Home

LCD Entertainment System

1. L Feed the REMOTE CONTROL CABLE through the LEFT INNER HANDLEBAR COVER as shown Replace the LEFT INNER HANDLEBAR COVER onto the ERGO CROSSBAR NOTE Be careful not to pinch the LIFEPULSE CABLE when replacing the LEFT INNER HANDLEBAR COVER Position the ERGO CROSSBAR between the HANDLEBARS Connect the 2 PIN LIFEPULSE CONNECTORS Secure the ERGO CROSSBAR in place using the four previously removed SCREWS Tighten the SCREWS securely NOTE Be careful not to pinch the LIFEPULSE CABLE when replacing the ERGO CROSSBAR Position the RIGHT OUTER HANDLEBAR COVER near the right end of the ERGO CROSSBAR Secure it to the RIGHT INNER HANDLEBAR cover using two previously removed SCREWS Tighten the SCREWS securely First routing the REMOTE CONTROL CABLE forward along the HANDLEBAR as shown position and secure the LEFT INNER and OUTER HANDLEBAR COVERS Tighten the SCREWS securely Secure the REMOTE CONTROL to the left end of the ERGO CROSSBAR as shown Be sure the CABLE TIES are pulled tight and trim the excess CABLE TIES Route the remaining REMOTE CONTROL CABLE along the edge of the LEFT UPRIGHT up through the cable guide and through to the top of the DISPLAY CONSOLE Locate the COAXIAL CABLE and FEMALE FEMALE COUPLER Attach the FEMALE FEMALE COUPLER to one end of the COAXIAL CABLE Locate the POWER SUPPLY and POWER CORD EXTENSION CABLE KIT Attach the POWER CORD EXTEN SION as instructed in the kit Using a Flexib
2. 10 11 12 13 14 15 16 17 18 19 Position the MONOCOLUMN COUPLER near the bottom of the UPPER MONOCOLUMN ASSEMBLY Position the MAIN WIRE HARNESS POWER SUPPLY CORD and COAXIAL CABLE alongside the MONOCOLUMN COUPLER Position the previously removed MONOCOLUMN COUPLER SHROUD over all cables and secure the SHROUD in place using the two previously removed SCREWS Be careful not to pinch any of the cables when re installing the MONOCOLUMN COUPLER SHROUD Place THE MONOCOLUMN COUPLER back into position on the UPPER MONOCOLUMN ASSEMBLY and secure it using the four removed SCREWS Tighten the SCREWS to 28 32 ft lbs Lift the UPPER MONOCOLUMN ASSEMBLY into its upright position near the top of the LOWER MONO COLUMN Feed any excess cables into the LOWER MONOCOLUMN and insert the UPPER MONOCOL UMN ASSEMBLY into the LOWER MONOCOLUMN Secure the UPPER MONOCOLUMN ASSEMBLY using the four removed SCREWS Tighten the SCREWS to 15 20 ft lbs Be careful not to pinch any of the cables when re installing the UPPER MONOCOLUMN ASSEMBLY Locate the SPACER With the SPACER oriented as shown feed all the previously removed CONNEC TORS power supply cord and coaxial cable through the large center hole in the SPACER Slide the SPAC ER onto the DISPLAY CONSOLE MOUNTING PLATE making sure the top of the SPACER hooks over the top of the DISPLAY CONSOLE MOUNTING PLATE Align the mounting holes of the SPACER and DISPLAY CONSOLE MOUNTING
3. 26 Reverse STEPS 1 and 2 to return the SEAT POST SHROUDS and RIGHT CRANK ARM to their proper posi tions Tighten the CRANK ARM SCREWS to 15 20 ft lbs INSTALLATION MODELS 9500HR 9100 8500 95R1 93R 90R RECUMBENT EXERCISE BIKES Toots REQUIRED Phillips Screwdriver Side Cutters 1 8 Allen Wrench T 20 Torx Driver T 30 Torx Driver Flexible Fish Tape 1 Remove the three SCREWS securing the user RIGHT CRANK ARM Set the SCREWS and CRANK ARM aside 2 Remove the two SCREWS securing the REAR CAP to the SEAT EXTRUSION Remove the REAR CAP and set it and the SCREWS aside 3 Remove the seven SCREWS securing the RIGHT SHROUD to the LEFT SHROUD Set the SCREWS and SHROUD aside 4 Remove the four SCREWS securing the DISPLAY CONSOLE to the CONSOLE MOUNTING PLATE Carefully raise the DISPLAY CONSOLE from the MOUNTING PLATE and disconnect all CONNECTORS Note the locations of all CONNECTORS Set the DISPLAY CONSOLE and SCREWS aside 5 Locate the COAXIAL CABLE and FEMALE FEMALE COUPLER Attach the FEMALE FEMALE COUPLER to one end of the COAXIAL CABLE 6 With the POWER SUPPLY and the female connector end of the COAXIAL CABLE located near the FRONT STABILIZER route the cables together along the FRAME as shown using CABLE TIES at the locations indi cated The cables should be taught secure and free of the alternator and any moving parts Secure the POWER SUPPLY to the FRONT STABILIZER using two CABLE TIES as shown Be s
4. Do not pinch any wires when assembling the DISPLAY CONSOLE to the MOUNTING BRACKET Attach the ENTERTAINMENT CONSOLE to the UPPER MOUNTING PLATE using four SCREWS Tighten the SCREWS to 6 8 in lbs Do not overtighten the SCREWS Connect the COAXIAL CABLE POWER CABLE and REMOTE CABLE to the rear of the ENTERTAINMENT CONSOLE as shown under Console Cable Connections at the end of this section CABLE TIE any excess cable together behind the ENTERTAINMENT CONSOLE and position the cables between the ENTERTAINMENT CONSOLE BRACKET and the DISPLAY CONSOLE 15 INSTALLATION MopeLs 97X1 95X1 93X 90X CROSS TRAINERS TooLs REQUIRED Phillips Screwdriver Side Cutters T 45 Torx Wrench Flexible Fish Tape 1 10 11 12 16 Locate the COAXIAL CABLE and FEMALE FEMALE COUPLER Attach the FEMALE FEMALE COUPLER to one end of the COAXIAL CABLE Remove the two SCREWS securing the ACCESSORY TRAY to the CONSOLE MOUNTING PLATE Carefully raise theACCESSORY TRAY from the MONOCOLUMN and set it and the SCREWS aside Carefully remove the TOP CAP by squeezing inward on the sides and lifting upward Discard the TOP CAP Remove the two SCREWS securing the DISPLAY COSOLE SUPPORT COVER to the DISPLAY COSOLE SUPPORT Set the DISPLAY COSOLE SUPPORT COVER and SCREWS aside Remove the four SCREWS securing the DISPLAY CONSOLE to the DISPLAY CONSOLE SUPPORT Carefully raise the DISPLAY CONSOLE from the MOUNTING PLATE and discon
5. FEMALE FEMALE COUPLER to one end of the COAXIAL CABLE Locate the POWER SUPPLY and POWER CORD EXTENSION CABLE KIT Attach the POWER CORD EXTEN SION as instructed in the kit Using a Flexible Fish Tape feed the POWER CORD and COAXIAL CABLE male connector end up through the MOTOR PAN HOLE LEFT UPRIGHT and out the LEFT HANDLEBAR Using the Flexible Fish Tape feed the POWER SUPPLY CORD and COAXIAL CABLE male connector end up through the LEFT HANDLEBAR and out the LEFT ACCESS HOLE located at the top of the LEFT HANDLEBAR near the console edge along side the MAIN WIRE HARNESS Secure the POWER CORD and COAXIAL CABLE in the MOTOR COMPARTMENT using two CABLE TIES at the locations shown 13 14 15 16 17 18 20 Starting approximately 1 2 from the top center of the REAR CONSOLE Create a 1 2 wide by 3 8 deep notch in the REAR CONSOLE top Locate the REMOTE CONTROL Remove the two HORIZONTAL CABLE TIES H for a VERTICAL V installation Secure the REMOTE CON TROL to the left end of the ERGO CROSSBAR as shown Be sure the CABLE TIES are pulled tight and trim the excess CABLE TIES Route the REMOTE CONTROL CABLE along the LEFT HANDLEBAR Secure the REMOTE CONTROL CABLE using two CABLE TIES in the locations shown Be sure the CABLE TIES are pulled tight and trim the excess CABLE TIES Route the remaining REMOTE CONTROL CABLE along the handlebar and up through the DISPLAY CONSOLE ACCESS PANEL With th
6. amp C and re install the previously removed eight SCREWS A Tighten the SCREWS securely Do not over tighten the SCREWS Attach the ENTERTAINMENT CONSOLE J to the UPPER MOUNTING PLATE K using four SCREWS L Tighten the SCREWS to 6 8 in lbs Do not overtighten the SCREWS Connect the COAXIAL CABLE and POWER CABLE to the rear of the ENTERTAINMENT CONSOLE E as shown under Console Cable Connections at the end of this section CONSOLE CABLE CONNECTIONS A j 1 Coaxial Cable Input from cable antenna 2 Power Adapter Input 3 Remote Control Cable Input SYSTEM SETUP Turn the power on by pressing the ON OFF button 1 on the remote pe control The volume can be increased or decreased by pressing the up or OM down VOLUME ARROW KEYS 2 A volume indicator will appear on the console while the volume is being adjusted The volume indicator will disappear after five seconds of inactivity Headphones are neces O sary to hear any volume adjustments Plug headphones into the HEADPHONE JACK 3 located on the remote control j Channels can be selected by scrolling up or down through available channels by pressing the up or down CHANNEL ARROW KEYS 4 A channel indicator will appear on the console while the channel is being selected The channel indicator will disappear after five seconds of inactivity 25 SYSTEM SETUP How To ACCESS MENUS Turn the power on by pressing the ON OF
7. menus Selecting the wrong input will result in a distorted broadcast picture The program display is not affect ed by the input selection RESET Selecting RESET will reset all PICTURE options except input to the factory default settings 33 SYSTEM SETUP CAPTION TEXT MENU Selecting CAPTION TEXT will display a menu listing ofpossible closed caption ot text channels RESET ALL Information co TU Install Lansuase OSD Control Picture Selecting RESET ALL will return all settings to the original factory defaults 34 OTHER INFORMATION TROUBLESHOOTING If you are having a problem with your TV try the suggestions below If the problem persists contact Life Fitness Customer Support Services as outlined in Service Contacts at the end of this manual Problem Reset the TV to factory settings Possible Solutions Refer to the System Setup section for instruction on how to access the Reset All option No picture no sound Make sure the power cord is plugged in Be sure the power is on by pressing the ON OFF button on the remote control Choose an alternate channel using the CHANNEL UP DOWN ARROW KEYS Poor or no picture good sound Refer to the System Setup section for instruction on how to access the Picture Menu Adjust the options as instructed to improve the picture quality Check the antenna and or cable connections Good picture no sound Press the volume up key o
8. to increase the density and the VOLUME DOWN ARROW to decrease the density of the menus on the screen 30 DURATION Selecting DURATION will display a numeric indicator below the menu display Using the VOLUME ARROW KEYS on the remote control the display duration time of the setup menus can be modified Use the VOLUME UP ARROW to increase the dis play duration time and the VOLUME DOWN ARROW to decrease the display duration time of the menus on the screen RESET U Position H Position Halftone Reset Selecting RESET will reset all OSD Control Menu options to the factory default settings EXIT Selecting EXIT will save and close the system setup menus PicTURE MENU Selecting the PICTURE menu will display options to modify current display quality settings including CONTRAST BRIGHTNESS SATURATION HUE and SHARPNESS The broadcast input type can be modified as well CONTRAST Selecting CONTRAST will display a numeric indica tor below the menu display Using the VOLUME ARROW KEYS on the remote control the picture contrast can be modified Use the VOLUME UP ARROW to increase and the VOLUME DOWN ARROW to decrease the contrast Information cS TU Install Lansuase O50 Control CC Cartion Text O Reset All X Erisht amp Saturation Hue Sharrhess J Input O Reset 31 SYSTEM SETUP PICTURE MENU CONTINUED BRIGHT Selecting BRIGHT will display a numeric indicator below the menu di
9. 0601 West Belmont Avenue Franklin Park Illinois 60131 U S A Telephone 1 847 288 3300 FAX 1 847 288 3762 LIFE FITNESS UK LTD Queen Adelaide Ely Cambs CB7 4UB UNITED KINGDOM Telephone 44 1 353 666 017 FAX 44 1 353 666 018 LIFE FITNESS JAPAN Nippon Brunswick Bldg 8F 5 27 7 Sendagaya Shibuya Ku Tokyo Japan 151 0051 Telephone 81 3 3359 4309 FAX 81 3 3359 4307 M051 00K32 B003 NOTE This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference with radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antennas Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiv er is connected e Consult the dealer or an ex
10. BLE into the notch as shown Place the REAR CONSOLE into position against the FRONT CONSOLE and secure it with the eight previously removed SCREWS CAUTION Do not pinch the POWER CORD COAXIAL CABLE or REMOTE CONTROL CABLE when installing the REAR CONSOLE Replace and secure the MOTOR COVER using the four previously removed SCREWS Tighten the SCREWS securely Replace the LEFT LOWER HANDLEBAR ENDCAP Be sure EL the trays snap securely into position Remove the LEFT and RIGHT UPPER HANDLEBAR ENDCAPS and discard them Position the BRACKET TUBE B as shown and slide the ends into the HANDRAILS C until fully seated Install the four SET SCREWS D into the BRACK ET TUBE MOUNTING ARMS and tighten the SET SCREWS securely Attach the ENTERTAINMENT CONSOLE E to ag A the UPPER MOUNTING PLATE F using four SCREWS G Tighten the SCREWS to 6 8 in lbs Do not overtighten the SCREWS Connect the COAXIAL CABLE and POWER CABLE to the rear of the ENTERTAINMENT CONSOLE E as shown under Console Cable Connections at the end of this section INSTALLATION MobELs 97TI 95T1 93T TREADMILLS TooLs REQUIRED Standard Screwdriver Phillips Screwdriver Metric Hex Key Set Adjustable Wrench Side Cutters Flexible Fish Tape 1 Remove the four SCREWS securing the MOTOR COVER Set the MOTOR COVER and SCREWS aside 2 Remove the SCREW securing the LEFT LOWER UPRIGHT COVER Remove the LEFT LOWER UPRIGHT COVE
11. CD MOUNTING BRACKET With the mountin holes in the tube facing downward slide the tube portion of the LCD CONSOLE MOUNTING BRACKET into the top of the DISPLAY CONSOLE SUPPORT Align the inserts in the tube with the mouting holes on the underside of the DISPLAY CONSOLE SUPPORT Secure the LCD MOUNTING BRACKET using tow SCREWS Tighten the screws securely CAUTION Do not to pinch and cables when inserting the LCD MOUNTING BRACKET into the DISPLAY CONSOLE SUPPORT Position the DISPLAY CONSOLE near the DISPLAY CONSOLE SUPPORT and re connect all CONNEC TORS to the rear of the DISPLAY CONSOLE Place the DISPLAY CONSOLE onto the DISPLAY CONSOLE SUPPORT and secure it using the four previously removed SCREWS Tighten the SCREWS to 6 8 in lbs Do not overtighten the SCREWS CAUTION Do not pinch any wires when assembling the DISPLAY CONSOLE to the DISPLAY CONSOLE SUPPORT Position the ACCESSORY TRAY at the top of the MONOCOLUMN Carefully slide the ACCESSORY TRAY into the MONOCOLUMN and secure it using the two previously removed SCREWS Tighten the SCREWS to 6 8 in lbs Do not overtighten the SCREWS NOTE Feed any excess REMOTE CONTROL CABLE into the MONOCOLUMN CAUTION Do not pinch any wires when inserting the ACCESSORY TRAY into the MONOCOLUMN Attach the ENTERTAINMENT CONSOLE to the UPPER MOUNTING PLATE using four SCREWS Tighten the SCREWS to 6 8 in lbs Do not overtighten the SCREWS Connect the COAXIAL CABLE POWER CABLE and REMOTE CABLE to t
12. CORD and COAXIAL CABLE through the channel located at the top of the spacer Align the LOCATING TABS of the MOUNTING BRACKET with the tab slots and position the MOUNTING BRACKET into the center chan nel of the SPACER Slide the MOUNTING BRACKET upward until it locks solidly in the SPACER Secure the MOUNTING BRACKET to the SPACER using two FLAT HEAD SCREWS Tighten the SCREWS secure ly Position the DISPLAY CONSOLE near the MOUNTING BRACKET and re connect all CONNECTORS to the rear of the DISPLAY CONSOLE Place the DISPLAY CONSOLE onto the MOUNTING BRACKET and secure it using the four new 1 1 2 SCREWS supplied Tighten the SCREWS to 6 8 in lbs Do not overtight en the SCREWS CAUTION Do not pinch any wires when assembling the DISPLAY CONSOLE to the MOUNTING BRACKET Attach the ENTERTAINMENT CONSOLE to the UPPER MOUNTING PLATE using four SCREWS Tighten the SCREWS to 6 8 in lbs Do not overtighten the SCREWS Connect the COAXIAL CABLE POWER CABLE and REMOTE CABLE to the rear of the ENTERTAINMENT CONSOLE as shown under Console Cable Connections at the end of this section CABLE TIE any excess cable together behind the ENTERTAINMENT CONSOLE and position the cables between the ENTERTAINMENT CONSOLE BRACKET and the DISPLAY CONSOLE Reverse STEPS 1 through 3 to return the RIGHT SHROUD SEAT POST SHROUDS and RIGHT CRANK ARM to their proper positions Tighten the CRANK ARM SCREWS to 15 20 ft lbs 11 INSTALLATION MobeLs 9500
13. F button on the remote control Wait at least five seconds before proceeding To access the system setup menus press and hold the ON OFF button on the remote control for five seconds The main system setup menu will appear Use the VOLUME ARROW KEYS on the remote control to scroll through the available option Use the CHANNEL DOWN ARROW KEY on the remote control to select an option Use the UP CHANNEL ARROW KEY on the remote control to step backwards through selected menu options The menu s will automatically close after ten sec ond of inactivity INFORMATION MENU Selecting the INFORMATION menu will display the current system settings NOTE No information can be changed from this menu TV INSTALL MENU Selecting TV INSTALL will display options to modify current signal settings 26 CS TU Install Lansuase oso OSD Control loo Picture CC Cartion Text O Reset All Source NTSC H Frea 15 7 khz U Frey Gp hz Usase 12 6 hrs Fel Revi63 Information eo TU Install Lansuase OSD Control Picture CC Cartion Text dc Reset All COUNTRY Selecting COUNTRY will display a menu from which available coutries can be selected Selecting the proper country ensures the receiver is configured for the correct broadcast type Use the VOLUME ARROW KEYS on the remote control to highlight either next or back in the COUN TRY menu Use the CHANNEL DOWN ARROW KEY to progress through the availab
14. HER INFORMATION SPECIFICATIONS Television system Channel coverage Antenna Screen Size Power requirements External Power Supply Headphone Jack Power Consumption Broadcast Capabilities LCD Console Dimensions Length Width Depth Weight SERVICE CONTACTS American TV standard NTSC VHF 2 13 UHF 14 69 CATV 1 125 75 ohm external antenna terminal for VHF UHF 12 1 in Diagonal 800 x 600 TFT LCD 100V 240v 50 60 Hz 12v DC 300 milliwatt 3 5mm Stereo 12 v 1 5 amp DC NTSC M PAL I PAL B G SECAM L 12 in 12 cm 12 in 12 cm 12 in 12 cm 109 Ibs 2 oz 49 5 kg For Product Service within the United States and Canada Telephone 1 847 451 0036 FAX 1 847 288 3702 Toll free telephone 800 351 3737 For Product Service Internationally Life Fitness Europe GmbH Germany Telephone 49 089 317 751 66 FAX 49 089 317 751 38 Life Fitness UK LTD Telephone 44 1353 665 507 FAX 44 1353 666 719 Life Fitness Atlantic BV Europe Middle East amp Africa except local LF offices Life Fitness Benelux Telephone 31 180 646 666 FAX 31 180 646 699 Life Fitness Italia S R L Telephone 800 438 836 FAX 39 0457 238 197 Life Fitness Austria Vertriebs GmbH Telephone 43 1615 7198 FAX 43 1615 7198 20 36 Life Fitness Asia Pacific Ltd Asia amp Australia except local LF offices Telephone 852 2891 6677 FAX 852 2575 6001 Life Fitness Latin America
15. HR 9100 8500 95S1 93S 90S STAIRCLIMBERS Toots REQUIRED Phillips Screwdriver 1 8 Allen Wrench Side Cutters Flexible Fish Tape 1 Remove the four SCREWS securing the MONOCOLUMN SHROUD to the MAIN SHROUDS Set the SCREWS aside Raise the MONOCOLUMN SHROUD upward off of the MAIN SHROUDS 2 Remove the five SCREWS securing the LEFT SHROUD to the RIGHT SHROUD Remove the LEFT SHROUD and set it and the SCREWS aside 3 Remove the seven SCREWS securing the RIGHT SHROUD to the LEFT SHROUD Set the SCREWS and SHROUD aside 4 Remove the four SCREWS securing the DISPLAY CONSOLE to the CONSOLE MOUNTING PLATE Carefully raise the DISPLAY CONSOLE from the MOUNTING PLATE and disconnect all CONNECTORS Note the locations of all CONNECTORS Set the DISPLAY CONSOLE and SCREWS aside 5 Locate the COAXIAL CABLE and FEMALE FEMALE COUPLER Attach the FEMALE FEMALE COUPLER to one end of the COAXIAL CABLE 6 With the POWER SUPPLY and the female connector end of the COAXIAL CABLE located near the FRONT STABILIZER route the cables together along the FRAME as shown using CABLE TIES at the locations indi cated The cables should be taught secure and free of the alternator and any moving parts Be sure the CABLE TIES are pulled tight and trim the excess CABLE TIES Secure the POWER SUPPLY to the FRONT STABILIZER using two CABLE TIES as shown 7 Using a Flexible Fish Tape feed the POWER SUPPLY CORD and COAXIAL CABLE male connector end up throu
16. LE TIE at the location shown 8 Locate the SPACER With the SPACER oriented as shown feed all the previously removed CONNECTORS POWER SUPPLY CORD and COAXIAL CABLE through the large center hole in the SPACER Slide the SPACER onto the DISPLAY CONSOLE MOUNTING PLATE making sure the top of the SPACER hooks over the top of the DIS PLAY CONSOLE MOUNTING PLATE Align the mounting holes of the SPACER and DISPLAY CONSOLE MOUNT ING PLATE Push excess cable into the MONOCOLUMN leaving approximately 12 of cable extending from the SPACER 14 10 11 12 13 Locate the MOUNTING BRACKET With the MOUNTING BRACKET oriented as shown feed all the CONNECTORS through the large center hole in the MOUNTING BRACKET Route the POWER SUPPLY CORD and COAXIAL CABLE through the channel located at the top of the spacer Align the LOCATING TABS of the MOUNTING BRACKET with the tab slots and position the MOUNTING BRACKET into the cen ter channel of the SPACER Slide the MOUNTING BRACKET upward until it locks solidly in the SPACER Secure the MOUNTING BRACKET to the SPACER using two FLAT HEAD SCREWS Tighten the SCREWS securely Position the DISPLAY CONSOLE near the MOUNTING BRACKET and re connect all CONNECTORS to the rear of the DISPLAY CONSOLE Place the DISPLAY CONSOLE onto the MOUNTING BRACKET and secure it using the four new 1 1 2 SCREWS supplied Tighten the SCREWS to 6 8 in lbs Do not overtight en the SCREWS CAUTION
17. LIO Entertainment System User manual CORPORATE HEADQUARTERS 10601 West Belmont Avenue Franklin Park Illinois 60131 U S A 847 288 3300 FAX 847 288 3703 800 735 3867 Toll free within U S A Canada INTERNATIONAL OFFICES LIFE FITNESS ASIA PACIFIC LTD Room 2610 Miramar Tower 132 Nathan Road Tsimshatsui Kowloon HONG KONG Telephone 852 2891 6677 FAX 852 2575 6001 LIFE FITNESS ATLANTIC BV LIFE FITNESS BENELUX Bijdorpplein 25 31 2992 LB Barendrecht THE NETHERLANDS Telephone 31 180 646 666 FAX 31 180 646 699 LIFE FITNESS BENELUX NV Parc Industriel de Petit Rechain 4800 Verviers BELGIUM Telephone 32 87 300 942 FAX 32 87 300 943 LIFE FITNESS DO BRAZIL Av Dr Dib Sauaia Neto 1478 Alphaville Barueri SP 06465 140 BRAZIL Telephone 55 11 4193 8282 FAX 55 11 4193 8283 LIFE FITNESS AUSTRIA Vertriebs GmbH Hintschiggasse 1 1100 Vienna AUSTRIA Telephone 43 1 61 57 198 FAX 43 1 61 57 198 20 LIFE FITNESS IBERIA Pol Ind Moli dels Frares c C n 12 08620 Sant Vicen dels Horts Barcelona Espana Telephone 34 93 672 4660 FAX 34 93 672 4670 LIFE FITNESS EUROPE GMBH Siemensstrasse 3 85716 Unterschleissheim GERMANY Telephone 49 89 31 77 51 0 FAX 49 89 31 77 51 99 LIFE FITNESS ITALIA S R L Via San Pieretto 37010 AFFI Verona ITALY Telephone 39 045 7238204 FAX 39 045 7238197 LIFE FITNESS LATIN AMERICA and CARIBBEAN 1
18. NTING PLATE Carefully raise the DISPLAY CONSOLE from the MOUNTING PLATE and disconnect all CONNECTORS Note the locations of all CONNECTORS Set the DISPLAY CONSOLE and SCREWS aside 5 Remove the lower four MONOCOLUMN SCREWS Carefully raise the UPPER MONOCOLUMN ASSEM BLY from the LOWER MONOCOLUMN Without straining the MAIN WIRE HARNESS pivot the UPPER MONOCOLUMN ASSEMBLY downward and set it next to the BASE unit as shown 6 Remove the four UPPER MONOCOLUMN SCREWS and remove THE MONOCOLUMN COUPLER Remove the two SCREWS securing one side of the MONOCOLUMN COUPLER SHROUD as shown 7 Locate the COAXIAL CABLE and FEMALE FEMALE COUPLER Attach the FEMALE FEMALE COUPLER to one end of the COAXIAL CABLE 8 With the POWER SUPPLY and the female connector end of the COAXIAL CABLE located near the FRONT STABI LIZER route the cables together along the FRAME as shown using CABLE TIES at the locations indicated The cables should be taught secure and free of the alternator and any moving parts Secure the POWER SUPPLY to the FRONT STABILIZER using two CABLE TIES as shown Be sure the CABLE TIES are pulled tight and trim the excess CABLE TIES 9 Using a Flexible Fish Tape feed the POWER SUPPLY CORD and COAXIAL CABLE male connector end through the UPPER MONOCOLUMN ASSEM BLY along side the MAIN WIRE HARNESS Leave approximately 12 of both cables extending from the DISPLAY CONSOLE MOUNTING PLATE INSTALLATION
19. OWN ARROW KEY to accept the selection Hext Save Hext gave Information co TU Install OS Control foo Picture CC Cartion Text O Reset All Italian 29 SYSTEM SETUP OSD ON SCREEN DisPLAY CONTROL MENU Selecting the OSD CONTROL menu will display options to modify current On Screen Display settings including VERTICAL POSITION HORIZONTAL POSITION HALFTONE and DURATION VERTICAL POSITION Selecting VERTICAL POSITION will display a numeric indicator below the menu display Using the VOLUME ARROW KEYS on the remote control the vertical position of where the setup menus appear can be modified Use the VOLUME UP ARROW to move the menu upward and the VOLUME DOWN ARROW to move the menu downward on the screen HORIZONTAL POSITION Selecting HORIZONTAL POSITION will display a numeric indicator below the menu display Using the VOLUME ARROW KEYS on the remote control the horizontal position of where the setup menus appear can be modified Use the VOLUME UP ARROW to move the menu to the right and the VOLUME DOWN ARROW to move the menu to the left on the screen HALFTONE Information co TU Install Lansuyase Picture CC Cartion Text On Reset All LU Position H Position Duration Reset Exit Selecting HALFTONE will display a numeric indicator below the menu display Using the VOL UME ARROW KEYS on the remote control the density of the setup menus can be modified Use the VOLUME UP ARROW
20. PLATE Locate the MOUNTING BRACKET With the MOUNT ING BRACKET oriented as shown feed all the CON NECTORS through the large center hole in the MOUNTING BRACKET Route the power supply cord and coaxial cable through the channel located at the top of the spacer Align the LOCATING TABS of the MOUNTING BRACKET with the tab slots and position the MOUNTING BRACKET into the center channel of the SPACER Slide the MOUNTING BRACKET upward until it locks solidly in the SPACER Secure the MOUNTING BRACKET to the SPACER using two FLAT HEAD SCREWS Tighten the SCREWS secure ly Locate the REMOTE CONTROL Remove the two HORIZONTAL CABLE TIES H for a VERTICAL V installation Remove the four SCREWS securing the TOP POLAR COVER to the BOTTOM POLAR COVER and remove the TOP POLAR COVER Locate the provided new TOP POLAR COVER with mounting slots Carefully pull the lead end of each CABLE TIE until the receptor end meets the bottom of the REMOTE CONTROL Feed both lead ends of the CABLE TIES throught the bottom mounting slots of the TOP POLAR COVER as shown Loop the lead ends of the CABLE TIES upward through the top mounting slots Feed the CABLE TIES through until the bottom of the REMOTE CONTROL contacts the TOP POLAR COVER Feed the lead ends of the CABLE TIES through the receptor ends and slowly pull them tight alternating between the two CABLE TIES The remote control should now be snug against the TOP POLAR COVER Trim the excess leng
21. R and set it and the SCREW aside 3 Remove the two SCREWS securing the LEFT FRONT FRAME CAP Remove the LEFT FRONT FRAME CAP and set it and the SCREWS aside 4 Remove the eight SCREWS from the rear of the console securing the FRONT CONSOLE to the REAR CONSOLE Carefully lift the FRONT CONSOLE and remove all CONNECTORS Note the locations of all CONNECTORS Set the FRONT CONSOLE and SCREWS aside 5 Remove the four SCREWS from each of the ACCESSORY TRAYS Lift the ACCESSORY TRAYS from the UPRIGHTS Set the ACCESSORY TRAYS and SCREWS aside 6 Remove the two SCREWS from each of the INSIDE HANDLEBAR COVERS Remove the OUTSIDE HANDLEBAR COVERS and set them aside Slide the INSIDE HANDLEBAR COVERS inward and remove the two screws secur ing each end of the ERGO CROSSBAR Slowly raise the ERGO CROSSBAR upward from between the HANDLE BARS Disconnect the 2 PIN LIFEPULSE CONNECTORS Set the ERGO CROSSBAR and SCREWS aside 7 Remove the LEFT INNER HANDLEBAR COVER from the ERGO CROSSBAR Create a 1 2 wide by 1 4 deel notch at the front of the ERGO CROSSBAR hole as shown TA pr LY S A 8 Starting approximately 1 2 from the top center of the GR REAR CONSOLE Create a 1 2 wide by 3 8 deep slot in the REAR CONSOLE top 9 Locate the REMOTE CONTROL Remove the two HORI ZONTAL CABLE TIES H for a VERTICAL V installation Position the remote control near the left end of the ergo cross bar
22. and Caribbean Telephone 1 847 288 3964 FAX 1 847 288 3886 Life Fitness Brazil Telephone 55 11 4193 8282 FAX 55 11 4193 8283 Life Fitness Japan Telephone 81 3 3359 4309 FAX 81 3 3359 4307 Life Fitness Iberia Spain Telephone 34 93 672 4660 FAX 34 93 672 4670 M051 00K32 B003
23. cable entry as practical Antenna Grounding According to the NEC Antenna Grounding According to the National Electrical Code ANSI NFPA 70 1 2 3 4 5 6 7 Antenna lead in wire Antenna discharge unit NEC Section 810 20 Grounding conductors NEC Section 810 21 Ground clamp Power service grounding electrode system NEC Article 250 Part H Ground clamp Electric service equipment REMOTE CONTROL CABLE TIE ORIENTATION The remote control is shipped with four cable ties pre 7 AY installed Only two are required either vertically or hori zontally for installation on any given product For a ver tical installation carefully remove the horizontal cable ties H For a horizontal installation carefully remove the vertical cable ties V MopeLs 9500HR 9100 8500 95C1 93C 90C UPRIGHT EXERCISE BIKES Toots REQUIRED Phillips Screwdriver Side Cutters 1 8 Allen Wrench T 20 Torx Driver T 30 Torx Driver T 45 Torx Driver Flexible Fish Tape 1 Remove the three SCREWS securing the user RIGHT CRANK ARM Set the SCREWS and CRANK ARM aside 2 Remove the SCREW securing the SEAT POST SHROUDS Remove the SEAT POST SHROUDS and set them aside 3 Remove the seven SCREWS securing the RIGHT SHROUD to the LEFT SHROUD Set the SCREWS and SHROUD aside 4 Remove the four SCREWS securing the DISPLAY CONSOLE to the CONSOLE MOU
24. e POWER CORD COAXIAL CABLE and REMOTE CONTROL CORD oriented in the TOP CONSOLE NOTCH as shown replace the CONSOLE CONNECTORS and secure the FRONT CONSOLE using the eight previously removed SCREWS Tighten the SCREWS securely OUEN IW Dy um um Replace the ACCESSORY TRAYS Be sure the trays snap securely into position Replace and secure the MOTOR COVER using the four previously removed SCREWS Tighten the SCREWS securely Replace the LEFT LOWER HANDLEBAR ENDCAP Be sure the trays snap securely into position Remove the LEFT and RIGHT UPPER HANDLEBAR ENDCAPS and discard them Position the BRACKET TUBE B as shown and slide the ends into the HANDRAILS C until fully seated Install the four SET SCREWS D into the BRACKET TUBE MOUNTING ARMS and Se D tighten the SET SCREWS securely Ce Ere Attach the ENTERTAINMENT CONSOLE E to the UPPER MOUNTING PLATE F using four SCREWS G Tighten the SCREWS to 6 8 in lbs Do not overtighten the SCREWS Connect the COAXIAL CABLE and POWER e CABLE to the rear of the ENTERTAINMENT lt CONSOLE E as shown under Console Cable Connections at the end of this sec tion INSTALLATION MobeLs 9700HR 9500HR 9100 9000 TREADMILLS Toots REQUIRED Standard Screwdriver Phillips Screwdriver Metric Hex Key Set Adjustable Wrench Side Cutters Flexible Fish Tape 1 20 Remove the eight SCREWS securing the REAR CONSOLE to the FRONT CONSOLE Set the REAR CONSOLE and SCREWS a
25. e mesure d entretien AVERTISSEMENT Pour r duire les risques de br lures d incendies de d charges lectriques ou de blessures chaque appareil doit absolument tre branch sur une prise lectrique correctement mise la terre AVERTISSEMENT Pour pr venir les blessures ce produit doit tre solide ment fix conform ment aux instructions d installation e Ne jamais faire fonctionner un produit Life Fitness dont la fiche ou le cordon d alimentation est endommag ni aucun appareil qui serait tomb ou aurait t endommag ou m me partiellement plong dans l eau Si cela se produit communiquer avec le service la clien t le de Life Fitness de la mani re indiqu e la rubrique Coordonn es des r parateurs agr s la fin du pr sent guide e Placer l appareil de fa on a ce que l utilisateur ait acc s la fiche du cordon d alimentation e Tenir le cordon d alimentation l cart de toute surface chauff e Ne pas tirer l appareil par le cordon d alimentation ne pas utiliser le cordon comme poign e e Si le cordon d alimentation lectrique est endommag il doit tre remplac par le fabricant par un r parateur agr ou par une personne qualifi e afin d viter tout danger e Ne pas utiliser ce produit dans des salles o des vaporisateurs a rosols sont employ s ou bien o de l oxyg ne est administr Ces substances cr ent des risques de combustion et d explosion e Toujours suivre
26. gh the MONOCOLUMN ASSEMBLY along side the MAIN WIRE HAR NESS Leave approximately 12 of both cables extending from the DISPLAY CONSOLE MOUNTING PLATE 8 Locate the REMOTE CONTROL Remove the two HORIZONTAL CABLE TIES H for a VERTICAL V installation Secure the REMOTE CONTROL to the top of the HANDLEBAR as shown Be sure the CABLE TIES are pulled tight and trim the excess CABLE TIES 9 Loop the CONNECTOR CABLE under the HANDLEBAR and secure it to the top of the CONSOLE EXTENSION TUBE using one CABLE TIE at the location shown 10 11 12 13 14 15 16 Locate the SPACER With the SPACER oriented as shown feed all the previously removed CON NECTORS POWER SUPPLY CORD and COAXIAL CABLE through the large center hole in the SPACER Slide the SPACER onto the DISPLAY CONSOLE MOUNTING PLATE mak ing sure the top of the SPACER hooks over the top of the DISPLAY CONSOLE MOUNTING PLATE Align the mounting holes of the SPAC ER and DISPLAY CONSOLE MOUNTING PLATE Push excess cable into the MONOCOL UMN leaving approximately 12 of cable extend ing from the SPACER Locate the MOUNTING BRACKET With the MOUNTING BRACKET oriented as shown feed all the CON NECTORS through the large center hole in the MOUNTING BRACKET Route the POWER SUPPLY CORD and COAXIAL CABLE through the channel located at the top of the spacer Align the LOCATING TABS of the MOUNTING BRACKET with the tab slots and positio
27. he rear of the ENTERTAINMENT CONSOLE as shown under Console Cable Connections at the end of this section CABLE TIE any excess cable together behind the ENTERTAINMENT CONSOLE and position the cables between the ENTERTAINMENT CONSOLE BRACKET and the DISPLAY CONSOLE Replace the DISPLAY COSOLE SUPPORT COVER and secure it using the two previously removed SCREWS Locate the NEW TOP CAP Place the NEW TOP CAP into position at the top of the DISPLAY COSOLE SUPPORT COVER Be sure the TOP CAP snaps securely in place 17 INSTALLATION MobeLs 9000 8500 91Ti 90T TREADMILLS Toots REQUIRED Standard Screwdriver Phillips Screwdriver Metric Hex Key Set Adjustable Wrench Side Cutters Flexible Fish Tape 1 2 3 4 Remove the four SCREWS securing the MOTOR COVER Set the MOTOR COVER and SCREWS aside Remove the PUNCH TAB located in the bottom front left of the MOTOR PAN Remove the LEFT LOWER HANDLEBAR ENDCAP and set it aside Remove the two ACCESSORY TRAYS by pressing inward firmly at the top rear of each ACCESSORY TRAY and pushing the trays upward Remove the eight SCREWS from the rear of the console securing the FRONT CONSOLE to the REAR CONSOLE Remove the two PLASTIC RIVOTS located on the lower inner sides of the FRONT CONSOLE Carefully lift the FRONT CONSOLE and remove all CONNECTORS Note the locations of all CONNECTORS Set the FRONT CONSOLE and SCREWS aside Locate the COAXIAL CABLE and FEMALE FEMALE COUPLER Attach the
28. le Fish Tape feed the POWER SUPPLY CORD and COAXIAL CABLE male connector end up through the FRONT FRAME ACCESS HOLE and LEFT UPRIGHT Route the POWER CORD and COAXIAL CABLE through the cable guide and through to the top of the DISPLAY CONSOLE With the POWER CORD COAXIAL CABLE and REMOTE CONTROL CORD oriented in the TOP CON SOLE SLOT as shown replace the CONSOLE CONNECTORS and secure the FRONT CONSOLE using the eight previously removed SCREWS Tighten the SCREWS securely NOTE AN CABLES should be routed throught the CABLE GUIDE located at the lower left of the REAR CONSOLE Be careful not to pinch the LIFEPULSE CABLE when replacing the ERGO CROSSBAR 23 INSTALLATION 20 21 22 23 24 If through holes in the four CONSOLE BOSSES are not present use a 5 16 drill from the top center of the four CONSOLE BOSSES to create through holes Locate the four RETAINING SPACERS G Position the RETAINING SPACERS over the CONSOLE BOSSES E as shown Be sure the RETAINING SPACERS are fully nested over the structural ribs inside the CONSOLE F Position the BRACKET TUBE D with the MOUNTING PLATES facing upward as shown Position two SCREWS E on either side throught the CONSOLE BOSSES Install four NYLOCK NUTS H onto the installed SCREWS E securing the RETAINING SPACERS and BRACKET TUBE to the CONSOLE Tighten the NYLOCK NUTS securely Do not over tighten the NYLOCK NUTS Replace the RIGHT and LEFT ACCESSORY TRAYS B
29. le countries When the desired country appears use the VOL UME ARROW KEYS to highlight the SELECT option and press the CHANNEL DOWN ARROW KEY to accept the selection Available Countries Argentina Aruba Australia Austria Bahamas Bahrain Bangladesh Barbados Belgium Bonaire Bosnia Brazil Caribbean Cayman Islands Chile China Colombia Costa Rica Curacao Cyprus Czech Republic Dominican Republic Ecuador Egypt El Salvador Ethiopia Finland France Germany Ghana Greece Guatemala Honduras Hong Kong Hungary Iceland India Indonesia Ireland Israel Italy Japan Jordan Kenya Korea Kuwait Lebanon Malaysia Mexico Moldova Nepal New Zealand Nicaragua Norway Pakistan Panama Peru Philippines Poland Portugal Puerto Rico Country System Hir Cable Scan Channel Add Channel Remove Channel Hest Back Select Qatar Romania Russia Saudi Arabia Singapore Slovakia South Africa Spain Sri Lanka St Martin Sweden Switzerland Syria Taiwan Thailand Turkey United Arab Emirates United Kingdom Venezuela 27 SYSTEM SETUP SYSTEM Selecting SYSTEM displays a selection of compat able PAL broadcast types This input will override Counters settings made when choosing a COUNTRY in the Sus Lem TV INSTALL menus HirrCable Scan Channel Add Channel Remove Channel Selecting the wrong input will result in a distorted broadcast picture The program display is no
30. les instructions sur le produit pour s assurer de son fonctionnement ad quat e Ne jamais ins rer aucun objet dans les ouvertures du produit Life Fitness Si un objet tombe a l int rieur du produit Life Fitness le d brancher et extraire l objet soigneusement pendant que l appareil est d branch S il est impossible d atteindre l objet communiquer avec le service la client le de Life Fitness e Ne pas utiliser ce produit l ext rieur pr s d une piscine ou dans des endroits tr s humides Ne pas exposer ce produit des liquides qui s gouttent ni des claboussures Si le pro duit est en contact avec des liquides communiquer avec le service la client le de Life Fitness e Ne jamais faire fonctionner d appareil Life Fitness dont les orifices d a ration seraient blo qu s Les garder exempts de peluches de cheveux ou de toute obstruction e _ Utiliser ce produit uniquement pour les fins auxquelles il est destin et de la mani re d crite dans le pr sent manuel Ne pas utiliser d accessoires qui ne sont pas recommand s par le fabricant CONSERVER CES INSTRUCTIONS POUR TOUT USAGE ULT RIEUR INSTALLATION Note to the CATV Installer This reminder is provided to call the CATV system installer s attention to Article 820 40 of the NEC that provides guidelines for proper grounding and in particular specifies that the cable ground shall be connected to the grounding system of the building as close to the point of
31. n Menu 17 RRE UO TEE 17 OSD Control Menu 20 Picture Ment LES MR A A da re nn ace eue de 22 Caption Text Menu 24 RescrAll airada aa ce nn 24 6 Other Information 0c ee eee eee eee eee 25 Troubleshooting 2 44 ee teree ee A ath ee eee bee pe Ae ee AE eo 25 Specifications g ere sated leg hae Me done a dE ee 26 Service ee le CES 26 2003 Life Fitness a division of Brunswick Corporation All rights reserved IMPORTANT SAFETY INSTRUCTIONS DANGER To reduce the risk of electrical shock always unplug this Life Fitness product before cleaning or attempting any maintenance activity WARNING To reduce the risk of burns fire electric shock or injury it is impera tive to connect each product to a properly grounded electrical outlet WARNING To prevent injury this product must be securely attached in accor dance with the installation instructions Never operate a Life Fitness product if it has a damaged power cord or electrical plug or if it has been dropped damaged or even partially immersed in water If this occurs contact Life Fitness Customer Support Services as outlined in Service Contacts at the end of this manu al Position this product so that the AC power cord plug is accessible to the user Keep the power cord away from heated surfaces Do not pull the equipment b
32. n the MOUNTING BRACKET into the center chan nel of the SPACER Slide the MOUNTING BRACKET upward until it locks solidly in the SPACER Secure the MOUNTING BRACKET to the SPACER using two FLAT HEAD SCREWS Tighten the SCREWS secure ly Position the DISPLAY CONSOLE near the MOUNTING BRACKET and re connect all CONNECTORS to the rear of the DISPLAY CONSOLE Place the DISPLAY CONSOLE onto the MOUNTING BRACKET and secure it using the four new 1 1 2 SCREWS supplied Tighten the SCREWS to 6 8 in lbs Do not overtight en the SCREWS CAUTION Do not pinch any wires when assembling the DISPLAY CONSOLE to the MOUNTING BRACKET Attach the ENTERTAINMENT CONSOLE to the UPPER MOUNTING PLATE using four SCREWS Tighten the SCREWS to 6 8 in lbs Do not overtighten the SCREWS Connect the COAXIAL CABLE POWER CABLE and REMOTE CABLE to the rear of the ENTERTAINMENT CONSOLE as shown under Console Cable Connections at the end of this section CABLE TIE any excess cable together behind the ENTERTAINMENT CONSOLE and position the cables between the ENTERTAINMENT CONSOLE BRACKET and the DISPLAY CONSOLE Reverse STEPS 1 through 3 to return the LEFT SHROUD and MONOCOLUMN SHROUD to their proper positions Tighten the SCREWS securely Do not over tighten the SCREWS 13 INSTALLATION MopeLs 9500HRR 9100 8500 Cross TRAINERS TooLs REQUIRED Phillips Screwdriver Side Cutters 1 8 Allen Wrench Flexible Fish Tape 1 Remove the four SCREWS sec
33. n the remote control headphones are required to hear sound No color Check the antenna and or cable connections Confirm the correct country is selected Refer to the System Setup section for instruction on how to access the country option within the TV Install Menu Refer to the System Setup section for instruction on how to access the Picture Menu Adjust the Contrast Hue and or Saturation options as instructed to improve the picture quality Only snow appears on the screen Check the antenna and or cable connections Make sure the channel selected is currently broadcasting Confirm the correct Air Cable option is selected Refer to the System Setup section for instruction on how to access the Air Cable option within the TV Install Menu Dotted lines or stripes Adjust the antenna Move the TV away from other electronic equipment Some electronic equipment creates electrical noise which can interfere with TV recep tion Double images or ghosts Check your outdoor antenna or call your cable service Unable to switch to a particular TV channel Confirm the correct Air Cable option is selected Refer to the System Setup section for instruction on how to access the Air Cable option within the TV Install Menu Perform a Scan Channel or add a channel manually Refer to the System Setup section for instruction on how to access the Scan Channel or Add Channel option within the TV Install Menu 35 OT
34. near the console edge along side the MAIN WIRE HARNESS NOTE Approximately 6 of POWER CORD and COAXIAL CABLE should extend from the top of the DISPLAY CONSOLE With the help of another person lift the UPRIGHTS and CONSOLE up and back over the UPRIGHT BRACKETS Secure the UPRIGHTS using the six previously removed BOLTS and WASHERS Tighten the BOLTS securely CAUTION Do not pinch the MAIN WIRE HARNESS POWER CORD COAXIAL CABLE or REMOTE CONTROL CABLE when installing the UPRIGHTS 20 Starting approximately 1 2 from the top center of the REAR CONSOLE Create a 1 2 wide by 3 8 deep notch in the REAR CONSOLE top Locate the REMOTE CONTROL Remove the two HOR IZONTAL CABLE TIES H for a VERTICAL V installation Secure the REMOTE CONTROL to the left end of the ERGO CROSSBAR as shown Be sure the CABLE TIES are pulled tight and trim the excess CABLE TIES Route the REMOTE CONTROL CABLE along the LEFT HANDLEBAR Secure the REMOTE CONTROL CABLE using two CABLE TIES in the loca tions shown Be sure the CABLE TIES are pulled tight and trim the excess CABLE TIES Route the remaining REMOTE CONTROL CABLE along the handlebar and up near the LEFT ACCESS HOLE of the LEFT HANDLEBAR Route the REMOTE CON TROL CABLE up alongside the POWER CORD and COAXIAL CABLE Locate the REAR CONSOLE and SCREWS Position the REAR CONSOLE near the back of the FRONT CONSOLE Position the POWER CORD COAXIAL CABLE and REMOTE CONTROL CA
35. nect all CONNECTORS Note the locations of all CONNECTORS Set the DISPLAY CONSOLE and SCREWS aside With the POWER SUPPLY located near the FRONT STABILIZER secure the POWER SUPPLY to the FRONT STABILIZER using two CABLE TIES as shown Using a Flexible Fish Tape feed the POWER SUPPLY CORD and COAXIAL CABLE male connector end up through the MONOCOLUMN ASSEMBLY along side the MAIN WIRE HARNESS Leave approximately 12 of both cables extending from the DISPLAY CONSOLE SUPPORT Remove the SCREW securing the LEFT BULLHORN COVER Set the LEFT BULLHORN COVER and SCREW aside Remove the two SCREWS securing the LEFT BULLHORN to the LEFT BULLHORN MOUNTING PLATE Remove the LEFT BULLHORN Locate the supplied NEW LEFT BULLHORN Secure it in place using the two previously removed SCREWS Tighten the SCREWS to 15 20 ft lbs Replace the LEFT BULLHORN COVER and secure it using the previously removed SCREW Tighten the SCREW securely Locate the REMOTE CONTROL Remove the two VERTICAL CABLE TIES H for a HORIZONTAL V installation Secure the REMOTE CONTROL to the top of the MOUNTING FIN GER located on the NEW LEFT BULLHORN as shown Be sure the CABLE TIES are pulled tight and trim the excess CABLE TIES Route the REMOTE CONTROL CABLE through the MONOCOLUMN and up through the DIS PLAY CONSOLE SUPPORT alongside the POWER SUPPLY CORD and COAXIAL CABLE 13 14 15 16 17 18 19 20 Locate the L
36. perienced radio TV technician for help AM CAUTION Any changes or modifications to this equipment could void the product warranty Mise en garde tout changement ou toute modification de ce mat riel peut annuler la garantie du produit Any service other than cleaning or user maintenance must be performed by an authorized service representative There are no user serviceable parts TABLE OF CONTENTS Section Description Page 1 Important Safety Instructions 4 2 Installation EE 6 Models 9500HR 9100 8500 95Ci 93C 90C Upright Exercise Bikes 7 Models 9500HR 9100 8500 95Ri 93R 90R Recumbent Exercise Bikes 8 Models 9500HR 9100 8500 95Si 93S 90S Stairclimbers 9 Models 9500HRR 9100 8500 Cross Trainers 10 Models 97Xi 95Xi 93X 90X Crosstrainers 11 Models 9700HR 9500HR 9100 9000 Treadmills 12 Models 9000 8500 91Ti 90T Treadmills 12 Models 97Ti 95Ti 93T Treadmills 13 3 Console Cable Connections 14 4 Basic Functions 16 5 SYSteM SetUp 154485 aira homme ZE Leman eo da ied dede ZE BE pl adie deere 16 How to Access Menus 16 Informatio
37. side CAUTION Support the REAR CONSOLE when removing the SCREWS Do not let the REAR CONSOLE drop Remove the four SCREWS securing the MOTOR COVER Set the MOTOR COVER and SCREWS aside Remove the two SCREWS securing the FRONT rN LEFT FRAME CAP Set the FRONT LEFT FRAME CAP and SCREWS aside Remove the LEFT LOWER HANDLEBAR ENDCAP and set it aside Remove the six BOLTS and WASHERS securing the UPRIGHTS to the FRAME With the help of another person carefully lift the UPRIGHTS off of the UPRIGHT BRACKETS Carefully set the UPRIGHTS and CONSOLE onto the TREADMILL BASE Set the BOLTS aside CAUTION Be careful not to damage the MAIN WIRE HARNESS when lifting the UPRIGHTS AND CONSOLE from the UPRIGHT BRACKETS Be careful not to damage the PAINT when setting the UPRIGHTS AND CONSOLE on the TREADMILL BASE Locate the COAXIAL CABLE and FEMALE FEMALE COUPLER Attach the FEMALE FEMALE COUPLER to one end of the COAXI AL CABLE Locate the POWER SUPPLY and POWER CORD EXTENSION CABLE KIT Attach the POWER CORD EXTENSION as instructed in the kit Using a Flexible Fish Tape feed the POWER CORD and COAXIAL CABLE male connector end up through the LEFT FRONT FRAME PLATE LEFT UPRIGHT and out the LEFT HANDLEBAR Using the Flexible Fish Tape feed the POWER SUPPLY CORD and COAXI AL CABLE male connector end up through the LEFT HANDLEBAR and out the LEFT ACCESS HOLE located at the top of the LEFT HAN DLEBAR
38. splay Using the VOLUME ARROW KEYS on the remote control the picture brightness can be modified Use the VOLUME UP ARROW to increase and the VOLUME DOWN ARROW to decrease the brightness SATURATION Selecting SATURATION will display a numeric indi cator below the menu display Using the VOLUME ARROW KEYS on the remote control the picture saturation can be modified Use the VOLUME UP ARROW to increase and the VOLUME DOWN ARROW to decrease the saturation HUE Selecting HUE will display a numeric indicator below the menu display Using the VOLUME ARROW KEYS on the remote control the picture color hue can be modified Use the VOLUME UP ARROW to increase and the VOLUME DOWN ARROW to decrease the picture color hue 32 O Contrast amp Saturation Hue Sharrhess Input do Reset O Contrast X Brisht Hue Shareness 1 Input Reset O Contrast X Brisht 8 Saturation Hue Sharreness Input Reset SHARPNESS Selecting SHARPNESS will display a numeric indi cator below the menu display Using the VOLUME 0 Contrast ARROW KEYS on the remote control the picture XX Erisht sharpness can be modified Use the VOLUME UP amp Saturation ARROW to increase and the VOLUME DOWN Hue ARROW to decrease the picture sharpness SharrPhes Input D Reset INPUT Selecting INPUT displays a selection of compatable broadcast types This input will override settings made when choosing a COUNTRY in the TV INSTALL
39. t affected by the input selection AIR CABLE Selecting AIR CABLE will display a menu from which either standard air broadcast or cable television can Counters be selected as the input preference irrCable Scan Channel Add Channel Remove Channel SCAN CHANNEL Selecting SCAN CHANNEL will begin the automatic channel discovery sequence The system will auto matically seek and lock onto all available channels When the screen stops flashing through the avail able channels the sequence is complete 28 ADD CHANNEL Selecting ADD CHANNEL will add an available channel that has been previously removed from the viewable listing Use the ADD selection to add a channel Use the next selection to advance to the NEXT available channel Continue adding as neces sary until finished Use the SAVE selection to save the channel additions REMOVE CHANNEL Selecting REMOVE CHANNEL will remove a chan nel from the viewable listing Use the REMOVE selection to remove a channel Use the next selec tion to advance to the NEXT available channel Continue removing as necessary until finished Use the SAVE selection to save the channel removals LANGUAGE MENU Selecting LANGUAGE will display a menu from which available languages can be selected in which to display setup menus Use the VOLUME ARROW KEYS on the remote control to highlight the DESIRED language Select the NEXT option to view additional language choic es Use the CHANNEL D
40. th of CABLE TIES 20 Install the new TOP POLAR COVER to the BOTTOM POLAR COVER using the four previously removed SCREWS 21 Loop the CONNECTOR CABLE under the HANDLEBARS and secure it to the top of the CONSOLE EXTENSION TUBE using one CABLE TIE at the location shown 22 Position the DISPLAY CONSOLE near the MOUNTING BRACKET and re connect all CONNECTORS to the rear of the DISPLAY CONSOLE Place the DISPLAY CONSOLE onto the MOUNTING BRACKET and secure it using the four new 1 1 2 SCREWS supplied Tighten the SCREWS to 6 8 in lbs Do not overtight en the SCREWS CAUTION Do not pinch any wires when assembling the DISPLAY CONSOLE to the MOUNTING BRACKET 23 Attach the ENTERTAINMENT CONSOLE to the UPPER D MOUNTING PLATE using four SCREWS Tighten the SCREWS to 6 8 in lbs Do not overtighten the SCREWS ze 24 Connect the COAXIAL CABLE POWER CABLE and L REMOTE CABLE to the rear of the ENTERTAINMENT CONSOLE as shown under Console Cable Connections at the end of this section 25 CABLE TIE any excess cable together behind the ENTER TAINMENT CONSOLE and position the cables between the ENTERTAINMENT CONSOLE BRACKET and the DISPLAY CONSOLE 26 Create a notch in the lower front of the RIGHT SHROUD as shown With the POWER CORD and COAXIAL CABLE routed through the notch replace the RIGHT SHROUD and secure it to the LEFT SHROUD using the seven previously removed SCREWS Tighten the SCREWS securely do not over tighten the SCREWS
41. ure the CABLE TIES are pulled tight and trim the excess CABLE TIES 7 Using a Flexible Fish Tape feed the POWER SUPPLY CORD and COAXIAL CABLE male connector end up through the MONOCOLUMN ASSEMBLY along side the MAIN WIRE HARNESS Leave approximately 12 of both cables extending from the DISPLAY CONSOLE MOUNTING PLATE 8 Locate the REMOTE CONTROL Remove the two HORIZONTAL CABLE TIES H for a VERTICAL V installation Secure the REMOTE CON TROL to the top of the HANDLEBAR as shown Be sure the CABLE TIES are pulled tight and trim the excess CABLE TIES 9 Loop the CONNECTOR CABLE under the HANDLEBAR and secure it to the HANDLEBAR using three CABLE TIE at the locations shown 10 11 12 13 14 15 16 Locate the SPACER With the SPACER orient ed as shown feed all the previously removed CONNECTORS POWER SUPPLY CORD and COAXIAL CABLE through the large center hole in the SPACER Slide the SPACER onto the DISPLAY CONSOLE MOUNTING PLATE mak ing sure the top of the SPACER hooks over the top of the DISPLAY CONSOLE MOUNTING PLATE Align the mounting holes of the SPAC ER and DISPLAY CONSOLE MOUNTING PLATE Push excess cable into the MONO COLUMN leaving approximately 12 of cable extending from the SPACER Locate the MOUNTING BRACKET With the MOUNTING BRACKET oriented as shown feed all the CON NECTORS through the large center hole in the MOUNTING BRACKET Route the POWER SUPPLY
42. uring the DISPLAY CONSOLE to the CONSOLE MOUNTING PLATE Carefully raise the DISPLAY CONSOLE from the MOUNTING PLATE and disconnect all CONNECTORS Note the loca tions of all CONNECTORS Set the DISPLAY CONSOLE and SCREWS aside 2 Locate the COAXIAL CABLE and FEMALE FEMALE COUPLER Attach the FEMALE FEMALE COUPLER to one end of the COAXIAL CABLE 3 Locate the POWER SUPPLY and POWER CORD EXTENSION CABLE KIT Attach the POWER CORD EXTENSION as instructed in the kit 4 With the POWER SUPPLY and the female connector end of the COAXIAL CABLE located near the FRONT STABILIZER route the cables together along the FRAME as shown using CABLE TIES at the locations indi cated The cables should be taught secure and free of the alternator and any moving parts Secure the POWER SUPPLY to the FRONT STABILIZER using two CABLE TIES as shown 5 Using a Flexible Fish Tape feed the POWER SUPPLY CORD and COAXIAL CABLE male connector end up through the MONOCOLUMN ASSEMBLY along side the MAIN WIRE HARNESS Leave approximately 12 of both cables extending from the DISPLAY CONSOLE MOUNTING PLATE 6 Locate the REMOTE CONTROL Remove the two HORIZONTAL CABLE TIES H for a VERTICAL V instal lation Secure the REMOTE CONTROL to the top of the HANDLEBAR as shown Be sure the CABLE TIES are pulled tight and trim the excess CABLE TIES 7 Loop the CONNECTOR CABLE under the HANDLEBAR and secure it to the top of the CONSOLE EXTEN SION TUBE using one CAB
43. y the power cord or use the cord as a handle If the electrical supply cord is damaged it must be replaced by the manufacturer an author ized service agent or a similarly qualified person to avoid a hazard Do not use this product in areas where aerosol spray products are being used or where oxygen is being administered Such substances create the danger of combustion and explosion Always follow the product instructions for proper operation Never insert objects into any opening of the Life Fitness product If an object should drop inside unplug this Life Fitness product and carefully retrieve it while the unit is not in use If the object cannot be reached contact Life Fitness Customer Support Services Do not use this product outdoors near swimming pools or in areas of high humidity Do not expose this product to dripping or splashing liquids If the product should be exposed to liq uid contact Life Fitness Customer Support Services Never operate a Life Fitness product with the air openings blocked Keep air openings free of lint hair or any obstructing material Use this product only for its intended use as described in this manual Do not use attach ments that have not been recommended by the manufacturer SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE CONSIGNES DE SECURITE IMPORTANTES DANGER Pour r duire les risques de d charge lectrique toujours d brancher cet appareil Life Fitness avant le nettoyage ou tout

LCD Entertainment System

Contents

Download Pdf Manuals

Related Search

Related Contents