DUAL GAUGE DX Series USER`S MANUAL
Contents
1. A WARNING these warnings may result in A CAUTION may cause injury to persons damage the the injury or death of people product and other things Do not work in areas where there is excessive This product is for DC12V cars exhaust Installation cannot be carried out on cars with other voltage batteries Due to vehicle exhaust emission poisoning or fire may Just after installation do not exert any strong force on the product result in a damage to humans When double sided tape is used for an installation be warned that when hot the Do not crush the cable tape temporarily losses adhesiveness Please be careful that the cable does not get crushed by Do Not Use Chemical Cleansers the seat rail or car door steel plate nor cut by any sharp steel plate as this may cause a poor connection or an electric short leading to fire or other danger Do not operate while driving Operating or checking the display during driving may cause If the unit gets dirty please wipe with a soft cloth to remove any dirt Do not use chemical cleansers such as thinner benzene or alcohol Do not install the product in any place subject to high tempera ture or any place where water may be splashed an accident please use with the utmost consideration for Make sure to replace all screws and parts to their original place safety Do not install the product in a place where it will cause distrac Please securely fasten the product and be sure tion to sto2. The third place from the left shows Celsius 100 150 C Numerical Value Only Reset the Peak Value Only the peak value on display will be reset This will return to the Real time Display for the currently displayed mode for 3 Seconds For Boost Vacuum RPM Water Temperature and Oil Temperature the high will be shown and for Voltage the low will be displayed If you wish to check the loss of voltage upon operation of the starter turn the key to the ON Troubleshooting position and after the digital display comes on operate the starter Possible Causes Possible Solutions Does not work with Engine start Poor connection of Gauge cable 7 pin Connector Jand OBD Connector Please reconfirm whether wiring and connections are correct or not model The unit has been installed into an incompatible car Please check the Fitting List switch was set to OFF or car battery was chan OBD Connector was connected when the key Connect again OBD Connector when the key ged switch is set to ON engine start Upon starting up the unit will start in the newly changed display Because after changing displays if the car s engine is turned off within 3 seconds the new setting will not be stored make sure to wait at least 3 seconds before turning the engine off Before the opening demo starts the needle briefly mo
3. only after installation the unit must communicate the car and hence it may take approximately 1 minute for the display to come on From the second time the display will take approximately 10 seconds to appear Same for reconnecting the OBD Connector Reference Notes about using the OBD Connector Make sure to grip the distended portions when pulling it out or inserting it A CAUTION Do not pull on the wires when trying to remove the connector the wires may If you unable to get a grip on the distended portions With some car models it may ee A be difficult to get 4 _ a good grip on a R the connector In such case pull out the connector by pulling on the 2 About Using OBD Products in Combination If you wish to use DUAL GAUGE in combination with products in our 3 drive Series FLAT or COMPACT PROGAUGE the OBD2 Wiring Kit OBD EH sold separately 3 200 makes installation a snap For more details about using combinations of products see here become disconnected end of the Connecting Oil Sensor To display Oil temperature you must purchase Temperature sensor DTS 3 800 which is sold separately Depending on the installation you may need a sensor adaptor sensor connector 1 8 PT sold separately Oil Drain Hole Installation Sensor adapter for drain hole sold separately a emperane sensor 6 CA Sold separately ee aes White tape dra
4. value Opening Demo When the key is turned ON the needle will move to the extreme left several times for searching position Then it will move to the maximum value and finally to reading for current measurement item Due to analyzation time for the car data transmission it may take up to a few seconds from engine start before opening demo Switching The Display Turning off the Display Due to analyzation time for the car data transmission the illumination may remain on for up to 3 minutes even after the engine has been turned off this is normal and no effect on the vehicle performance Switching The Digital Display Press switch to change the multi digital display ater Temp Oil Temp Voltage 1 Not displayed without temperature sensor 2 For some car models the voltage cannot be displayed or will appear For details see the Fitting List Water Temperature Oil Temperature Reading the Display 35 1 C in operation e P ue ae aapa E i 5 CET 30es7 013 3 decimal point is lightning Display and Reset the Peak Value Peak Value Display Real time Display 0 0 5 BOOST O 0043 BOOST O 1008s A 1 0 vua cause yg AT Blinking 1 0 ua cauoe With no operation 5 Seconds Peak readings are reset when the key is turned OFF The first place on the left shows minus 0 99 C
5. SOivor DXB DXV DXT DXT H As of October 2014 No 5 One Type Analog Display coupled with Multi Digital Display USER S MANUAL DUAL GAUGE Easy Installation Thank you for purchasing this PIVOT product Please read this manual carefully and keep it for future BOOST DIGITAL reference VACUUM DIGITAL D X V if this product is given to another user make sure to include this User s Manual RPM DIGITAL RPM DIGITAL For Hybrid cars Contents Please check the contents of the package Contents WARNING CAUTION eee 1 Features Peeeee eee reer errr errr eee eee ee eee eee eee eee 2 Part Names eOeeeeee eee eer errr eee ee eee eee eee ee eee ee 2 Displays of each ploducis SARS 2 Unit Gauge Adjustable Connecting The Wires 0777717115 2 3 50x22x70 D mm Cable OBD Connector Stand Installing The Product oeeeeeeeeereses 3 and fuse 3A Basic Operation Pree eeereree eee rere eee eee eee eee ey 4 gt Switching The Display eeeeee eee eer eer errr reer 4 Troubleshooting ETET TE ET 4 Zip Ties Allen Double sided Cushion Large x 2 User s Manual Wrench Tape Tape Small x 5 This Book 1 The display will not be proper if the ECU being used is not the standard one or if a sub computer is being used even in compatible car models 2 Cannot be used in combination with other company s products that use Diagnostic Monitoring Connectors Improper use or disregard of Improper use or disregard of these warnings
6. in packing Oil pan drain hole http pivotjp com obd e When using the DUAL GAUGE with products mentioned above they can only be used together in compatible model vehicles for both products Oil Element Installation Temperature sensor sold separately White tape Ts to prevent leakage Engine oil element PT For cars chassis that are low to the ground or in cases where road conditions may be poor please do not use this type of installation It may lead the sensor to bump against the ground and break or be damaged to prevent leakage WARNING connection Leif Oil element ay Sensor adapter sold separately Installing The Product Installation with the Adjustable Stand Fasten using the double sided tape On top of the steering column cover or dashboard Slightly loosen the Hexagonal bolt and install the gauge into the Adjustable Stand Adjustable _ lt Stand Hexagonal bolt Mount into the Panel Wrap the cushion tape around the base of the meter Press into the 60 mm hole in the panel Fasten using the double sided tape Clean the surface removing all oil and dust Double sided ee Included re Clean to remove oil and dust Please be sure about where you wish to install the meter as it is not advisable to reuse double sided tape After deciding the position and angle of the meter face fasten the Hexagonal bolt on both sides to
7. re bundle away all wires with tape etc Do not in any manner process take apart or make changes to It is very dangerous to pull tangled wires by force or allow this product tangled wires to interfere with driving Features Each of our Dual Gauges offer one type of analog display coupled with a multi digital display in one smart looking unit thus saving not only space but money Part Names E Analog Display EJ Needle EJ Switch Display one type of data Shows the current values and peak value Use to change modes of digital display and reset the peak value Ed Digital Display E illumination night illumination Display switches between types Normally illuminated when on display Analog Display Dial White Needle Red Digital Display Red DXB DXV DXT Green DXT H Displays of each Product Easy to Install Coupler Connection Models The DX Series models provide easy installation by simply connecting to the diagnostic monitoring connector this means being able to use the gauge without any extra necessary work 0 5 10 Sivor DUAL GAUGE 77 1 5 i 1 0 2 BOOST x100kPa Display and Product Number DXB DXV DXT DXT H Analog Display Display Range BOOST 100 154 kPa VACUUM 100 0 kPa RPM 0 9000 rpm RPM 0 7000 rpm Digital Display Display Range Water Temperat
8. secure I Hexagonal bolt It is possible to install the Adjustable Stand in the reverse direction Normal Reverse direction Meter Dimensions unit mm 15 30 abs a If you wish to fasten the unit to the A pillar or column cover please purchase and use the separately sold meter holder which gives you installation a clean natural look For mounting to the A pillar or other slanted surface it is necessary to use Cushion lace Panel screws e ape N P 260 Mater Hood 60 for 060 T MH6 U Multi Purpose Type 2 980 y MH6 C Processing Kit 2 980 Meter hood XG Installing The Unit Example of Installation Fastening When Fastenings to As shown in the right diagram fasten the unit into positions not usually affected by water Under the steering column cover L BNO t pad On the back side gt of the under cover On the inside of the driver s door a xX te PN not insta to Flat Space a Cable or Pipe Zip tie Large Il into low positions Double sided tape Included Through holes Clean to Ra remove Pa Thick cable oil and dust or pipe 3 4 Basic Operation Key Switch ON Engine start Opening Demo Display Each Mode 2 3 Meter OFF Key Switch OFF Engine stop 4 The needle stops in the vicinity of lowest
9. ure and Voltage Water Temp 35 150 C Vol Oil Temperature Displayed with Sensor sold separately 35 150 C age 8 18V Connecting the Wires Key Switch ON Engine start Insert the OBD Connector to the Diagnostic Monitoring Connector Insert the 4 pin Connector to the backside of the meter _Diagnosti Insert the 5 pin Connector of Monitoring Connector Gauge Cable and 7 pin Connector from the Power Cable to the Unit 7 pin Connector lt Backside of the 4 pin Connector 5 pin Connector 1 5m 2 5m 2 pin Connector Data Placement Diagram for Diagnostic Monitoring Connector o0 O 6 T DO oC TOYOTA MAazDA W D NISSAN O SUBARU HONDA OO BO SUZUKI MITSUBISHI Q O DAIHATSU OO Temperature Sensor Sold separately For oil temperature By the accelerator pedal At the right foot of the driver seat with lid At foot of driver seat in the center At the left foot of the driver seat with lid At the right side of the center console At the right foot of the passenger seat Behind the panel by the steering with lid At the left foot of the passenger seat At the left side of the center console Panel to right of steering wheel upper part of small storage box Note that
10. ves This is due to a special characteristic of the meter and is not a malfunction The displayed values are different from the standard meter or other meters Due to the ECU information received the displayed values on this product may differ from those of standard This product s boost meter reads absolute pressure and may differ from a meter using relative pressure The key switch is set to ON Needle of Boost Vacuum shows minus value Absolute pressure sensor shows the va Example 700m above sea level Minu lue which subtracted atmospheric pressure s 8kPa The Oil Temperature displays do not change from or do not show the value with connecting the sensor breaking of wire Poor connection of Temperature sensor or Please reconfirm Temperature sensor whether wiring and connections are correct or not regulating characteristics circuitry and circuitry layout X Our products have already been recognized as our Industrial Property or are in the process of receiving Industrial Property status We plan in the near future to take all possible legal measures to protect against unfair competition from look alike products using similar designs We strictly prohibit the unlicensed use of the PIVOT trademark and the unauthorized use of PIVOT User s Manual PIVOT CORPORATION 87 3 Shimookada Okada Matsumoto shi Nagano 390 0313 JAPAN http pivotip com
Download Pdf Manuals
Related Search