility power is normal 3 AVR Mode LED The yellow LED will light when utility power is abnormal and the unit will work in AVR mode The yellow LED will flash every 3 seconds when input line voltage is not in acceptable range and the unit will switch off the outputs 4 Fault LED The red LED will light when fault or over load occurs REAR PANEL DESCRIPTION 1 AC Inlet Connect to utility power through the input power cord Input Circuit Breaker The circuit breaker provides optimal overload protection AC outlet The V Armor provides outlets for connected equipment to insure temporary uninterrupted operation during a power failure and against surges and spikes 4 Fan The V Armor provides fan for heat dissipatio
3. n for V Armor1000E 1500E 2000E TECHNICAL SPECIFICATIONS Input Voltage Range 165Vac 278Vac Frequency 50 60Hz Output Output Voltage 220 230Vac 10 Regulation Operating Relative 0 to 90 Humidity Physical Maximum Dimensions 150 x 120 x 200 mm HxWxD mm CYBERPOWER GREENPOWER TECHNOLOGY CyberPower s Green Commitment CyberPower is dedicated to the development of green products and has adopted Green practices throughout its business including membership in Climate Savers Computing Initiative CSCI accordance with the Restriction on Hazardous Substances ROHS Waste Electrical and Electronic Equipment WEEE protocols as well as ISO 14001 and IECQ QC080000 CyberPower pledges to provide the A Dios y advanced energy solution for the environment and become a leading eco friendly organization in the V Armor industry lt Reduce Energy Cost with GreenPower Technology CyberPower s goal is not only to provide eco friendly products but also to bring the best value for consumers The advanced energy saving design improves the operating_efficiency and eliminates waste energy consumption As a result consumers will enjoy significant energy cost savings with the adoption of GreenPower technology TROUBLESHOOTING Possible Cause Solution _ O The V Armor The unit is not connected to an The unit must be connected to a AC outlet 220 230V 50 60Hz outlet will not turn Con
4. tact CyberPower Systems Technical on Mechanical problem Support Input circuit breaker is effective Outlets do not Reset the input circuit breaker provide power to equipment Unit has been damaged by a Contact CyberPower Systems Technical surge or spike Support For more information visit www cpsww com All rights reserved Reproduction without permission is prohibited ce zB A
Download Pdf Manuals
Related Search