User Manual - Sensortronic Scales
Contents
1. KEY FUNCTIONS ZERO Used to set the zero point to 0 00 or 0 000 Used as ENTER key in Setup Mode TARE Used to enter a tare weight and used to cancel a tare weight Used as ESC key in Setup Mode kg lb Used to switch between Ib and kg 1 General Weighing m The display indicates if the scale is at zero or if there is a tare entered into the scale by way ofa ZERO and NET m When the display is not zero though there is nothing on the platter press the ZERO key Tum on the power The display shows 0 00 or 0 000 Make sure that ST Stable and ZERO lamps are On Place an item on the platter When the ST Stable lamp is On read the weight 2 Weighing with Tare m There is the weight of container being used for a commodity m The TARE key subtracts the weight of the container O Place the container on the platter Q Press the TARE key NET lamp is On Place an item in the container To release the TARE function remove an item and container from the platter and press the TARE key 3 ECR Interface m PD II can interface with most ECRs by selecting TYPE 0 to TYPE 6 ECR Type Selection Make sure that power is OFF While pressing TARE key tum on the power EcrSEt is shown on the disply And then current ECR type is shown on the display as tYPE 2 Q If you select ECR type 5 press the TARE key until the display shows tYPE 5 Refer to Table 1 To save curr2. Communication ECR Interface POWER SUPPLY AC 120V 60Hz MEMO CI eee e e MEMO MEMO 14 CI eee e e ee Cr ee CAS Ss C A L E 9002 PD2 0011 0 2007 02
3. Owner s Manual ECR Interface Scale CONTENTS PRECAUTIONS soa sn 4 PREFACE ich 6 NAMES AND FUNCTIONS 6 OPERATIONS asas naus 8 1 General Weighing suse 9 2 ECR Interface eerercenencesenseconensenensecensasenense censos 9 ERROR MESSAGE cc ccssssssssessccsescsnseesenee 10 SPECIFICATIONS mscssinscoseerassoceerssssseserstonsessasoss 11 PREFACE N Warning To ensure that you get the most from your scale please follow these instruction Do not disassemble the Do not overload beyond the E Scale must be grounded to scale maximum weight limit minimize electricity static When any damage or defect This will minimize occurs contact your CAS defect or electric shock authorized dealer immediately for proper repair Do not pull the plug by its JJ To prevent from fire To reduce electric shock or cord when unplugging occurring Do not place or incorrect reading Do not use the scale near spill water on the scale or flammable or corrosive gas 8 place it in humid condition Damaged cord could cause electric shock or fire A Attention The socket outlet shall be installed near the equipment and shall be easily accessible Make sure to plug your scale into the proper power outlet For maximum performance plug into a power outlet 30 minutes before the usage for warm up Avoid sudden shock to Grab on the bottom of the scale the scale when movin
4. ent ECR type press the ZERO key Table 1 Description MENU 4 Bit Parallel RS 232 Serial ECR TYPEO TEC 4 ni a Parallel New kg Most POS ECRs and Some TEC 4 Digit 4Bit Parallel TEC POS System ECR TYPE 1 Old kg Sharp ER Axxx New Sanyo kg lb key ECR TYPE 2 ECRs using RS 232 others l ECR TYPE 3 Most POS System Samsung CRS NCR2170 and ECR TYPE 4 Universal 4 Bit Parallel other ECRs NCI General BURN PES Most POS Software ECR TYPE 6 Samsung ER 670 X Serial Communication gt 9600 Baud Rate 7 Date bit Even Parity 1 Stop bit ERROR REASONS SOLUTIONS Err Failure of A D Module Call your CAS dealer ss Set the platter empty Emi An Gror emita orange Make sure there is a platter on the scale SPECIFICATIONS 11 MODEL 15 Ib 6kg 30 Ib 15kg 60 Ib 30kg 150 Ib 60kg 5lbx0 002lb 15lbx0 005 lb 30lbx0 01lb 60 lb x 0 02 lb 15 lb x 0 005 Ib 30 Ib x 0 01 lb 60lbx0 02lb 150 lb x 0 05 lo DIVISION DUAL INTERVAL 3kg x 1g 6kg x 2g 15kg x 5g 30kg x 10g 6kg x 2g 15kg x 5g 30kg x 10g 60kg x 20g INTERNAL RESOLUTION 1 90 000 EXTERNAL RESOLUTION 1 3 000 DUAL DISPLAY VFD 6 DIGITS DISPLAY LAMP ST STABLE ZERO NET kg lo INTERFACE 380 W x 280 D mm PRODUCT SIZE 380 W x 280 D x 79 H mm PLATTER SIZE 6 7kg PRODUCT WEIGHT 0T 40T TEMPERATURE RANGE RS 232C 4 Bit Parallel
5. g For consistent and accurate reading maintain periodical check by your CAS authorized dealer Keep the scale away from BM Place the scale on firm By adjusting 4 comers of other electromagnetic and temperature the scale set the scale enerating devices consistent environment even using the built in scale leveling indicator This may interfere with accurate reading PREFACE Thank you for purchasing our CAS PD II These series have been designed with CAS reliability under rigid quality control and with outstanding performance Your specialty departments can enjoy these high quality reliable CAS products We believe that your needs will be satisfied and you will have proper reliability This manual will help you with proper operation and care of the PD IL Please keep it handy for future reference NAMES AND FUNCTIONS OVERALL VIEW PLATTER DISPLAY KEYBOARD ADJUSTING BOLT lt STANDARD TYPE gt POWERSWITCH paRALLELPORT RS232 POLE TYPE DISPLAY E PLATTER POLE TYPE RA DISPLAY CABLE A Z KEYBOARD ADJUSTING BOLT lt POLE TYPE gt DISPLAY ID CAPACITY 0 6 Ib x 0 002 Ib 6 15 Ib x 0 005 Ib 0 3 kg x 0 001kg 3 6 kg x 0 002 kg CAS MODEL PD II ZERO ST NET kg lb ZERO TARE org CAS MODEL PD Il ST ZERO NET UD CAPACITY 0 6 Ib x 0 002 Ib 6 15 Ib x 0 005 Ib 0 3 kg x 0 001kg 3 6 kg x 0 002 kg m KEY FUNCTIONS
Download Pdf Manuals
Related Search