Natural Fires BF110V / Straight and BF120H / Relaxed
Contents
1. nnn n nnn 45 10 1 General zene AR X e ene t dte ope t a DR OR ERREUR 45 10 2 TO light ea Re eenn CLERI E Sha weber Ee ERA 46 10 3 To extingulsIrz iue cocer e er Re poet xe ne Er 46 10 3 1 When the pilot extinguishes nnn eneen e 46 10 4 Remote control version sssssssssssssse mens 47 10 4 1 Using the remote control an eere et an ih 47 10 4 2 Setting the right transmission code nun eneen eneen eneen ereen 48 10 4 3 Ch nging the batteries nn le Na 48 11 Cleaning and service instructions eee 49 12 Disposal of packaging and appliance ss sans sanss eenn 50 Appendix technical data asss sar eee er 51 4 lt lt Gfaher UK IRL 1 Introduction Note these instructions should be read carefully and retained for future reference Please leave these instructions with the user This guide is concerning the following types of appliances BF110V Straight frameless with log burner Faber false chimney breast optional BF110V Straight frameless with pebble burner Faber false chimney breast optional BF110V Straight with frame and log burner BF110V Straight with frame and pebble burner BF120H Relaxed frameless with flat fibre burner and logset BF120H Rlaxed frameless with pebble burner BF120H Relaxed with frame and flat fibre burner and logset BF120H Relaxed with frame and pebble brander Special features The frameless models of the Natural Fires feature a pate2. 1 Gfaher gt gt 11 UK IRL BF110V Straight Frameless ront view false chimney breast 12 lt lt Gfaher UK IRL BF110V Straight With frame Top View Gfaher 2213 UK IRL BF120H Relaxed Frameless Top view TIENE fe vr Mee Ee ER or muur wall Promatec Glasklem Glass clamp UKARL Make sure there is no Promatec A f sealing off the top Cross section side view of the opening muur wa Front view Opening 14 lt lt Gfaher UK IRL BF120H Relaxed Top View With frame T 9 EET TEE muur wall lt Front View Cross section side Front View Builders opening smaller than the appliance faher gt gt 15 UK IRL Operation door Opening 16 lt lt Gfaher UK IRL 3 3 Flue requirements The appliance is of the type C11 C31 The appliance will need to be supplied with the approved flue pipes and terminal it is not possible to supply your own The minimum effective height of the flue system must be 0 5 or 1 meter depending on the appliance Flue routing The terminal locations through the wall as well as through the roof A horizontal extension with elbows is allowed for a maximum of 6 meters depending on the type and situation Vertical max 12 meters Determine on the base of the table 2 and 3 depending on the type and terminal position if t
3. Make sure that both the gas control block and the main gas valve are easy accessable at all times and can be operated if necessary Specific requirements for making a false chimney breast for the BF110V Straight frameless The front opening of the false chimney breast has to be at least 460mm wide and 1100mm high measured from the underside of the floor plate Minimum distance from the glass to any of the construction parts of the false chimney breast should be at least 12 mm This is the minimum distance with which the glass can still be taken out When using a material thicker than 12mm e g 50mm thick stony material the floor plate has to be adjusted according to the indicated pattern see paragraph 3 2 for construction details and dimensions Specific requirements for a false chimney breast for the BF110V Straight with frame The wall opening has to be 620x1100 mm This is smaller than the appliance The gas control block can be mounted on either the left or right side of the floor plate depending on which side makes it easier to acces it Specific requirements for a false chimney breast for the BF120H RELAXED frameless The wall opening has to be 1050x425 mm This is smaller than the appliance The wall opening depth is 50 mm The distance between the opening and the glass should be at least 12 mm This is measured after finishing 8 lt lt Gfaher UK IRL Use 12 mm Promatec for the front of the false ch
4. F 431 0 513 656501 52 lt lt Gfaher
5. IRL 9 Safety instructions for the user 9 1 General safety instructions e These instructions should be read carefully and retained for future reference e Do not place flamable materials in the combustion chamber e Ifa gas leak is found or suspected turn off the gas supply at the meter and contact your installer or gas emergency service e Do not use the fire with a broken or damaged glass e The fire has a safety device which turns off the gas supply if there is a build up from flue gasses in the combustion room or a temporary gas cut off Wait at least 5 minutes before turning the appliance on again e Contact a qualified installer when the appliance goes off regularly The appliance has been designed for heating purposes This means that all surfaces including the glass can become very warm over 100 C An exception to this is the lower side of the door and the control buttons e Due to the newness of materials they may give off a slight smell for a period after initial lighting This is normal odours will disperse after a few hours use e Do not place curtains clothing laundry furniture or other flammable materials nearby the appliance The required minimum distance is 100 cm e Switch off the receiver of the remote control if you don t use the fire for a long time Do not let children use the remote control without supervision e Children should only use the remote control under supervision IMPORTANT A suita
6. adjusting the frame sss 27 4 7 Placing the log set with the log burner sss 28 4 8 Placing the pebbles with pebble burner sss 28 5 Installation of the flue ssccscceeeeeeecessseeeeeeeeeesnaaas 29 5 1 Connections with use of concentric duct Material 29 5 2 Connection onto an existing chimney nsv 29 5 3 Remote control iiss esce est n eR he de E X YR eda a 30 5 3 1 Installation remote control csse mme een 31 6 Commisioning functional checks eeeeeeee 33 6 1 Check pilot ignitlOri ua ee aan 33 6 2 Functional burner check cccceccee eect eee eens mn 33 6 3 Functional balanced flue check eenen nn 34 6 4 Check reference pressure and burner pressure eneen 34 7 Final check and handing over seeren 36 Gfaher bs UK IRL TT 8 Servicing ana 37 8 1 Ro tine Sservieing ns A enn a ne TREE NS daa 37 8 1 1 Cl amp aning thie glass a eben Den 37 8 1 2 Cleaning the combustion chamber and burner nennen eneen eenen 38 8 1 3 Burner tray dis assembly cece a emen 39 8 14 Gas control block d ar UEM Ne nU AREE 39 8 2 Proparie converslorn va rn sb 39 8 3 Combustion test ein Den 39 8 4 List of spare parts annen enen emen 40 User guide o aes aa WEIN RRERREIRRKAERAR RA RARE ma krais 41 9 Safety instructions for the user nn nnnnnnnnnannnnn mani 43 9 1 General safety instructions sss mnn 43 10 Controlling the appliance
7. gas you have to order a complete new propane burner unit Contact your supplier and give the serial number from the data plate 8 3 Combustion test A BS7967 combustion analysis check should be carried out using an analyser to BS7927 positioned in the flue outlet Ratio CO CO2 should be less than 0 01 within 30 minutes 100 ppm CO per 1 CO2 A reading of CO in the room centre should give a rise of less than 9ppm over ambient peak reading Gfaher ay UK IRL 8 4 List of spare parts Description Surround antracite Surround Stainless steel Glass Burner G20 FB Burner G20 PB Burner G20 LB Burner LPG LB Adapter Log set Spark wire Receiver Remote control Gas Control NL NG Motor remote control Pilot burner assemb NG Pilot burner assemb LPG Thermocouple Oxypilot L1200 Snoer oxypilot L1200 Spark electrode Embers spray for comb Chamber spray for frame 40 lt lt Straight Number 20847448 20847803 04510300 X 20900231 20900230 20900224 20604100 20798200 06022030 20604610 20603900 37003089 37003086 20900145 20900154 37002046 20605300 06022050 06006600 20793400 09000008 09000014 Relaxed Number 20847548 50847903 04510500 20900233 20900232 X X 20604100 20798900 06022030 20604610 20603900 37003089 37003086 X X 37002046 20605300 06022050 06006600 20793400 09000008 09000014 Gfaher User guide faber gt gt gt 41 UK IRL 42 lt lt Gfaher UK
8. of the Roundscreen table nr 5 Allowed but without flue restrictor Remove the flue restrictor Example calculation 2 fig 2a CalculatiOn horizontal extension fig 2b Flue lenght J L 0 5 0 5 1m Elbows K M 2m 2m 4 m Terminal im Total horizontal extension 6m Vertical Flue lenght H 1m When calculating on basis of the Widescreen table nr 2 Combination not allowed When calculating on basis of the MV100 table nr 3 Allowed but without flue restrictor Remove the flue restrictor When calculating on basis of the MV150 table nr 4 Combination not allowed When calculating on basis of the Roundscreen table nr 5 Combination not allowed 18 lt lt Gfaher BF110V with logburner UK IRL Note the BF110V Straight with logburner can be lead directly to the wall using a pipe bend Determine according to the table 2 the right total horizontal and vertical length When meeting an x and when the values are outside the table the combination is not allowed The 30 mm flue restrictor is normally preinstalled Tabel 2 Possible lenth and height combinations BF110V Straight BF120H Relaxed 0 1 2 3 4 5 6 0 1 2 3 4 56 0 x 0 x x x x x X X X x x x 0 5 30 X x x x x Q0 XX x x x 1 30101010 x x 0 0 0 x xx p 15 40 80 0 0 0 0 x 3030 0 0 0 xx i 2 40 30 0 0 0 0 0 3030 0 0 0 0 0 31
9. place the new ones 2x LRO3 AAA Alkaline long life 1 5 V 4 Click the battery clip into the remote control and close the cover 5 It might be possible that you have to set the transmission code after changing the batteries see 10 4 3 Note Batteries are chemical waste and should be disposed in accordance with local regulations 48 lt lt Gfaher UK IRL 11 Cleaning and service instructions Important Turn off the fire and allow it to cool down before commencing cleaning It is recommended that the fire is inspected serviced by a competent person at least once a year To maintain the finish on the trim wipe with soft damp cloth only Do not use abrasive cleaners polish or solvents as these can damage the surface finish Cleaning the glass To remove the glass to clean it follow the steps described in paragraph 4 5 To clean the glass follow the steps and suggestions described in paragrapg 8 1 1 Be sure that there are no fingerprints on the glass It is not possible to remove those prints after you burn the appliance for a while they are burnt in Gfaher gt 49 UK IRL 12 Disposal of packaging and appliance The appliance packaging is recyclable The packaging could include the following materials e Cardboard e CFC free foam soft e Wood Plastic e Paper e Batteries These materials should be disposed responsibly and in conformity with government regulations Batteries are consi
10. the safety device 46 lt lt Gfaher UK IRL Failure in the pilot flame system Contact a qualified installer when the appliance goes off regularly 10 4 Remote control version The remote control is only meant to regulate the flames from off till max It functions only when the pilot burner is ignited and knob A is in big flame position It is therefore not possible to ignite or extinguish the pilot flame with the remote control Note The radio frequency remote control is intended for fireplaces installed in a domestic setting in all EU countries except Austria Denmark Finland and Greece Features Manual control will always remain possible The remote control is a radio frequency type and had been approved internationally The remote control generates a unique safety code every time you activate the transmitter its similar to those used in a car The remote control is easy to install retrospectively 10 4 1 Using the remote control l Light the appliance as described in 10 2 2 Setthe on off switch on the receiver to on and control the flames Low flame High flame 3 Use high and low to achieve the desired heating and flame effect 4 You will hear a beep every time the receiver recognises a signal If not see 10 4 3 setting the right transmission code 5 When the fire is not be used for a prolonged period turn off the pilot see 10 4 2 If the appliance is not us
11. 40 4013010 0 010 3030 0 0 0 0 0 4 15014014013010 10 O0 40 40 30 0 0 00 u 5 150 50 40 40 30 30 0 50 50 40 301 0 010 6 50 50 50 40 40 30 0 50 50 50 30 30 0 0 i 7 60 50 50 40 40 40 x 50 50 40 30 30 0 x 8 60 60 50 50 50 x x 50 40 30 30 0 x x 9 160 60160 50 x x x 50 50 40 30 x x x 10 65 60 60 x x x x 5555 560 x x x x 11 65 65 x x x x x 5555 x x x x x 12 65 x x x x x x 55 X X X X x x The BF110V Straight with logburner can be lead directly to the wall using a bend pipe Gfaher gt gt 19 UK IRL lt lt lt 3 3 1 Terminal position Verify if the required terminal position meets the local installation regulations regarding disturbance good functioning and ventilation Also see safety requirements Note The terminal must be located so that the outlet is not obstructed If the flue terminal is located within 2 meters of a footway path or where people could come into contact with it then a suitable terminal guard must be fitted Terminals located close to shared walkways footpaths etc could be subject to legal constraints and this should be pointed out to the customer before installation If in any doubt about flue location advice should be sought from local building control or if appliance related from the manufacturer including wherever possible a dimensioned sketch Avoid locating the terminal in close proximity to plastic materials such as gutter
12. C see fig 22 some and apply the meetslang 34 lt lt Gfaher UK IRL Check if the measured pressure is the same as the prescribed pressure 4 Perform this measuring when the appliance burns on full capacity and when only the pilot ignition burns 5 When the pressure is too low check if the gas pipes are made of material wit the right diameter 6 When the pressure is too high more than 5 mBar you can t install the appliance and you should contact your gas company 7 Always check the burner pressure when the functional pressure is right You can measure the burner pressure by using sensor D The pressure should match the prescribed pressure If this is not the case then contactn the supplier Note After checking the burner pressure the Inlet pressure test point has to be shut and checked for gas tightness Gfaher UK IRL 7 Final check and handing over Instruct the customer on the full operation of the appliance Advise the customer how to clean the appliance including the glass Instruct the customer on the operation of the remote control including the replacement of batteries and how to set the right transmissions code Hand over these instructions including the user guide to the consumer Recommend that the appliance should be serviced by a competent person at least once a year 36 lt lt Gfaher UK IRL 8 Servicing To ensure safe and efficient operation of the appliance it is neces
13. Natural Fires BF110V Straight and BF120H Relaxed Installation Guide and User Manual faber UK IRL 2 lt lt lt Gfaher UK IRL Content Content t 1 Content a a SENSE DE 3 1 Introduction sa ac aima amaan emana vad 5 2 Safety instructions seeren eee 6 3 Installation requirements enn nnn n nn nn n nn 7 3 1 Builders opening and surround sss 7 3 2 Dimensions of the fire place ennen eee ee eee mmn 10 3 3 Flue requirements csse nemen nnns 17 373 15 Terminal position oio o eR SEE a ede ERN EQUES 20 3 3 2 Using an existing chimney as air inlet nennen eenen eenen 21 4 Instalation instructions nnn nn n n nnn 22 4 1 Gas connectlonz iio eor ee NRR dui ont leer 22 4 2 Preparing the appliance eneen eneen enn 22 4 3 Installing the appliance with the Faber false chimney breast 23 4 4 Installing the appliance in an existing or different false chimney breast 23 4 4 Preparing th Surround esperigi nn WR EE veen Rn ERE ERE ed dee 23 4 4 2 Installing the appliance 0 mmm 24 4 4 3 levelling and fixating the appliance eneen eenen nene naene anna 24 4 4 4 Building the false chimney breast cece cece nene nne eee teeter nen 24 4 5 Removing placing the glass nennen mee 25 4 5 1 Removing placing the glass of the BF110V Straight ne 25 4 5 2 removing placing the glass of the BF120H Relaxed eneen 26 4 6 placing and
14. ance Bu Um Make sure you place the pipes in the right direction the narrow end towards the appliance 5 Make sure the pipes are fixed sufficiently a wall clamp every 2 m This way the weight of the pipes is not resting onto the appliance 6 The outside of the pipe can be hot 140 degrees Stay at least 50 mm away from wall surface or ceiling Make sure to provide sufficient heat resistant isolation when going through the wall or roof 7 The concentric pipes can turn loose due to expansion or cooling down It is recommended to fix the spring clip with a self tapping screw at inaccessible places 8 To get the exact measure flue length you can use cut down concentric pipe wall mounted terminal or roof mounted terminal To obtain a smoke sealed connection the inner pipe must be 20 mm longer then the outside pipe 5 2 Connection onto an existing chimney You can connect the appliance onto an existing chimney The existing chimney then functions as an air supply channel where a flexible stainless steel liner to BS715 of 100 mm performs the flue function Any existing chimney used as an air supply channel must only service this appliance Requirements 300 mm of free space above the appliance The chimney only supply s air to this appliance The existing chimney needs to be clean and very well swept The existing chimney needs to be airtight The existing chimney needs to have an opening of min 150 x 150 mm Gfah
15. ble Fireguard conforming to BS6539 and BS6778 should be used with this appliance to protect children the elderly or infirm Care should also be taken with pets In your own interest and that of safety all gas appliances must be installed by competent persons Installation must be in accordance with National Regulations CORGI registered Gfaher ssa UK IRL installers are required to work to recognised standards Note Since the appliance is a source of heat circulation of air occurs Therefore it is of importance that you do not use the appliance shortly after a renovation of the home Because of the natural circulation of air moist and volatile components from paint building materials carpet etc will be attracted These components can settle themselves down onto cold surfaces in the form of soot As on all heat producing appliances soft furnishings such as blown vinyl wallpaper placed too near to the appliance may become scorched or discoloured This should be born in mind when installing the appliance 44 lt lt Gfaher UK IRL 10 Controlling the appliance 10 1 General If the main burner or pilot light is extinguished for any reason don t try to relight the pilot within 5 minutes Contact a qualified installer when the appliance goes off regularly Depending on the model the gas control block is positioned e BF110V Straight Frameless behind a stainless steel door at the underside of the appliance mounted in the mi
16. bustion chamber and burner 1 Carefully remove the logs 2 You can clean the combustion chamber with a vacuum cleaner 3 Place back the logs as described in paragraph 4 6 If the burner is visibly damaged this can affect the distribution of the flame If so then replace the burner Logburner Met opma Aangepaste RGB 41 37 fig 23 A Pilot assembly B Burner Flat fibre burner C Fixation plate Met opma D Injector Tekstkleur E Gas control RGB 41 37 F Receiver Pebble burner Met opma Tekstkleur RGB 41 37 ID C 38 lt lt lt faber UK IRL 8 1 3 Burner tray dis assembly 1 Break the gas supply at the control valve 2 Remove the glass the log set grid and burner tray cover 3 Detach the gas connection at the 8 mm nut and olive 4 Unscrew the burner assembly and take them out of the combustion chamber 8 1 4 Gas control block Unscrew and remove the pilot system from its support and the burner plate Disconnect the ignition spark cabel Disconnect the thermocouple from the pilot system 1 2 3 4 Disconnect the gas connection from the pilot system Mind the injector it s unattached 5 The pilot system can now be removed 6 To assemble the pilot system again follow the steps above in reversed order gie Governor Adjusting screw pilot flame Inlet pressure test point Burner pressure test point 8 2 Propane conversion For conversion from propane to natural
17. ddle of the floorplate of the appliance e BF110V Straight with frame Within the false chimney breast or surround at either the left or right side of the appliance mounted on the floor plate of the appliance An optional hatch can be purchased with this model for easy access to the gas block With control button A you can light the pilot With the control button B you can adjust the height of the flames see figure All Natural Fire models feature a remote control which controls the height of the flames fig 25 Gas control box Knob A The 6 isthe OFF position preventing any gas from passing through the control valve to either the pilot burner or to the main burner By pressing the knob in it is possible to turn it anticlockwise The first function is to turn on the gas to the pilot this occurs just before reaching the position if the fire has not been lit for some time it may be necessary to hold the knob in this position for some seconds to clear the air from the pipe and allow gas to reach the pilot burner Once gas is available at the pilot continued rotation anti clockwise will cause the piezo igniter to spark This is accompanied by a click at the valve and should result in the pilot burner igniting Once the pilot is lit the control knob should be held pressed in for 10 seconds In this time the pilot flame will have heated the flame Gfaher gt gt 45 UK IRL supervision thermocouple sufficiently to operate a hold on mag
18. dered chemical waste The batteries should be disposed of responsibly and in conformity with government regulations Remove the batteries before disposing of the remote control Information on how to responsibly dispose of discarded appliances can be obtained from the local authorities 50 lt lt Gfaher UK IRL Appendix technical data BF110V Straight BF120H Relaxed Type of burner log burner Pebble burner flatfiber log Pebble burner UK IRL UK IRL UK IRL UK IRL 12H 12H 12H 12H C11 of C31 C11 of C31 C11 of C31 C11 of C31 Gas casis Type of gas Heat input Hi net kW Er 2m FS Efficiency class 2 2 2 2 NOX class 4 4 4 4 Working pressure mbar 20 20 20 20 gas rate 15 C en 1013 mbar l h 761 780 870 870 Setting pressure mbar 9 5 10 13 13 Injector size mm 2x 1 60 1 50 2 55 2 55 2 55 Reduced input restrictor mm 1 8 1 8 1 8 1 8 Type SIT 160 SIT 160 SIT 160 OP9709 code injector Nr 51 Nr 51 MV size mm 100 150 100 150 100 150 100 150 Preinstalled flue restrictor mm 30 30 30 30 Gas control GV36 GV36 GV36 GV36 C5AOEHC68M C5AOEHC68M C5AOEHC68M C5AOEHC68M aiiis s Voltage adaptor 3 2x LR03 1 5V 2x LR03 1 5V 2x LR03 1 5V X 2xLROS 1 5V Batteries V Alkaline Alkaline Alkaline Alkaline Gas connection 8 mm nut amp 8 mm nut amp 8 mm nut amp 8 mm nut amp Gfaher gt gt 51 UK IRL faber Saturnus 8 NL 8448 CC Heerenveen Postbus 219 NL 8440 AE Heerenveen T 431 0 513 656500
19. e paragraph 3 2 and is secured by the floor plate e Minimum distance from the back of the appliance to the wall has to be 10mm e Always install the fire place first before building up the false chimney breast e Always ventilate the space above the appliance using vents to assure a good air circulation e Ifthe appliance is to be fitted against a wall with combustible cladding the cladding must be removed from the area covered by the surround e The plaster of the outside has to be resistant to a high temperature Therefore use the Gfaher gt gt 7 UK IRL plaster materials especially made for this to prevent discoloring min 100 C temperature resistant Make sure the plaster dries well before using the appliance Let the thickness in mm be the number of days the plaster has to dry e g 3 mm plaster has to dry for 3 days Although the appliance is tested for installation without a hearth the appliance must not stand on combustible materials or carpets If the appliance is placed ona combustible floor first place a fibrelux or similar heatproof board of 12 mm thickness Any under floor vents or openings within the builders opening should be sealed off If the floor will be adjusted e g by applying carpet or parquet the floor under the false chimney breast has to be adjusted to match the future floor height Do not place any material directly onto the appliance If possible apply a lintel made of cement or something similar
20. eceiver should now go out Again push a button on the remote control The lamp starts flashing and will switch off eventually The receiver now recognizes the remote control The remote control now functions Check if you can hear a sound and the motor runs when you push a button on the remote control 32 lt lt Gfaher UK IRL 6 Commisioning functional checks 6 1 Check pilot ignition 1 Push in and turn the control knob A from 9 anticlockwise to the 4 small flame setting You will hear a tick meaning there is ignition Hold the knob in and wait for a few seconds while the air is purged Bring the knob back in the start position and turn the knob several times to the large flame position Check that the pilot has lit Continue to hold in the control knob for a further ten seconds to ensure that the pilot flame is stable Release the knob The pilot should remain alight A B 6 2 Functional burner check 1 2 Turn knob B to max clockwise Turn the knob A more anticlockwise to the position large flame Now it is possible to light the main burner Turn knob B anticlockwise to max The main burner should light Check for gas soundness at all joints with leak detection fluid Check the ignition of the main burner on low and high setting 5 Turn knob B clockwise till The main burner is off 6 Turn the knob A to 9 The pilot should go out Gfaher gt gt 33 UK IRL 6 3 Functio
21. ed for an extensive period of time it can be necessary to set the right transmission code again Gfaher 247 UK IRL 10 4 2 Setting the right transmission code The receiver has to learn the code from the transmitter This is already done at the factory However the code disappears if the receiver is disconnected from the mains too long 1 Set the on off switch on the receiver to on fig 27 Rear of remote control Push the mod button on the receiver and hold it for 3 seconds The green control lamp will light up and stay on Repeat this step if it doesn t 4 Pusha button on the remote control The control lamp on the receiver should now go out 5 Again push a button on the remote control The lamp starts flashing and will switch off eventually 6 Thereceiver now recognizes the remote control The remote control now functions 7 Check if you can hear a sound and the motor runs when you push a button on the remote control 10 4 3 Changing the batteries The batteries in the remote control should have a life span of about one year depending on the frequency of use There is no risk of electric shock as the low voltage supply is similar to that used in torches Always turn off the appliance before changing batteries Remote control 1 Remove the cover on the back of the remote control 2 Carefully remove the battery clip along the side Pay attention not to pull the wires 3 If necessary remove the old batteries and
22. er 2229 Fire place side 5 UK IRL Chimney side 1 Place the aluminium closure plate A onto the chimney Permanently attach and make airtight 2 Pull the liner C through the chimney 3 Connect the liner onto the roof terminal and fix it with the clamp provided with the chimney connection set 4 Place the roof terminal onto the closure plate Fixing the chimney sealing plate D and place the 150 mm grommet into the hole of the sealing plate Fixing the chimney sealing plate D and place the 150 mm grommet into the hole of the sealing plate 6 if necessary install an MV pipe on the fire place in such a way that the chimney connection and the MV system is 500 mm 7 Fixthe sealing plate air tight into the builders opening use the isolation rope from the chimney connection set to make the plate air tight 8 Slide the pipe E 150 mm length 500mm into the sealing plate Slide this pipe so far that you will have a space of 200 mm later on for assembling the liner 9 Install the appliance 10 Connect the flexible stainless steel liner onto a pipe using the 200 mm long 100 mm pipe F as adapter 11 Slide the outside pipe onto the appliance or concentric extension so that you have a air tight connection 5 3 Remote control The remote control is only meant to regulate the flames it functions only when the pilot burner is ignited It is therefore not possible to ignited the appliance with the remote con
23. he desired situation is possible To establish this you will need to calculate The effective height this is the real difference in height between the upper side of the appliance and the terminal The total horizontal extension This is the total horizontal flue length where o Each elbow which is in the horizontal area counts for 2 meters o Each 45 degree bend which is in the horizontal area counts for 1 meter o Elbows and bends at the transition of horizontal to vertically are not to be counted o The wall mounted terminal counts for 1 meter Flue restrictor If applicable in the table is also stated the size of a flue restrictor This restrictor needs to be fitted in the combustion chamber when placing the appliance see chapter 4 2 Normally the smallest flue restrictor is fitted Gfaher gt gt 17 UK IRL Example calculation 1 Calculating horizontal extension fig 2a Flue lengh C E2 1m 1m 2m Elbows D 2m 2m Total horizontal extension 4m Measure or calculate effective height Hvert Flue lenght A 1m Roof mounted terinal 1m Total effective height 2m When calculating on basis of the Widescreen table nr 2 It is allowed Remove the flue restrictor When calculating on basis of the MV100 table nr 3 Allowed but without flue restrictor Remove the flue restrictor When calculating on basis of theMV150 table nr 4 Allowed but without flue restrictor Remove the flue restrictor When calculating on basis
24. himney breast is completed Make sure that the foil is removed when the appliance is used 4 5 2 removing placing the glass of the BF120H Relaxed 1 Take away the frame of the BF120H Relaxed see 4 6 2 slide the strips on either side of the appliance to the outside 3 unscrew the screw mounted on the right side of the appliance which secures a handle see fig 3 and 4 4 Move the handle towards you The glass is now unsecured gently grab the glass on either side Tilt the glass a little bit backwards If this not possible move the handle more downwards 6 lift the glass with its top in th false chimney breast 7 Take the glass out of the false chimney breast 8 To place the glass back on the appliance follow these steps in reverse order Note when placing the glass make sure that the handle is moved backwards sufficiently If this is not the case securing the glass will not be possible The glass is protected with a foil which should be removed only after the whole installation and finishing of the appliance and false chimney breast is completed Make sure that the foil is removed when the appliance is used 26 lt lt lt 4 6 placing and adjusting the frame 1 After the appliance is properly installed the frame has to be placed for this purpose a movable lip is mounted on top of the appliance 2 This lip can be secured by fastening two bolts on either side of the appliance 3 Adjust the positi
25. imney breast Building up the false chimney breast with e g Ytong blocks is not possible e The gas block is normally mounted on the right side of the appliance but can be place elsewhere thanks to a 1 2 m flexible gas line e Make sure the that the top ridge of the wall opening is left out see drawings in 3 2 This is necessary to be able to remove the glass and assure a good air circulation Gfaher see UK IRL 3 2 Dimensions of the fire place Model dimensions BF110V BF110V BF120H BF120H Straight Straight frameless with frame frameless with frame Frames Max height outer frame Height opening inner frame a Distance bottom appliance bottom frame Installation Dimensions Height wall opening height dag 1100 1100 425 636 270 Bottom applicance bottom wall opening ma 74 159 43 ma ma Max height applicance 1181 1181 688 68 12 Flue Dimensions Distance wall DC connection frame thickness with 3mm play distance higher than the floor plate Width floor plate with DC box Depth builders opening including distance to the glass On the next few pages the dimensions of the BF110V Straight and BF120H Relaxed are visualised in drawings 10 lt lt lt Gfaher UK IRL BF110V Straight Frameless 12 mm Promatec Top view false chimney breast muur wall Top view of the appliance
26. nal balanced flue check 1 Set the appliance on max input 2 Verify the flame picture this means no flames against the window the flame have to come besides the logs if not check the log layout 3 Check if the flames are yellow after 10 minutes of operation If you still have a blue flame or the appliance goes out check If the flue pipes are fitted correctly no leakage If the wall mounted terminal is placed with the correct side up If the maximum allowable length of the flue pipe was exeeded Ifthe appliance has the right set up Check the x If the correct flue restrictor is installed EE oe Governor Adjusting screw pilot flame Inlet pressure test point Burner pressure test point 6 4 Check reference pressure and burner pressure The appliance is preset to give the correct heat input No further adjustment is necessary Fit a pressure gauge at the burner pressure test point D to check the burner pressure The pressure should be checked with the appliance alight and at max input The setting pressure should be as shown at the technical data After checking the pressure turn off the appliance Remove the pressure gauge and close the sealing screw Re light the appliance Turn to max input and test around the test point D for gas soundness using a suitable leak detection fluid Measuring the pressure voordruk 1 Turn off the gas valve on the appliance 2 Turn the Inlet pressure test point
27. net within the valve Now turn the control knob A to the amp position This allows gas to enter control knob B Knob B The is the OFF position preventing gas entering the main burner if the pilot is lit The knob should be turned slowly anticlockwise This allows gas to enter the burner and be ignited by the pilot flame Once ignition has taken place the fire may be set to any level between min and max by adjusting the control knob B 10 2 To light 1 Push in and turn the control knob A from anticlockwise to the setting small flame You will hear a ignition click Check that the pilot is lit if not repeat 2 Continue to hold in the control knob for a further ten seconds to ensure that the pilot flame is stable 3 Release the knob The pilot should remain alight Turn the control knob A to the amp position Turn knob B slowly anticlockwise the fire should then ignite ne Adjust flames to the required level 10 3 To extinguish 1 For the main burner turn the control knob B clockwise to position 2 To disable knob B turn knob A to the position 3 To extinguish the pilot turn control knob A to position although it is in order lo leave the pilot permanently lit 10 3 1 When the pilot extinguishes Warning When the pilot extinguishes for whatever reason you should wait at least 5 minutes before trying to turn it on again Possible causes of pilot extinguish are Operating error Interference of
28. nted window construction A specially designed Faber prefab false chimney breast is optional only for the frameless versions of the Natural Fires Realistic flame and glow effect because of the Log burner technology Room sealed appliance inlet and outlet are led to the outside using a natural draught concentric pipe system 100 mm 150 mm No additional ventilation required Air supply and flue gases go to outside atmosphere through wall or roof A maximum horizontal extension of 6 meters is possible Remote Control option on all appliances Meets the essential requirements of the European Gas Appliance Directive GAD and carries the CE mark according the NEN 613 standard Gfaher oie UK IRL 2 Safety instructions Before installation ensure that the local distribution conditions identification of the type of gas and pressure and the adjustment of the appliance are compatible This information can be found on the data plate This gas appliance is factory set and shall not be adjusted This appliance does not contain any component manufactured from asbestos or any asbestos related products The pilot and flame sensing device fitted to this fire is also a safety device If for any reason any part of the pilot assembly is to be replaced the entire assembly including the pilot burner thermocouple electrode and injector must be exchanged complete for a pilot assembly from the original manufacturer only Do not put extra glo
29. on of the lip so that its top edge is positioned about 3mm from the wall including finishing 4 Place the frame over the lip Make sure it is positioned in the middle faber gt gt gt 27 UK IRL 4 7 Placing the log set with the log burner To guarantee good combustion the log set may only be installed in the way specified on the picture below Never place extra elements of any kind into the combustion chamber This could affect the combustion in a negative way Any other arrangement can lead to soot on logs or window Do not use the fire with broken or missing logs When preferred ember immitation ash kan be spread around the logs Attention Beware that there are no embers on the air inlet at the back BF110V Straight log burner F BF120H Relaxed flat fibre burner BF110V Straight pebble burner BF120H Relaxed Pebble burner 4 8 Placing the pebbles with pebble burner Spread the pebbles over the bottom plate To ensure a good combustion spread the pebbles equally Make sure that the pilot burner stays free from the pilot The pebbles do not need further servicing See pictures above for more details 28 lt lt lt Gfaher UK IRL 5 Installation of the flue 5 1 Connections with use of concentric duct material 1 Drill a hole of 153 mm for the wall or roof mounted terminal Horizontal parts of the pipe have to be installed with an angle of at least 3 degrees Build up the system from the appli
30. pipes should be in accordance with BS 6891 Pipe work from the meter to the appliance must be of adequate size The complete installation including the meter must be tested for soundness and purged as described in the above code A means of isolation must be provide in the supply to facilitate servicing The connection should be made in 8 mm copper or similar semi flexible tube max 1 meter Ensure that the gas pipe does not interfere with the removal or replacement of the burner tray of the controls The gas connection is nut and olive suitable for 8 mm pipe Make sure there is a gas connection with a diameter of 8 mm goes directly from the gas meter to the appliance with a CE approved sealing valve G 1 2 This valve has to be accessable at all times Check the connection for gas leaks The gas connection is positioned on the right of the appliance You can choose to place the sealing valve on the in or outside the false chimney breast When mounted inside a small hatch has to be installed can be ordered separately If the gas connection comes out of the floor in the false chimney breast a hole of sufficient size has to be drilled Mount the supplied nut and olive of 8 mm directly on the gas unit Then you can go on installing a fixed or flexible connection This has to be CE certified When installed as described above the burner can always be disassembled for servicing 4 2 Preparing the appliance 1 Remove the
31. s or other combustibles If this is unavoidable then a suitable deflector should be made Some important requirements for a good functioning are The wall mounted terminal has to be at a distance of at least 0 5 meters off o Corners of the building o Below eaves o Balcony s etc unless the duct is dragged to the front side of the overhanging part The roof mounted terminal has to be at a distance of at least 0 5 meters of the sides of the roof excluded the ridge 20 lt lt Gfaher UK IRL Site in accordance with BS 5440 1 2000 and the document J boundary 3 3 2 Using an existing chimney as air inlet The appliance can be connected onto an existing chimney The existing chimney then functions as air supply where a flexible stainless steel liner to BS715 of 100 mm performs the flue function Requirements Any existing chimney used as an air supply must only service this appliance Achimney that has previously been used for solid fuel must be swept before use The existing chimney needs to be airtight The existing chimney needs to have an opening of min 150 x 150 mm The chimney needs to be intact and well looked after Use the adjustable roof mounted terminal especially made for this and the chimney connection set The minimum distance between two terminals should be at least 450 mm faber nn V UK IRL A Instalation instructions 4 1 Gas connection Installation
32. sary to carry out routine servicing at regular intervals It is recommended that the fire is inspected serviced by a competent person at least once a year Important turn off the gas supply before commencing any servicing Always test for gas soundness after refitting the appliance The appliance and flue connection have to be checked for gas and smoke soundness after installation 8 1 Routine servicing l Clean if necessary the pilot system the burner the combustion chamber the glass 2 Check the log lay and replace the embers if applicable 3 Do the functional test as described at page 34 4 Check the flue system and terminal on damage and soundness visual inspection 8 1 1 Cleaning the glass Depending on the intensity of use you can get a deposit on the glass Normally this can be removed with an ordinary dry towel If necessary special ceramic glass cleaner ceramic cook top cleaner can be used To clean the glass 1 Remove the glass as described in paragraph 4 5 2 Clean the glass Handle the glass with clean hands wear gloves if possible 3 To fit the glass proceed in reverse order Make sure that 1 the log set has been installed correctly before fixing the glass 2 the glass sealing rope is in good condition and makes an effective seal 3 Important be sure that there are no fingerprints on the glass They are burned in the glass when not removed Gfaher UK IRL 8 1 2 Cleaning the com
33. screws from the front legs see figure 2 You can now remove the appliance from the floor plate 22 lt lt Gfaher UK IRL 4 3 Installing the appliance with the Faber false chimney breast When the appliance is purchased with a Faber false chimney breast then first follow the instructions delivered with the package of the false chimney breast 4 4 Installing the appliance in an existing or different false chimney breast Read the requirements described in paragraph 3 1 before continuing with the installation 4 4 1 Preparing the surround 1 Check if the floor and wall are sufficiently level If necessary improve it 2 If the floor will be raised higher e g by installing carpet or parquet the floor underneath the fire place has to be equally raised Insulate the back wall with promatec of comparable inflammable material 4 Drill holes for the flue routing Minimum height with flue routing through the back wall is the height of the appliance plus the pipe bend When going through the roof a hole with a diameter 200mm has to be drilled in the ceiling at a distance of 170 mm from the wall to the heart of the hole This hole indicates the centre of the false chimney breast Moving it afterwards is not possible 5 Adjust the floor plate if necessary e Drill a hole on the floor plate where the gas connection will come out of the floor e Cut off the knockouts A en B see figure which are meant for the Faber fal
34. se chimney breast 6 Position the floor plate and mount it to the floor 7 Prepare the gas connection see paragraph 4 1 Gfaher 2 223 UK IRL 4 4 2 Installing the appliance 1 Turn the 4 legs until they are extended 20 mm 2 Install the appliance with the two front legs positioned between the supports on the floor plate 3 Lift the appliance gently over the supports then put um it down 4 Make sure that the gas connection isn t stuck between the receiver holder and the floor plate 4 4 3 levelling and fixating the appliance l Level the appliance in all directions by adjusting the legs underneath the appliance 2 Secure the legs Secure the appliance to the wall 4 Install the flue routing as describes in chapter 5 4 4 4 Building the false chimney breast You are now ready to build a false chimney breast construction If you purchased the BF110V Straight Frameless you can use the distance holders on top of the appliance to fixate the construction and keep the builders opening at a minimum width of 460 mm Keep in mind that this is measured with the finishing e g plaster Note The width of 460 mm of the builders opening is very critical since this is the minimum width with which the glass can be taken out If the opening is made much wider the construction of the appliance can become visible Frequently check the distance from the front of the glass to any of the construction par
35. trol or to shut off the pilotflame The radio frequency remote control is intended for 30 lt lt Gfaher UK IRL fireplaces installed in a domestic setting in all EU countries except Austria Denmark Finland and Greece Features Manual control will always remain possible The remote control is a radio frequency type and has been approved internationally The remote control generates a unique safety code every time you activate the transmitter its similar to those used in a car The remote control is easy to install retrospectively ul 3 1 Installation remote control Connect the mains adapter to the receiver box The adapter is set to the correct 52 voltage in the factory 4 5 V Slide the receiver box into the holder Connect the wires to the gas valve see fig 22 Check that there are batteries in the transmitter See Replacing batteries see chapter 10 4 4 Qu a vp eU US Set the on off switch on the receiver to on Gfaher UK IRL Setting the right transmission code The receiver has to learn the code from the transmitter which is already done at the factory However the code disappears if the receiver is disconnected from the mains for a longer period 1 2 3 Push the mod button on the receiver and hold it for 3 seconds The green control lamp will light up and stay on Repeat this step if it doesn t Push a button on the remote control The control lamp on the r
36. ts of the false chimney breast is at least 12 mm for the 24 lt lt lt Grana BF110V Straight Frameless Again this is to be able to take out the glass 4 5 Removing placing the glass the BF110V Straight as well as the BF120V Relaxed use the same kind of securing system for the glass The only difference is in the place where the glass is secured This has an effect on how the glass has to be removed sideways for the BF110V Straight and up for the BF120H Relaxed on the following two pages removing the glass handle will be explained using pictures 4 5 1 Removing placing the glass of the BF110V Straight l Take away the frame or the stainless steel door 2 Unscrew the two screws underneath on either side of the glass a few centimeters 3 Move both handles as far towards you as possible The glass is now unsecured 4 Grab the glass both under above Move the left side of the glass towards you then move it to the left and down as far as possible 5 Bring the right side of the glas towards you out of the false chimney breast 6 To place the glass back on the Gfaher UK IRL appliance follow these steps in reverse order Note make sure that both handles are moved as far towards you as possible otherwise securing the glass won t be possible The glass is protected with a foil which should be removed only after the whole installation and finishing of the appliance and false c
37. use the appliance shortly after a renovation of the home Because of the natural circulation of air moist and volatile components from paint building materials carpet etc will be attracted These components can settle themselves down onto cold surfaces in the form of soot As on all heat producing appliances soft furnishings such as blown vinyl wallpaper placed too near to the appliance may become scorched or discoloured This should be born in mind when installing the appliance 3 1 Builders opening and surround Both the BF110V Straight frameless and the BF110V Straight frameless can be build in an optional Faber prefab false chimney breast made of promatec This false chimney breast is specially designed to accommodate this type NOT for the models with frame and is applicable for ceiling heights up to 2 9m It consists of a base part and either a top part made of promatec or an ornamental flue pipe made of stainless steel The fire place can also be build in a non combustible fire place or builders opening This could be either an existing builders opening or a new made prefab builders opening For the measurements see paragraph 3 2 When you apply your own false chimney breast design to all models of the BF110V Straight or BF120H Relaxed you have to meet these general requirements e The false chimney breast has to be made of inflamable material e The minimum inner width of the false chimney breast has to be at least 976mm se
38. w elements in the combustion chamber This could affect the burning process in a negative way This appliance is room sealed and doesn t require purpose provided ventilation It is the law in the UK that all gas appliances are installed and checked by a competent person in accordance with the Gas Safety Installation and Use Regulations as amended the relevant British Standards for Installation work Building Regulations Codes of Practice and the manufacturer s instructions The installation should also be carried out in accordance with the following where relevant e British Standards BS5871 Part1 BS5440 Parts 1 amp 2 and BS1251 e Building Regulations Document J as applicable e Building Regulations and Standards issued as relevant by the Department of the Environment or the Scottish Development Department In the Republic of Ireland installation should be carried out in accordance with 15813 ICP3 15327 Building Regulations Codes of Practice the manufacturer s instructions and any other rules in force Failure to comply with the above could leave the installer liable to prosecution and invalidate the appliance warranty The construction of the fire place is not to be altered Safety instructions for the user can be found in chapter 9 6 lt lt Gfaher UK IRL 3 Installation requirements Note Since the appliance is a source of heat circulation of air occurs Therefore it is of importance that you do not
Download Pdf Manuals
Related Search