CST Extractors - Online Kitchen Store
Contents
1. CST Extractors C D A Manual for Installation Use and Maintenance Important The CDA Group Ltd cannot be held responsible for injuries or losses caused by incorr product Please note that CDA reserve the right to invalidate the guarantee supplied with th installation or misuse of the appliance or use in a commercial environment This appliance is not designed to be used by people including children with reduced capacity or who lack experience or knowledge about it unless they have had supervision the appliance by someone who is responsible for their safety Under no circumstances should any external covers be removed for servicing or maintenan personnel Appliance information Please enter the details on the appliance rating plate below for reference to assist CDA Cu fault with your appliance and to register your appliance for guarantee purposes CE Declarations of Conformity This appliance has been manufactured to the strictest standards and complies with all applic safety Electrical safety LVD and Electromagnetic interference compatibility EMC IMPORTANT INFORMATION FOR CORRECT DISPOSAL OF THE PRODUCT IN DIRECTIVE 2002 96 EC At the end of its working life the product must be taken to a special local authority waste c providing appliance recycling services Disposing of a household appliance separately avoids possible negative consequences for t also enables the constituent materials to be recovered saving bo2. coal filter first open the base of the extractor as d up the charcoal filter shown as C in fig X to the base of the motor and turn it clockwise un Changing the Light DO NOT CHANGE THE LIGHT BULB IMMEDIATELY AFTER USE AS THE BULB W COOL BEFORE REMOVING IT Open the base of the extractor as described above unscrew the light bulb and replace th bulb as shown in the table below Finally replace the grease filter 40W max candle bulb SES screw type Table 1 Do not touch bulbs or adjacent areas during or straight after prolonged use of the lights The light is designed for use during cooking and not for general room illumination Extend the life span of the bulb Bulb replacement is not covered by the guarantee Only use bulbs recommended for your extractor Do not fit bulbs of a higher power rating may be adequate for use generally last longer and use less energy Spare bulbs are available from CDA Customer Care or from your local DIY shop Mains Electricity Connection THIS APPLIANCE MUST BE CONNECTED TO THE MAINS SUPPLY BY A COMPETE WIRING VIA A DOUBLE POLE SWITCHED FUSED SPUR OUTLET AND PROTECTED We recommend that the appliance is connected by a qualified electrician who is a member q comply with the I E E and local regulations The wires in the mains lead of this appliance are coloured in accordance with the Tees ST a following code BLUE NEUTRAL BROWN LIVE As the colours of the wires in the mains lead fo
3. mounted in one of two ways To fasten the product to the underside of a bridging cabinet remove the grease filter cover an cabinet using appropriate wood screws Not supplied To mount the hood on to a wall proceed as follows 1 Drill four holes as shown in the diagram below corresponding to positions B and Z on the diagram Note that the size of the holes dependant on the wall 2 Insert the wall fixings into the hole B and tighten the fixing screw leaving about 2 to 3m fixings in to the position Z for use later 3 Hang the hood on the fixing screws and secure the hood in position using two screws fixe Ducting and Ventilation For best performance and lowest noise output we recommend the use of 125mm ducting but this will impair performance If the extractor is to be used in recirculation mode ensure that the lever on the base of th to re circulating mode as shown in Fig 2 CDA To contact our Customer Care Department or for Service please contact us on the details below
4. r the appliance may not correspond with the coloured markings identifying the terminals connecting to the fused spur proceed as follows e The wire which is coloured blue must be connected to the terminal marked N Neutral or coloured black e The wire which is coloured brown must be connected to the terminal marked USE A 3 AMP FUSE L Live or coloured red NOTE USE A 3A FUSE Assembly and electrical connection should be carried out by competent personnel When installing this product we recommend you seek the help of another individual IMPORTANT THIS APPLIANCE IS A CLASS II APPLIANCE DOUBLE INSULATED A BE EARTHED DO NOT FIT AN EARTH LEAD TO THIS EXTRACTOR Do not mount the isolation switch behind the chimney section It is a requirement that yo extractor from the mains electrical supply after installation This appliance is intended to be connected to the mains electrical supply by means of an is and is intended to be protected by a 3A fuse The use of a 13A fuse can cause damage to t of a fault and may also invalidate the warranty Electrical Information Mains electrical voltage 230 240Vac Total rated power consumption 165W Troubleshooting Please note Your extractor is equipped with a motor protection device that will switch off the mo overheating This may happen during cooking when most or all of the zones burners are This is normal and the extractor will work again once the motor has cooled
5. sufficiently Please note e Your extractor is equipped with a motor protection device that will switch off the moto from overheating This may happen during cooking when most or all of the zones bur simultaneously This is normal and the extractor will work again once the motor has co If your extractor is not working 1 Check that the mains supply has not been switched off 2 Check that the fuse in the spur has not blown Contact CDA Customer Care A Customer Care Department The CDA Group Ltd Harby Road Langar Nottinghamshir T 01949 862 012 F 01949 862 003 E service cda eu W www cda eu Installation When the extractor is to be installed above an electric hob the minimum distance between th 600mm 650mm is recommended When the extractor is to be installed above a gas hob the minimum distance between the 700mm 750mm is recommended If the instructions provided with your gas hob state that the required distance between the h than 700mm then that is the distance that should be observed this is a legal requirement disconnected from the gas supply and the installation being reported to RIDDOR The heig top of the burners IN THE ABSENCE OF ANY INSTRUCTIONS SUPPLIED WITH THE GAS HOB THE MI THE HOB AND EXTRACTOR MUST BE AT LEAST 760mm The width of any hob must not be greater than the width of the extractor installed above it gt FOOT QAP recommended Mounting your Extractor The extractor can be
6. th energy and resources dispose of household appliances separately the product is marked with a crossed out whe Please note e Under no circumstances should the extractor be connected to any gas ventilation syste ducting system e Do not vent the extractor into an attic or loft space e Only house the extractor in rooms with adequate ventilation Remember that the extr whatever air is extracted needs to be replaced e Donottile the extractor in It should be removable for service or maintenance e Do not use silicone sealant to secure the hood to the wall e You must be able to isolate the extractor from the mains electrical supply after installat e This extractor has been designed to be used in a room with a volume of less than 36 m e Steam cleaners must not be used when cleaning this appliance e The performance of your extractor will vary depending on a number of factors These i length of ducting room volume ventilation available and cleanliness of the filters Using your Extractor For best performance you should switch on the extractor 15 minutes before starting t approximately 15 minutes after the end of cooking Control Panel A Light switch B Power indicator C Power switch To switch the extractor light on or off e Slide the light switch to position A1 for off or A2 for on To switch on the extractor or change the motor speed e Slide the power switch to the position required dependent on
7. the speed you require To change the speed at any time when the extractor is running e Press the relevant D button for the speed level required To switch the extractor off e Slide the power switch to position C1 for off Care and Maintenance IMPORTANT DO NOT PERFORM MAINTENANCE OR CLEANING OF THE EXTR SWITCHING OFF THE ELECTRICITY SUPPLY Cleaning You should use a nonabrasive cleaner Any abrasive cleaner including Cif will scratch the control panel markings You can clean your extractor effectively by simply using a dilute solution of water and mil shine with a clean cloth for example the CDA E Cloth Cleaning the grease filter The grease filter should be kept clean to minimise the risk of fire At least once a month you should remove and clean the grease filter with hot soapy wa grease filter in a dishwasher ensuring that you place it in an upright position to prevent d the dishwasher After rinsing and drying replace the filter To remove the grease filter first open the base of the extractor by sliding the clips across clips as shown in figure X before removing the grease filter itself To replace the greas reverse Please note Cleaning the filter in the dishwasher may lead to discoloration This is normal and does no appliance Changing the charcoal filter re circulating only To ensure best performance of your extractor you should replace the charcoal filters depending on use To attach a new char
Download Pdf Manuals
Related Search