View - Multifit
Contents
1. box RK Type B a For indoor vl Dispose of applied part use only I O product correctly Cover unit plug cover 4 interchanging standard and large leg rests The leg rests are fixed to the lift arm by four bolts through a Stand the LegLifter so that both sides of the appliance are the white block on the lift arm into four nutserts on the round easily accessible plate underneath the leg rest Both leg rest models have identical 2 Use an Allen key to remove the four bolts located on the nutsert layouts to facilitate interchange white block behind the leg rest Retain the washers with the bolts Standard leg rest underside Installed leg rest B Remove the leg rest from the appliance Position the replacement leg rest so that its four nutserts locate into the four s Wide leg rest underside recesses in the back of the white block on the actuator Replacement leg rest 4 With washers intact carefully screw the bolts back into position by hand to avoid damaging the bolt and nutsert threads Ei When all the bolts are installed and finger tight tighten them further with the Allen key Installation to standard domestic innerspring boxframe and slat beds K On the selected accessible side of the bed slide the stabiliser a Eg between the mattress and bed base about 600mm from the 600mm bedhead bracket upwards with the stabiliser nut facing out For frame beds with a r2. User Manual Information index Multifit LegLifter Mk3L Components Diagram shows LegLifter unit assembly for LEFT bedside Right bedside assembly is opposed left to right TEWO R Handgrip Bolts Stabiliser back fitting plates and washers Stabiliser cord Control box and power cable Leg rest wide option Actuator rod Stabiliser bar yY Adjustable foot Motor unit Multi multifit co nz Ww W new Thank you for purchasing this Multifit LegLifter This is a quality long lasting appliance designed to give you many years of trouble free service For your own safety ensure that you and others involved in the use of this appliance read these instructions carefully If you are uncertain about any instruction or if you need further information please contact your distributor General description and intended use The Multifit LegLifter is a motor driven appliance designed to provide independence for disabled people who are unable to lift their legs from a bedside sitting position to the surface of the bed With simple push button commands the LegLifter gently and smoothly carries the legs from the bedside to the prone position on the bed surface The conveniently located handgrip can be used to aid transfer on and off the bed as well as to assist with balance while reclining Depending on the level of disability the process can be performed with minimal or no assistance from another person With t
3. age common neglect misuse accidental damage unauthorised alteration or repair by unauthorised persons or use of a power supply control box other than that supplied with the appliance In the event of defects in manufacture or materials occurring within the warranty period Multifit will rectify the fault free of charge on provision of the original purchase invoice dated no more than two years prior to date of claim EC Declaration of Conformity C proof CEproof International Ltd Hilliard House Lester Way Wallingford Oxfordshire OX10 9TA United Kingdom Description of product Multifit LegLifter Model Mk3 and Mk3L Serial Nos 00004 10000 Name of manufacturer Address Multifit Hospital Supplies Ltd 10 Pohutu St Whakatane New Zealand PO Box 748 Whakatane 3120 New Zealand We hereby declare that the product described above complies with the relevant provisions of the appropriate EC Directives Harmonised Standards of the European Union and other recognised standards listed below and accordingly carries CE marking Medical Devices Directive 93 42 EEC Electromagnetic Compatibility Directive 2004 108 EC Low Voltage Directive 2006 95 EC The following standards are applicable EN 55014 1 2006 EN 61000 3 2 2006 EN 55014 2 1997 A1 2001 EN 61000 3 3 1995 A1 2001 A2 2005 EN 55022 1998 A2 2003 EN 61558 1 2005 EN 55024 1998 A2 EN 61558 2 6 1997 Date of Declaration 12 11 2009 Date of Issue 12 11 2009 W
4. an dry place Trouble shooting guide If the appliance does not operate on command check the following and test individually after each action Ensure that mains power cable is connected and switched on Ensure that the keyways on all plugs and sockets are aligned correctly and that all plugs are connected firmly to the control box If the appliance has been used excessively the overload switch in the control box will activate Allow the unit to cool The overload switch will reset when the unit has returned to a normal working temperature If your handset has an active key lock check that the key is inserted correctly The handset is immobilised if the Safety bar i including blankets to full downward movement of the key is removed _ The safety bar which turns the motor off on sensing an obstruction behind the leg rest may have been activated Ensure that there is no hindrance leg rest to the bedside Ensure that both upward and downward trajectories of the leg rest have clear passage End of life disposal of appliances The appliance s electrical and electronic components cannot be discarded through general waste disposal Return the complete unit to your supplier where it may be renovated for further use or recycled at an authorised facility The Multifit LegLifter control box conforms to the requirements of EMC directive 2004 108 EC and Low Voltage Directive 2006 95 EC The actuator an
5. ayne Manson Managing Director Multifit Hospital Supplies Ltd CEproof International Ltd Keeper of Technical Documents in the European Union Your Multifit LegLifter distributor
6. d handset are considered benign for electromagnetic immunity and emissions Specifications Total weight of system 16 kg Weight of LegLifter unit 9 kg Width of unit without leg rest 60 mm Overall length of unit 1050 mm Installation time 10 minutes Adjustment range of unit 300 700 mm Width of leg rest Standard 285 mm Wide 485 mm Maximum user load legs only 67 kg Determined by width of user s legs across both calves and the leg rest model to suit Overall width of user s calves must not exceed above widths for selected leg rest Tested to carry 67 kg load without failure safety factor over 4x Power supply from control box 28V TiMotion TC2B control standard TiMotion TC1 control optional Refer page 3 for details Note Do not use any control box other than the model supplied with the appliance Operating temperature range 10 C 40 C 30 75 Multifit Hospital Supplies Ltd M U Itifiz PO Box 748 Whakatane 3120 New Zealand Tel 64 7 308 0045 www multifit co nz export multifit co nz 2010 Multifit Hospital Supplies Ltd The Multifit LegLifter appliance is a patented device Multifit and LegLifter are trademarks of Multifit Hospital Supplies Ltd Published June 2010 Relative humidity range Warranty Multifit Hospital Supplies Ltd guarantees the Multifit LegLifter system for a period of two years against defects in materials and workmanship This excludes fair wear and tear wilful dam
7. gLifter is supplied in flatpack for shipping and storage Check the Wide leg rest 485mm wide pack components with the appropriate diagram on the front cover of this manual gt to ensure all items have been included Mains lead Do you require an optional battery back up in event of mains power failure se elite lt 4 TC2B Control Box standard offers battery backup 2 x 9V alkaline edie batteries not included in kit for emergency LOWERING ONLY of the leg rest Battery recess The TC2 battery back up provides ONE lowering operation only new batteries A are required for the next operation Standard 9V alkaline batteries are usually ctuator plug connection widely available and may be installed by your distributor on request To insert batteries 1 Disconnect control box from mains supply 2 Remove battery cover and connect batteries 3 Insert batteries into recess and replace cover lt a TC1 Control Box optional offers a separate rechargeable battery pack TC1 Mains lead Charging which automatically recharges every time the appliance is used on mains power z lt r supply In event of mains power outage the battery provides up to six lifting Control id and lowering operations from a fully recharged battery unit depending on the box Y weight of the patient s legs j TEULE Classifications reference plug a z t k BAE Double Fail safe safety C CE marking insulation isolation transformer 93 42 EEC Control Battery
8. he correct attachments the LegLifter may be fitted to standard innerspring beds slat beds divan beds and some profiling beds See Specifications on page 8 for the range of adjustment Consult your distributor regarding correct configuration for your specific bed type Safety features Safety bar on the lift arm turns the motor off in event of obstruction in the downward motion of the leg rest Telescopic support prevents leg rest lowering under power in event of obstruction Smooth profile and rounded edges reduce injury risk Green light on the handset turns on to warn that the leg rest is in motion or in a raised position The light turns off when the leg rest is fully raised It also turns off when the leg rest is returned completely to the bedside where it will not present an obstacle to getting out of bed A key lock for the handset which immobilises the handset when the key is removed is available on request Low 28V power to the LegLifter appliance Limitations on use The LegLifter must not be used to lift anything other than the legs of the person for which it is intended and only when they are seated correctly on the edge of the bed The LegLifter should not be used to lift the complete weight of a person The LegLifter should not be be used or operated by a child under the age of 12 years The LegLifter is not intended to lift the legs out of bed The LegLifter should not be operated by people without the ability o
9. ical parts Using a household or hospital grade detergent solution wipe with a damp cloth Dry thoroughly To disinfect wipe all surfaces thoroughly with either alcohol impregnated wipes mild disinfectant solution or spray and allow to dry Regularly clean your Multifit LegLifter particularly around the pivot point at the lower end of the appliance the underside of the leg rest and handgrip Never use water blasting as a cleaning method for this appliance Store the appliance in a clean dry place Regular maintenance check Your Multifit LegLifter is designed and manufactured to the highest quality standards for materials and craftsmanship to minimise maintenance and to ensure many years of satisfactory service However a regular check for signs of wear will ensure a longer working life for your appliance Check for signs of possible wear to the following Date month year underside of the leg rest pivot bushes actuator rod thread actuator carriage nut actuator rod end bearings BERACE R s n Multifit recommends that the LegLifter be inspected every year by your supplier or other suitably authorised person Storage Clean the Multifit LegLifter and ensure that it is completely dry before storing Wrap a dust cover around the appliance or return it to its original packing box for protection Store the entire Multifit LegLifter system components together in a cle
10. im to contain the mattress use the adjustment bolts to align the brackets flush with the edge of the bedframe For frame beds adjust bolts to align stabiliser bracket flush with edge of bed frame Bring both cords under the mattress to the far side of the bed 2 On the far side of the bed clip one end of the cord to the ring on the back fixing Thread the other end of the cord through the hole in the black plastic cleat B Insert the back fixing between mattress and bed base centred opposite the stabiliser bar Pull on the cord until it is taut 4 Place the LegLifter at the accessible side of the bed with the handgrip towards the bedhead Align the vertical slot nearest the bedhead over the corresponding stabiliser nut Screw the fixing bolt washer and plate into position by hand 5 Turn the adjustable foot until the pivot point is about 75mm below the top of the mattress Lift the lower end of the unit onto the corresponding stabiliser nut Gi Screw the fixing bolt washer and plate into position by hand Lift the lower end of the unit and align the pivot points so that E y ean they are level parallel to the top of the mattress Tighten the bolt with the Allen key until the plate fits snugly into its recess and the Clear space under unit allows for Height adjustment bedside trolley table access lower end is firmly supported lt gt fc Tighten the bolt nearest the bed head with the Allen key un
11. model supplied with the LegLifter unit Before installation 3 Is your Multifit LegLifter configured for correct bedside access lt gt p lt a To suit individual preferences for bedside access the Multifit LegLifter is configured before delivery to fit on either the LEFT or RIGHT side of the bed viewed from lying on the bed with the leg rest facing out Confirm that your LegLifter is correctly configured for your preferred bedside access lt Fitted for right bedside gt r l Is your Multifit LegLifter suitable for your bed design The standard Multifit LegLifter MK3 is supplied with a stabiliser bar and Fitted for lett i Re bracket designed for installation to a typical innerspring domestic bed Multifit bedside gt can also supply stability bars and brackets designed to cope with the mattress retaining rim typical of many box base and slat bed designs Multifit LegLifter model MK3 L is designed for fitting to adjustable profiling a beds Manufacturing specifications vary and your profiling bed supplier should Standard leg rest 285mm wide be consulted to arrange installation See page 6 of this manual for instructions A S Is the supplied leg rest the most suitable size for your patient lt a Multifit LegLifter Mk3 offers options of a standard leg rest or a wider leg rest for patients affected by conditions of heavy or swollen legs Have you received all Multifit LegLifter components Multifit Le
12. r understanding to operate the handset control Safety precautions Properly dispose of all plastic wrap from your Multifit LegLifter packaging away from the reach of small children Ensure that control unit voltage and cables are intended for your power supply During installation ensure that the LegLifter s stabiliser back fitting is securely fastened on the opposite side of the bed base and that the LegLifter fits firmly and securely against the bedside See page 5 After installation ensure that the control box and power cords are tucked away from traffic areas to avoid trip hazards Before operation ensure that all power connections are firmly inserted Keep small children away from the LegLifter while it is in use and keep the operator handset out of their reach Ensure the user is physically and mentally able to use the LegLifter safety Allow plenty of clear space beside the bed to enable easy access to and from the bedside which may include wheelchair space Ensure at least 600mm clear space for the lift arm to operate without obstruction and ensure that no objects including blankets can interfere with free movement of the lift arm and leg rest To avoid the unlikely event of overheating of the actuator under heavy load recommended active inactive operation ratio is eg 2 minutes operation intermittent per 20 minutes of non operation Do not use any other power control box other than the TiMotion TC2B or TC1
13. t the bed head as the legs begin to rise with the intention of resting the head on the centre of the pillow The lifting action will deliver the legs towards the centre of the mattress and stop automatically The handset light turns off when the leg rest has finished its upward motion 4 Press the DOWN button on the handset The handset light turns on to indicate the downward motion The leg rest will withdraw from under the legs The legs may then be adjusted to a more comfortable position if necessary 5 The leg rest stops automatically on reaching its original bedside position The handset light turns off Getting out of bed E Before getting out of bed ensure that the leg rest is fully lowered to check handset light will be off when the DOWN button is pressed M Use the handgrip to assist sitting in bed HM Move the legs over the bedside and let gravity take the feet to the floor Note The Multifit LegLifter is not designed or N recommended to carry the legs out of bed To perform the task of getting out of bed with the LegLifter the upper body would have to be raised to a sitting position at the same speed as the legs are being lowered This may cause difficulty distress or injury to a disabled person We recommend the above method for getting out of bed Maintenance and trouble shooting guide Cleaning Disconnect from the power source before cleaning Do not allow any moisture to get into electr
14. til the plate fits firmly into its recess EJ On the far side of the bed pull the cord taut and then upward to lock the cord in the black plastic cleat of the back fixing Tuck any remaining cord out of sight under the mattress 9 Connect the handset to the control box ensuring that the keyways of the plug and socket are properly aligned as you insert the plug Ensure that the connection is secure Hang the handset on the bracket near the handgrip Connect the mains power lead to a power outlet Ensure that the connection is secure Position Actuator the control box and power lead safely out of traffic areas where power lead they could cause a trip hazard Handset plug 10 Turn the power on at the power outlet Activate the UP and a ains power DOWN buttons on the handset to check for smooth operation to control box i For an overview and additional assistance on installation view the Multifit LegLifter Installation video on www multifit co nz How to use the Multifit LegLifter Getting into bed Ei Sit on the bedside with the buttocks as far into the bed as possible with the legs draped directly over the leg rest Hold the LegLifter handgrip with one hand to assist balance 2 Holding the handset with the free hand press the UP button to start the lifting action The green handset light will turn ON to indicate that the leg rest is in motion B Keep the free hand on the handgrip Recline onto the elbow neares
Download Pdf Manuals
Related Search