Hills Wireless_Security_Alarm_DIY Kit_Prod_Manual__HiRes
Contents
1. 1 Dial the telephone number of the SIM card using your mobile phone 2 Enter your password followed by 3 Select the operations required to control the panel see Section 5 for a table of instructions Note The call will end automatically if no command is received within 30 seconds 0166_Wireless_Security_Alarm_Kit_Prod_Manual_PM1004a_R1 indd 11 27 02 2015 4 24 pr 0166_Wireless_Security_Alarm_Kit_Prod_Manual_PM1004a_R1 indd 12 12 _5 Responding to an alarm 5 Responding to an alarm If the system detects an intrusion the siren will ring out immediately and the alarm panel will send alert SMS and dial the pre stored phone numbers The user can manage the site remotely and control the system by phone when receiving the call from the alarm system Note There is no need to type the password to control the system remotely when receiving a call from the alarm system Command Function Comment Press 0 Disarms the system and turns the siren off Stops monitoring without hanging up Ends the phone call without hanging up Press x Audio monitoring f O2 O O O O O O O OO O O Press Exits control by phone call N up also exits the control by phone call 27 02 2015 4 24 pr 6 Specifications 6 1 Alarm Panel LED GSM Signal 13 6 Specifications Zone LED Signal Arm Arm Disarm LED Signal Disarm Setup Connection LED Signal Power2. Do not use detergent or other flammable materials to clean this unit Do not let your device fall on the floor Remove the battery holder cover with care 27 02 2015 4 24 pr 2 Easy Install 2 1 Insert SIM card into the alarm panel and install in desired location Your SIM card must support the 2G or 3G network 850 2100Mhz The SIM card should have SIMLOCK deactivated SIMLOCK can be deactivated using a mobile phone prior to installing the SIM card into your alarm panel 1 Insert the SIM card NOT included in the alarm panel as shown in the image below 2 Install your alarm panel to your desired location 3 Plug the adaptor into an AC power socket 4 Switch the alarm panel on 0166_Wireless_Security_Alarm_Kit_Prod_Manual_PM1004a_R1 indd 5 27 02 2015 4 24 pr 2 Easy Install 2 2 Register accessories with the alarm panel Remote Controls Motion Sensors Window Door Sensors RFID Tags and additional sirens must all be registered with the Alarm Panel prior to use To register each accessory you must first enter Registration Mode on the Alarm Panel 1 On the Alarm Panel press 1 2 The Connection LED indicator will light up to indicate connection mode Trigger connection on the accessory you wish to register via the correct method below Accessory Trigger Wireless remote control Press any button on the remote control
3. Wireless Motion sensor Press the connect button at the back of the sensor or trigger the sensor by moving in front of it Wireless window door sensor Separate the magnet from the transmitter RFID Tag Swipe the RFID tag in front of the RFID reader on the alarm panel Additional siren Contact Hills Security for further information Once you have registered all Accessories may now be installed accessories exit Registration Mode following specifications in section 6 of 1 Press the Disarm key on the this document alarm panel Additional accessories not listed above may be registered Consult the relevant accessory manual for trigger details 0166_Wireless_Security_Alarm_Kit_Prod_Manual_PM1004a_R1 indd 6 27 02 2015 4 24 pr 2 3 Download App and set your personal alarm settings Remote access control of your alarm and configuration of alarm settings may be performed from your smartphone using the Hills DIY Wireless Security App This app is available from the Apple App m Store or Google Play ru To install the App use your device to A search for Hills DIY Wireless Security E App and tap GET Enter your store in password when prompted and the App will be installed to your home screen nn Once the App is installed tap the App icon to start the app You will be guided O through registering an account for MEN yourself and connecting to your alarm system You will need to know the mobile
4. Housing material ABS plastic Operating conditions Temperature 10 C 55 C Relative humidity lt 80 non condensing Sensor dimensions L x W x H 60 x 45 x 18mm Magnet dimensions LxWxH 45 x 19 x 17 5 mm 0166_Wireless_Security_Alarm_Kit_Prod_Manual_PM1004a_R1 indd 22 6 5 RFID Tag Features The RFID tag enables you to disarm your system Register the RFID tag to the alarm system Enter Connection Mode on the alarm panel Swipe the RFID tag in front of the RFID reader on the alarm panel Design O o Specifications Dimensions 36 x 24 x 6mm 27 02 2015 4 24 pr 6 Specifications 23 6 6 SMS Operations Store Phone Numbers for IMPORTANT BEFORE USING FOR SMS notifications THE FIRST TIME Send INSERT A SIM CARD IN THE i MAKE SURE THE SIM CARD DOES NOT REQUIRE ANY PIN CODE SAVE A PHONE NUMBER FOR SMS us numbers NOTIFICATIONS 3 Only stored numbers can control and 3 configure the system ig Each SMS operation defined in this user manual will be illustrated as follows You send Copy paste then edit case sensitive The first DARK l da amp bubble is the SMS 2 067890022 command sent by 2 067890011 the user 4 067890000 The alarm panel replies gt No space i after the 1 The first grey Alarm panel s reply speech bubble is Ok the reply sent by the alarm panel The speech bubbles that follow are the dialogue between the user and the Not alarm panel S
5. Wireless DIY security alarm starter kit User guide 0166_Wireless_Security_Alarm_Kit_Prod_Manual_PM1004a_R1 indd 1 27 02 2015 4 24 pr 1 Introduction 3 VA Eee OTR CRON AR UR TST OIE ON OE Nore ET ee ee 3 Me a ET OE ao eee EA EEN NSIT EO eT PO 3 t3 Recommendations susanne serie 4 TA MAS costed eset abacus ovenea ean bunnies vita anaes es ora toevens edad eaves nando innit oa ead RG Tae 4 2 Easy Install 5 2 1 Insert SIM card into the alarm panel and install in desired location wool ceeeeesecececsetssesseseesesseeeees 5 2 2 Register accessories with the alarm panel nee 6 2 3 Download App and set your personal alarm settings uuunaeaeneneseneenenennennnnenennenennnnnnnnnnnnnnnnenennnnnnnnnnnnn 7 3 Alarm settings 8 sl Enter SetuP MOdE ee nenne 8 32 EL Setup Modern nee ee een see 8 3 3 Store phone NUMPDEerSs een 8 9 4 Delete Droemer 9 3 5 Change pass OI naia ei oes cerca ices res 9 3 6 Set Siren VOLUME nenne 9 Il Set EINST Bs lee e ea re ee ee e Relat aera 9 3 8 Set Entry and Exit delay u 9 3 9 Clear connected Sensors versenden 9 4 Control your alarm 10 4 1 Arm your system suser NtS nen einer 10 4 2 Disarm your System ee een rennen eo 10 4o Home ddan sect vente nn bhai a a Er E 10 Ar NMAC MTN een ee 10 4o Emergency 22 ee een 10 46 Makea phone Ea resten da e ne tis er ene am E CE nent ree a raaa a ea aai 11 4 7 Speed Dial 222 energie ahnen 11 4 8 Remotely control your alarm unssseesesesesesnenennnnnnenennnnen
6. Low Power Home Mode LED Signal RFID Reader Phone Call The blue LED is the Arm Disarm status indicator If the system is armed the LED is on If the system is in Home Mode the LED blinks once every second The white LED is the Setup and Connection indicator In Connection and Setup modes the LED is on The green LED at the bottom is the Power indicator If the control is properly powered the LED is on If the power of the alarm panel is too low lt 7V the LED blinks GSM signal LED indicator when there is no GSM signal or no SIM card the LED indicator will flash once every second if GSM retrieves a signal the LED indicator will flash once every 3 seconds 0166_Wireless_Security_Alarm_Kit_Prod_Manual_PM1004a_R1 indd 13 Tamper switch Speaker Battery Power holder Interface Power switch Wired Zone interface Speaker Wired sensor Power interface SIM card slot Power ON OFF 27 02 2015 4 24 pr 14 6 Specifications Specifications 0166_Wireless_Security_Alarm_Kit_Prod_Manual_PM1004a_R1 indd 14 Power supply Input AC 110 240V 50 60HZ Output DC 12V 800mA Internal battery backup 3 7V 800 mAh battery pack x 2 Internal siren 120dB Quantity of accessories supported 60 including 10 Remote Control Radio frequency 433MHZz 75 KHz 2G amp 8G frequency 2G 850 900 1800 1900MHz 3G 850 2100MHz Hous
7. Delay Time u CHE Entry delay time 0 300sec 0 Exit delay time O 300sec 0 Copy paste then edit case sensitive Entry delay time 0 300sec 10 Exit delay time 0 300sec 20 Ok Note This function will only affect sensors assigned to the Delay zone Refer to the instructions on page 28 of this manual to learn how to set up your sensor to the Delay zone This function can be used if you do not want to bring a remote control or a RFID tag with you When you arm the system the system will be armed after the delay set When you disarm the system the system will be disarmed after the delay set When arming the system you hear one beep every second to remind you to leave The beep rhythm speeds up during the last 10 seconds If an intruder is detected the alarm will be delayed accordingly 27 02 2015 4 24 pr 6 Specifications 27 Siren Volume and Ringing Time El C Siren volume 0 Mute 1 High 1 Siren ringing time 1 9min 3 Copy paste then edit case sensitive Siren volume O Mute 1 High 0 Siren ringing time 1 9min 1 Ok Change the Password n C Disarm password 4 digits 1284 Copy paste then edit case sensitive Disarm password 4 digits 8888 Ok DEFAULT PASSWORD 1234 0166_Wireless_Security_Alarm_Kit_Prod_Manual_PM1004a_R1 indd 27 Restore System to Factory Settings by SMS Send Ok The settings will be restored to default values Store
8. sensitive to cross movements than vertical movements Test A After the installation turn the sensor on After one minute of self testing oress the test button walk in the scope of detection and watch the LED indicator to make sure the sensor is working B The LED indicator blinks once when body movement is detected C Adjust the sensor angle to achieve the best detection performance 27 02 2015 4 24 pr 20 6 Specifications Specifications Power supply DC 3V AA 1 5V LR6 Batteries x 2 Static current lt 30 uA Alarm current lt 15mA Detection scope 8m 110 Transmission distance lt 80m in open area Radio frequency 433 MHz 75 KHz Housing material ABS plastic Operating conditions Temperature 10 C 55 C Relative humidity lt 80 non condensing Sensor dimensions L x W x H 107 x 53 x 32 mm Bracket dimensions L x W x H 52 x 30 x 26 5 mm 0166_Wireless_Security_Alarm_Kit_Prod_Manual_PM1004a_R1 indd 20 6 4 Wireless door window sensor Features The door window sensor can be installed on doors windows and any other objects that open and close The sensor sends signals to the alarm panel when the magnet is separated from the transmitter Thanks to the tamper switch any attempt to remove the cover of the door window will trigger the alarm 27 02 2015 4 24 pr Magnet Transmitter LED Indicator Tamper switch A23 12V Battery Zone setting LED w
9. you do not trigger any other accessory when connecting one accessory to the alarm panel e g do not stay in the detection scope of a motion sensor if it is not the one you want to connect When attempting the connection the alarm panel beeps twice Follow the instructions on page 6 of this manual to connect the remote control to the panel The remote control has not been connected to the alarm panel No response from the alarm panel following commands from the remote control Transmission distance of the remote control 80m in Remote control is too far open area from the alarm panel A signal repeater can be installed to increase the transmission distance RFID tag fails to disarm the RFID tag has not been Follow the instructions on system connected to the alarm page 22 of this manual to panel connect the RFID tag to the alarm panel 0166_Wireless_Security_Alarm_Kit_Prod_Manual_PM1004a_R1 indd 30 27 02 2015 4 24 pr Warranty 31 Hills Limited ACN 007 573 417 gives a warranty of 12 months on this product and is subject to oroof of purchase For the current warranty conditions please visit our website at hills com au or contact your place of purchase Hills provides consumers with the following warranty in relation to this Product in addition to complying with the requirements of any relevant legislation including the Competition and Consumer Act 2010 Cth in Australia and the Consumer Guarant
10. 2015 4 24 pr Mute Mode Press the Home Mode button and the Arm or Disarm button immediately after The alarm panel will not ring out when you arm or disarm your system Emergency Mode Regardless of the status of the system the alarm is triggered when the SOS button SOS is pressed on the remote control Arm the system At the same time the alarm panel sends a notification by SMS RC 01 SOS 01 being the remote control number and dials the pre stored phone numbers Press the Arm button to arm the alarm system The LED indicator lights up the alarm panel beeps once The system is armed Register in the alarm panel If an intruder is detected the siren rings Enter Connection Mode on the out The siren turns off after alarm panel Press any button on 3 minutes as per default settings In the the remote control meantime the system dials the pre stored Specifications phone numbers automatically Power supply DC 3V Disarm the system CR2025 button battery x1 Press the Disarm button to disarm the Static current 10 UA alarm system The LED indicator turns off the alarm panel beeps twice The system is disarmed Transmission distance lt 80 m in open area Press the Home Mode button on the Radio frequency 433MHz 75KHz remote control The system state LED is Housing material ABS plastic on and flashes All the sensors in regular zones are armed except those in the Home Mode zone The sen
11. MS sent by the user are in DARK GREY SMS sent by the alarm The first SMS number will receive panel are in grey SMS notifications when the system is disarmed by RFID tag 0166_Wireless_Security_Alarm_Kit_Prod_Manual_PM1004a_R1 indd 23 27 02 2015 4 24 pr 24 6 Specifications Disarm the system Settings enquiry Send Send System Disarmed AC power On System disarmed The values indicated herein above will change after having set up the system Arm the system Store phone numbers Send Send Phone numbers System armed 3 3 4 5 Home mode Copy paste then edit case sensitive Send Phone numbers 1 067890033 2 067890022 3 06789001 1 4 067890000 9 System in home mode Ok 0166_Wireless_Security_Alarm_Kit_Prod_Manual_PM1004a_R1 indd 24 27 02 2015 4 24 pr Rename zones Send 91 99 For example for zone 1 send Zones names le Copy paste then edit case sensitive Zones names 1 Entrance door sensor Ok Note Zones 1 to 9 can be renamed The name of the zone cannot consist of more than 30 Latin characters Zones 10 to 50 cannot be renamed 0166_Wireless_Security_Alarm_Kit_Prod_Manual_PM1004a_R1 indd 25 6 Specifications 25 SMS Alert for Accessory Low Battery available for two way accessories such as Motion Sensors For accessories assigned to zones that have been renamed an SMS will be sent under the format Zone number zone na
12. d phone numbers and connected accessories will also be deleted Note Only stored numbers can send the SMS to restore factory settings Hard Reset Turn the alarm panel on if the alarm panel is already on turn it off and turn it on again Press the tamper switch at the back of the alarm panel 5 times within 5 seconds after having turned it on Settings will be restored to default values Stored phone numbers and connected accessories will be cleared 27 02 2015 4 24 pr 28 6 Specifications 6 7 Assign sensors to zones Every sensor can be assigned to four different categories of zones Home Mode Zone Delay Zone Normal Zone and 24hZone To assign a sensor to a zone open its case and place its jumpers according to the drawing below Home mode zone When the system is armed in Home Mode the sensors assigned to the Home zone do not trigger an alarm It is recommend to assign motion sensors to the Home zone so that you can have your system armed in Home Mode when you are home and moving inside your home without triggering any alarm Delay zone An entry and an exit delay can be set In such case sensors assigned to the Delay Zone will not trigger an alarm during the time of delay set For example if you assign a motion sensor to the Delay zone and you set the Entry Exit Delay to 30 seconds the motion sensor will not trigger an alarm within 30 seconds after you enter your home and within 30 seconds b
13. ees Act 1993 in New Zealand the Acts except where a New Zealand consumer acquires the relevant Product for the purposes of a business 0166_Wireless_Security_Alarm_Kit_Prod_Manual_PM1004a_R1 indd 31 Our goods come with guarantees that cannot be excluded under the Australian Consumer Law You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure All expenses of claiming the warranty will be borne by the person making the claim 27 02 2015 4 24 pr User profile Retailer information Name Name Address Address Postcode Postcode Phone Phone Invoice number Email Selling date 0166_Wireless_Security_Alarm_Kit_Prod_Manual_PM1004a_R1 indd 32 27 02 2015 4 24 pr 0166_Wireless_Security_Alarm_Kit_Prod_Manual_PM1004a_R1 indd 33 27 02 2015 4 24 pr 0166_Wireless_Security_Alarm_Kit_Prod_Manual_PM1004a_R1 indd 34 27 02 2015 4 24 pr 0166_Wireless_Security_Alarm_Kit_Prod_Manual_PM1004a_R1 indd 35 27 02 2015 4 24 pr Hills Limited A B N 35 007 573 417 Issue February 2015 PM1004a HLLS 0166_Wireless_Security_Alarm_Kit_Prod_Manual_PM1004a_R1 indd 36 27 02 2015 4 24 pr
14. efore you leave so that you can leave and enter your home without triggering an alarm Refer to the instructions on page 15 or 26 of this manual to learn how to set the entry and exit delay It is recommended to assign the Door Window Sensor to the Delay zone 0166_Wireless_Security_Alarm_Kit_Prod_Manual_PM1004a_R1 indd 28 27 02 2015 4 24 pr 6 Specifications 29 Normal zone When the system is armed and the sensor is triggered the siren rings out When the system is disarmed sensors do not trigger an alarm 24h zone Regardless if the system is armed or disarmed sensors assigned to the 24h zone will trigger an alarm It is recommended to set smoke detectors gas detectors and outdoor beam sensors in the 24h zone 0166_Wireless_Security_Alarm_Kit_Prod_Manual_PM1004a_R1 indd 29 27 02 2015 4 24 pr Cause of malfunction Solution Open the battery compartment and turn the power on The alarm panel is switched off No response following interaction with the alarm panel Contact your electricity provider Backup batteries are empty Be adapter to an Electricity grid failure The alarm panel is not in Make sure the alarm panel is Connection mode in Connection mode Make sure the accessory is triggered so to send a signal to the alarm panel Accessories have not been triggered for connection The accessory has already Accessories cannot connect been connected to the alarm panel Make sure
15. enennnnnnennnnnnenennnnnnnnennnnnnenennnnnnenennnnnnenennnnnnenenen 11 5 Responding to an alarm 12 6 Specifications 13 6 Aampanel lcd ae ee eee a dade 13 60 2 Wireless nee ne 16 6 3 Wireless MMOLONS IE ee eisen 17 6 4 Wireless door window sensor nee 20 er BAD TI een 22 66 EN OI rennen errors rensende 23 6 7 Assign sensors to ZONES ae iin 28 7 FAQ 30 0166 Wireless Security Alarm Kit Prod Manual PM1004a R1 indd 2 27 02 2015 4 24 pr Thank you for purchasing the Hills Wireless Security Alarm DIY Starter Kit Please read this manual carefully to get the best use out of this product Keep this manual for future reference 1 Introduction 1 1 Box Content 1x Alarm Panel with internal siren 2x Remote Controls 1x Wireless Motion Sensor 1x Wireless Window Door Sensor 2x RFID Tags 1x AC Adaptor 2x 800 mAh Batteries 8hr in standby mode 2 x Security Warning Stickers NOTE You will need to supply your own SIM card for use with this system 0166 Wireless Security Alarm Kit Prod Manual PM1004a R1 indd 3 1 Introduction 1 2 Features Wireless alarm system Easy to install Remote access control via phone Supports up to 50 wireless sensors and associated accessories Easy registration of new accessories Built in 120dB siren to deter potential intruders Store up to 5 phone numbers and 5 SMS numbers Arm disarm and monitor remotely via phone 27 02 2015 4 24 pr 1 Introduction 1 3 Recommendatio
16. for calls from the alarm system in the event of an alert ID s 6 10 are used for SMS alert messages The first stored number is the Speed Dial Number 1 Enter Setup Mode 2 Enter ID your number do not enter the signs For example to store number 12345678 as the first SMS number enter 6 12345678 3 Exit Setup Mode 27 02 2015 4 24 pr 3 4 Delete phone numbers Individual numbers may be deleted by ID 1 Enter Setup Mode 2 Enter ID For example to delete the fourth stored SMS number enter O 3 Exit Setup Mode Alternatively you may delete ALL stored numbers 1 Enter Setup Mode 2 Enter 3 Exit Setup Mode 3 5 Change password The default system password is 1234 For security reasons it is recommended you set your own 4 digit password 1 Enter Setup Mode 2 Enter 9 password For example to set the password to 0987 enter 9 0987 3 Exit Setup Mode 3 6 Set Siren volume The alarm system siren may be set to either high 1 or mute 0 1 Enter Setup Mode 2 Enter 23 volume For example to set the volume to mute enter 23 0 3 Exit Setup Mode 0166 Wireless Security Alarm Kit Prod Manual PM1004a R1 indd 9 3 Alarm settings 3 7 Set Siren ring time Siren ring time may be set from 1 to 9 minutes 1 Enter Setup Mode 2 Enter 1 minutes For example to set the ri
17. ing material ABS plastic Operating conditions Temperature 10 C 55 C Humidity lt 80 non condensing Panel size L x W x H 200mm x 125mm x 26mm 27 02 2015 4 24 pr 6 Specifications 15 Description Operation Functions Remarks The system enters into Connection Mode after 1 beep The system enters 2 Enter Connection Mode Enter Setup Mode into Setup mode after 1 beep 9 is the time the siren Program Ringing Time K1KIK rings out in minutes Default setting of the Siren It can be set from 1 to 5 minutes 9 minutes Exit Delay Time 2 6O 60 is the delay set up by the user in Default setting no seconds It can be set from O to 300 delay 0 seconds seconds The password can be Default password Change Password x9xnew password any 4 digits code 1234 See 4 5 Store Phone 1 5 for phone num Program Phone 1 10 phone SATE _ Numbers number le in this ee 0 for SMS Delete phone Delete one of the Phone Numbers and If no number is stored Delete All Phone SMS Numbers will the system will not Numbers be cleared from the auto dial when the system alarm is triggered Clear every connected 23k0 Deactivate the siren BE Siren setup Entry Delay Time K3Kk6GOK K238 1X Activate the siren Fee The alarm panel beeps twice Setup mode has been exited Press the Disarm Exit Setup Mode button 0166 Wireless Security Alarm Kit Prod Manual PM1004a R1 indd 15 27 02
18. me Low BAT Zone 10 Bedroom PIR Low BAT For accessories assigned to zones that have not been renamed an SMS will be sent under the format Zone number Low BAT Zone 10 Low BAT SMS Alert for Accessory Tamper Alarm available for two way accessories such as Motion Sensors For accessories assigned to zones that have been renamed an SMS will be sent under the format Zone number zone name Tamper Zone 10 Bedroom PIR Tamper For accessories assigned to zones that have not been renamed an SMS will be sent under the format Zone number Tamper Zone 10 Tamper 27 02 2015 4 24 pr 26 6 Specifications Rename RFID Tag El C Rename RFID tags 4 2 3 4 Copy paste then edit case sensitive Rename RFID tags 1 Tom 2 Nurse 3 Nancy 4 David Ok Note The first SMS number will receive SMS notifications when the system is disarmed by RFID tag If the RFID tag that disarms the system has been renamed the SMS notification will be Tag 01 Tag name Disarm O1 is the number of the tag Other tags will be assigned a number based on the order of registration to the alarm panel the SMS notifications will in such case be Tag 04 Disarm 04 is the number of the tag Refer to the instructions on page 22 to learn how to register an RFID tag in the alarm panel 0166_Wireless_Security_Alarm_Kit_Prod_Manual_PM1004a_R1 indd 26 Entry and Exit
19. ng time to 7 minutes enter 1 7 3 Exit Setup Mode 3 8 Set Entry and Exit delay Entry and exit delay may be set from O to 300 seconds using ID 3 for entry and 2 for exit 1 Enter Setup Mode 2 Enter ID seconds For example to set the exit delay to 60 seconds enter 2 60 3 Exit Setup Mode 3 9 Clear connected sensors To clear ALL currently connected accessories 1 Enter Setup Mode 2 Enter 22x password Where password is the 4 digit password you set in section 3 5 3 Exit Setup Mode 27 02 2015 4 24 pr 10 Control your alarm 4 Control your alarm 4 1 Arm your system To arm your system press the Arm button on your Alarm panel remote control or App The LED indicator on the alarm panel will light up and the alarm panel will beep once 4 2 Disarm your system To disarm your system press the Disarm button on your Alarm panel remote control or App The LED indicator on the alarm panel will go out and the alarm panel will beep twice NOTE If the alarm has sounded the user must type the password and the disarm button to disarm the alarm system This operation must be completed within 15 seconds 4 3 Home mode In home mode sensors configured in the Home Mode zone are disarmed so you can move around your home Sensors in all other zones are armed To set home mode press the Home Mode button on your Alarm panel
20. ns For your safety it is recommended to follow these precautions e Do not forget to arm the alarm panel during your absence and make sure it works properly e Do not forget to lock the doors windows and other exits e Always keep your remote control with you and do not leave it visible or noticeable e To optimize the operation of the alarm system it is recommended to carefully select the location for each accessory to be installed e t is recommended to mount the sensors on a smooth wall to ensure the proper use of the tamper switch e Accessories purchased separately must be connected to the alarm panel manually e Wait until the end of the auto test before replacing the cover of the sensor e f you do not use this product for a long time remove the batteries to optimize their lifespan e Do not cross the beams of different motion sensors 1 4 Warnings 0166_Wireless_Security_Alarm_Kit_Prod_Manual_PM1004a_R1 indd 4 The alarm panel is provided with a separate battery Please dispose the used batteries responsibly Do not open the case of the alarm panel and do not repair it yourself If you encounter an issue with the product contact your supplier or an authorised technician Take care of this product and do not let water get into it as it may damage the product Place the alarm panel in a cool dry and well ventilated area Do not install sensors near heating cooling or ventilation
21. number of the SIM card installed j in your alarm panel H LLS DIY wireless security alarm NOTE Prior to controlling or configuring the alarm via the App you must program a phone number for SMS notifications Only stored numbers are allowed to control and configure the system See section 3 3 for more information 0166_Wireless_Security_Alarm_Kit_Prod_Manual_PM1004a_R1 indd 7 27 02 2015 4 24 pr 3 Alarm settings 3 Alarm settings Alarm settings may be configured directly from the alarm panel via SMS or via the App This section details direct alarm panel configuration Instructions for configuration via SMS can be found in Section 6 6 of this manual When configuring settings the alarm panel will sound the words operation completed when a change is successful 3 1 Enter Setup Mode In order to configure settings the alarm panel must be in setup mode 1 Press the key followed by the 2 key on the alarm panel 2 The Setup LED indicator will light up 3 2 Exit Setup Mode After settings have been configured you must exit setup mode 1 Press the Disarm key on the alarm panel 2 The Setup LED indicator will go out and the system will sound 2 beeps 0166 Wireless Security Alarm Kit Prod Manual PM1004a R1 indd 8 3 3 Store phone numbers Phone and SMS numbers are defined by ID ID Type of number 7 eraus rare I o msnen ID s 1 5 are used
22. one LED working When the alarm system is armed the indicator tamper switch will trigger the alarm if the case is opened Infrared sensor Antenna Infrared sensor Detects the infrared rays released by human body motion Do not touch the AA 1 5V surface Keep the surface clean LR6 When the sensor is in operation and triggered more than twice within 3 minutes it switches to standby mode to save power If no movement is detected within the next 3 minutes the sensor goes back to working mode Registering the sensor Enter Connection Mode on the alarm Connect button panel Press the connect button at the back of the motion sensor or trigger the sensor by moving in front of it 0166_Wireless_Security_Alarm_Kit_Prod_Manual_PM1004a_R1 indd 18 27 02 2015 4 24 pr 0166_Wireless_Security_Alarm_Kit_Prod_Manual_PM1004a_R1 indd 19 6 Specifications 19 Installation Avoid mounting the sensor close to windows air conditioner heater refrigerator oven Sunshine and places where the temperature changes fast or where the air stream flows frequently Top view Side view If two sensors are installed in the same detection scope adjust the location to avoid interferences and false alarms Fix the bracket on the wall with screws and attach the sensor to the bracket Adjust the bracket to change the detection distance and angle It is recommended to mount the sensor 2 2m from the ground The sensor is more
23. orking indicator LED indications Blinks once the door or window is open and the transmitter sends a signal to the alarm panel Blinks quickly Low power indication the batteries must be replaced You will be informed by SMS when the batteries are low if the door window contact is registered in the alarm panel 0166_Wireless_Security_Alarm_Kit_Prod_Manual_PM1004a_R1 indd 21 21 6 Specifications Register in the alarm panel Enter Registration Mode on the alarm panel Separate the magnet from the transmitter To check if registration is complete arm the system and separate the magnet from the transmitter again by opening the door or window on which it is installed If the siren rings out the registration is successful Installation e Open the case and remove the battery activation strip e Mount the sensor on the door and the magnet on the door frame e Make sure the magnet is placed above the transmitter e Mount the magnet max 1 cm away from the transmitter and secure the transmitter and magnet with double sided tape or screws e Avoid mounting the sensor in areas with a large amount of metal or electrical wiring such as a furnace or utility room 27 02 2015 4 24 pr 22 6 Specifications Specifications Power supply DC 12V A23 12V Battery x 1 Static current lt 30 UA Alarm current lt 15 mA Transmission distance lt 80m in open area Radio frequency 433 MHz 75 KHz
24. remote control or App The LED indicator on the alarm panel will blink once per second 0166_Wireless_Security_Alarm_Kit_Prod_Manual_PM1004a_R1 indd 10 4 4 Mute mode From the remote control you can prevent the alarm panel beeping when you arm or disarm your system Press the Home Mode button followed immediately by either the Arm or Disarm button 4 5 Emergency mode In an emergency you can trigger an alarm regardless of the status of the system Press the SOS button on the remote control or hold the SOS button on the alarm panel for 3 seconds Once activated the alarm panel will send an SMS notification in the form of RC 01 SOS where RC 01 is remote control 1 and call the pre stored phone numbers to report the SOS 27 02 2015 4 24 pr Packagecontents 11 4 6 Make a phone call The alarm panel supports phone calls In disarmed status type the telephone number and press the U key on the alarm panel Press amp or to end the call The middle white LED indicator blinks once every 2 seconds during the call If a phone call is received on the alarm panel the LED blinks once every second 4 7 Speed Dial This function is only available when the system is disarmed Press and hold the Call button amp on the alarm panel for 3 seconds the panel auto dials the first stored phone number Press the Call button amp to end the call 4 8 Remotely control your alarm
25. sors in the Home Mode zone are disarmed so that users Can move inside their home Dimensions 57 x 31 x 11 mm Operating current lt 7 mA Home Mode Operating conditions Temperature 10 C 55 C Relative Humidity lt 80 non condensing 0166_Wireless_Security_Alarm_Kit_Prod_Manual_PM1004a_R1 indd 16 27 02 2015 4 24 pr 6 Specifications 1 7 6 3 Wireless motion sensor Features The high performance wireless motion sensor boasts a digital dual core fuzzy ed logic infrared control chip with intelligent Cc analysis This technology identifies interferences created by body motion rus 5 and reduces the false alarm rate With automatic temperature compensation and anti air turoulence Ground technology it easily adapts to environmental changes Design LED indicator Detection window Bracket LED indications Blinks continuously self testing Blinks once an intruder is detected Blinks twice self testing is complete entering working mode Blinks once every 3 seconds under voltage indication the batteries must be replaced You will be informed by SMS when the batteries are low if the motion sensor is registered in the alarm panel 0166_Wireless_Security_Alarm_Kit_Prod_Manual_PM1004a_R1 indd 17 27 02 2015 4 24 pr 18 6 Specifications Usage Open the case and remove the battery activation strip Self testing will start for 30 seconds Tamper switch Alarm z
Download Pdf Manuals
Related Search