Hedge Trimmer GHT-620
Contents
1. Fe aeee HRO Read instructions carefully In accordance with essential applicable safety standards of European directi ves Class II machine Double insulation You don t need any earthed plug Denotes risk of personal injury loss of life or damage to the tool in case of non observance of the instructions in this manual Indicates electrical shock hazard Immediately unplug the plug from the mains electricity in the case that the cord gets damaged and during maintenance Wear ear and eye protection Wear protective gloves Keep bystanders away Do not expose to rain Faulty and or discarded electrical or electronic apparatus have to be collected at the appropriate recycling locations Helpline No UK Northern Ireland 0870 7323023 Rep Ireland 1800 481005 Helpline No UK Northern Ireland 0870 7323023 Rep Ireland 1800 481005 13 12 Helpline No UK Northern Ireland 0870 7323023 Rep Ireland 1800 481005 General safety instructions Attention When using electric machines always observe the safety regulations applicable in your country to reduce the risk of fire electric shock and personal injury Read the follo wing safety instructions and also the enclosed safety instructions Keep these instructions in a safe place 1 Keep work area clear Cluttered areas and benches invite injuries 2 Consider work area environment Do not expose power tools to rain Do not use power tools in damp or wet locations Keep work2. lubricating and changing accessories Inspect tool cords periodically and if damaged have repaired by authorized service facility Inspect extension cords periodically and replace if damaged Keep handles dry clean and free from oil and grease 13 Disconnect tools When not in use before servicing and when changing accessories such as blades bits and cutters 14 Remove adjusting keys and wrenches Form the habit of checking to see that keys and adjusting wrenches are removed Helpline No UK Northern Ireland 0870 7323023 Rep Ireland 1800 481005 05 06 from tool before turning it on 15 Avoid unintentional starting Do not carry plugged in tools with finger on switch Be sure switch is off when plug ging in 16 Outdoor use extension cords When tool is used outdoors use only extension cords intended for use outdoors and so marked Always use tool in conjunction with a residual circuit breaker device 17 Stay alert Watch what you are doing Use common sense Do not operate tool when you are tired 18 Check damaged parts Before further use of the tool a guard or other part that is damaged should be care fully checked to determine that it will operate properly and perform its intended functi on Check for alignment of moving parts binding of moving parts breakage of parts mounting and any other conditions that may affect its operation A guard or other part that is damaged should be properly repaired or replaced by an autho
3. 800607 52 Rotor 402014 53 Bearing 629ZZ 800629 14 Helpline No UK Northern Ireland 0870 7323023 Rep Ireland 1800 481005 HEDGE TRIMMER The numbers in the following text correspond with the pictures at page 2 Read this manual carefully before using the machine Ensure that you know how the machine works and how it should be operated Maintain the machine in accordance with the instructions and make certain that the machine functi ons correctly Store this manual and other enclosed documentation with the machine Contents 1 Machine information 2 Safety instructions 3 Operation 4 Maintenance 1 MACHINE INFORMATION Technical specifications Voltage 230 V 50 Hz Input power 620 W No load speed 1600 min Cutting length 610 mm Tool class Il Maximum cutting thickness 20 mm Weight 4 1 kg Lpa sound pressure level 91 0 dB A Lwa sound power level 104 0 dB A Outdoor noise 104 0 dB A Vibration 4 0 m s Contents of packing Main Body Blade cover Instruction manual Safety instructions Warranty card re re en M Please inspect the machine and accessories for transit damage Features Fig 1 1 Power Cable 2 ON OFF trigger 3 Power Cord Hanger Helpline No UK Northern Ireland 0870 7323023 Rep Ireland 1800 481005 03 04 ONO e Cutting Blade Safety Guard Safety Switch Transport protection Un Lock button rotating handle 2 SAFETY INSTRUCTIONS Explanation of symbols In
4. Northern Ireland 0870 7323023 Rep Ireland 1800 481005 09
5. area well lit Do not use power tools in presence of flammable liquids or gases 3 Guard against electric shock Prevent body contact with grounded surfaces e g pipes radiators refrigerators 4 Keep visitors away Visitors should be kept away from the work area at all times Do not let visitors handle the machine at any time 5 Store unused tools When not in use keep tools out of reach of children Store in a dry and secure loca tion 6 Do not force tool Do not apply undue pressure as this may affect performance and may cause damage to the machine Forcing the job also increases the potential for accidents 7 Use right tool Do not force small tools or attachments to do the job of heavy duty tool Do not use a tool for purposes not intended 8 Dress properly Always wear appropiate personal protective equipment PPE Do not wear loose clo thing or Jewellery They can be caught in moving parts Protective gloves and non skid toe protected footwear are recommended when working outdoors Wear protecti ve hair covering to contain long hair 9 Use safety glasses Also use face or dust mask when operation is dusty 10 Do not abuse cord Never carry tool by cord or yank it to disconnect it from electrical socket Keep cord from heat oil and sharp edges 11 Do not overreach Keep proper footing and balance at all times 12 Maintain tools with care Keep tools sharp and clean for better and safer performance Follow instructions for
6. for particular working condi tions e g for cutting work or for left handers e Pull the knob 8 backwards using your thumb e Rotate the handle to the new position until it jams Trimming a hedge best method Ideally a hedge should be wider at the bottom than the top This will improve light penetra tion keeping the hedge healthy If possible trim both sides of the hedge When trimming the sides of the hedge trim from the bottom upwards This will ensure there are no hedge trimmings obscuring or interfering with your cut strokes The blade should not be forced to cut too deep Cut lightly through the surface of the hedge When trimming the top of the hedge trim away from you but do not over reach It is much wiser and safer to move along and cut within your reach remaining on two feet at all times Do not let the blade come into contact with wire meshing or fencing material It could damage the material and your trimmer 4 MAINTENANCE Make sure that the machine is not live when carrying out maintenance work on the motor The machines have been designed to operate over a long period of time with a minimum of maintenance Continuous satisfactory operation depends upon proper machine care and regular cleaning Trouble shooting The following table gives checks and actions that you can perform if your machine does not operate correctly If this don t identify remedy the problem contact your service centre Helpline No UK
7. loose fitting or jewellery and ensure garments cannot come into contact with moving parts e If you have long hair tie it back safely to avoid tangling it in moving parts e Before using any power tool check first for damaged parts and if found do not use it before the part or parts have been replaced with new ones e Do not use power tools when you are tired or have been drinking alcohol e Do not force the appliance let it work at the rate for which it was intended Helpline No UK Northern Ireland 0870 7323023 Rep Ireland 1800 481005 ce DECLARATION OF CONFORMITY GB a We declare under our sole responsibility that GHT 620 is in conformity with the following standards or standardized documents EN60745 1 prEN7 745 2 15 EN55014 1 EN55014 2 EN61000 3 2 EN61000 3 3 in accordance with regulations 98 37IEC 73 23IEEC 89 336 EEC 2002 95IEC 2002 96 EC from 01 01 2007 ZWOLLE NL J A Bakker van Ingen CEO Ferm BV J Lodewijk Quality Manager Ferm Global It is our policy to continuously improve our products and we therefore reserve the right to change the product specification without prior notice Ferm BV Lingenstraat 6 8028 PM Zwolle The Netherlands Helpline No UK Northern Ireland 0870 7323023 Rep Ireland 1800 481005 11 e Machine fails to opera Power turned off e Turn power on Machine overheats Machine functions intermittently Machine does not cut Mains socket faulty Extension cab
8. warnings Regularly clean the machine housing with a soft cloth preferably after each use Keep the ventilation slots free from dust and dirt If the dirt does not come off use a soft cloth moistened with soapy water Never use solvents such as petrol alcohol ammonia water etc These solvents may damage the plastic parts Lubrication The machine requires no additional lubrication Faults Should a fault occur e g after wear of a part please contact the service address on the warranty card In the back of this manual you find an exploded view showing the parts that can be ordered Environment To prevent damage during transport the appliance is delivered in a solid packaging which consists largely of reusable material Therefore please make use of options for recycling the packaging Faulty and or discarded electrical or electronic apparatus have to be collected at the appropriate recycling locations Warranty For the conditions of warranty please refer to the separately provided warranty card Helpline No UK Northern Ireland 0870 7323023 Rep Ireland 1800 481005 A Danger The cutting elements continue to move after the motor is switch off If the cord becomes damaged during use disconnect the cord from the power supply immediately DO NOT TOUCH THE CORD BEFORE DISCONNECTING THE SUP PLY Do not use the appliance if the appliance cord or the extension cord are dama ged Keep extension cord away from cutting elemen
9. GB Subject to change G Trimm er GARDENLINE GHT 620 USER S MANUAL What your 3 Year Warranty means Great care has gone into the manufacture of this product and it should therefore provide you with years of good service when used properly In the event of product failure within its intended use over the course of the first 3 years after date of purchase we will remedy the problem as fast as possible once it has been brought to our attention In the unlikely event of such an occurrence or if you require any information about the product please contact us via our helpline support service details of which are to be found both in this manual and on the product itself This does not affect your statutory rights AFTER SALES SUPPORT UK Help Line 0870 7323023 IRELAND Help Line 1800 481005 Web Support www servotool nl Helpline No UK Northern Ireland 0870 7323023 Rep Ireland 1800 481005 Art no HGM6013 www servotool nl 0702 14 Exploded view 02 Helpline No UK Northern Ireland 0870 7323023 Rep Ireland 1800 481005 Helpline No UK Northern Ireland 0870 7323023 Rep Ireland 1800 481005 15 Spare parts list Position Description No 4 5 6 30 31 32 Switch complete 402006 8 Brake cable 402007 16 Big gear 402008 17 till 22 Excentric complete 402009 23 till 28 Blade holder complete 402010 26 Blade 402011 46 Carbon brush 402012 49 Stator 402013 50 Bearing 607ZZ
10. d blade teeth have extended points with rounded ends to reduce the chance of injury in case of accidental contact e The fixed blade is longer than the moving blade to guard against kickback should you inadvertently make contact with a wall or fence e The rear handle trigger switch 2 and front handle bar switch 6 must be operated toge ther to start the motor This ensures that both hands are used to control the trimmer e If either of the two switches is released the tool is designed to stop rapidly Using the cord grip To help secure the plug to the extension cord make a loop in the extension cord and attach it to the cord grip as shown see Fig 2 Once secure attach the cord to the plug This will prevent accidental pull out Using your hedge trimmer For your own safety and for best results read the following user advice and do not use this product for anything other than its intended purpose Switching On and Off Fig 1 e To switch the trimmer on press the safety switch 6 and the start switch 2 at the same time To switch off release one or both switches Note If you notice a slight burning smell it is nothing to worry about It is the electric brake working 08 Helpline No UK Northern Ireland 0870 7323023 Rep Ireland 1800 481005 Rotating the handle a Fig 1 The handle can be rotated in 90 steps to the machine housing This allows you to place the On Off switch in a more comfortable handling position
11. le dama ged Fuse faulty blown Air vents blocked Extension cable dama ged Machines internal wiring damaged Cutting objects too thick Blades worn Use another socket Inspect cable replace if damaged Replace fuse Unblock air vents Inspect cable replace if damaged Contact service centre See specification table for maximum cutting thickness Get blades replaced or sharpened Do not overreach while working you may lose your balance Never use this appliance without the blade guard fitted It must always remain fitted Only use spare parts and attachments supplied by Ferm Use of attachments other than those supplied or recommended by Ferm will invalidate your guarantee and could be dangerous Only use this appliance for its intended purpose trimming hedges and bushes We strongly recommend the use of an RCD Residual Current Device of not more than 30 mA at the plug socket when using this appliance Only use spare parts and attachments supplied by Ferm Use of attachments other than those supplied or recommended by Ferm will invalidate your guarantee and could be dangerous Do not allow the power cord to lay on or across sharp objects that might pierce the outer insulation Carry out a visual inspection of the power cord before use and if it is damaged have it replaced by a specialist service centre Do not use the appliance if the cord is damaged A Above all be carefull Cleaning Specific safety
12. rized service centre unless otherwise indicated elsewhere in this instructions manual Have defecti ve switches replaced by an authorized centre Do not use tool if switch does not turn on and off 19 Warning The use of any other accessory or attachment other than recommended in this opera tion instructions or the catalogue may present a risk of personal injury 20 Have your tool repaired by an expert This appliance is manufactured to very high standards and meets relevant safety regulations Repairs should only be done by a suitable qualified electrical engineer or otherwise 21 Hearing eye and hand protection should be worn PPE Specific safety instructions e Dispose of plastic bags safely they are a suffocation hazard for young children e Keep the area you are working in clean and tidy e If you are using a means of support to raise yourself off the ground ensure that it is stable and cannot topple over do not overreach at any time e Do not use power tools in the rain or wet environments e Do not use power tools where there is a risk of fire or explosion i e near flammable liquids or gases e Do not allow children into the area where you are working e Do not let children or other people touch power tools e Do not leave the power tool unattended e Store in a dry place well out of reach of children e Always use safety glasses and gloves We also recommend the use of ear protectors e Wear the right clothes not
13. ts Always ensure the guards are fitted when using the tool Check the cable for damage before starting work and replace if necessary Inspect and maintain the trimmer regularly Have the trimmer repaired only by an authorised repairer Keep your hands and feet away from the cutting area at all times Always hold the trimmer at a safe distance from the body Always wear protective goggles Always wear gloves Only use the trimmer in daylight Ensure the ventilation openings are clear of debris at all times Ensure there are no people of animals within 5 metres of your trimming area Remove the plug from the power socket before attempting any maintenance After use the tool should be stored so that the blade is not exposed Helpline No UK Northern Ireland 0870 7323023 Rep Ireland 1800 481005 07 Electrical safety Always check that the mains voltage is the same as on the type plate of the machine a gt The machine is double insulated therefore no earth connection is required Replacement of power cords or plugs Immediately dispose of old cords and plugs once they have been replaced It is dangerous to plug aloose power cord into a mains power socket Use of extension leads Only ever use approved extension leads that are suitable for the power rating of the machine The minimum core thickness is 0 75 mm Whenever using a reel extension lead always fully unroll the lead 3 OPERATION Safety features e The fixe
Download Pdf Manuals
Related Search