Semi Automat - Stratton Sales
Contents
1. IMPORTANT INSTALLATION NOTICE ERIKA SEMI AUTIOMATIC DIVIDER ROUNDER FILLING OF OIL RESERVOIR FOR ROUNDING MECANISIM MACHINES BUILT IN 1999 AND EARLIER Add oil to the machine before beginning operation The factory has provided the right amount and type of oil with the machine see paragraph 4 in the manual If the oil container that came with the machine can not be located or is missing use 2 Qts Of SAE 40 motor oil Do not use multigrade oil it will foam and spill from the reservoir e Remove the front and rear plastic head covers S009 then remove the disconnecting pin 8036 and tilt the machine head assembly to one side e n the center of the rounding table 8042 is a large slotted flathead screw remove it by turning counterclockwise with large screwdriver e Pour the oil into the reservoir through the hole it is advisable to use a small funnel e Take the large slotted flathead screw and insert in the hole fasten it with the screwdriver turning it clockwise until seated firmly e Return the machine head assembly back to the working position Insert the disconnecting pin through the pillow block and arch and install the front and rear plastic covers MACHINES BUILT IN 2000 AND LATER Add oil to the machine before beginning operation The factory has provided the right amount and type of oil with the machine see paragraph 4 in the manual If the oil container that came with t2. B Yj SW i sof 1 gui RC IS 9 p IL i lt E c gt 8 wht View 16 SIDEVIEW HEAD ASSEMBLY A FRONT VIEW HEAD ASSEMBLY B el kippen f AANA 33 Z OB OI 2 lt S N ton w 81 gt 1 47 cA s Eu uro a hu E E 31 up position without plate Vorderansicht front view diese Schrauben niemals l sen never loosen these screws i Mora E data 8 SS 7 d 2 P Ws Top View STI SQUARE HEAD DRAWING ee gr ww changing the knife change the knife out bolt S 036 turn over 777 front view 7 27 72 S knife to block and ighten loose the hexagon screw 5 073 GA LAS SSDS S 036 S 113 5 007 lockpin inserted _ frame is fixed change of frame tura up yoke 8 113 to the end uM 5 010 18 piLot Lights manual motor starter elecirical supply pai IET me 1 EATES Schattplan diagramm KARL SCHMIDT GMBH foetal Mons ecke 3104 Aifeid Tel 08141 84271 ELA 10 aAnderung Dotum Name 31046 Alfeld Tel
3. e lf itis clean remove the dough entrapment ring see paragraph 15 e Placea sheet of paper on top of the plate parchment paper or newspaper e a Bring down the head of the machine and release the knives e b Pull gently on the paper you should be able to pull it out without tearing C If you tear the paper or are unable to pull it out you have to raise the blades to do this e d Release the locknut on the adjustment screw 5037 that stops the handle on the way down e urn the screw counterclockwise one full turn then repeat steps a b c d until the paper slides out e Fasten the locknut on the adjustment screw 5037 clockwise e Install dough entrapment ring 15 REMOVING THE DOUGH ENTRAPMENT RING 5007 e Pull down the pressing lever 5030 keep it down by holding it under your armpit and now grab the dough entrapment ring with hands one in the front and one in the back e Turn the ring clockwise until the slots on the top of the ring line up with the holding brackets 8081 now release the pressing lever to the up position The ring can now be removed from the machine e Important The dough entrapment ring must be cleaned daily after use Apply margarine or butter as a sanitary lubricant e Place the clean ring back on the rounding plate with the slots on the top of the ring lining up with the holding brackets Slowly pull down the pressing lever until the holding bracket
4. counterclockwise If this is not the case the machine will not function properly have an electrician reverse the rotation of the electric motor WARNING The rounding table 5042 is secured to the base of the machine DO NOT TRY TO LIFT OR REMOVE IT Serious damage to the rounding mechanism will result Only qualified service people are to remove the rounding table 7 CLEANING FIRST START UP e The machine is shipped with a light protective grease in the head assembly to avoid oxidation during transit e Remove the front and rear plastic covers 5009 and the dough ring 5007 please read paragraph 14 then remove the disconnecting pin 5036 and tilt the machine head to one side e Clean the grease from the machine head and rounding table using paper towels or a soft cloth e Bring the machine head back to its original position install the disconnecting pin dough ring and plastic head covers e Even though you now have cleaned the product zone use the first two or three batches of dough to do the final cleaning see paragraph 9 8 CHOOSING THE SETTINGS e he adjustment screw 5032 sets the height of the rounding chamber of each dough piece If the adjustment Screw is in the up position turn counterclockwise it will accommodate a large piece of dough whereas in its down position low numbers it will accommodate a small weight e For example Setting 2 may handle approximately 2 to 3 pounds of
5. 026 S 027 S 028 S 029 S 030 S 031 5 032 5 033 S 034 S 035 S 036 S 037 S 038 S 039 S 040 S 040A S 041 042 043 045 046 S 047 S 048 S 049 S 050 S 051 S 052 054 S 055 Screw Arch Gear Segment Gear Bar Pressure Arm Segment Bolt Adjusting Screw Pull Spring Screw Pillow Block Disconnecting Pin Adjusting Screw Roller Bearing Angle Lift Bushing Drive Assy Bearing Housing Pressure Plate Ball Bearing V Belt Pulley V Belt Pulley Motor Collar Slide Bar Bushing Molding Lever Assy Flange Bearing Knob Pull Spring Self Aligning Bearing S 056 S 057 059 S 060 S 062 5 063 S 066 S 067 S 068 S 069 S 070 S 071 5 073 5 075 5 076 5 077 5 078 5 079 S 080 S 081 S 082 S 3 S 084 S 086 S 087 S 088 S 089 S 090 S 091 S 092 S 096 S 099 S 101 S 102 S 104 S 105 Q99 113 Q003001 0001501 0001001 0003002 0001502 0001002 0003603 0001803 0001203 09000903 0000603 0000303 Bearing Housing connecting Arm Pin Connecting Rod Oil Drain Plug Oil Filler Cap Moulding Plate Pin Pin Knob V Belt Motor Sleeve Spring Guide End Stop Shoulder Bolt Pull Spring Spring Stud Guide Hook Screw Cross Piece Guide Pin Vertical Guide Casting Housing S
6. 11 30 Cross Piece Type 10 25 Cross Piece Type 9 20 2 36 Please look at your Machine Type Label before ordering 13 FRONT VIEW M md rie P NS 2 Y N N 3 HAN 5 AS S AN n Etro E TE a irm 2 S N 7 dg ME x i x EN Hem i LN WL we SEE A ONERI it REAR SS H lt lt 8 eae ee z i iw UE SS d pep NN 2 bi Ss Es Hu i VS LETT Es E 7 N mese E TE 1 22 N LK S ir i 5 3 AST e k kap u__aaa ___s__s _ t ptbh 14 SIDE VIEW Ls _ d de 5 SS TORNA c ES m RIES NONO A x as 7 IT ES na aa LEAD AAD m a 15 FRONT VIEW HEAD ASSEMBLY A Le e e 9 JOK 9 2 T T JF o E
7. paper towels e Never spray water on the machine with a hose or pressure washer because the frame and the various moving parts are made of cast iron also water will accumulate in the inside of the machine since it is not sealed e Important The knives should be cleaned daily see paragraph 7 e Dough accumulation and or insufficient cleaning will result in broken springs due to excessive friction between parts 17 PROCEDURE TO DETERMINE MODEL OF THE DIVIDER ROUNDER e Measure the distance A center to center of the disconnecting pins S036 as indicated in drawing 1 e If A 19 the machine is a model 2 36 e IfA 21 1 the machine is a model 5 18 or larger e Measure the inside diameter of the dough entrapment ring B as indicated in drawing 2 e f B 14 3 8 the machine is model E2 36 or 9 e B 1415 16 The machine is a model 10 e f B 1515 16 The machine is model 11 or larger e Finally count the number of divisions as in drawing 3 DRAWING 1 DRAWING 3 Divisions 15 20 30 36 50 18 ORDERING REPLACEMENT PARTS e Have the serial number and machine model available when gt ordering parts Compare the damaged part with the diagram and parts list supplied in this manual to determine the item number This will expedite the processing of the order and avoid the shipping of wrong parts e Call your local service agent dealer E
8. 05181 84220 Trouble Shooting ERIKA Semiautomatic Bun Divider Rounders 1 Dough Pieces Do Not Round Rounding chamber 1 too 0 Adjust screw 32 clockwise e Knives do not cut through dough Adjust screw 35 clockwise e Wrong rounding plate Check the number on your rounding plate to make sure it is the right one for the machine 2 Rounded Dough Pieces Have Nipples e Rounding chamber is too small Adjust screw 32 counterclockwise Check spring 33 to make sure that it pulls back the dividing head to molding space stop at bottom of part 32 3 Machine Does Not Run e Check electrical power supply e Reset motor starter by pressing stop and start button e Check V belt For any additional information please contact the closest service agency or call 1 800 682 8203 20
9. 75 KW 1 PH 15 NE Sound levels LwA 8 LpAeq 66dB DIN 45635 part 1 sec 7 2 part 29 sec 7 2 part 1 sec 3 17 To ensure proper use and to avoid accidents it is imperative to read the entire instruction manual prior to use of this machine 1 CAUTION Please read and familiarize yourself with the safety instructions contained this manual and the labels attached to the machine This shall be done before you operate clean or service the machine It is the purchaser s responsibility to make sure that the operators of this machine are aware of the contents of this manual It is also the responsibility of the purchaser to translate this manual in any other language for non English speaking operators 2 OWNER S RESPONSIBILITIES e The owner of this machine and the supervisory personnel shall read and follow the instructions contained in this manual e Make sure that this manual is readily available for the operators of this machine e the operators shall be properly trained and be aware of all the safety features of the machine and they shall be properly supervised while operating this machine e sure that the machine is installed conforming to all applicable codes and regulations local state and federal including OSHA regulations and electrical codes e All the warning labels and decals have to be visible at all times e The instruction manual fo
10. Cover Rear Type 2 36 Cover Rear Square Type 9 20 10 25 11 30 Adjusting Screw Type 9 20 2 36 Adjusting Screw Type 10 25 11 30 Flange Type 10 25 11 30 Flange Type 2 36 9 20 Piston w Knifehead Assy Type 11 30 Piston w Knifehead Assy Type 10 25 Piston w Knifehead Assy Type 9 20 2 36 Piston w Knifehead Assy Type 7 70 Piston w Knifehead Assy Type 6 150 Piston w Knifehead Assy Type 5 18 Piston w Knifehead Assy Type 4 40 Piston w Knifehead Assy Type 11 30 Arch Round Type 10 25 11 30 Arch Round Type 9 20 Arch Type 2 36 Arch Type 10 25 11 30 Arch Type 9 20 Gear Bar Type 4 40 6 150 Gear Bar Type 10 25 11 30 Gear Bar Type 2 36 9 20 Adjusting Screw Type 10 25 11 30 Adjusting Screw Type 2 36 9 20 Pillow Block Type 9 20 10 25 11 30 2 36 Pressure Plate Type 9 20 10 25 11 30 2 36 Moulding Plate Type 10 25 36 Parts 336 Moulding Plate Type 11 30 36 Parts 46 Moulding Plate Type 2 36 36 Parts 26 Moulding Plate Type 4 40 30 Parts 45 Moulding Plate Type 5 18 50 Parts 50 Moulding Plate Type 6 150 15 Parts 415 Moulding Plate Type 7 70 20 Parts 420 Moulding Plate Type 9 20 36 Parts 326 Moulding Plate Type 3 30 30 Parts 35 Moulding Plate Type 2 25 30 Parts 25 Moulding Plare Type 8 250 7 Parts 47 Single Phase Motor 0 55 kw Hook Screw Type 11 30 Hook Screw Type 9 20 10 25 2 36 Cross Piece Type
11. RIKA RECORD LLC at 1 800 682 8203 outside the USA 1 973 614 8500 Fax 1 973 614 8503 e You may also contact us by E mail max erikarecord com bob erikarescord com Removable Head Semiautomatic RH Divider Rounder Machines REMOVAL OF THE PISTON KNIFE HEAD ASSEMBLY p SERE SO Remove front and back covers Remove dough entrapment ring 5007 Insert 2 rounding plates 5066 on top of the pressure plate 5042 Lower the pressure handle 5030 all the way Loosen the 2 hexagonal bolts 5023 completely use a 22 mm wrench Insert an Allen wrench 6mm along the groove on top of the head picture 1 lock the wrench in the screw head NOT VISIBLE see picture 2 A and picture 2 B turn counterclockwise 3 or 4 turns Raise the pressure handle 5030 all the way to the top position Remove the piston knife assembly 5025 from the machine Wash and clean the piston knife assembly thoroughly in a pan washer or sink INSTALLATION OF THE PISTON KNIFE ASSEMBLY 1 Insert 1 rounding plate 8066 and the white installation plate which is marked with a single circle and numbered marks on top of the pressure plate 8042 The white installation plate has to be on top Place the clean piston knife assembly on top of the rounding plates The markings on the piston knife head assembly must line up with the corresponding number on the white plate 020 1 1 2 2 3 3 Carefully lower the pressure handl
12. achine e his is dangerous because the unit is top heavy and the operator could easily topple the unit over while pulling the handle 4 FILL OIL RESERVOIR Please refer to page 2 of this manual for detailed instructions for first use e Addoil to the machine before putting it in operation The factory has provided the right amount and type of oil with the machine see paragraph 3 e The filler plug is located at the rear right hand side of the machine it is a black hexagonal plastic plug e Remove by turning counterclockwise it is advisable to use a small funnel to pour the oil in the reservoir e Ifthe oil is missing use 2 of SAE 40 weight motor oil e Once the oil has been poured in the reservoir the machine is lubricated for life there is no need to replace or change the oll 5 ELECTRICAL Unless stated otherwise the machine has a 190 230 volt 3 phase 60 cycle electric motor Make sure the machine is connected to the correct voltage This information is printed on the machine identification label located on the base next to the power cord connector Only a qualified electrician is to connect the machine to the power source 6 INITIAL START UP e The motoris protected by an overload device part of the manual starter when running the machine for the first time make sure the rounding table 5042 rotates in the right direction check arrow on the front of the unit the rounding table has to turn
13. aled piece of dough onto the red plastic rounding plate 5066 with the moist side pressing against the plate e Spread the dough evenly to the outmost circle of rings so that it covers approximately the inner half of the outer circles Only apply some dusting flour on top of the dough e Never use dusting flour between the dough and the rounding plate e Insert the plate with the dough in the machine and make sure that the plate is properly seated on its locating peg e sure that there are no scraps on the bottom of the plastic plate or on top of the rounding table since this will damage the knives or the red plastic rounding plate e Once the red rounding plate has been properly placed pull down the pressure lever 8030 and compress the dough evenly by pushing down on the lever as much as you can e Itis easier to push down in short strokes several times e Release the pressure lever somewhat and press the cutting lever 5010 to the right Now push the pressure lever 5030 all the way to its end position to cut the dough into pieces e Still holding the pressure lever 8030 down move the rounding lever 8050 progressively to the left this will start the rounding process e Keep the rounding lever engaged from three to five seconds depending of the type of dough e Release the rounding lever to Its position raise the pressure arm to the top up position remove the plastic roundin
14. dough whereas setting 7 may handle approximately 5 pounds of dough on a model 9 20 7 5 pounds on a model 10 25 and up to 9 pounds on a model 11 30 If the operator does not choose the right setting he will not get a well rounded product e The dough pieces will be flat rather than round indicating that there is too much molding space and therefore the adjustment screw has to be turned clockwise for the next batch e On the other hand if the rounded pieces of dough show a nipple in the top center it would indicate that the rounding chamber is too low and the adjustment screw has to be turned counterclockwise to correct this problem e 115 best to retry after giving one or two full turns to the adjustment screw Once the seiting is correct note itona piece of paper for future reference e Please also remember that settings will differ from one type of dough to another 9 OPERATION OF THE MACHINE e he first batch of dough is to be used to do the final cleaning of the machine Keep using the same dough several times before going to the next piece Continue this operation until you no longer see any discoloration of the dough and the product zone in the machine is completely clean e piece of the dough first has to be weighed within the total weight parameters of the machine See page 3 of this manual for the weight ranges They are approximate since they depend on the dough type and handling Place the sc
15. e 5030 all the way making sure all the marks on the parts line up correctly Hold the pressure arm under your armpit Tighten the 2 hexagonal bolts 5023 firmly use a 22 mm Wrench Press down firmly on the pressure handle 8030 so as to seat the knives cross piece S082 in the gear bar 5029 Insert the Allen wrench 6mm along the groove on the top of the piston knife assembly picture 3 Lock in the screw head turn clockwise until it is tight picture 4 Raise the handle 5030 all the way to the top now lower and raise the head assembly 2 or 3 times releasing the knives each time by pressing the lever 8010 when in the low position Check Allen screw Step 6 make sure it is tight CARE MUST BE TAKEN THAT THE GEAR 5029 IS FULLY SEATED ON THE CROSS PIECE 5082 OTHERWISE SCRATCHES OR CUTS WILL BE MADE ON THE SURFACE OF THE ROUNDING PLATES 10 Remove the 2 plates inserted in step 1 11 Install the dough entrapment ring 8007 on the piston knife head assembly 12 Install the front and back safety covers 5009 10 Insert SH Page Photo 2 B Photo 3 Photo 4 11 Spare Part List Stop Latch Latch Pivot Fork Casting w Curve Ring Guide Pull Spring Dough Ring Arch for S 004 Cover Front Rear Cutting Arm Bearing Cover Pin Counter Weight Latch Bow Straight Pin Adjusting Screw Pin Pin Connection Bar Pin Snap Ring Pin Piston w knife head ass 55
16. g plate from the machine e Checkthe quality of the finished pieces and if necessary make adjustments as indicated in paragraph 9 10 DIVIDING ONLY e Insert one red rounding plate 8066 face down as a base on the rounding table 5042 e Prepare dough on another plate as described in paragraph 9 remember moist side down e Dust with flour only the top side of the dough Place the plate with the dough on top of the rounding plate inserted face down in the machine e Without running the motor press and divide the dough as indicated in paragraph 9 11 AND REPAIRS e The machine has to be inspected on a regular basis and maintenance performed as needed e Any repairs to be done by authorized service personnel only and only original spare parts should be used e The use of non approved spare parts may void the manufacturers warranty 12 ADJUSTMENT OF THE V BELTS e n time the V belts located in the base of the machine will wear and stretch e To adjust them loosen the motor bolts move the motor on its railing until the belts are tight see paragraph 13 tighten the bolts again 13 REPLACEMENT THE V BELTS e Disconnect electrical power from the machine e Remove the left side cover from the machine base e Release spring 8054 completely and disconnect from the frame e Tap out beveled S061 from the bottom up and remove e Pull and tur
17. he machine can not be located or is missing use 2 Qts Of SAE 40 motor oil Do not use multigrade oil it will foam and spill from the reservoir e The filler plug is located on the top rear right hand side of the base of the machine it is a black hexagonal plastic plug e Remove the plug by turning it counterclockwise Then pour the into the opening it is advisable to use a small funnel to pour the oil into the reservoir e Take the black hexagonal plastic plug and insert it in the hole fasten it by turning it clockwise Only hand tighten DISCLAIMER The purchaser is responsible for the proper installation and operation of the machine Should this equipment be operated without oil it shall be considered abuse or misuse of the equipment Erika Record LLC will not honor any warranty for parts and or labor For additional information please contact Erika Record LLC 37 Atlantic Way Clifton NJ 07012 Tel 1 800 682 8203 Fax 973 664 1752 Technical Information Name ERIKA RECORD Semi automatic machine to divide and to round dough pieces of the same size TOTAL WEIGHT MACHINE SHIPPING RANGE NET WEIGHT WEIGHT IN LE C i 8 250 6 150 These weights are not absolute they are approximate since they depend on the dough type and handling Dimensional requirements for the machine installed 25 W 47 D 84 H Serial No Year of manufacture Electrical power requirements 0 55 KW 3 PH 0
18. n lever 5050 until assembly S050 58 is free e Loosen the 4 bolts that hold the motor 5071 to the motor mounts S092 and slide the motor until the 3 V belts 5070 are loose e Remove the old V belts one ata time and replace with new ones e Slide the motor until the 3 new V belts are tight when pushing against the new belts with your finger you should get a 4 deflection if you get less damage to the motor bearings will be the result if you have too much play the belts will slip e Re tighten the 4 bolts that hold the motor to the machine frame e Push and turn lever S050 and insert assembly 5058 50 e Insert beveled 5061 from the top into the assembly S058 50 and tap gently until fully seated do not force pin or rivet it just tap gently e Insert spring 5054 and tighten until the lever 5050 moves freely to it s resting position e Install the left side cover on the base of the machine e He connect the electrical power 12 ADJUSTMENT OF THE KNIVES The adjusting screw 5037 determines how far the knives will travel e This is accomplished by limiting the travel of the pressure lever 5030 e The clearance between the knives in their down position and the plastic rounding plate should be the thickness of a sheet of paper e Ifthe knives touch the rounding plate first make sure that no dirt or old dough sits between the plastic plate and the metal rounding table
19. pring Bolt Lock Nut Spring Support Retaining Ring Stop Pin Motor Bracket Pin Pivot Arm Arrowhead Pin Circuit Breaker Box F Circuit Breaker Pilot Light Wheel Assy Roller transport Knife 30 pcs f Q1 Knife 15 pcs f Q1 Knife 10 pcs f Q1 Knife 30 pcs f Q2 Knife 15 pcs f Q2 Knife 10 pcs f Q2 Knife 36 pcs f Knife 18 pcs f Q3 Knife 12 pcs f Q3 Knife 9 pcs f Q3 Knife 6 pcs f Q3 Knife 3 pcs f Q3 Specifications for different types of Semiautomatic machines o 005A o 005B o 007A o 007B o 007C S 007D S 009A S 009B S 009C S 009D S 009E S 009F o 016A o 016B o 024A o 024B o 025A o 025B o 025C o 0250 S 025E o 025F o 025G o 0251 o 027A o 027 o 027C o 0270 S 027E o 029A o 029B o 029C o 032A o 032B o 035A o 042A o 066 1 o 066 2 o 066 3 o 066 4 o 066 5 o 066 6 o 066 7 o 066 8 o 066 9 o 066 10 o 066 11 o 071A o 081 o 081B o 082A o 082B o 082C Ring Guide Type 10 25 11 30 Ring Guide Type 2 36 9 20 Dough Ring Type 11 30 Dough Ring Type 5 18 Dough Ring Type 2 36 9 20 Dough Ring Type 10 25 Cover Front round Type 9 20 10 25 11 30 Cover Front Square Type 9 20 10 25 11 30 Cover Front Type 2 36 Cover Rear Round Type 9 20 10 25 11 30
20. r the operation of this machine shall be kept in a safe place next to the machine 3 INSTALLATION e After removing the sides of the wooden crate the machine has to be removed from the wooden pallet to which it is bolted with four bolts for safe transportation e Cut open the plastic sleeve in which the machine is packaged to avoid moisture problems in transit e Remove the base cover that has a yellow label indicating the storage of an oil container in the base e Remove the oil container e Remove the four nuts that hold the machine to the wooden pallet e Now drive the bolts through the wood with a hammer e Gently remove the strings and the wood piece that holds the rounding plates in place e Geta forklift truck or 2 or 3 helpers to remove the machine from the pallet e NEVER attempt to remove the machine from the pallet on your own e CAUTION Remove the pressure lever 8030 which is attached to the rounding lever 8050 machine has to be placed on a floor that is level with sufficient space around for a safe and efficient operation e he machine has to be bolted to the floor with appropriate anchors and the gap between the floor and the base has to be sealed to prevent water flour etc from entering the base We recommend the use of silicone caulking Unless the machine has been fitted with a set of wheels provided by the factory e NEVER install off the shelf type casters under the m
21. s drop through the slots in the ring e Turn the ring counterclockwise until the end stop seats against the holding bracket on the right side of the machine e Caution NEVER use metal scrappers or sharp objects to clean the ring If the ring is Teflon coated it should only be cleaned with a cloth or paper towels 16 CLEANING OF THE MACHINE e The rounding table S042 is made of steel and should be cleaned with a dry cloth only Do not use waiter e The rounding plates 5066 which are made out of plastic should be cleaned with a soft nylon brush and warm water only e Never try to clean them in a pan washer or dry them in an oven this will cause the plates to warp and later damage the knives in the rounding head e The cutting knives installed in the piston knife assembly S025 should be cleaned daily with a soft dry cloth or soft plastic brush To do this first remove the dough entrapment ring see paragraph 15 e The entire head assembly is Anodized never use metal scrappers steel wool or sharp objects of any kind to clean or remove dough or flour that may accumulate The use of compressed air is acceptable e The base of the machine and the plastic covers 5009 of the piston knife assembly should be cleaned daily with a dry cloth or a soft plastic brush heavy stains or caked on dough should be softened with any household window cleaner plastic spray bottle and wiped clean with a dry cloth or
Download Pdf Manuals
Related Search