- Plasmon
Contents
1. Plasmon The Leader in Professional Data Archival Solutions The Plasmon UDO60D I 5 25 inch Optical Drive User Manual P N 800 102901 00 A PREFACE Copyright Copyright 2007 by Plasmon All rights reserved This manual and the information contained herein are the property of Plasmon United States Office European Headquarters UK Plasmon Plasmon Data Limited 4425 ArrowsWest Drive Whiting Way Colorado Springs CO 80907 3489 Melbourn Herts SG8 6EN Disclaimer Plasmon makes no representation or warranties with respect to the contents of this document and specifically disclaims any implied warranties of merchantability or fitness for any particular purpose Furthermore Plasmon reserves the right to revise this publication without obligation of Plasmon to notify any person or organization of such revision or changes Trademark Notices Plasmon is a U S registered trademark of Plasmon All other product names are trademarks or registered trademarks of their respective owners Revision History Revision Date Description A 3 07 Initial release NOTE The most current information about this product is available on the Plasmon web site www plasmon com Plasmon UDO60D Drive User Manual Preface Document Revision A Page 1 Conventions Used WARNING A WARNING is used to alert the reader to situations or conditions that could potentially result in personal injury fire hazard or equipment damage WARNUNG E2. Along with the SCSI ID switches on the back of the UDO60D enclosure is a switch number five for setting TIN Enable Turning on TIN Target Initiated Negotiations enables the drive to negotiate Wide and Synchronous on the SCSI bus The default setting for this switch is off since target devices do not normally initiate negotiation Some platforms drivers or adapter cards may fail to re negotiate correctly under certain conditions In this event the host computer cannot communicate with the drive over the SCSI bus Enabling TIN allows the drive to re negotiate and maintain communication with the host If communication is lost on power cycles or drive resets at host boots setting the TIN Enable switch may solve the problem In general Microsoft systems may need TIN enabled AIX Unix and Linux systems typically need TIN disabled Plasmon UDO60D I Drive User Manual Getting Started Document Revision A Page 19 Setting Up the UDO6OI When handling the UDO6OI use full anti static precautions as outlined in the Unpacking section To install the drive in an enclosure follow these steps 1 Ensure that the power cable is correctly wired and that power is within the unit s specifications 2 Ensure that adequate ventilation and cooling is provided Plasmon recommends that filtered air is blown from the rear to front of the drive For USB Connectivity If the drive is connecting to a USB interface follow these steps 1 Mount th
3. oooooococoooooo ee eee 27 European Notice eoaronrn ra aa aa ade 27 Australia New Zealadd ooo 28 Jarabe a As ee AS 28 Product Safety Standards c2iadeceue paar la 28 UDOSOL 00 reu na eta conta lars ek on ace Soe aran ake Sos eaten E 28 UDO GOD kra rem rm ae da a ed ee 28 Laser Safety Notice be awe twee td Be east OGG Redee eed ee atagenwWade 29 COREL REquiallons cross dd babes Bob eee hes FOSS ble Ee EART a 30 Power Cord Set Selection 0 0 00 eee teen eee 30 CONTACTING PLASMON iia oo nino ers as 31 Table of Contents Plasmon UDO60D I User Manual Page 6 Document Revision A CHAPTER 1 PRODUCT OVERVIEW General Information The Plasmon UDO6O0 is a RoHS compliant optical disk drive that reads and writes to 5 25 inch 60GByte UDO Ultra Density Optical media UDO blue laser technology provides a high performance reliable and cost effective long term data storage device The drive handles true Write Once Rewritable and Compliant Write Once media types To insure continued access to data stored on first generation media this second generation UDO60 drive can read first generation 30GByte UDO media but cannot write to it The UDO6O0 is available either as a desktop unit in its own enclosure UDO60D or for internal installation within a system enclosure UDO6OI Each of these models is available with either SCSI or USB connectivity Features The main features of the UDO60D I are 60GByte
4. 1 1 Rapid Flashing NA Loading 0 2 sec cycle spin up On Off 1 1 Slow Flashing Amber Green irregular alternating Drive is in Fail Safe mode Power on diagnostic error Slow Flashing 1 2 sec On 1 2 sec Off Both LEDs On for 1 2 sec and then Off for 1 2 sec Indicates drive failed write power calibration WPC and should be cleaned using the Plasmon lens cleaning cartridge Off Disk not inserted After spin down Power off Drive Not Ready UDO60I Media Insertion and Removal Pressing the eject button opens the drive door to allow insertion or removal of media If the media cartridge is ejected but not removed the drive pulls the media back in after 30 seconds without spinning up Press the eject button again to re eject the media UDO60I Emergency Eject If normal media eject procedures fail to work and it becomes necessary to use the emergency eject mechanism the unit must be powered off Make sure the disk has stopped rotating 20 30 seconds after power off To manually eject the cartridge insert a 2mm flat blade screwdriver into the hole to the left of the normal eject button Rotate the screwdriver clockwise while pressing it firmly into the drive to engage the eject screw mechanism About 60 turns ejects the cartridge Plasmon UDO60D I Drive User Manual Document Revision A Product Overview Page 13 UDO Media The Plasmon UDO60 optical drive reads and writes to Plasmon 5 25 inch two sided
5. 2 z 2 Jumper z 3 Jumper Jumper 4 5 Jumper E s 5 Jumper Jumper 6 Jumper Jumper 7 Jumper Jumper Jumper 8 Jumper 9 Jumper Jumper 10 Jumper lt Jumper E 11 Jumper Jumper Jumper 12 Jumper Jumper 13 Jumper Jumper Jumper 14 Jumper Jumper Jumper 15 Jumper Jumper Jumper Jumper Getting Started Plasmon UDO60D I Drive User Manual Page 22 Document Revision A 2 Mount the drive in the enclosure Attaching screws are supplied with the drive The screws are M3 x 4mm The mounting plate in the enclosure should be within 1 5mm to 2mm thick including the washer CAUTION Mounting plates differ in thickness To avoid damage to the drive only use screws that extend into the drive 1mm to 2mm maximum The UDO6OI can be used in both the vertical and horizontal plane If the vertical position is used the drive should be on its left side with the power connector on top as shown in the figure below In the horizontal position the drive must be top side up Power Connector AN El nloooo m Figure 11 Proper Vertical Orientation for UDO60 3 Connect the drive to the SCSI bus using the supplied 68 conductor flat cable This cable has three keyed connectors and an attached SCSI terminator For correct orientation pin 1 is usually identified by some marking
6. 00 LVD SCSI Cable for UDO60D 910 100775 00 LVD SCSI Cable w terminator for UDO60I 910 102466 00 USB 2 0 A to B Cable for UDO60D 910 102767 00 USB 2 0 mini B to 5 pin Cable for UDO6OI 910 100736 00 UDO6OD Fan Filters Product Overview Plasmon UDO60D I Drive User Manual Page 16 Document Revision A CHAPTER 2 GETTING STARTED Unpacking When moving the UDO60 to an environment where there is a significant difference in temperature or humidity leave the unit in its packaging for at least two hours Find a clean flat soft surface for unpacking For the UDO6OI full anti static precautions should be followed while handling Use an anti static mat and ground when handling the internal unit Always hold the internal unit by the frame only and do not touch any electrical components Refer to the enclosed packing list to verify the accessories supplied with the UDOGO drive Setting Up the UDO60D For USB Connection If the drive is connecting to a USB interface follow these steps 1 The UDO6OD should only be used in the horizontal plane 2 Connect the in line power supply and power cord to the unit and connect the power cord to an appropriate grounded power source 3 With the drive and the host computer both powered on connect the USB cable between the UDO60D and the host computer 4 Insert the UDO Resource CD wait for it to auto start and install the UDO software If the system does not supp
7. UDO media cartridges with 60GByte capacity and reads first generation 30GByte media These are available in true Write Once Rewritable and Compliant Write Once media types Compliant Write Once media provides for selective data destruction for security purposes Figure 7 UDO Media Types UDO media is the same form factor as MO media However UDO media is not compatible with MO drives and MO media is not compatible with UDO drives UDO media is two sided To access side A for example insert the media with the side marked A facing up toward top of drive New UDO media must be formatted before use Refer to the software documentation on the supplied UDO Drive Resource CD Write Protecting Media To write protect one side of the media slide the write protect tab on that side in the direction of the protect arrow as shown in the figure below There is a write protect tab on each side of the disk When a side is protected the write protect window is open Write Protect Tab mi va Figure 8 Write Protecting UDO Media Product Overview Plasmon UDO60D I Drive User Manual Page 14 Document Revision A Media Care and Handling CAUTION Always condition the media to room temperature before loading it into the UDO60 drive Media cleaning should only be performed by Plasmon trained personnel Improper handling or an inappropriate environment can damage the media To ensure continued reliability When media is loaded into
8. 30GB per side storage on rewritable and write once media Half height 5 25 inch form factor 32MByte data cache for write and read operations 28ms typical seek time Up to 80MBytes sec synchronous data rates Wide Ultra2 LVD SCSI or 6 OMBytes sec USB 2 0 Universal AC supply operates from 100 to 240 volts desktop version RoHS compliant Plasmon UDO60D I Drive User Manual Product Overview Document Revision A Page 7 About the UDO60D The UDO6OD is the desktop version of the drive This drive ships in its own enclosure which provides the appropriate connectivity Plasmon offers either a USB or a SCSI connectivity option USB Connectivity Power Power On LED Fan and Air Filter Connector USB Connector Power Switch Figure 1 UDO60D u Back View The USB connector is a USB 2 0 Type B connector SCSI Connectivity Power Power On LED SCSI ID Switches Fan and Air Filter Connector AN Power Switch SCSI Connectors Figure 2 UDO60D s Back View The two SCSI connectors are SCSI 3 standard shrouded keyed 68 pin Micro D connectors The SCSI ID switches are used to set the SCSI ID for the drive Setting the SCSI ID is covered in the next chapter under Setting Up the UDO6OD Product Overview Plasmon UDO60D I Drive User Manual Page 8 Document Revision A LED Functions LED Active Amber Plasmon Emergency Eject Figure 3 UDO60D Front View LED Ready Green Eject Button On the front of the drive there
9. CIFICATIONS Drive Specifications These specifications are subject to change without notice Table 9 UDO60 Drive Specifications Rotational Speed WORM RW Specification UDO60D UDOG6OI Access Times Average Seek 1 3 full stroke 28 ms 28 ms Load Time 5 sec 5 sec Unload Time 3 sec 3 sec 2100 1950 RPM 2100 1950 RPM Data Transfer Rates Number of Media Insertions Max Sustained Read 12 MB s 12 MB s Max Sustained Write 8 Verify 6 MB s 6 MB s Burst Synchronous Fast SCSI 80 MB s 80 MB s enabled Burst Synchronous USB 2 0 60 MB s 60 MB s Buffer Size 32 MB 32 MB MTBF Power On Hours 100 000 hrs 100 000 hrs 750 000 cycles 750 000 cycles Environmental Operating Temperature Non operating Temperature Operating Humidity Non operating Humidity 5 to 35 C 40 to 60 C 5 to 90 non condensing 5 to 95 non condensing 5 to 45 C 40 to 60 C 5 to 90 non condensing 5 to 95 non condensing Electrical Operating Voltage Power Requirements 100 to 240VAC 50 60Hz 12V 4 2A Max 50W 5V E 5 12V 45 5V 2 5A Max 1 9A Typ 12V 2 8A Max 0 6A Typ Structure Dimensions WxHxD in mm Weight Drive Orientation 185 x 65 x 283 2 9 Kg w o power cord amp supply Horizontal 146 x 41 1 x 207 8 1 5 Kg Horizontal Vertical Drive Warranty Plasmon UDO60D Drive User Manual Document Revision A One year parts amp labor return to base One y
10. ERELERE 1 COPY axa cee bee eee on Peek Eas eee ESPE le dE bee bese ee 1 DISCIAIM EG vascos cc Aiwa tad Gaul dea eee dd ceed dak ed deed Iw es 1 Trademark Notices y c2xiecccchtasdiee es a seee eo 1 Revision HIStOTY errors a aba 1 Conventions USSO coria rs ee eed rad bbe d koe eae hes 2 WEEE Compliance cr res ge MED EERE A eee chee dees awe es 2 PIOGUC WIANIAINY ee esseeri taa residence cs tanta beatese seas dd 3 CHAPTER 1 FPRODUCT OVERVIEW rr ARA 7 General Information sic dhe eae ee SOs Pee A ess cerda n 7 ESAS cuna A we Baada soe ae ea ik eA Ae datada aa 7 ADOT the UDO6B0D suai ki wo wie aaa A el meee 8 USB Connectivity cs iaia saa a a he det eg ae 8 SCSI CONMSCHVITY e aa ag Sas aes cota aida eS ae De ae PD ae ee e da A a 8 LED FUNCHONS aia wea A A eid le eee ea ald eee ead A a 9 UDOG6O0D Media Insertion and Removal 0 0 00 tee teens 10 UDO60D Emergency Eject 0 0 0 10 UDOGOD Air FIRES eperera a a di Sawa ae tc aed a 10 In Line Power Supply 0 000 teeta 10 About the UDOSOl isc finadiee todd setae de peated rad 11 USB ComecliVitY von ir dy a de an Pe a ee ie a 11 SCSI Connectivity coca cis a a de a bes a ee Bhs a 11 Power ComnectiVit Y a da we daiwa E E Mt 12 Function Connectivity eassa saaana teen eae 12 LED FUNCIONS sp a a eed ww A eee a a ee he 12 UDO6OI Media Insertion and Removal nananana anaana 13 UDO60I Emergency Eject 0 00 tte eee 13 UDO M dia se ct ica hd eh
11. ae AR RRS aac ae are 14 Write Protecting Media 0 ccc teens 14 Media Care and Handling 0 00 ccc ete 15 Software Drivers uta css tee pare a ae babes somes E een eeae aun ead 15 Accessories and Spares 0 0000 ccc ete 16 Plasmon UDO60D I Drive User Manual Table of Contents Document Revision A Page 5 CHAPTER 2 GETING OIART asia a a a ar ra AAA ERA 17 UNPACKING 0 2264 22005 S oe ESE ENEE EEE BEE EER Oe 17 setting Up the UDOGOD evo iocsee deees bee e Paes dS ee eee eRN Ge Seaweed 17 For USB Connection Vida ion Gd a ha de ea Ree wah wa eS a Ga da A 17 For SCSI Connection 00 eee eee eee eens 17 setting TIN Enable cio esi beads Sida hee ee ce Pele ee ida 19 Setting Up the UDOGO cise ne Stk eRe Sh ay RAMs okay EES oF PEK bore da bees 20 For USB Connectivity 0 2 0 0 6c ete 20 For SCSI Connectivity 0 00 0 tetas 21 Setting TIN Enable seri oa aia iehi aa a aaa e aa a a a i a a E i e EAA N na 24 APPENDIX A SPECIFICATIONS oast ee eK Eo a FERRE ER SEES REED 25 Drive Specifications ot tinct dan ra da ea earn ne 25 SCSI Cable Specifications 0 00 tee 26 SCSI Cables and Connectors 0 0 0 eee eee ee nee eae 26 SCSI Termination 10000 ie dod wate a hk iA A aoe OR Aas Wa ee ee a 26 USB Cable SpociliG lOs cssi nsiodaniecirdsciin prestada 26 APPENDIX B SAFETY AGENCY STANDARDS c0ccococcoccc a 27 FEC NOCO se a a eke os o Ss 27 Industry Canada Notice per ICES 008B
12. are two LEDs which function as explained in the following table Table 1 UDO60D LED Signals variable cycle alternating LEDs Power on diagnostic error LED Pattern Active Amber Ready Green On Accessing disk Media Ready Power on diagnostic Power on diagnostic Flashing NA Inaccessible disk inserted 0 8 sec cycle Drive Not Ready On Off 1 1 Rapid Flashing NA Loading 0 2 sec cycle spin up On Off 1 1 Slow Flashing Amber Green irregular alternating Drive is in Fail Safe mode Slow Flashing 1 2 sec On 1 2 sec Off Both LEDs On for 1 2 sec and then Off for 1 2 sec Indicates drive failed write power calibration WPC and should be cleaned using the Plasmon lens cleaning cartridge Off Disk not inserted After spin down Power off Drive Not Ready Plasmon UDO60D I Drive User Manual Document Revision A Product Overview Page 9 UDO60D Media Insertion and Removal Pressing the eject button opens the drive door to allow insertion or removal of media If the media cartridge is ejected but not removed the drive pulls the media back in after 30 seconds without spinning up Press the eject button again to re eject the media UDO60D Emergency Eject If normal media eject procedures fail to work and it becomes necessary to use the emergency eject mechanism the unit must be powered off Make sure the disk has stopped rotating 20 30 seco
13. e drive in the enclosure Attaching screws are supplied with the drive The screws are M3 x 4mm The mounting plate in the enclosure should be within 1 5mm to 2mm thick including the washer CAUTION Mounting plates differ in thickness To avoid damage to the drive only use screws that extend into the drive 1mm to 2mm maximum The UDO6OI can be used in both the vertical and horizontal plane If the vertical position is used the drive should be on its left side with the power connector on top as shown in the figure below In the horizontal position the drive must be top side up Power Connector E A i foeoo im Figure 9 Proper Vertical Orientation for UDO6OI Getting Started Plasmon UDO60D I Drive User Manual Page 20 Document Revision A 2 Connect the drive to the enclosure s USB 2 0 connector using the supplied mini B to 5 pin cable 3 Attach the enclosure s power connector to the drive The connector is keyed to ensure proper orientation 4 Insert the UDO Resource CD wait for it to auto start and install the UDO software CAUTION Do not insert media into the drive until the software installation is complete For SCSI Connectivity If the drive is connecting to a SCSI interface before applying power follow these steps 1 For convenience set the SCSI ID for the drive be
14. ear parts amp labor return to base Specifications Page 25 SCSI Cable Specifications SCSI Cables and Connectors Plasmon recommends using LVD SCSI cables and connectors that conform to SCSI 3 specifications The SCSI version of the Plasmon UDO6OD is shipped with a shielded two meter LVD SCSI cable with shielded 68 pin Micro D connectors The UDO6OI is shipped with an LVD flat SCSI cable with three keyed 68 pin connectors and a terminator attached SCSI Termination The SCSI version of the Plasmon UDO6OD is shipped with an LVD HD68 SCSI terminator The UDO6OI is shipped with a terminator attached to the flat cable If the drive is the last device on a SCSI bus termination is required USB Cable Specification The USB version of the Plasmon UDO6OD is shipped with a USB 2 0 A to B cable The USB version of the UDO6OI is shipped with a USB 2 0 mini B to 5 pin cable Specifications Plasmon UDO60D I Drive User Manual Page 26 Document Revision A APPENDIX B SAFETY AGENCY STANDARDS FCC Notice The equipment to which this manual pertains has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with this User s Gu
15. eevevusou yg Ground Tab Figure 5 UDO60I s Back View The SCSI connector is a SCSI 3 standard keyed 68 pin connector A flat SCSI cable with 68 pin connectors is supplied with this drive Plasmon UDO60D I Drive User Manual Product Overview Document Revision A Page 11 Power Connectivity The UDO60 DC power connector is an industry standard keyed 4 pin connector Table 2 UDO60 Power Connector Pin Description 1 12V DC 2 8A Peak 100ms Max 0 6A Typ 2 12V DC Return 3 5V DC Return 4 5V DC 2 5A Max 1 9A Typ Function Connectivity The Function connector is used by Plasmon when the drive needs to communicate within a data library Here the first four pairs of pins are used with supplied jumpers to set the SCSI ID for the drive Setting the SCSI ID is covered in the next chapter under Setting Up the UDO6OI LED Functions LED Active Amber LED Ready Green E Emergency Eject Eject Button Figure 6 UDO60I Front View On the front of the drive there are two LEDs They function as explained in the following table Product Overview Plasmon UDO60D I Drive User Manual Page 12 Document Revision A Table 3 UDO60I LED Signals variable cycle alternating LEDs LED Pattern Active Amber Ready Green On Accessing disk Media Ready Power on diagnostic Power on diagnostic Flashing NA Inaccessible disk inserted 0 8 sec cycle Drive Not Ready On Off
16. f the power cord set shall be higher than the power source For the U S and Canada Power cord must be UL listed and CSA labeled Type SJT SVT ST SJO or SO 3 conductors No 18 AWG rated 125V 10A Safety Agency Standards Plasmon UDO60D I User Manual Page 30 Document Revision A CONTACTING PLASMON Technical Support in the United States Plasmon Technical Support 1 877 585 6793 1 719 593 4192 fax e mail tech support plasmon com Internet www plasmon com Technical Support in Europe Middle East and Africa Plasmon Technical Support 44 0 1763 262 963 44 0 1763 264 444 fax e mail support plasmon co uk Internet www plasmon com Technical Support in Asia Pacific South America and Canada International Calls 1 719 593 4437 1 719 593 4192 fax e mail tech support plasmon com Software and Driver Updates Contact your service provider for the latest firmware and driver updates Before Placing a Service Call to Plasmon Register your site on line at http www plasmontech com warranty index html Placing a Service Call Contact your service provider directly If Plasmon is your service provider please have the following information available when calling Serial number Description of failure System information Computer type and SCSI adapter Software configuration Software and version number Plasmon The Leader in Profes
17. fore installing it in an enclosure Each device on a SCSI bus requires a unique ID in the range of 0 to 15 for Wide SCSI ID 7 is usually reserved for the host computer The UDO6O0I is shipped with SCSI ID 1 0001 set as a default The SCSI ID is set on the UDOG6OI by placing appropriate jumpers on the first four pairs of pins of the Function Connector located on the back of the drive There is a label on the top of the drive which shows which pin pairs of the Function Connector are used to set the SCSI ID bits The following figure also shows this information SCSI ID bits TIN Termination 3210 Enable Power Pin 1 i X Figure 10 UDO60I Function Connector Jumper Options Key way Termination power is set at the factory as the default by placing a jumper across the last pin pair pins 23 amp 24 The following table shows how the pin pairs relate to the SCSI ID bits Plasmon UDO60D I Drive User Manual Getting Started Document Revision A Page 21 Table 7 UDO60 I SCSI ID Pin Pairs Pins SCSI ID Bits binary 182 SCSI ID Bit 3 MSB 3 amp 4 SCSI ID Bit 2 586 SCSI ID Bit 1 788 SCSI ID Bit O LSB 9810 TIN Enable Refer to the following table for setting the drive SCSI ID Table 8 Setting UDO60 SCSI IDs SCSI ID Pins 1 8 2 Pins 3 amp 4 Pins 5 8 6 Pins 7 8 8 0 5 1 Jumper
18. ide may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and the receiver Connect the equipment into a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help Industry Canada Notice per ICES 003 English This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus set out in the interference causing equipment standard entitled Digital Apparatus ICES 003 of the Industry Canada French Cet appareil num rique respecte les limites de bruits radio lectriques applicables aux appareils num riques de Classe B prescrites dans la norme sur le mat riel brouilleur Appareils Num riques NMB 003 dict e par l Industrie Canada European Notice C This product is in conformity with the following directive EN 55022 CISPR 22 Class B EN 55024 EN 61000 3 2 EN 61000 3 3 This product is in conformity with the EMC directive and low voltage directive Plasmon UDO60D User Manual Safet
19. ine WARNUNG ist benutzt den Leser zu Lagen oder Bedingungen zu warnen die m glicherweise in pers nlicher Verletzung Brandrisiko oder Geratschaden resultieren k nnten CAUTION A CAUTION is used to warn of undesirable procedures or of situations in which equipment damage could result NOTE A NOTE is used to emphasize an area of text or to provide additional information WEEE Compliance Plasmon products with the Waste Electrical and Electronic Equipment Directive WEEE label shown below can be shipped back to Plasmon for proper disposal of hazardous components Please contact Plasmon Technical Support at the locations listed inside the back cover of this manual for the proper procedure Preface Plasmon UDO60D I Drive User Manual Page 2 Document Revision A Product Warranty Plasmon warrants hardware products against defects in materials and workmanship and that the hardware conforms to Plasmon specifications for one year from date of purchase from Plasmon depending on product type This warranty provides for a no cost repair or replacement of defective hardware upon return of hardware to a Plasmon Repair Depot The decision to repair or replace is solely at the discretion of Plasmon Plasmon reserves the right to use remanufactured parts or products that are equivalent to new in performance as replacements Site registration for warranty may be completed at http www plasmontech com warranty index html The Plasmon warra
20. nds after power off To manually eject the cartridge insert a 2mm flat blade screwdriver into the hole to the left of the normal eject button Rotate the screwdriver clockwise while pressing it firmly into the drive to engage the eject screw mechanism About 60 turns ejects the cartridge UDOG6OD Air Filters The UDO6OD is shipped with an air filter installed in the back of the casing This air filter is required When the filter is noticeably dirty it must be replaced Additional filters are supplied with the drive In Line Power Supply The UDO6OD is shipped with an in line power supply and power cord Do not replace the supply with a substitute An authorized replacement is available from Plasmon Please refer to the Accessories and Spare Parts section at the end of this chapter Product Overview Plasmon UDO60D I Drive User Manual Page 10 Document Revision A About the UDOG6OI The UDO6OI is intended for installing in a system enclosure It fits standard 5 25 inch device mounting spaces and provides the appropriate connectivity Plasmon offers either a USB or a SCSI connectivity option USB Connectivity Function Connector USB Connector Power Connector ee O A 00088 Ground Tab Figure 4 UDO6OI u Back View The USB connector is a USB 2 0 Type B connector A USB 2 0 mini B to 5 pin cable is supplied with this drive SCSI Connectivity Function Connector SCSI Connector Power Connector E weweveweweeve
21. nty is automatically activated 30 days from the date of shipment from the factory unless Plasmon is notified that an earlier commencement is requested Additional coverage may also be purchased Please contact your local Plasmon support representative for more information and service contract details Spare parts are covered by a 180 day warranty Remanufactured parts are covered by a 90 day warranty Warranties for either spare parts or remanufactured parts are from the date of shipment unless the original warranty of the unit is still in force and the remainder of the original warranty exceeds the stated warranty periods above CAUTION Returning the drive in unauthorized packaging may damage the unit and void the warranty If problems with the drive occur contact your maintenance organization do not void the product warranty by allowing untrained or unauthorized personnel to attempt repairs WARNING Untrained personnel operating the drive may create dangerous situations This could lead to physical harm to the operator data loss and or disabling of the drive WARNUNG Ungeschultes Personal das den Antrieb bedient kann gefahrliche Lagen bedingen Dies k nnte zu physischem Schaden des Bedieners Datenverlust oder Antrieb Sperre f hren Plasmon UDO60D I Drive User Manual Preface Document Revision A Page 3 Preface Plasmon UDO60D I Drive User Manual Page 4 Document Revision A TABLE OF CONTENTS PREFACE AA GAH EE EEK OAT
22. ocedures other than those specified herein may result in hazardous radiation exposure WARNUNG Gebrauch von Steuerungen oder Regelungen oder Leistung der Verfahren anders als die angegebene hierin kann in gef hrlicher Bestrahlungsaussetzung resultieren CLASS 1 LASER PRODUCT LASER KLASSE 1 PRODUKT Laser Technical Data Type GaN diode laser Wavelength 408 nm 5 nm Maximum power 45 mW CW 60 mW pulsed CAUTION e gt i 5 CLASS 3B LASER LIGHT WHEN OPEN Class 1 product label located on the drive s outer enclosure AVIOD EXPOSURE TO THE BEAM Class 3B laser caution label located on drive s internal chassis wO RSICHT KLASSE 3B LASER LEICHT VSB OFFEN NICHT IN DEN STRAHL BLICKEN Complies with IEC 60825 1 1993 A1 1997 A2 2001 Plasmon UDO60D User Manual Safety Agency Standards Document Revision A Page 29 CDRH Regulations The Center for Devices and Radiological Health CDRH of the U S Food and Drug Administration implemented regulations for laser products on August 2 1976 These regulations apply to laser products manufactured from August 1 1976 Compliance is mandatory for products marketed in the United States Use of controls adjustments or performance of procedures other than those specified in this manual may result in hazardous radiation exposure Power Cord Set Selection The voltage rating and the current rating of the power cord set shall be higher than the rated voltage and current of this unit The voltage o
23. or color on the edge of the cable and by a small arrow on the connectors 4 Attach the enclosure s power connector to the drive The connector is keyed to ensure proper orientation Plasmon UDO60D I Drive User Manual Getting Started Document Revision A Page 23 5 Insert the UDO Resource CD wait for it to auto start and install the UDO software CAUTION Do not insert media into the drive until the software installation is complete Setting TIN Enable Along with the SCSI ID pins on the Function Connector on the back of the UDOG6OI is a pair of pins 9 and 10 which are jumpered to set TIN Enable Turning on TIN Target Initiated Negotiations enables the drive to negotiate Wide and Synchronous on the SCSI bus The default setting for TIN Enable is off not jumpered since target devices do not normally initiate negotiation Some platforms drivers or adapter cards may fail to re negotiate correctly under certain conditions In this event the host computer cannot communicate with the drive over the SCSI bus Enabling TIN allows the drive to re negotiate and maintain communication with the host If communication is lost on power cycles or drive resets at host boots setting the TIN Enable switch may solve the problem In general Microsoft systems may need TIN enabled AIX Unix and Linux systems typically need TIN disabled Getting Started Plasmon UDO60D I Drive User Manual Page 24 Document Revision A APPENDIX A SPE
24. ort auto start open the CD and double click on the autorun exe file CAUTION Do not insert media into the drive until the software installation is complete For SCSI Connection If the drive is connecting to a SCSI interface before applying power follow these steps 1 Set the SCSI ID of the drive via switches on the back of the unit Refer to the section About the UDO6OD in the previous chapter to locate the SCSI ID switches Plasmon UDO60D I Drive User Manual Getting Started Document Revision A Page 17 Each device on a SCSI bus requires a unique ID in the range of 0 to 15 for Wide SCSI ID 7 is usually reserved for the host computer The UDO6OD is shipped with SCSI ID 1 0001 set as a default There is a label next to the switches showing how to set IDs This information is also shown in the following table Table 5 UDO60D SCSI ID Switches Switch SCSI ID Bits binary 1 SCSI ID Bit 3 MSB 2 SCSI ID Bit 2 3 SCSI ID Bit 1 4 SCSI ID Bit O LSB 5 TIN Enable 6 No Connection Refer to the following table for switch settings Table 6 Setting UDO60D SCSI IDs SCSI ID Switch 1 Switch 2 Switch 3 Switch 4 0 7 E E 1 z On 2 On 3 4 On On 4 On g z 5 On On 6 E On On 7 On On On 8 On 9 On gt 5 On 10 On z On 11 On 3 On On 12 On On a 2 13 On On gt On 14 On On On 15 On On On On Getting Started Pla
25. sional Data Archival Solutions
26. smon UDO60D I Drive User Manual Page 18 Document Revision A The host computer must have a SCSI host adapter card such as the Adaptec 29160 equipped with a 68 pin Micro D connector 2 Connect the supplied 68 conductor LVD SCSI cable between the computer and the drive The UDO6OD is equipped with two Micro D 68 pin connectors on the rear panel A SCSI bus must be terminated at each end of the line One terminator is required on the last device in the chain The other terminator is usually on the host computer or adapter card Refer to the documentation supplied with your SCSI card or computer system to check the host termination This is normally enabled 3 If the drive is the last device on the SCSI bus install the supplied terminator in the drive s unused SCSI connector 4 The UDO6OD should only be used in the horizontal plane 5 Connect the in line power supply and power cord to the unit and connect the power cord to an appropriate grounded power source 6 Apply power to the unit before applying power to the host computer 7 Insert the UDO Resource CD wait for it to auto start and install the UDO software If the system does not support auto start open the CD and double click on the autorun exe file CAUTION Do not insert media into the drive until the software installation is complete The UDO6O also operates in single ended SCSI mode depending on the other devices connected to the SCSI bus Setting TIN Enable
27. the drive or when handling media ensure that the cartridge case is clean Dirty media cartridges may cause problems If a cartridge case is dirty wipe with a lint free cloth Do not carry media loosely for example in a box or basket Do not load damaged media into a drive Damaged media can interfere with reliability Never touch the disk Opening the cartridge door and touching the disk may interfere with read write reliability Do not expose the media to moisture or direct sunlight Software Drivers The UDOG6O optical drives are supplied with software for the Windows and Linux operating systems When the UDO60 drive setup is complete insert the provided UDO Drive Resource CD and follow the instructions to install the appropriate software CAUTION Do not insert a media cartridge into the drive until the software installation is complete Plasmon UDO60D I Drive User Manual Product Overview Document Revision A Page 15 Accessories and Spares Table 4 Accessories and Spares List Part Number Description Media UDO60RWX5 Plasmon 60GB UDO Rewritable 8 192 Bytes sector 50 year data life sold in packs of five UDO60WOX5 Plasmon 60GB UDO true Write Once 8 192 Bytes sector 50 year data life sold in packs of five UDO60CWX5 Plasmon 60GB UDO Compliant Write Once 8 192 Bytes sector 50 year data life sold in packs of five Spares 910 100713 00 UDO6OD in line power supply 910 100835
28. y Agency Standards Document Revision A Page 27 Australia New Zealand This equipment has been tested and complies with AS NZS 3548 Japan CORE FRUELESTEREE BEER VCCI ORB HOC VFABMRRMRECST CORE KERR CEAT OTE ZEEL TOETH CORBPIVAPTLEY aY HERTEL T ASNA E SMS E TCEPHVET PRBS HE TELUBMIV RUI 4LTF AL This is a Class B product based on the standard of the Voluntary Control Council for Interference from Information Technology Equipment VCCI If this is used near a radio or television receiver in a domestic environment it may cause radio interference Install and use the equipment according to the instruction manual Product Safety Standards The Plasmon UDO60D I drives comply with the following domestic and international product safety standards UDOG6OI UL Standard 60950 1 1st Edition 2003 Safety of Information Technology Equipment CSA Standard C22 2 No 60950 1 03 Safety of Information Technology Equipment IEC 60950 1 1st Edition 2001 UDO60D UL Standard 60950 3rd Edition Safety of Information Technology Equipment CSA Standard C22 22 No 60950 00 3rd Edition Safety of Information Technology Equipment IEC 60950 3rd Edition 1999 Safety Agency Standards Plasmon UDO60D I User Manual Page 28 Document Revision A Laser Safety Notice This drive complies with 21 CFR 1010 10 1040 11 and IEC 60825 1 1993 A1 1997 A2 2001 as a Class 1 Laser product WARNING Use of controls or adjustments or performance of pr
Download Pdf Manuals
Related Search