Home

T12VFL 12V Li-ion Torch Light

image

Contents

1. 12V Li ion Torch Light TI2VEFL User Manual Please read and retain for future reference IMPORTANT Read all instructions before use Contents Parts List Technical Information Safety Instructions Using your light Maintenance Warranty Parts List No eseription Pa p oreo Ce switch button 8 Switch button hoier o Host connector holder Exploded Assembly Diagram NOTICE Actual product may vary from pictures shown h TERRATEK Y 1 LED bulbs 2 Switch Button 3 Battery Pack 4 Charger Battery capacity indicator LED Charge indicator fig 2 Technical Information Model T12VFL Rated Voltage 12V DC Bulb type LED Battery Type 1300 mAh Li ion Charger Charging time 1 hour Input 100 240V AC 50 60 Hz 27W Output 12 6V DC 1500mA Max Read this entire manual before using this product Failure to do so can result in serious injury Save this manual for future reference Copyright 2013 by ACL Group Intl Ltd All rights reserved This manual or any artwork contained herein must not be reproduced in any shape or form without the express written consent of ACL Group Intl Ltd Diagrams within this manual may not be drawn proportionally Due to continuing improvements actual product may differ slightly from the product described herein Read and Keep This Manual Please read carefully all instructions within this manual Failure to follow all safety warning
2. J NEVER use an engine generator or DC power to charge K NEVER store the battery or battery charger in places where the temperature may reach or exceed 104 F 40 C L ALWAYS operate charger on standard household electrical power 230 volts Using the charger on any other voltage may overheat and damage the charger M ALWAYS wait at least 15 minutes between charges to avoid overheating the charger N ALWAYS disconnect the power cord from its receptacle when the charger is not in use ADDITIONAL PRECAUTIONS FOR CHARGER amp BATTERY PACK 1 Do not charge battery pack when temperature is below 10 C 50 F or above 40 C 104 F 2 Do not attempt to use a step up transformer an engine generator or DC power receptacle 3 Do not allow anything to cover or clog the charger vents 4 Always protect the battery terminals when the battery pack is not used 5 Do not short the battery pack 6 Do not touch the terminals with any conductive material 7 Avoid storing battery cartridge in a container with other metal objects such as nails coins etc 8 Do not expose battery pack to water or rain Warning A battery short can cause a large current flow overheating possible burns and even a breakdown 9 Do not store the tool and Battery pack in locations where the temperature may reach or exceed 50 C 122 F 10 10 Do not incinerate the Battery pack even if it is severely damaged or is completely worn out The battery pack c
3. Battery packs batteries Li lon Li lon ys Do not dispose of battery packs batteries into household waste water Li lon or fire Battery Ji packs batteries must be collected recycled or disposed of in an gt By environmentally friendly way MAX 50 C Only for EC countries Defective or dead batteries must be recycled according to the directive 2006 66 EC Maintenance Use only a dry soft cloth for wiping the unit Do not use a damp cloth thinner or other volatile solvents for cleaning 13 Accessories CAUTION Use only accessories or attachments recommended for use with your Terratek tool specified in this manual The use of any other accessories or attachments might present a risk of injury to persons Only use accessory or attachment for its stated purpose Declaration of Conformity We ACL Group Intl Ltd England DN6 8LZ declare that the torch light has been manufactured according to our full quality assurance procedures The declaration is to certify that it conforms to CE EMC LVD and RoHS directives EN55015 A2 2009 EN60547 2009 All provisions of Annex 1 of Council Directive 2004 108 EC EMC directive EN60598 1 A11 2019 EN60589 2 4 1997 EN62471 2008 All provisions of Annex 1 of Council Directive 2006 95 EC Low Voltage Directive RoHs 2011 65 EU Mr Alan Garnett UK QA Manager 14 Environmental Protection RECYCLING WASTE ELECTRICAL PRODUCTS SHOULD NOT BE DISPOSED OF WITH HOUSE
4. off the tool and switch on again to resume the work make sure to apply only suitable workload to the tool When the tool works under heavy load for a long period of time the temperature of the tool or battery pack will increase significantly The protection device will be activated at a preset temperature to protect both the tool and the battery If this occurs switch off the tool and wait until it cools down to ambient temperature and resume work Note when the voltage of battery pack is dropped to 7 5V the protection device will also be activated In this case remove the battery pack and fully charge it before reuse WARNING I mproper use of the battery or battery charger can lead to serious injury To avoid these injuries A NEVER disassemble the battery B NEVER incinerate the battery even if it is damaged or is completely worn out The battery can explode in a fire C NEVER short circuit the battery D NEVER insert any objects into the battery charger s air vents Electric shock or damage to the battery charger may result E NEVER charge outdoors Keep the battery away from direct sunlight and use only where there is low humidity and good ventilation F NEVER charge when the temperature is below 32 F 0 C or above 104 F 40 C G NEVER connect two battery chargers together H NEVER insert foreign objects into the hole for the battery or the battery charger NEVER use a booster transformer when charging
5. HOLD WASTE PLEASE RECYCLE WHERE FACILITIES EXIST CHECK WITH YOUR LOCAL AUTHORITY OR RETAILER FOR RECYCLING ADVICE Hh Please read the following carefully ACL Group Intl Ltd and or it s distributor has provided the parts list and assembly diagram as a reference tool only Neither ACL Group Intl Ltd or its distributor makes any representation or warranty of any kind to the buyer that he or she is qualified to do any repairs or replace any parts of this product ACL Group Intl Ltd and its distributor expressly State that all repairs or parts replacement should be done by certified or licensed technicians The buyer assumes all risk and liability arising out of his or her repairs or parts replacement to the original product 12 Months Limited Warranty If within 12 months from the date of purchase you experience any problems with your product please return the product to its distributor dealer for repair or replacement This warranty DOES NOT COVER normal wear or any damage as a result of accidents misuse abuse or negligence ACL Group Intl Ltd Doncaster England Email info terratekintl com www terratekintl com 15
6. an explode in a fire 11 Be careful not to drop shake or strike battery 12 Do not charge inside a box or container of any kind The battery must be placed ina ventilated area during charging Unpacking Carefully remove the product and any accessories from the box Make sure that all items listed in the packing list are included Package contents A 12V torch light B 1 hour fast Charger C User manual Functional Description Fig 1 WARNING Remove battery pack before making any assembly adjustments or changing accessories Such preventive safety measures reduce the risk of starting the tool accidentally Installing or removing battery pack 1 To remove the battery pack withdraw it from the tool while depressing the tabs Fig 2 on both sides of the battery pack 2 To insert the battery pack align the ribs on the top of the battery with the grooves in the housing and slide it into place Always insert it all the way until it locks in place with a little click Lightly pull on the battery pack to ensure it is locked into place and will not accidentally fall out of the tool causing an injury 3 Do not use force when inserting the battery pack If the battery does not slide in easily it is not being inserted correctly 11 Operation Switching On and Off 1 To turn on the torch light depress the switch button Fig 1 2 2 Turn off depress the switch button again Note when the voltage of battery pack is dr
7. ance with metal surfaces Do not expose your power tool to wet or damp conditions and NEVER use in rain Check regularly the power cord of your machine and any extension cord that you are using for damage Do not carry or pull the machine with the power cord Ensure the cord is clear from hot surfaces oil or sharp objects Safety rules for battery worklights Under extreme usage or temperature conditions battery leakage may occur f liquid comes in contact with your skin wash immediately with soap and water If liquid gets in your eyes flush them with clean water for at least 10 minutes then seek immediate medical attention Batteries can explode in the presence of a source of ignition such as a pilot light To reduce the risk of serious personal injury never use any cordless product in the presence of open flame An exploded battery can propel debris and chemicals and cause serious injuries Do not crush drop or damage battery pack Do not use a battery pack or charger that has been dropped or received a sharp blow A damaged battery is subject to explosion Properly dispose of a damaged battery immediately Failure to heed this warning can result in serious personal injury Read all the instructions before using the worklight To reduce the risk of injury close supervision is necessary when used near children Do not use outdoors To reduce the risk of electrical shock do not put flashlight or charger in water or other li
8. injury never allow the worklight lens to come in contact with anything Keep light dry clean and free from oil and grease Always use a clean cloth when cleaning Never use petroleum based products or any strong solvent to clean the worklight Don t expose worklight to rain Water entering a power tool will increase the risk of electric shock or malfunction Do not overreach Keep proper footing and balance at all times Do not use on a ladder or unstable surfaces Symbols IMPORTANT Some of the following symbols may be used on your tool Nebascacenacitamnceacel OILS non ai AMpPeres Zico titcmteemnadese ONL etnewteroreeeee en Alternating current LAM aeaenenenensss revolutions per minute 2 ee class II construction double insulated KO nananana emeena a a KIlOgra ms Niessen NO Oad Speed C E ococususususensseeConforms to European Harmonised New Approach Directives DC aseeaeeenenee Direct Current Worklight use and care This product is for household use only Store worklight out of the reach of children and other unqualified persons Worklights are dangerous in the hands of untrained users Let the worklight cool for several minutes before changing the bulb Do not use or permit use of worklight in bed or sleeping bags This worklight lens can melt fabric and a burn injury could result Battery use and care A battery operated tool with integral batteries or a separate battery pack must be recharged only with
9. opped to 7 5V the protection device built in the tool will be activated In this case remove the battery pack and fully charge it before reuse LED Capacity indicator Fig 2 All three LED s are on gt 90 Two LED s are on gt 60 One LED is on lt 30 Once only the one LED is lit the battery must be re charged Changing the light bulb 1 Remove the lens cover by rotating the cover counter clockwise 2 Gently pull out the burned bulb and replace with a new one 3 Replace the lens cover 12 Disposal of the exhausted battery WARNING Do not dispose of the exhausted battery The battery must explode if it is incinerated The product that you have purchased contains a rechargeable battery The battery is recyclable At the end of its useful life under various state and local laws it may be illegal to dispose of this battery into the municipal waste stream Check with your local solid waste officials for details in your area for recycling options or proper disposal Disposal Power tools accessories and packaging should be sorted for environmentally friendly recycling Only for EC countries Do not dispose of power tools into household waste According to the European Directive 2002 96 EC on waste electrical and electronic equipment and its incorporation into national right products that are no longer suitable for use must beseparately collected and sent a for recovery in an environmentally friendly manner
10. quid Do not place or store appliance where it can fall or be pulled into a tub or sink Use only the charger supplied by the manufacturer to recharge Use only recommended battery pack Using another battery pack will cause damage to your worklight and could possibly explode cause a fire or personal injury For use with 12v Li ion batteries Remove battery pack from worklight before replacing bulb or performing any maintenance or cleaning Replace bulb with same type LED Do not disassemble the worklight Do not place worklight or battery pack near fire or heat They may explode Do not dispose of a worn out battery pack by incinerating Do not incinerate the battery The battery may explode in fire Do not operate worklight or charger near flammable liquids or in gaseous or explosive atmospheres nternal sparks may ignite fumes Do not store your worklight in a damp or wet location Do not store in locations where the temperature is less than below 10 C 50 F or above 40 C 104 F Do not store in outside sheds or in vehicles Do not permit children to use worklight unsupervised It is not a toy The temperature of the bulb will become hot after being on for only a short period of time This hot temperature can cause burn injury if touched and can create sufficient heat to melt some fabrics If wrapped or comes in contact with fabrics the worklight lens can produce sufficient heat to melt some fabrics To avoid serious personal
11. s can result in serious personal injury The term Power Tool in all of the following warnings refers to your mains operated corded or battery operated cordless power tool Important SAFETY Information This symbol is to warn you of potential personal injury hazards Please read carefully the notes along side this warning to avoid possible injury or death General Safety Rules WARNING Read all instructions Failure to follow all instructions listed below may result in electric shock fire and or serious injury The term power tool in all of the warnings listed refers to corded or cordless power tools Work area safety Keep work area clean and well lit Cluttered or dark areas invite accidents Do not operate power tools in explosive atmospheres such as in the presence of flammable liquids gases or dust Power tools create sparks which may ignite the dust or fumes Keep children and bystanders away while operating a power tool Distractions can cause you to lose control Electrical safety Before use ensure that the power outlet you are using matches the plug on your power tool and that the voltage of the outlet matches that of your power tool Only use grounded extension cords with power tools fitted with 3 pin plugs and if using outdoors ensure any extension cord is suitable for outdoor use Always try to avoid body contact with grounded surfaces such as radiators cooking ranges and any other fixed appli
12. the specified charger for the battery A charger that may be suitable for one type of battery may create a risk of fire when used with another battery Use battery operated tool only with specifically designed battery pack Use of any other batteries may create a risk of fire Hold the tool by its handle only Because the tool operates by battery power be aware of the fact that it can begin to operate at any time Charging the battery pack Fig 2 Note Newly purchased Batteries are not fully charged and must be charged before using in your cordless tool s 1 Plug the battery charger into the proper AC voltage source 2 Insert the battery pack so that the ribs on the battery pack slide into the grooves on the battery charger Insert the cartridge fully into the charger Fig 2 3 When the battery pack is inserted the Red LED will light indicating the charger has started the charging cycle A Green light will indicate the battery is completely charged and should be removed from the charger Fig 2 4 After charging unplug the charger from the power source 5 Other tips for extending Battery life Do not store batteries completely discharged Charge them fully before storing Overload Protection The power cutter is fitted with an overload overheat protection device When the tool is forced to work at an excessive load the protection device will be activated automatically to disconnect the power supply If this occurs switch

Download Pdf Manuals

image

Related Search

Related Contents

TTM 60-61 Service Manual  "取扱説明書"  Samsung BT65CDPHXR Инструкция по использованию  Magnese MA-204026W    klimanaut indoor 400 wrg 3.76  Spec Sheet: TSW-1052  Midas DL252 User's Manual  Linksys LGS528-EU network switch  Manual Usuario - Powertec Outboards  

Copyright © All rights reserved.
Failed to retrieve file