DPS202 Guide - Brahler ICS UK Ltd.
Contents
1. UNITS S8G Sockets 1 4 for connection of maximum 40 Delegate Units CDS200 2 generation at each line maximum 80m cable length to the first unit PC IN CR15 socket for connection of a control PC PC LINK CR15 socket temporarily not in use Additional earth connection Copyright by Br hler ICS CDS200 II DPS202 4 Connectors The Central Control Unit has an automatically mains voltage setting of 90 250 Volts by 50 60 Hz If N there is another voltage range you must not connect this eguipment It has to be ensured that all cables are installed in cable ducts or that they are fixed by cable clamps or adhesive tape in such a way that there is no danger of somebody falling over them 4 1 Mains power connecter 90V 250V 50Hz 60Hz Connect the delivered mains cable with this socket to ensure the proper working of the Central Control Console DPS202 4 2 Audio AF LINK connector S8G IN OUT Two DIN S8G sockets for linking the audio AF signal if more O 0 O O than one Central Control Units are connected together Cables 000 O Q Q are available on request 0 2 O90 AF LINK 4 3 EXT LS IN connector XLR G EXT LS IN XLR socket for feeding an external signal for decentralized public address Each delegate unit DC10 EDC10 and EDC9 has an incorporated loudspeaker for this purpose EXT LS IN Copyright by Brahler ICS 11 DPS202 CDS200 II 4 4 MIXER PA line out connector XLR OUT 1 all OUT 2 OUT 3 O2. E Mail rental braehler com Sales Tel 49 0 2244 930 100 Fax 49 0 2244 930 450 E Mail sales braehler com Copyright by Br hler ICS DPS202 39 DPS202 Notes 40 CDS200 II Copyright by Br hler ICS CDS200 II DPS202 Copyright by Br hler ICS 41 brahler Phone 49 2244 930 0 www braehler com DPS202 04 0303
3. hler ICS AG K nigswinter with following statements Reason for return repair or credit note Exact declaration of the goods exact no of pieces article no model serial no Price which was invoiced by us better our invoice no with date Return shipments from Non EU countries have to be sent either by air freight to Cologne airport to the attention of Calenberg Oversea Logistics Mrs Taxacher Welser Str 8 51449 K ln Tel 49 2203 3592 838 or by the following courier services DHL Express Federal Express TNT Worldwide Express UPS Express Please do not use any other courier service because only the four companies mentioned above perform return shipments To enable quick and cost efficient customs clearance kindly take care that the airway bill mentions a return for repair as well as b the customs tariff code number of the goods which will be advised by us together with the return of material authorization number Any expenses duties and taxes incurred by deviant handling will be charged to the sender Copyright by Br hler ICS 37 CDS200 II Contact Information Company and branch offices Head office Germany BR HLER ICS Konferenztechnik International Congress Service AG P O Box 3264 D 53627 K nigswinter Wahlfelder M hle 3 D 53639 K nigswinter Tel 49 0 2244 930 0 Fax 49 0 2244 930 450 www braehler com Rental service Tel 49 0 2244 930 200 Fax 49 0 2244 930 430
4. addition to the manual numbering first time implemented in CDS200 Il is the fully automated numbering of delegates units This feature enables a fast starting up of the equipment For system enhancement up to 5 8 as option Central Control Units can be linked together The unit consists of a 19 housing 2HU On the front panel of the Central Control Console DPS202 there is a POWER switch with a green ON LED which shows the ON status The four green LEDs 48VDC L1 to L4 indicate the correct line output supply If one or more LEDs do not light up you will be informed that there is a voltage breakdown on the corresponding line Please check the cabling and the connected units first The failure can not be removed by switching on and off the DPS This could damage the output line Also do not plug and unplug the connector of the faulty line The four yellow LEDs AF indicate audio signal AF activity on the corresponding line L1 to L4 With the help of a large LC Display and eight push buttons the system configuration can be made Copyright by Br hler ICS 9 DPS202 CDS200 II Rear view The Central Control Unit contains the following sockets on the rear side Mains power connector AF LINK 2 x S8G socket for coupling the AF signals of more than one Central Control Unit linked together EXT LS IN XLR socket for internal decentralized sound reinforcement MIXER PA 4 x XLR socket for up to 4 separate AF lines to the mixer
5. in version of delegate unit with MIC function e BC202 50 Microphone control panel for 50 microphones e BC202 100 Microphone control panel for 100 microphones Can be integrated at any point within the chains All BC202 s have their own ID number Copyright by Br hler ICS 31 DPS202 CDS200 II CDS200 PC with conference software Ha EDC10 elegate units DPS202 C C C DC10 Sg e O delegate units aa Sh jo n NN pr um E m E RS aft a KERR U 2 z 4 separate audio lines e E p EDC9 Lemmer ven delegate units AN MIC delegate units with incorporated loudspeaker PA recording etc Application 2 This diagram shows an extended application for a discussion system in conjunction with a voting system The DPS is controlled by a PC with Brahler ICS software MicControl under MS Windows CDS200 II System Components e CDS200 II PC Including MicControl Software e DPS202 Central Control Unit with 4 line outputs e DC10 Delegate unit with MIC function e EDC9 Delegate unit with MIC and VOTING function e BC202 50 Microphone control panel for 50 microphones e BC202 100 Microphone control panel for 100 microphones Optional e Mixing console Possibility to connect each output line of the DPS to a mixer console Can be integrated at any point within the chains All BC202 s have their own ID number CDS200 II DPS202 CDS200 PC with conference softw
6. the connection unit see semi automatic numbering figure 18 Units lost see figure 5 and 6 One or more microphone units are Check the power supply for the lost not recognized by the central control units unit Check data communication figure 25 and power by means of MIC LED all ON Check whether a unit has been removed Copyright by Brahler ICS CDS200 II DPS202 Warranty BRAHLER ICS allows for the CDS200 II products a warranty period of 24 months from date of delivery for faulty materials and or manufacturing faults The warranty does not include rechargeable or disposable batteries misuse negligence breakage wrong installation use outside the existing rules and any unauthorised modifications BR HLER ICS rejects any guarantee if the safety label with the serial number is removed BR HLER ICS declares itself to agree to exchange or repair defective components due to faulty materials or manufacturing dependent on following procedure 1 The client declares that the fault is not due to empty discharged wrongly inserted or faulty batteries 2 Before sending the faulty product back to the company please obtain an RMA Return Material Authorisation number An RMA can be obtained by contacting us at the details below Phone 49 0 2244 930 0 or email sales braehler com 3 You may send the defective product free of charge to refer to the service form BR HLER ICS Konferenztechnik International
7. 02 software via PC or Laptop the mode PC REMOTE is required Copyright by Br hleries CDS200 Il DPS202 By pressing SET button 6 in STAND ALONE mode the next menu is shown S a gt S 8 Figure 9 By selecting one of the buttons 1 to 3 the corresponding sub menus are called Pressing button 6 will scroll to the next page Figure 16 5 2 1 MIC Modes Adjustment of microphone mode button 1 Figure 9 S a 5 el 8 Figure 10 In application STAND ALONE the following microphone modes can be selected AUT NEXT means that the next delegate will be switched online as soon as a speaker slot is available When all slots are occupied the next speakers requests are saved The corresponding LED at the delegates units is blinking AUT FLOAT mean that the first speaker will be replaced by the last speaker if maximum number of speakers slot has been reached FIFO With button 6 the maximum number of active delegates can be changed Press to toggle from 1 to 6 NO PRIO means that there is no president aligned jet see also default values Copyright by Brahler ICS 17 DPS202 CDS200 Il 5 2 2 MIC ROUTING Microphone Routing Button 2 Figure 9 me a Ee ES Figure 11 In this menu the microphone input signals are allocated to the different outputs The outputs L1 to L4 either can be all routed to XLR OUT1 as one sum signal Figure 11 When OUT1 is switched to LINK all other
8. 44 Operation 4 LEDs for 4 LEDs for power buttons Mic signal indication indication Mains power indication Earth Mains Fan grille External LINE OUT1 to connection Power LS IN OUT4 PC LINK C15 PC Connectors for 4 connectors for Input AF LINK delegate units Figure 45 Copyright by Brahler ICS 27 DPS202 CDS200 II 7 1 Technical Data DPS202 The DPS202 is complying with international standard IEC 60914 Connectors e EXTLS IN XLR socket for decentralized public address e MIXER PA OUT1 all OUT2 OUT3 and OUTA four XLR plug for up to 4 AF Lines e UNITS 1 4 two S8G socket for connection of maximum 40 Delegates units CDS200 2 generation at each line maximum 80m cable length to the first delegate unit e AF LINK IN and OUT two S8G socket for coupling the AF signals of more than one Central Control Unit connected together e PCIN CR15 socket for connection of a control PC e PCOUT CR15 socket temporary not in use Features e Green lighted mains switch for power on indication e LC Display in 4 rows each 20 characters e 4green LEDs for power on indication at the outputs e 4yellow LEDs for Peak MIC level Short circuit protected outputs e Short circuit lt 2s Current limit at 1 5A max per output e Short circuit gt 2s output will switch OFF e 60s for switching the output ON again if the short circuit has been removed Power Supply e Mains power 90 250 VAC 50 60 Hz e Power consump
9. 8 will select the semi automatic programming of the delegate units like shown in Figure 21 In this mode the first unit to program is selected with button 6 down or 7 up Please notice that maximum Number is 245 op Copyright by Brahler ICS CDS200 Il DPS202 Figure 21 Figure 22 ENTER button 8 will lead to the operation mode semi automatic numbering Figure 23 Please wait until all units are prepared Figure 22 Er ER ER Figure 23 NEXT 001 means the next ID number of unit to program for instance 001 The programming is done by pressing the microphone key of all connected units successively The illuminated microphone of the unit will be deactivated and again activated after a second When done with the last unit press OK button 5 5 2 5 System Setup Chairman Allocation of chairman unit Button 3 Figure 17 The number of the chairman sometimes called president can be allocated Any user defined unit can be assigned as a chairman s unit a 2 EN ata ma Figure 24 Set the number of the chairman s unit with button 6 and 7 Button 5 OK confirms your input and leaves this menu Only one chairman per system is possible Another allocation will override the former one Alternatively somebody may press the microphone button of the designated unit The number of this unit will be displayed accordingly Copyright by Br hler ICS 21 DPS202 CDS200 II 5 3 Test Routines after pressing
10. Congress Service AG Auf der Alten Burg 6 53639 K nigswinter Germany 4 Should it turn out that the fault was caused through inattentiveness or inappropriate use the service and shipping charges will be added to the clients account Copyright by Br hler ICS 35 DPS202 36 CDS200 II Copyright by Br hler ICS MONIIN brahler Material return shipments for repair service or guaranty purposes please send to BRAHLER ICS Konferenztechnik AG Auf der Alten Burg 6 D 53639 K nigswinter Germany Phone 49 0 2244 930 100 Fax 49 0 2244 930 450 Dear customer Please ask our sales staff for the RMA number Return of Material Authorization Without RMA number a treatment is not possible Please always include this service form fully completed with any complaint or repair wish you may have Please note that only returns with the proper and complete paperwork can be dealt within time A detailed fault description will reduce costs and period of repair Please contact us before you return eguipment in order to find the most efficient way of sending RMA number Article description Serial no Code Delivery note no Invoice no Reason for return Fault description Company Contact person Phone Fax Notes Comments Transport damages have to be reported immediately to the responsible forwarding agent Remarks for Non EU customers Please add to each return a delivery note or a proforma invoice addressed to Br
11. UT 4 MIXER PA Four LINE outputs XLR plug for connection to an external mixer for recording purposes or to provide a PA system 4 5 UNITS 1 4 line connector S8G UNITS Four output connectors S8G sockets for the delegate units or other devices of the CDS200 II 2 generation system At each line you can connect up to 40 devices For more units you have to couple another Central Control Unit DPS202 for an extended system The cable is part of each delegate unit 4 6 PC IN C15 Input C15 socket for connection of a control PC via RS232 COM port O 00000000 O 09000000 PC IN 4 7 PC LINK C15 Output C15 socket not in use O 00060000 0000000 PC LINK Copyright by Br hler ICS CDS200 II DPS202 4 8 Connecting to earth PAN For an additional earth connection only for signal ground there is a ground screw besides the 4 mains power connector gt Copyright by Br hler ICS 13 DPS202 CDS200 Il 5 Starting Up The power supply is turned on via the power switch on the front side of the Central Control Unit DPS202 When the Control Unit is used the first time it is recommended to control the setup The procedure is described in the following If the DPS202 was already in use connected to a control panel BC202 and VIPs were assigned in this session but forgot to clear those before disconnect the BC202 the VIPs will be still active In this case a reset Fig 3 is mandatory to reset DPS to de
12. are EDC10 e gt E delegate units PP ADI UNITS ES DC10 E ai COM _PC IN p me 4 n gt NN N NU COM oe en n amp delegate units RI LV Maa fst t wc Up to 160 units in 4 rows e en a EDC9 g Pa we delegate units l l l MIC delegate units with incorporated loudspeaker a PC INSE m 1 t aa es Application 3 This diagram shows an application linking more than one central unit DPS202 in PC Remote mode Itis a discussion system in conjunction with a voting system The DPS is controlled by a PC with Br hler ICS software MicControl under MS Windows With this configuration you can use up to 5 x 160 delegates units see also 5 1 4 2 page 21 Note As option it is possible to connect 8 DPS devices to a PC with 8 COM port CDS200 Il System Components e CDS200 II PC Including MicControl Software e DPS202 Central Control Unit with 4 line outputs e DC10 Delegate unit with MIC function e EDC1O0 flush mounted version with MIC function e EDC9 flush mounted version with MIC and VOTING function e BC202 50 Microphone control panel for 50 microphones e BC202 100 Microphone control panel for 100 microphones Can be integrated at any point within the chains All BC202 s have their own ID number Copyright by Br hler ICS 33 DPS202 CDS200 II Troubleshooting Switching on the system produces The main cable connector is not Check if there is n
13. ati utente nas Sue A 19 5 2 4 1 UNIT NO AUTOMATIC mode 19 5 2 4 2 UNIT NO Semi AUTOMATIC Mode 20 5 2 0 System Se Up Charman savessa SARA A AAA 21 50 ME e gl taco rara sis 22 Sos 1xMIGROPHONE TEST see Ne 22 5 32 MIE EEDS ALL DON oder DEF sea see nn li 23 5 3 3 Information about Firmware Version 23 oA PG Remote Mode essen ernennen ee 24 524 1 Singe Central Control Un sera ek 24 5 4 2 Multiple Central Control Unssez nr RI RI Eee 25 60 ROUTING lA aM ae ae 26 SNOW ast E ET N 27 7 4 Technical Data DPSZ0 EE 28 7 5 Connector pinnings for service Ipformaton ccc cece cece cece cece eee eeeeeeeeeeeeenennanags 29 8 APDICatIONS csi aa ee ee ae an ee een ee en 31 ErOUDIESNOOLNG Zen nen Re des ei een 34 Warrants aaa aia ads 35 Service Tom see ee elle 37 Contact Informations ee see 39 Copyright by Br hler ICS 5 DPS202 CDS200 II 1 About this manual Symbols The following symbols and fonts are used in this manual N This sign indicates an important note which has to be followed to guarantee that the functions of the unit the security of any data or your health are not put at risk BA Indicates additional information remarks and tips FN Describes activities that must be performed in the shown order Words in bold letters require your special attention Copyright by Br hler ICS CDS200 II DPS202 2 Important remarks 2 1 For customers in the EU and in the USA Our equipment has been tested and complies with th
14. brahler CDS200 II Central Control Unit DPS202 Operating instructions Version 3 0 DPS202 Printed in Germany If you have questions about this manual please contact Brahler ICS Konferenztechnik International Congress Service AG P O Box 32 64 D 53627 K nigswinter Wahlfelder M hle 3 D 53639 K nigswinter T 49 0 2244 930 0 E sales braehler com You will find further information about our products on the internet at www braehler com 2007 BR HLER ICS AG K nigswinter CDS200 II All rights reserved especially also partly the translation reprint reproduction through copying or other similar methods BR HLER ICS reserves the right to make changes without notice INFRACOMO and DIGIMIC are registered trademarks Operating instructions CDS200 II DPS202 Sep 2009 Copyright by Br hler ICS CDS200 Il DPS202 DANGER OF ELECTRIC SHOCK DO NOT OPEN DEVICES Do not open housing with mains cable connected Maintenance operations may only be executed by qualified personnel Our equipment and installations have been built and tested according to the latest state of the art Under normal conditions they do not require any special maintenance However please be aware of the following Positioning secure and stable position of the equipment Ventilation operate equipment with proper ventilation Avoid heat sources such as heating radiators etc Mains connection pass all power
15. button 6 to scroll Figure 9 To enter the Test Routines press button 2 of Figure 25 Figure 25 Figure 26 Button 1 Here you can see the found and lost units see also Figure 5 and 6 like shown below Figure 27 5 3 1 MICROPHONE TEST Pressing the button 2 MICROPHONE TEST Figure 26 will cause the menu shown below Figure 28 Pressing the buttons 6 or 7 will set the starting number of the first unit t0 check Press ENTER 8 to accept this number and change to the input of the last unit to check Figure 29 Finish the input with ENTER 8 Figure 29 DO Copyright by Br hler ICS CDS200 Il DPS202 Figure 30 Start the test with button 2 START and also stop it with STOP 2 see below Figure 31 5 3 2 MIC LEDs ALL ON oder OFF Pressing button 3 MIC LEDs ALL ON will switch on and off all red light ring LED indicators of the units for a quick check Figure 32 aR Figure 33 5 3 3 Information about Firmware Version Figure 34 Pressing button 3 will display information about the version of firmware for Master MA and Slave SL controller See sample below e E E El 2 E Figure 35 After input of all necessary parameters the system is ready for use Because all values are saved setup is only reguired if changes have to be made 23 Copyright by Br hler ICS DPS202 CDS200 Il 5 4 PC Remote Mode Ss 5 a 4 a Figure 36 The DPS202 is either able to wor
16. cables so that they will not be damaged M M M M Cable connections avoid trip traps VI Liquids avoid penetration of liquids into the housing M Power sockets operate equipment only with power sockets that are connected to ground according to the relevant specifications and regulations Warning Never expose equipment to rain or humidity Rough handling of the equipment such as strong shocks or vibrations may result in damages Inappropriate handling and storage which does not conform to the operating instructions may also lead to equipment damages Copyright by Br hler ICS 3 DPS202 CDS200 II A Copyright by Br hler ICS CDS200 II DPS202 Content TV ADOUT this MANU AN net 6 DIT OIS oe setae A a ee 6 2 1MDOH ANNE ema a 7 3 Short description Central Control Unit DPS202 ENEE 9 2 ee ue e 11 Aal Mans DoWer connecler aa 11 4 2 Audio AF EINK connector SSG ee ee A 11 4S EXT LSIN connector ALBA a En Re 11 4 4 MIXER PA l ne out connector A EE 12 4 5 UNITS 1 4 line connector SO Diner a a 12 4 60 POIN AG Oo IRD UT i arr Eare eroris 12 AT PO LINK ACASO UPA a E a ee ee 12 AS Connecting to WE Lg d NEE 13 o Te GE 14 ds S tarta et ee reed 14 Sade le Status Ee 14 DZ STAND ALONE Mode eu aan 16 921 NUC ModeS iaa ae 17 5 2 2 MIC ROUTING Microphone Routing cccce eee ccee cece cece eeseaeeeeeeeeeessaaseeeeeeeeeeaaas 18 9 29 Lo 1loudspeakern ROUNO saute an idea 18 DAA System SEL ce gre eect cian ero a
17. d to OUT1 one total signal DPS ID is 01 a MIC microphone Routing Figure 4 In default setting all signals are routed to output XLR OUT 1 Pressing button 5 will show the next menu Figure 5 DPS202 b UNITS ONLINE This display shows the total number of units 37 of 38 units have been found in the sample This menu will always stay once selected It can be changed to another menu with button 5 S al ai a a Figure 5 Copyright by Br hler ICS DPS202 CDS200 Il c FOUND LOST You can check the units of each line by pressing CHECK button 7 IZ Figure 6 Sample L1 no units found no units lost L2 2 units found no units lost L3 13 units found 1 lost for instance in the case of removal by pressing button 3 the number of the lost unit will be displayed L4 22 units found no units lost Note if more than one unit is lost then repeatedly pressing of the corresponding button will display all numbers one after the other Pressing key 5 OK of Figure 6 will cause the return to main menu E E Bea 2000 Figure 7 5 2 STAND ALONE mode With pressing SET button 6 Figure 7 configuration setup is shown Er E EN E SE Figure 8 First the operation mode STAND ALONE or PC REMOTE has to be selected The current adjustment is shown by the black cursor besides the buttons 1 and 2 In the sample above STAND ALONE is the active mode In the case of controlling by the DPS2
18. e requirement of the CE test This guarantees the protection against harmful interferences when the equipment is operating in a commercial environment If the unit is not proper installed to this user manual it may causes radio interferences Any changes or modifications not explicit approved in this manual could void your authority to operate this equipment The equipment must be connected to earth 2 2 Safety Check that the operating voltage of the unit is identical with the voltage of your local power supply If a voltage conversion is required consult your BRAHLER ICS dealer or qualified personnel Should any liquid or solid object fall into the housing unplug the unit and let it check by qualified personnel before further operation Unplug the unit from the power outlet or set the main power switch to OFF if it s not used for several days To disconnect the cord pull it out holding the plug Never pull the cord itself 2 3 Installation Allow proper air circulation to prevent internal heat built up Do not place the unit on a surface that may block the ventilation holes Do not install the unit in a location near heat sources or in a place exposed to direct sunlight excessive dust humidity mechanical vibration or shock To avoid condensation do not install the unit where the temperature may increase rapidly 2 4 Cleaning To keep the housing in its original condition periodically clean it with a soft cloth Stubborn stains ma
19. fault settings Please note If it is not ensured that all delegate units have different ID s over all four lines it is absolutely necessary to start number programming For applications of more than one DPS in PC remote mode see gt Chapter 8 5 1 Starting Setup Note All settings and adjustments will be stored and saved if the Central Control Unit is switched to OFF and ON again After switching on the system you will see the welcome menu for about 6 seconds E al ERRET 2 Figure 1 5 1 1 Status displays After 6 seconds or by pressing any button the display can be switch to the main menu shown below Note The menu will also be displayed after 60 seconds if no setup procedure SET is done Ze al i 7 m 0 Figure 2 The main menu shows the active operation modes When starting the DPS the very first time the default values are displayed Up to now all changes are saved and loaded with the next starting of the DPS 14 Copyright by Br hler ICS CDS200 Il By pressing button 1 and 8 simultaneously the default values are loaded ef al a sf 2 e Figure 3 A request will follow whether the default values are overriding the current values With button 5 OK the default values are loaded With button 8 NO you may cancel the default settings The default values are AUT3 NEXT in STAND ALONE mode No chairman assigned no VIP assigned LS INTERN routing LS level 60dB All microphones route
20. k in stand alone mode or in connection with a PC In connection with MicControl software and a PC there are manifold options for system parameters and operation modes 5 4 1 Single Central Control Unit The remote mode requires only the following settings e Microphone signal routing e LS loudspeaker signal routing Please see the description in the corresponding chapters for Stand Alone mode 5 2 2 and 5 2 3 RE 5 3 l Figure 37 e ID numbering about System Setup e Setting of Baud Rate Figure 38 All other adjustments are PC controlled The Remote Mode additional offers further microphone mode Furthermore a speaking time limit for the delegates is provided see Manual for MicControl Copyright by Br hler ICS 24 CDS200 Il DPS202 Selecting the System Setup leads to the following menu DPS ID is only relevant if using more than one DPS in the system See next chapter EA ee a NN EJ Figure 39 Set BAUD RATE with pressing button 4 ISL Jet Fr Je Figure 40 The baud rate is set in accordance with your equipment Possible baud rates are 19 200 38 400 or 57 600 Just press the corresponding button 1 2 or 3 and confirm your setting 5 4 2 Multiple Central Control Units BA Each DPS unit within a system with multiple DPS units must have a unique ID number Double allocation will cause an error Using more than one Central Control Unit DPS202 is only possible in PC REMOTE mode Next ste
21. lines are also routed to LINK AF LINK OUT connector Figure 12 Nevertheless the lines L2 to L4 may be routed individually to the corresponding outputs like shown in Figure 13 This is done by pressing the buttons 2 3 or 4 er E S ETETE Figure 12 Sf I fe 5 Figure 13 Output 2 L2 may be routed either to Output 1 sum or to Output 2 separately button 2 Output 3 L3 may be routed either to Output 1 Sum or to Output 3 separately button 3 Output 4 L4 may be routed either to Output 1 sum or to Output 4 separately button 4 5 2 3 LS loudspeaker Routing Button 3 Figure 9 a 2 EH Aa ES A GJ Figure 14 In this menu LS ROUTING can be set to INTERN button 2 EXTERN button 3 or LINK button 4 by pressing the corresponding button 48 TTA Copyright by Br hleries CDS200 Il DPS202 Selection INTERN means that LS signals are controlled by the DPS202 In this case of internal processing the level of the LS signal can be adjusted after pressing button 6 LEVEL In the following menu Figure 15 you can adjust the level with button 6 decrease and button 7 increase in a range from 62dB to OdB To avoid feedback the starting level is set to 60dB er m gt HI Se Figure 15 Selection EXTERN means LS signals are fed in via LS XLR connector at the rear of DPS In this case the level of the input signal is controlled externally e g via mixer LINK For the operatio
22. n with several DPS units there is provided the routing of the LS signals to one Central Control Unit DPS202 Thus the complete decentralized sound can be guaranteed by the loudspeakers in all delegate units 5 2 4 System Setup First press button 6 to scroll Figure 9 E Aa EA J 2 Figure 16 Pressing the button 1 leads to SYSTEM SETUP like shown below SE E EH EI eS Figure 17 Within the menu SYSTEM SETUP additional settings are possible 5 2 4 1 UNIT NO AUTOMATIC mode UNIT NO button 2 will call the two possibilities for programming the delegates units AUTOMATIC button 2 and SEMI AUTOMATIC button 3 mode Copyright by Br hler ICS 19 DPS202 CDS200 Il Figure 18 Pressing button 2 will lead to full automatic mode for programming the connected delegates units Figure 19 Start the programming procedure with button 6 START Figure 19 Line L1 to L4 will be checked successive for connected microphone units The total numbers of units per line are displayed Just wait until all lines are checked Meanwhile an arrow besides the line number L1 to L4 showing the momentary line to be check Procedure stops self acting If you want to terminate programming immediately press again button 6 STOP Figure 20 In this case a power reset is necessary Otherwise pressing OK button 5 will lead to System Setup Figure 17 5 2 4 2 UNIT NO Semi AUTOMATIC Mode Button 3 Figure 1
23. o connection to the no POWER ON condition green light properly connected to the mains power does not light up corresponding socket of the unit Connection cable possibly defective Replace a new mains cable The power switch is not in the correct Turn on the POWER ON switch position One or some of the yellow LEDs do Probably there is no audio signal no Check whether the speaker s not light up speaker active microphone is active ring shaped indicator Check the cabling of the units and the microphones One or some of the green LEDs do One or more delegate units cause a Check the corresponding line for any not light up L1 L4 short circuit failure in the cabling One or more lines are out of order Check the units Remove or replace the defective unit out of the line Do not switch on and off the DPS trying to remove the short circuit Also do not plug and unplug the connector of the faulty line DPS unit does not work correctly Communication failure Check correct operation modes after connecting to the system Stand alone or Remote Mode Controlling and correction of the setup menu Pay attention to the UNIT ID The same unit No will cause an error Activation of one microphone unit Double ID numbers in the system Renumbering of the corresponding switches on an additional unit unit see semi automatic numbering figure 18 System performance low Double ID numbers in the system Renumbering of
24. ot compatible to the improved CDS200 II system BB Copyright by Br hler ICS CDS200 II DPS202 3 Short description Central Control Unit DPS202 Congratulations on buying the DPS202 from BR HLER ICS Thank you for the confidence you have given us The Central Control Unit DPS202 belongs to the family of the Congress Data Systems CDS CDS200 Il is the evolution of the successful Congress Data Systems CDS200 From the stand alone application of simple discussion equipment to a complete system solution for modern conference management with CDS200 II everything is possible 205200 I DPS202 Leed dood LE L LY LA Li L2 L3 LA Front View As part of the Congress Data System CDS200 ll the Central Control Unit DPS202 is used for controlling of up to 160 system units These units are delegates units with voting facility system control consoles for controlling the microphone and voting operation modes as well as interfaces for the connection of large screen displays The DPS202 is either able to work in stand alone mode or in connection with a PC In the case of stand alone mode there are 8 buttons to control the unit via a clearly arranged LC Display In connection with MicControl software and a PC there are manifold options for system parameters and operation modes The microphone signals at the UNITS inputs 1 to 4 may be either routed individually to the corresponding outputs 1 to 4 or all together mixed to output OUT 1 all In
25. p is to check the IDs of each unit They must be different Select the system setup and herein the DPS ID setting with button 1 Figure 41 Figure 42 Select ID numbers for all DPS in your system They must be different All other settings are described in the chapters for Single unit and or Stand Alone mode Note The numbers of the delegate units must be different only within a range of one DPS ID A sample for cabling more than one DPS is shown in chapter 8 Applications Copyright by Brahler ICS 25 DPS202 6 Routing diagram The following diagram shows the complete routings of the LS and AF to LINE OUT L1 to L4 XLR UNITS bh SE Oo 009 El aj Je aj Je y AM LA 000 O P 000 00 oo 099 Oo a O MIC LINK IN AF LINK IN LS LINK Digital volume control LSA B EXT LS_IN Figure 43 26 CDS200 II le OUTI all J le OUT2 le OUT3 J le OUT4 MIC LINK OUT AF LINK OUT LS LINK RL relay Copyright by Br hler ICS CDS200 II DPS202 7 Short Overview Status and CDS 200 II DPS202 TT a U OON ua L LJ orog LL iol U eltolfo llo S Sel A AF 48VDC ae O O Gi O O O O 0000 0 REMOTE L1 2 3 L4 L1 L2 13 L4 Figure
26. tion 320VA max Housing e 19 2 HU Aluminium silver anodized e Fan cooling e WxHxD 433 x 88 x 305 mm Weight e 4 5kg Optional not included in delivery e System software MicControl e Connection cable to PC 08 2140 Version RS232 op Copyright by Br hler ICS CDS200 II 7 2 Connector pinnings for service information UNITS S8G GJ female connector view front view Cable 13 6190 AF LINK S8G GK IN OUT connector female connector view front part blu GND Shield LSLINK A MICLIN B MICLOUT B MICLIN A MICLOUT A MIXER PA and EXT LS IN X3 CS OUT1 all OUT2 OUT3 OUT4 XLR connector Output male connector view Input female connector view PA LINE balanced AT ARA HEN AB NEB DPS202 Copyright by Br hler ICS 29 DPS202 CDS200 II PC IN C15 CR data connector DATA A GND Digital INPUT OUTPUT BO Copyright by Br hler ICS CDS200 II DPS202 8 Applications In the following you see some examples in form of block diagrams d DPS202 a Cm Cuun gt ___ amp TM58 Delegate Units DC10 and EDC10 EDC10 Application 1 This diagram shows an application for a simple discussion system The DPS works in STAND ALONE mode When done the system setup there is no further control necessary CDS200 II System Components e DPS202 Central Control Unit with 4 line outputs e DC10 Delegate unit with MIC function e EDC10 Built
27. y be removed with a cloth lightly dampened with a mild detergent solution Never use organic solvents such as thinners or abrasive cleaners since these will damage the cabinet 2 5 Repacking Save the original shipping carton and packing material they will become useful if you ever have to ship the unit In this case please keep the manual together with the unit For maximum protection re pack the unit as originally packed from the factory If not supplied with the equipment a complete transportation and storage box system is available from BRAHLER ICS We recommend using this system for long term protection and care Copyright by Br hler ICS 7 DPS202 CDS200 II General Please keep this manual together with the CDS200 II Power Supply DPS202 If you hand on the units to third parties please include this manual Please read the manual carefully taking special care when you see this symbol as it indicates N important information C This product is conforming to the rules of the following European directive 89 336 EWG Council directive to the alignment of the rules of rights of all member states about the electromagnetic compatibility modified through RL 91 263 EWG 92 31 EWG and 93 68 EWG of the council Further information is available on request BA The warranty will expire if you cause defectives through inappropriate use or handling of the unit Former CDS200 system components e g DV200 DVA200 EDV200 etc are n
Download Pdf Manuals
Related Search