Home
Because you`re not like everybody else. EVAPORATIVE COOLER
Contents
1.
2. 5 Product Benefits 5 Parts List 5 Parts Diagram 6 Operating Instructions 7 Set Up 7 Filling the Water Tank 7 Using the Ice Pack 8 The Control amp Display Panels 8 Using the Remote Control 11 Maintenance 11 Exterior Cleaning 12 Dust Filter amp Cooling Pad Cleaning 12 Water Tank Cleaning
3. 13 Water Pump Maintenance 13 Technical Support 14 Product Specifications 14 Troubleshooting 15 Warranty 16 SAVE THESE INSTRUCTIONS Please carefully read this manual before attempting to use this evaporative cooler For your own safety comply with all safety instructions and warnings contained in this owner s manual to prevent personal injury or property damage 4 www LumaComfort com IMPORTANT SAFETY INFORMATION These instructions are not meant to cover every possible condition and situation that may occur Please read all instructions before using this evaporative cooler Failure to carefully read all instructions may result in possible electric shock or fire hazard and will void the manufacturer s warranty 1 Use this evaporative cooler only as instructed in this owner s manual Other uses may cause electric shock injury or fire 2 Close supervision is required if this cooler is used near children or pets 3 To protect against electric shock do not immerse this cooler or its plug
4. and cord in water 4 If the cooler is being transported or will not be in use disconnect it from the power supply by tightly gripping the plug and pulling it from the power outlet Do not disconnect the power supply by pulling on the evaporative cooler s power cord 5 Avoid contact with any of the evaporative cooler s moving parts 6 Place the evaporative cooler on a level surface 7 This evaporative cooler is intended to fit into a matching receptacle Under no circumstances should the plug be altered in any way An improper connection can result in electric shock 8 If possible avoid using extension cords with this evaporative cooler If an extension cord is absolutely necessary do not use more than one extension cord to operate more than one cooler 9 Do not insert objects or allow fingers to enter into the cooler s grills as this may cause electric shock or bodily injury Do not block or tamper with the evaporative cooler while it is in operation 10 Do not run the power cord under mats or carpeting and do not cover the power cord with runners Arrange the power cord away from room traffic and where it can be tripped over 11 Do not operate this evaporative cooler in the presence of flammable substances or explosives 12 Do not place the cooler near an open flame or cooking heating appliances 13 If the evaporative cooler will not be in use empty the tank of any remaining water 14 If the cooler
5. Because you re not like everybody else EVAPORATIVE COOLER EC45S OWNER S MANUAL 2 www LumaComfort com BECAUSE YOU RE NOT LIKE EVERYONE ELSE And neither are we Always at the forefront of our industry our goal is to offer the best quality product and consumer value on the market Our team is constantly pushing the boundaries of innovation and design to create exceptional products to help you achieve a more comfortable living or work space Our goal is to ensure that every Luma Comfort customer is 100 satisfied with their product If you have any questions or concerns regarding your product or if you would simply like to share an idea with us please feel free to contact us Our friendly and knowledgeable customer support team is here for you Call us today at 866 737 6390 or email support lumacomfort com For future reference we recommend you attach a copy of your sales receipt here and record the following information You will need this information if it becomes necessary to contact the manufacturer for service inquiries Date of Purchase ___________________________________ Serial Number ___________________________________ Model Number ___________________________________ Connect with us online 3 Say Goodbye to Ugly Products CONTENTS Important Safety Information 4 Get To Know Your Evaporative Cooler
6. COOLING PAD CLEANING To prevent the cooling pad and filter from becoming clogged with dust mineral deposits and other buildup we recommend that it be cleaned at least once a month 1 Remove the dust filter from the back of the unit by pushing down on the two tabs located above the filter and pulling it out Gently scrub it with a soft brush and rinse with water 2 While the dust filter is off remove the cooling pad frame from the back of the unit Rinse the pad with clean water to remove dust For a more thorough cleaning use a diluted vinegar solution to wash the pad If necessary immerse the pad in the diluted vinegar solution for 30 seconds to remove hard water buildup Be sure to rinse the pad thoroughly with clear water to remove vinegar residue 3 Allow the filter and the cooling pad to air dry completely before replacing them in the unit 13 Say Goodbye to Ugly Products WATER TANK CLEANING The water tank should be emptied regularly to ensure hygienic use To empty the tank 1 Unlock and pull open the water tank 2 Place a small dish beneath the extended water tank 3 Remove the white plug from the bottom of the water tank to allow water to drain out into the dish 4 When empty replace the plug in the drain Be sure it is secure to avoid leaking In addition the tank should be cleaned several times a year to remove hard water and mineral deposits Use a soft damp cloth to wipe out the in
7. ay Goodbye to Ugly Products OPERATING INSTRUCTIONS SET UP Carefully remove all packaging materials and retain for future storage use Make sure there is no residual foam left in any of the components No tools will be required to assemble this evaporative cooler Place the cooler on a firm level surface before proceeding Before using the evaporative cooler for the first time we recommend cleaning the tank with a solution of warm water and light detergent FILLING THE WATER TANK 1 Locate the water tank knob and turn it counterclockwise 90 to unlock the tank Pull out the water tank from the back of the cooler 2 Fill the tank with clean water Pay attention to the water level indicator located on the front of the cooler to avoid overfilling the evaporative cooler Do not fill the tank above the MAX water level line or below the MIN water level line The approximate tank size of the EC45S is 1 6 gallons 6 liters 3 Push the water tank back into the rear of the unit and turn the water tank knob clockwise 90 to lock the water tank back into place 8 www LumaComfort com USING THE ICE PACK The Luma Comfort EC45S tower evaporative cooler includes an optional ice pack for added cooling 1 Place the ice pack in the freezer until frozen Do not open the ice pack or ingest its contents 2 Open the water tank and put the ice pack into one of the water tank s chambers 3 The ice pack is not necessary for
8. e control and turn it as directed on the remote control 2 To use the remote control aim it at the unit s remote control receiver and select one of the functions on the remote control The effective distance is approximately 24 ON SPEED Turns the power on and adjusts the fan speed OFF Turns the power off TIMER Activates timer function of up to 7 5 hours SWING Activates oscillating air louvers COOLER HUMIDIFIER Activates cooling humidification function MODE Adjusts the airflow mode MAINTENANCE Always unplug the evaporative cooler from the power supply before servicing or cleaning Regular cleaning and maintenance is an essential step in maintaining the longevity of your tower evaporative cooler and ensuring that it operates free of defects Maintain your evaporative cooler by following the steps on the following pages If the evaporative cooler will not be in use for an extended period of time place the unit back in its original carton and keep it stored in a clean dry place 12 www LumaComfort com EXTERIOR CLEANING 1 Use a soft cloth and a mild soap and warm water solution to clean the unit s exterior Do not use harsh cleaners gasoline paint thinner benzene etc as these substances can damage the evaporative cooler 2 Thoroughly dry all of the cooler s parts with a soft cloth before reconnecting the unit to the power supply DUST FILTER amp
9. eight 12 8 pounds Voltage 110V 120V Wattage 45W Coverage Area Up to 100 sq ft Tank Size 1 6 gallons Fan Speeds 3 Noise Level dB 64 Airflow 250 CFM Oscillation Yes Warranty 1 year manufacturer s warranty 15 Say Goodbye to Ugly Products TROUBLESHOOTING Problem Possible Cause s Possible Solution There is no airflow a The power cord is not plugged in b The water tank is not locked into the unit a Check to make sure the plug is plugged into an outlet The unit should beep twice once the power supply is connected b Make sure the water tank is locked into the back of the unit The unit does not cool at all a There is insufficient water in the tank b The cooler humidifier button was not pressed c The pump is defective a Check the water level in the tank and make sure there is enough water b Press the COOLER HUMIDIFIER button c Contact customer service if there is an issue with the water pump The unit does not sufficiently cool The cooling pad is not sufficiently saturated with water Wait a few minutes for the cooling pad to be fully saturated with water Water is coming out of the vents The cooling pad may be clogged with debris Clean the cooling pad by rinsing it in water and allowing it to thoroughly dry If the problem persists contact customer service 16
10. operation but will help enhance the cooling effect in higher temperatures 4 The ice pack will last approximately 4 hours before melting THE CONTROL amp DISPLAY PANELS 9 Say Goodbye to Ugly Products After the tank is filled with water connect the evaporative cooler to a power outlet The unit will beep twice indicating that the power source is connected The cooler will be in standby mode at this time ON SPEED amp OFF Buttons Press the ON SPEED button to turn on the evaporative cooler To adjust the fan speed press ON SPEED button again until your desired speed has been reached The current fan speed will be indicated on the display panel To turn the unit off and revert back to standby mode press the OFF button Fan Speed Indicators LOW MEDIUM HIGH COOL HUMIDIFIER Button Cooler Humidifier Indicator After the desired fan speed has been selected press the COOLER HUMIDIFIER button to activate the cooling humidifying function This powers the water pump cools the air and adds moisture to your air at the same time The blue cooling icon will also be visible on the display panel MODE Button The EC110S has 3 different automatic airflow modes Setting the airflow mode is optional Manual Mode Manual Mode Indicated by the three circular icons on the display panel this allows you to set the fan speeds manually 10 www LumaComfort com Natural Mode Natural Mode Indica
11. s plug or power cord is damaged do not attempt to repair the components yourself Please contact Luma Comfort s customer service hotline at 1 866 737 6390 or have the unit examined by an authorized service provider 5 Say Goodbye to Ugly Products GET TO KNOW YOUR EVAPORATIVE COOLER PRODUCT BENEFITS Designed to cool smaller areas such as single rooms office cubicles and personal spaces Sleek modern design makes it an attractive addition to your home Tower body shape saves space High efficiency rigid cooling pad holds more water Powerful motor results in more powerful airflow faster evaporation and cooler air Consumes as much electricity as your typical 45 watt light bulb Eco friendly evaporative cooling system cools the air by the natural process of evaporating water with no Freon or harmful chemicals Adds moisture to dry environments and eliminates airborne dust particles PARTS LIST Check to ensure the following parts are included with your product Evaporative cooler Ice Pack Remote control CR2032 3V battery 6 www LumaComfort com PARTS DIAGRAM 1 Control panel 2 Display panel 3 Remote control receiver 4 Air louvers 5 Water level indicator 6 Caster 7 Dustproof air filter 8 Cooling pad slot 9 Water tank 10 Power cord 11 Water tank knob 12 Ice pack 13 Remote control 7 S
12. ted by the palm tree icon on the display panel this setting will automatically vary the airflow speed between low medium and high Sleep Mode Sleep Mode Indicated by the moon icon on the display panel this setting will gradually lower the speed at different intervals depending on the selected fan speed If the fan speed is set to 3 the cooler will run for 30 minutes on high speed 30 minutes on medium speed and then continue to operate on low speed If the fan speed is set to 2 the cooler will run for 30 minutes on medium speed and then continue to operate on low speed If the fan speed is set to 1 the cooler will continuously run on low speed TIMER Button This evaporative cooler is equipped with a 7 5 hour programmable timer To set the timer press the TIMER button Each press of this button will add 0 5 hours to the set time The set time will be indicated in the middle of the display panel SWING Button Swing Indicator To activate the oscillation feature press the SWING button The fan head will automatically move from side to side which increases air circulation and distributes air more evenly 11 Say Goodbye to Ugly Products USING THE REMOTE CONTROL The Luma Comfort EC45S is equipped with a remote control A CR2032 3V coin type replacement battery is included for your convenience 1 To put the battery inside the remote control insert a coin into the slot located on the back of the remot
13. terior of the tank For excessive hard water buildup use a diluted vinegar solution and rinse thoroughly afterwards WATER PUMP MAINTENANCE Hard water buildup can affect the performance of the cooler s water pump To prevent malfunctions clean the pump and internal tubing with a calcium and lime cleaning product such as CLR at least once a season 1 Empty any water from the tank 2 Pour the cleaner into the water tank so the pump is covered 3 With the tank closed allow the pump to soak for 10 to 20 minutes 4 Remove the cooling pad from the back of the unit 5 Run the cooler for 30 seconds This will circulate the cleaning solution through the pump and tubing to remove any leftover mineral deposits Do not operate longer than 30 seconds or damage might occur to other parts of the cooler 6 Rinse the tank and fill it with clean water Run it for several minutes without the cooling pad in place to ensure the cleaning solution has been rinsed away 7 Replace cooling pad and dust filer and operate unit as normal 14 www LumaComfort com TECHNICAL SUPPORT Luma Comfort is committed to providing a premier service experience If you are experiencing any technical issues with your product related to either setup or operation please contact our product support team at 1 866 737 6390 or support lumacomfort com PRODUCT SPECIFICATIONS Model EC45S Product Dimensions 11 7 x 11 7 x 37 2 Product W
14. ure and improper power supply such as low voltage defective wiring or inadequate fuses Use of force or damage caused by external influences Complete or partially dismantled appliances THE WARRANTIES AND REMEDIES CONTAINED HEREIN ARE EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES EXPRESS IMPLIED OR STATUTORY INCLUDING ANY LIABILITY ARISING UNDER ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE STATUTORY OR OTHERWISE THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS WHICH MAY VARY FROM STATE TO STATE IN NO EVENT SHALL LUMA COMFORT BE LIABLE FOR ANY INCIDENTAL SPECIAL INDIRECT OR CONSEQUENTIAL DAMAGES WHETHER RESULTING FROM THE USE MISUSE OR INABILITY TO USE THIS PRODUCT OR FROM DEFECTS IN THE PRODUCT SOME STATES DO NOT ALLOW THE EXCLUSION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE LIMITATIONS MAY NOT APPLY TO YOU If you believe your product is defective contact Luma Comfort for warranty service at 1 866 737 6390 or support lumacomfort com In your correspondence with Luma Comfort please describe the problem and request a return material authorization RMA number You will also need to provide the proof of purchase return shipping address and a daytime phone number After a Luma Comfort representative confirms that your product is defective and is still under warranty you will receive an RMA and return shipping instructions Products sent to our headquarters without an RMA will be refused
15. www LumaComfort com WARRANTY Luma Comfort products are warranted to be free from defects in workmanship or materials for one 1 year from the date of purchase If the product is found to be defective within this period Luma Comfort at its sole option will repair or replace any components that fail during normal operation The repairs or replacement will be made at no charge to the customer for parts and labor assuming that the customer shall be responsible for all transportation costs to and from Luma Comfort Luma Comfort retains the right to repair or replace with a new or newly refurbished replacement product the appliance at its sole discretion This warranty does NOT apply to the following Products without a proof of purchase Products purchased from a source other than an authorized Luma Comfort dealer Cosmetic damage such as scratches or dents Damage caused by service performed by anyone who is not an authorized service provider of Luma Comfort Damage in transit Damage caused by accident abuse misuse water flood fire improper installation maintenance negligence commercial use for a non commercial unit acts of God or any other acts of nature or external causes Damage to a product caused by modifications or alterations without the written permission of Luma Comfort Normal wear and tear of parts that are designed to be replaced such as filters or batteries Power fail
Download Pdf Manuals
Related Search
Related Contents
Aterm WM3800R用クレードル取扱説明書 Kenroy Home 32599AMER Installation Guide User Manual for Induction Heater INCOIL model IH series BA-1031 MPC823ADSDB User`s Manual Levures liquides pour bière Wyeast Mode d`emploi Samsung MW81Y-WP User Manual TX500U_SPN_Manual (Page 1) K&M 17540 Copyright © All rights reserved.
Failed to retrieve file