User Manual
Contents
1. s Ducking or Gating A variation on stereo operation as described above is master slave operation where the gain of one 2051 is controlled from another unit but without reciprocal action This is useful where a voice channel input is required to reduce the gain of for example background music when the microphone signal is present The link cable should be fitted as for stereo operation but the Stereo Link switch should only be depressed on the slave 2051 the backgound music channel in the example above If the compressor is switched out on the master unit gain reduction will only occur on the slave unit The threshold and ratio controls on the master 2051 will determine the extent of the gain reduction in the slave unit Equalisation The 2051 equaliser section has four bands each with continuously variable cut and boost control and switched frequency selection Each band has a filter with a relatively low Q of approximately 0 5 with a broad control range and moderate overlap between the bands LF Band The LF Low Frequency band of the equaliser has a shelving characteristic i e it extends from the selected frequency to the extreme low frequency limit of the equaliser s response The corner frequency of the LF band is selected by a push button to 120Hz or 80Hz and the cut or boost is controlled by a continuously variable centre detented rotary knob At the selected corner frequency up to 12dB of cut2. 30 Gain Make Up 0 to 20dB Equaliser LF Band 12dB at 80Hz or 120Hz Shelving response LM Band _ 12dB at 250Hz 500Hz 1KHz or 2K2Hz Peaking response Q 0 5 HM Band 12dB at 1K5Hz 2K2Hz 3K6Hz or 5KHz Peaking response Q 0 5 HF Band 12dB at 8KHz or 12KHz Shelving response Bargraph Meter Switchable to output level or compression 0dB 4dBu Output Fader Rotary fader 0dB at centre 18dB maximum gain Outputs Electronically balanced unbalanced compatible Output impedance 47 ohms Maximum level 26dBu 3 pin male XLR connector Unbalanced Outputs Output impedance 47 ohms Maximum level 18dBu into 10Kohms 2 pole 0 25 jack socket Frequency Response 10Hz to 40KHz 0 1dB Dynamic Range 108dB Line input OdB gain Sidechain Insertion Points Unbalanced switched 3 pin jack socket tip send ring return Nominal level 2dBu Output impedance 47 ohms Return input impedance 10Kohms Power Requirements Dimensions Weight Rear panel selectable for 220 240V 50Hz or 110 120V 60Hz operation Rear panel fuse 20mm 1 AT 250V Power consumption 30VA typical Detachable 3 pin IEC connector mating connector and cable supplied Front panel On Off switch with green LED 19 rack mounting 1U high 483mm wide x 44mm high x 250mm deep 4Kg The above specifications are subject to change without notice SERVICE Should the processor
3. require service it must be taken or posted to an authorised dealer Please retain the original packing for possible future use and ensure the unit is suitably protected during transit The manufacturer cannot accept responsibility for damage caused during transportation The processor is supported by a limited warranty for a period of one year from the date of purchase During this period any faults due to defective materials or workmanship will be repaired free of charge The warranty excludes damage caused by deliberate or accidental misuse operation on the incorrect mains voltage or without the correct type and value of fuse fitted It is the user s responsibility to ensure fitness for purpose in any particular application The warranty is limited to the original purchase price of the equipment and excludes any consequential damage or loss Please retain proof of purchase and record the following details Serial Numbet cceee eee Date purchased cscccisvescctSin tas Dealerin cesses Maelo a
4. the compressor section Depending on the EQ settings the compressor response will be modified The effect may be compared by toggling the pre switch Master Section Master Level The master level control is an output fader which enables the voice processor output to be matched to the following equipment The control is calibrated for OdB at its centre with a further 18dB of gain available by turning the knob fully clockwise The additional gain may be useful if the output of the voice processor is connected directly to a digital recorder which requires a high level of modulation Note that applying additional gain at the output will not increase the dynamic range of the signal but will increase the noise level as well as the audio signal being recorded and should therefore only be used if an output level in excess of the nominal 4dBu is required Bargraph Meter The processor is equipped with an 8 segment LED bargraph meter The meter normally monitors the audio output from the unit and is calibrated for nominal level of 4dBu at the balanced output OdB Similarly 0dB on the meters also corresponds to 10dBu at the unbalanced output The reference point may be internally adjusted by your dealer if required The output level scale is printed above the bargraph The meter may be switched to indicate the amount of compression applied to the signal by operating the GAIN RED N switch If the signal is below the threshold the meter w
5. this manual fully before installing or operating the Voice Processor PRECAUTIONS The T L Audio VP 2051 Voice Processor requires very little installation but like all electrical equipment care must be taken to ensure reliable safe operation The following points should always be observed All mains wiring should be installed and checked by a qualified electrician Ensure the correct operating voltage is selected on the rear panel before connecting to the mains supply Never operate the unit with any cover removed Do not expose to rain or moisture as this may present an electric shock hazard Replace the fuse with the correct type and rating only Warning This equipment must be earthed INSTALLATION AC Mains Supply The unit is fitted with an internationally approved 3 pin IEC connector A mating socket with power cord is provided with the unit wired as follows Brown Live Blue Neutral Green Yellow Earth Ground All mains wiring should be performed by a qualified electrician with all power switched off and the earth connection must be used Before connecting the unit to the supply check that the voltage selector switch on the rear panel is correctly set The unit may be set for 115V accepting voltages in the range 110V to 120V 60Hz AC or to 230V for voltages in the range 220V to 240V 50Hz AC Adjustment to the operating voltage should be made by sliding the selector switch left or right wi
6. T L Audio INDIGO SERIES User Manual VP 2051 VALVE VOICE PROCESSOR Tony Larking Professional Sales Limited Letchworth England Tel 01462 490600 International 44 1462 490600 Fax 01462 490700 International 44 1462 490700 INTRODUCTION The T L Audio Indigo Series combines classic valve techniques with low noise solid state circuitry to produce audio processing units offering very high quality signal paths with comprehensive control facilities and the unique valve sound The VP 2051 is a single channel valve voice processor combining a high quality microphone pre amplifier four band equaliser and a compressor All parameters of the compressor are variable and a link facility enables two units to be operated in stereo mode The bargraph meter may be used to display output level or gain reduction The block diagram of the unit is shown in fig 1 Each channel has four input sources balanced microphone and line inputs via XLR connectors plus an unbalanced line level input via a jack socket and an instrument input also on an unbalanced jack socket but located on the front panel where it provides a convenient means of patching a guitar or keyboard directly into the processor The gain of the input stages is controlled by a centre detented control calibrated for OdB nominal gain from the line input sources at the centre and providing up to 60dB of microphone gain The instrument input has a sensitivity switch associated with it
7. and boost are available Typical response curves are shown in the specification section of this manual LM Band The LM Low Mid Frequency band has a peaking characteristic i e it boosts or cuts a section of the audio spectrum around its selected centre frequency only A four position rotary switch is used to select the centre frequency to 250Hz 500Hz 1KHz or 2K2Hz The mid bands possess a low Q wide bandwidth response which results in effective equalisation without harshness and this means that there is a good degree of overlap between the frequency options The amount of cut or boost is again controlled by a continuously variable centre detented rotary knob with up to 12dB of cut and boost available at the centre frequencies Response curves for the mid bands are also shown in the specification section of this manual HM Band The HM High Mid Frequency band is similar in operation to the LM band except that the centre frequencies are obviously higher and concentrated in the critical upper vocal region of the spectrum The available frequencies are 1K5Hz 2K2Hz 3K6Hz and 5KHz HF Band The HF High Frequency band has a shelving characteristic complimenting the LF band Corner frequency selection is by push switch to 8KHz or 12KHz Bypass The Equaliser In switch allows the processing to be bypassed for comparison of the equalised and original unprocessed signal EQ Pre The pre switch places the equaliser ahead of
8. ctions Audio Inputs Microphone Input The microphone input is via 3 pin female XLR connector suitable for balanced or unbalanced microphones The mating connector should be appropriately wired as follows for balanced or unbalanced operation Balanced inputs Pin 1 Ground screen Pin 2 Signal Phase also known as or hot Pin 3 Signal Non Phase or cold Unbalanced inputs Pin 1 Ground screen Pin 2 Signal Phase or hot Pin 3 Signal Ground Line Input The line level input is also via a 3 pin female XLR connector suitable for balanced or unbalanced line sources at a nominal level of 4dBu The mating connector should be appropriately wired as follows for balanced or unbalanced operation Balanced inputs Pin 1 Ground screen Pin 2 Signal Phase also known as or hot Pin 3 Signal Non Phase or cold Unbalanced inputs Pin 1 Ground screen Pin 2 Signal Phase or hot Pin 3 Signal Ground When using unbalanced signals the signal ground may be obtained by linking pins 1 and 3 in the mating XLR connector If this connection is not made a loss in level may result Unbalanced Line Inputs An unbalanced line level input at a nominal level of 10dBu is also provided on a 0 25 mono jack socket The mating plugs should be wired as follows Tip Signal Phase or ho
9. e output of the compressor stage allows the signal level to be brought back to the same loudness as the uncompressed signal Frequency selective compression may be obtained by inserting an equaliser into the sidechain signal from which the control voltage is generated Boosting a range of frequencies will have the effect of lowering the compressor threshold at those frequencies i e making the compressor more sensitive Note that the equalisation is not applied to the audio output but is used to modify the control sidechain A common use of sidechain equalisation is de essing to reduce sibilance on vocals Suitable equalisers which can be inserted into the sidechain are the TL Audio Indigo Series 2011 or 2012 valve equalisers which match the 2051 in audio levels and styling Threshold The 2051 compressor section has a variable threshold set by a rotary control calibrated from 20dBu to 20dBu resulting in increased compression as the control is rotated clockwise Attack and Release The attack time is switchable to 0 5msec or 20msec At 0 5msec attack the compressor is fast enough to reduce the gain of a 1KHz signal in less than half a cycle effectively preventing an overload of any following equipment which has limited headroom such as a digital processor tape machine or transmitter The release time is switchable to 40msec or approximately 2 seconds Adjustment of the attack and release times allows unobtrusive compression t
10. ill not illuminate i e no gain reduction is occurring As the signal passes through the threshold the 0dB LED will illuminate indicating that gain reduction has started For further increases in input level the meter will indicate the gain reduction occurring at the compressor stage Note that the gain reduction indicated is a measure of the degree of compression and does not include any gain make up applied The gain reduction scale is printed beneath the meter SPECIFICATIONS Microphone Input Electronically balanced Input impedance greater than 2Kohm Gain range 10dB to 60dB Noise 127dBu EIN with 150 ohm source 22Hz 22KHz and maximum gain 3 pin female XLR connector Phantom Power 48V at 10mA maximum per microphone High Pass Filter 3dB at 90Hz 12dB per octave Balanced Line Input Electronically balanced unbalanced compatible with input impedance greater than 5Kohm Gain range 20dB to 20dB Nominal input level 4dBu Maximum input level 26dBu 3 pin female XLR connector Unbalanced Input Input impedance greater than 5Kohm Gain range 20dB to 20dB Nominal input levels 10dBu Maximum input level 12dBu 2 pole 0 25 jack socket Auxiliary Input Switchable for high or low gain plus 40dB gain variation Maximum input level 18dBu 2 pole 0 25 jack socket Compressor Threshold 20dBu to 20dBu Attack 0 5msec or 20msec Release 40msec or 2 seconds Ratio 1 1 5 to 1
11. imum may result in a loud click or thump in your monitor loudspeakers Microphone Input When using the voice processor with a microphone input care should be taken not to apply too much gain at the input Start with the input gain control set to minimum and the output master at the mid point 12 o clock position The input gain can then be gradually increased until the peak LED illuminates on the loudest peaks only The master output level should then be adjusted to produce the required output Line Input A line level signal should already be at about the correct operating level but this may be checked by bypassing the compressor i e turning off the COMP IN switch and monitoring the level on the bargraph meter The input gain should be adjusted until the 0dB LED is illuminated on music of normal loudness with the red LEDs illuminating occasionally on higher volume peaks Aux Input The front panel auxiliary input sockets may be switched between high level signals LO GAIN suitable for active guitars and keyboards and low level signals HI GAIN suitable for microphones pick ups or passive guitars and are also controlled by the input gain control LF Cut Filter The voice processor is equipped with high pass low frequency cut filter which may be used to remove unwanted low frequencies from the input signal It is effective in reducing hum rumble caused by traffic or wind noise and excessive LF signal conte
12. nced jack socket The mating connector should be wired as Tip Signal Phase or hot Screen Ground Note The link signal is a DC control voltage Do not connect the link socket to an audio signal connector It is only suitable for connection to the link socket on another voice processor Ventilation The unit generates a small amount of heat internally This heat should be allowed to dissipate by convection through the grills in the side panels and top cover which must not be obstructed Do not locate the unit where it will be subject to external heating for example in the hot air flow from a power amplifier or on a radiator The voice processor may be free standing or mounted in a standard 19 rack Rear Panel The rear panel connectors are identified in fig 3 Make sure that all settings mains and audio connections have been made as described above before attempting to operate the equipment OPERATION Front Panel The front panel controls are identified in fig 2 Pre Amplifier section Phantom Power 48V Phantom power may be applied to the microphone input socket by depressing the 48V switch on the front panel Phantom power should only be used with suitable microphones i e condenser microphones WARNING Always turn the master output level to minimum before switching phantom power on or off and before connecting or disconnecting a microphone Failure to set the level to min
13. nt from close mic applications Phase Reverse The phase reverse switch changes the polarity of the input signal The effect is not apparent with a single microphone setup but is essential to correct any phase error in a stereo application or where the processor is patched into the insertion point of a mixing console A phase error typically appears as an apparent loss of bass Compressor Section Compressor Operation A compressor functions by reducing the gain of the signal when it exceeds a certain level or threshold The amount of gain reduction may be fairly gentle through to limiting where the signal is clamped at the threshold level The amount of gain reduction is determined by the ratio control which is calibrated as a ratio of the output to input signals The gain of the signal is reduced by a voltage controlled circuit Variable time constants are applied to the control voltage to adjust the rate at which the gain is reduced called the attack time and the rate at which unity gain is restored after the signal returns to below the threshold referred to as the release time The effect of compression is to limit the dynamic range of a signal It may be used to keep a variable output from a bass guitar for example at an even level or to add punch to vocals drums guitar or a complete mix Whist the subjective sound quality can be improved by compression the overall signal level may be reduced A gain make up control at th
14. o be applied to virtually any audio signal but should very short transients occur the time constants become signal dependant generally reduced to prevent a slow release leaving a hole in the signal after the transient Also a fast release setting will be extended by a slow attack setting Due to this automatic modification of the time constants the controls are simply calibrated fast and slow Ratio The ratio may be varied from 1 1 5 very gentle compression to 1 30 near limiting The compressor normally operates with a soft knee i e the compression is gradually introduced as the signal passes the threshold in which case the ratio refers to the compression eventually obtained Gain Make Up Up to 20dB of gain make up may be applied to retain the subjective loudness of the signal Bypass The Compressor In switch allows the processing to be bypassed for comparison of the compressed signal with any gain make up that has been applied with the original signal Stereo Operation Two 2051 voice processors may be configured for stereo operation of the compressor section by inserting a Link cable between the two units In this mode the control voltages are linked ensuring that the same amount of gain reduction is applied to both channels even if one signal is below the threshold This ensures that the stereo image is preserved To active this mode the Stereo Link switch should be depressed on both 2051
15. t Screen Ground Auxiliary Inputs A 2 pin mono jack plug is required which should be wired as follows Tip Signal Phase or hot Screen Ground The auxiliary input is suitable for direct connection of instruments including guitars and keyboards Good quality screened cable should be used particularly for microphone or low level sources to prevent hum or noise pickup Insertion Point The insertion point is interfaced via a 3 pin 0 25 switched jack socket on the rear of the unit The pin connections are Sleeve Ground II Tip Send Ring Return The insertion point is unbalanced and operates at a nominal level of 2dBu If used as an additional send only e g as a send to a tape machine or monitor mixing desk the Tip and Ring should be wired together to preserve the signal path through the insertion point When used in this manner the send will be post compressor Balanced Output The output is via a balanced 3 pin male XLR connector The mating connector should be wired as follows Pin 1 Ground screen Pin 2 Signal Phase or hot Pin 3 Signal Non Phase or cold Unbalanced Output An unbalanced line output is provided for each channel on a 0 25 mono jack socket Tip Signal Phase or hot Screen Ground Link connection The compressor section stereo link facility is via an unbala
16. th a small screwdriver until the desired voltage is displayed The mains fuse required is 20mm anti surge 1AT rated at 250V If it ever necessary to replace the fuse only the same type and rating must be used The power consumption of the equipment is 30VA Warning attempted operation on the wrong voltage setting or with an incorrect fuse will invalidate the warranty Audio Operating Level The voice processor is equipped with inputs and outputs suitable for connection to a wide variety of other audio equipment Generally the balanced XLR connections will be required for interfacing to other professional equipment where the operating level line up level or nominal level will be 4dBu or approximately 1 2V rms The unbalanced jack connectors are generally intended for interfacing to semi professional equipment and have an operating level of 10dBu or about 225mV rms The processor may be used to change between operating levels for example by connecting the unbalanced output of a semi pro mixing console to the processor s unbalanced input and taking the balanced output of the processor to the balanced input of a tape machine at 4dBu All line level inputs and outputs of the processor may be used simultaneously if required Balanced interconnection is always preferable to obtain the best headroom and noise rejection but can only be used if the other equipment in the chain e g the mixing console also has provision for balanced conne
17. to match the gain to a low level pickup e g a passive guitar or microphone or a higher output source such as a keyboard or active guitar and is also controlled by the input gain potentiometer The equaliser is fully valve based providing up to 12dB of cut and boost at the selected frequencies The EQ PRE switch positions the equaliser before pre or after post the compressor The compressor comprises a valve core with solid state sidechain processing The sidechain monitors the output of the compression stage and generates a control signal which varies the attenuation of the compressor The sidechain processing includes fully variable control of the compressor threshold and ratio plus switched fast and slow time constants for attack and release Frequency dependant compression for example de essing may be achieved by placing an equaliser into the sidechain insertion point An independent gain make up control is provided to retain the subjective loudness of a compressed signal plus an overall master output level control The output control has a nominal OdB of gain at its centre with up to 18dB of further gain available to ensure full modulation of digital recorders The output is via a balanced XLR socket at a nominal level of 4dBu with an unbalanced output on a jack socket at a nominal level of 10dBu An LED bargraph meter is provided which may be switched to monitor the output signal level or compression applied Please read
Download Pdf Manuals
Related Search