instructions manual
Contents
1. See the section To clean the grid Warning of leakage condensation inside the base under the filter containers Check that all connections are watertight If there is water inside the base wipe it dry tilt appliance forward if necessary The intake water pressure is too low i e less than 1 5 bar 150 kPa Warning that filter needs replacing Warning of reduced water quality Warning that the tap has been on for more than 20 minutes without a pause and that the appliance has shut down automatically as a result Warning that calibration has been started but not completed correctly probably because the tap has been turned off before the full 10 minutes Warning of error in water quality meter A booster pump to increase the pressure to the water purifier can solve this problem Check all the factors which can affect water pressure water supply grid special filters Replace filter See Replacing the filters If the appliance is new and has never been calibrated calibrate the appliance see Calibration Restart the water purifier by disconnecting then recon necting the electricity so that the appliance switches to flushing mode Repeat this procedure two or more times T urn off the tap and leave the water purifier undis turbed for at least 30 minutes Restart the appliance by disconnecting and then recon necting the electricity After automatic flushing the water purifier2. kept and stay with the water purifier if it is ever moved or changes owners so that everyone who uses the appliance can read about the various functions and safety instructions The manual s English instructions begin on page 5 VIELEN DANK dass Sie unseren Wasseraufbereiter gew hlt haben Wir hoffen dass Sie viele Jahre Freude an dem haben werden Um Probleme zu vermeiden ist es wichtig diese Gebrauchsanweisung aufmerksam zu lesen und die Anweisungen und Informationen der Sicherheitshinweise und der nstallationsanleitung zu beachten Alle die den Wasseraufbereiter benutzen sollten mit seiner Bedienung vertraut sein und wissen was in einem Storungsfall zu tun ist Dieses Handbuch ist immer bei dem Wasseraufbereiter aufzubewahren Geben Sie diese Unterlagen im Falle eines Verkaufs an den neuen Besitzer weiter Die deutschen Bedienungsanweisungen dieses H andbuchs beginnen auf Seite 27 MERCI de nous faire confiance en optant pour votre nouveau purificateur d eau qui nous l esp rons vous servira sans d faillance et vous donnera satisfaction pendant de nombreuses ann es Afin d viter tout probl me ne manquez pas de lire la section intitul e S curit ni de vous conformer scrupuleusement aux instructions d installation Q uiconque utilise le purificateur devra en connaitre le maniement et les dispositifs de s curit Conserver avec soin le pr sent manuel d instructions et veiller ce qu il acc
3. nk ping Sweden 20 INSTALLATION You should read the section entitled Safety Information before starting work on the actual installation of the water purifier Unpacking If the appliance has been damaged during transportation you should immediately notify the company responsible A for delivering it T ake hold of the rear hand grip and the front edge of the A water purifier and carefully lift the appliance out The d appliance can be damaged if it is lifted in any other way Z Check the water purifier for any signs of damage and check that no accessories are missing If you do discover any 460 mm 250 mm damage faults or that anything is missing you should ee SE report this to the seller immediately Never leave packag B i ing material in a place where children may play with it Where to install the water purifier 490 mm T his water purifier can be installed in several different _ ways We will describe the most suitable of these No mat Sa e The area where it is installed must have access to a cold water supply a normal domestic waste pipe drain and an earthed electrical supply e It must be easy to inspect the control panel on the appliance e There must be enough space for the front cover to be opened and for good access to the filter containers e When choosing the site make sure there will be ade quate ventilation all around th
4. properly If so start again from step 1 of this Calibration procedure 3 Turn off the tap for drinking water The appli ance will switch to flushing mode then stop automatically The water purifier will now be ready for use Moving the water purifier If you move the water purifier to a different location you must observe the following points e Close the shut off valve on the cold water supply pipe e Disconnect the electrical plug from the socket e Always transport the appliance in its normal upright position To reinstall it follow the original installation instructions e The appliance will only need to be recalibrated if the water supply is of a different quality or if the membrane has been replaced If the appliance is to be stored without being used for longer than 4 months see section Preparing the water purifier for storage 29 26 f li Loun x NOTE Endast i vissa modeller In certain models only Pos 999 har ej visats i bild is not shown in the picture Endast i vissa modeller In certain models only SPARE PART LIST FOR RO 400C PRODUCT NO 919 24 01 17 Position in Description Article no picture RO 400C 230 V INSIDE 1 2 3 3B 4 5 6 6A 6B 6C 7 8 9 10 11 11 12 13 14 15 16 17 18 20 21 22 22B 23 24 25 26 27 28 29 30 31 33 34 35 36 37 38 39 40 41 100 110 111 120 131 132 133 140 150 151 150 73 11 00 7 SPARE PART LIST F
5. the cable for the indicator lights on the tap then move the appliance carefully into its permanent location Connect the electrical plug to the wall socket Fig D The appliance will now start working flushing The appliance carries out this flushing operation every time it is reconnected to the power supply N o water from the appliance should be consumed until you have followed the full Flushing procedure After installing and testing the appliance turn on the appli ance s drinking water tap and check that all the connections are watertight If any coupling is leaking disconnect the elec trical plug then further tighten the hose clip or nut Connect the appliance to the power supply again When the appliance has been installed for one week tighten the connections for the reject water and feed water hoses again A 24 A leakage as small as just a few drops of water at one end of the purified water hose is enough to start the water purifier working when it is not needed L eakages outside the actual appliance cannot be detected by its leakage protection system U nless specifically stated otherwise in these instruc tions the shut off valve should be left in the open position for the water purifier s protection system to function The flushing procedure You have to work through the steps of the flushing proce dure when the water purifier iS brand new and has never been used before is being brough
6. 8229016 28 USER INSTRUCTIONS Confidence no 400 WATER PURIFIER REVERSE OSMOSIS EN DE FR ES SE PRODUCT DESCRIPTION EN DE FR CON On Ui B WN FP Bracket for reject water hose Reject water hose Hose clips 2 Hose for feed water Angle bracket for purified water hose Filter soanner Information decal Purified water hose Purfied water tap Indicator lights Filter container Base plate Filter container Control panel Knickschutzbogen fur Abwasserschlauch Abwasserschlauch Schlauchschellen 2 Zulaufschlauch Knickschutzbogen fur Reinwasserschlauch Filterschlussel Informationsschild Reinwasserschlauch R einwasserhahn Anzeigeleuchten Filterbehalter Bodenplatte Filterbehalter Kontrolltafel Etrier pour tuyau d vacuation des eaux us es Tuyau d vacuation des eaux us es Attache pour tuyau 2 Tuyau d amen e de l eau Raccord coud pour tuyau de sortie de l eau purifi e Cl pour installation des filtres Fiche d information auto adh sive Tuyau de sortie de l eau purifi e Robinet pour l eau purifi e Voyants d indication Compartiment filtre I Socle Compartiment filtre Tableau de commande ES IT SE U B WN I Abrazadera de la manguera de desag e Manguera de desague Abrazaderas para manguera 2 Manguera del agua de alimentaci n Escuadra para la m
7. Do not attempt to modify or otherwise alter the water purifier in any way Doing so could result in personal injury and or damage to property which would not be covered by any warranty Once every month you should check that the connec tions are all watertight L eakages outside the appliance cannot be detected by the appliance s leakage protection system If the water purifier is malfunctioning it should be iso lated from the electrical supply by removing the electri cal plug from its socket If this is not possible remove the relevant fuse or switch off the circuit breaker at the electrical distribution board consumer unit At the end of the appliance s useful life disconnect the electrical plug from the power supply then cut the elec trical lead at the point where it enters the appliance M ake quite sure that children will not be able to play with the severed lead To find out how best to dispose of the appliance con tact your dealer or the local authority A SAFETY INFORMATION Concerning the use of the water purifier The water purifier is designed to produce the quantity of water normally required for cooking drinks washing dishes and general household duties The appliance needs to remain connected to the water and electrical supplies so that its automatic flushing sys tem can work The appliance will carry out flushing automatically every 12 hours approximately The appliance must not be operated without
8. INFORMATION Consumables accessories Item Item no Filter inserts Filter I particle filter Part no 919 24 00 32 Filter II carbon filter Part no 919 24 00 83 D escaling cleaning agent for Water Purifiers Part no 150 72 07 01 Preservative and Antifreeze liquid for Water Purifiers Part no 150 72 06 02 Sound absorbing carpet Part no 919 24 09 03 Installation pack Part no 919 24 09 04 Connector for dishwashers level control type only Part no 919 24 09 02 Accessories and consumables can be ordered from your dealer When ordering please quote the relevant part number from the list above Recycling of materials 3 T he materials used in 80 of the plastic and rubber com ponents of this product and its packaging are identified by symbols to assist the process of recycling and disposal The materials are marked according to international standards T he cardboard parts of the packaging are made from recy cled paper and should be deposited at a suitable recycling point A BRIEF GLOSSARY Reverse osmosis The purification of water by forcing it under pres sure through a semipermeable membrane The membrane is impermeable to impurities but perme able to water This is the principle upon which the water purifier is based This form of purification does not rely on chemicals M embrane The membrane made of semipermeable material used in the water purifier to purify water by reverse osmosis Filters U sed to separa
9. OR RO 400C PRODUCT NO 919 24 01 17 Position in Description Article no picture RO 400C 230 V CABINET 1 2 3 3B 4 5 5A 6 8 10 12 13 14 15 17 18 19 20 21 22 24 24A 24A 24A 24B 240 24D 24E 24F 24G 24H 241 24 24K 24L 25 Not in picture Not in picture Not in picture Not in picture VALVE RO 400CV 1 OO AION
10. age and protect ing it from freezing The water purifier should be put into storage if it is to be disconnected from water and electricity for an extended period 1 week or more it is not going to be used for a period longer than four months You can choose between two ways of mixing the storage fluid depending on the desired protection against freezing 2 litres of storage fluid 4 litres of water provide protection against freezing down to 15 C 3 litres of storage fluid 3 litres of water provide protection against freezing down to 30 C The correct product Preservative and Antifreeze Liquid can be ordered from your dealer see Consumables and accessories N T his product must be kept out of the reach of children IH 1 Close the valve on the water supply pipe Disconnect the electrical plug and the hose for feed water See Fig A 2 Undo both filter containers as described under Replacing the filters steps 3 6 Remove the two filter inserts and discard them should not be kept for re use Empty the water from the containers 3 Reinstall the empty filter containers back in their normal places M ake sure that each sealing ring is in place in the groove on the top edge of each container 4 Mixthe Preservative and Antifreeze Liquid with water in a bucket dosage see above 5 Put the end of the hose feed water into the mixture M ake sure that the end of the feed water hose remains bene
11. alibrated specifically for your water supply to ensure the correct purification level Calibration should only be carried out when the water purifier is new and has never been used before e the quality of the water supply has changed for some reason such as if you move the appliance to a different locality the membrane has just been replaced T he water produced by the appliance during the calibration procedure must not be consumed INSTALLATION To calibrate the water purifier 35 1 Turn on the tap for purified water Leaving the tap running you must now within 10 seconds press the calibration button see Fig A and then keep it pressed until the indicator lights for Purification Levels and II come on and then go out Then release the button If any of the Purification Level lights I III stay on lit check the five points under the heading First check in the section The flushing procedure then start the calibra tion procedure again from the beginning 2 Allow the appliance to go on producing purified water for at least 10 minutes The lights for Purification Levels and II will now flash once and the current water quality level will be dis played when the light for Purification Level 111 comes on and remains lit indicating the highest purification level If the lights for Purification Levels I II and III flash intermittently in sequence this means that calibration has not been carried out
12. and make quite sure that it is not a problem which you can put right yourself If you have to call out a service engineer to remedy one of the problems in this table you risk having to pay for the service call C yourself T he same applies to faults caused by use of the appli ance for purposes other than those for which it was intended If you have tried everything relevant described in the table and still cannot get your water purifier to work then it is time to call service Service using genuine spare parts is available via your dealer Before calling service it is a good idea to make a note of some appliance details Look for the data plate on the rear of the appliance similar to the one shown in Fig D which will have all the details you need for the water purifier You can record them here D MOD xe ae dh ee dr ee ee ek ee SR ions l I o ET SER NO TYPE wP01 MOD RO 400 Purchase PROD NO 919xxxxxx SER NO XXXXXXXX 230 V 530 W 50 Hz E104 M S IP 21 500 W 18 Dimensions Weight Capacity water temp 15 C Water efficiency Electrical supply T otal power consumption O peration period Sound level when installed in under sink cupboard Environmental specifications alr temperature relative humidity Requirements regarding feed water to the water purifier Chemical requirements
13. anguera de agua purificada Llave de tuercas del filtro Adhesivo informativo Manguera de agua purificada Grifo del agua purificada Pilotos indicadores Portafiltros Base Portafiltros 11 Panel de Control Supporto tubo acqua reflua Tubo di scarico dell acqua reflua nella tubazione fognaria Fascetta stringitubo 2 Tubo acqua di alimentazione Gomito per tubo acqua trattata Chiave speciale per filtri Etichetta informative autoadhesiva Tubo acqua trattata Rubinetto acqua trattata Spie Contenitore filtro Piastra di base Contenitore filtro Pannello di comando H llare f r avloppsslang Avloppsslang Slangklamma 2 Tilloppsslang Vinkelhallare for renvattenslang Filternyckel Informationsdekal Renvattenslang R envattenkran ndikeringslampor Filterbehallare Bottenplatta Filterbehallare 11 K ontrollpanel PRODUCT DESCRIPTION filter li filter e Confidence ro 400 EN DE FR ES IT SE THANK YOU for entrusting us to supply your new water purifier which we hope will provide you with many years of trouble free use To avoid problems it isimportant for you to read through the user instructions and carefully to follow the Safety information and the Installation instructions Everybody using the water purifier should be familiar with how to operate it and its safety features The manual should be
14. ater may develop a certain odour If this is the case it is advisable to disinfect the water purifier and change filters and Il T he disinfectant sodium hypochlorite 3 5 odourless can be bought from supermarkets or from the chemist The water has to be odourless after the disinfection N The disinfectant must be kept out of the reach of children BE 1 Disconnect the electrical plug then plug it back in again to make the appliance switch to flushing mode 2 Undo filter container as described under Replacing the filters steps 3 7 Discard the filter 3 Fill the container three quarters full of lukewarm water and add 25 ml of the correct disinfectant see Fig C 4 Screw the container containing the solution back onto the appliance with the aid of the filter spanner 5 Turn on the tap for purified water and let the water purifier operate for 45 seconds 6 Whilethe tap is still on open disconnect the electri cal plug see Fig B Then turn off the tap and leave the water purifier like this for about 30 minutes 7 Restart the water purifier by reconnecting the electri cal plug to the wall socket let it flush automatically 8 Undo the filter containers and insert a new filter 11 Also change filter according to Replacing the filters 9 Refit the front cover 10 Work through all the steps of the full Flushing pro cedure MAINTENANCE 13 MAINTENANCE Preparing the water purifier for stor
15. ath the surface throughout see Fig B 6 Connect the electrical plug again T he water purifier will now automatically pump the mixture inside the appliance After 40 seconds disconnect the electrical plug R epeat this step until all the mixture has been drawn up D isconnect the electrical plug L eave the tap open and dis connect the inlet hose and the pure water hose from the water purifier Disconnect the pure water hose by pressing in the grey ring on the connection and pulling out the hose see fig C You have now prepared the water purifier for storage It can be left in this state for up to nine months A When the water purifier is to be brought back into use you must stand it somewhere where the temperature is above 45 C for at least 48 hours e Work through all the steps of the full Flushing proce dure to remove the preservative Install new filters and 11 see Replacing the filters 14 To clean the grid The grid a coarse filter is designed to intercept large par ticles and is located inside the connection for the feed water on the appliance I f the indicator lamp for filter I shows that the intake pressure is too low the reason may be that the grid is clogged IS 1 Turn off the tap for purified water D isconnect the appliance from the electrical supply 2 Close the valve on the water supply pipe 3 Undo the feed water hose connector on the appliance 4 Usesuitable pli
16. conductivity salt chloride cloudiness turbidity pH calcium 2 magnesium M 92 hardness iron Fe2 iron Fest manganese Mn COD Mn O5 higher values require an extra prefilter Microbiological requirements H eterotrophic bacteria 48 hour test count Coliform bacteria E coli Water flow D omestic water supply pressure Water temperature TECHNICAL DATA height 466 mm depth 460 mm 395 mm without hand grip and hoses width 225 mm 29 kg when supplied 33 kg when filled with water 3 1 30 4 litres minute approx 80 at constant flow approx 50 75 including flushing 230 V 50 Hz IO A earthed socket 530 W 20 minutes 60 dB A 2 43 25 95 200 mS m 1500 mg 900 mg I sight distinct 1 FNU 4 10 140 mg 20 d 5 mg 0 3 mg I 0 8 mg 10 mg 1000 ml 1000 100 ml 100 100 ml gt 10 l min 150 1000 kPa 1 5 10 bar 2 40 C 19 TECHNICAL DATA Examples of rejection for substances which may be present in water INORGANIC SUBSTANCES turbidity cloudiness gt 99 colour gt 99 Cations Metals sodium gt 96 potassium gt 97 calcium hardness gt 99 aluminium gt 99 iron gt 99 manganese gt 99 Cations Heavy metals copper gt 99 lead gt 99 zinc gt 99 mercury gt 99 cadmium gt 99 chrome gt 98 nickel gt 99 Anions fluoride gt 39 Chloride gt 98 nitrate 29 sulphate
17. e appliance There must be a gap of 20 mm between the sides of the water puri fier and any adjacent fitments or walls The connection points of the water purifier allow you to route hoses and cables in any direction out from the appliance The dimensions required for the installation site are shown in Fig A When installing the appliance make quite sure that none of the service connections get crushed L ter which method vou choose there are certain points le a which you should be careful to observe gm Thewater purifier must be installed in the upright position N The water purifier may only be installed with the accompanving tap T he water purifier must not be connected so as to supply all the taps in the property with water There is a risk of corrosion in water pipes and water heaters N either may the water purifier be installed in connection with valves switches or tanks Anv faults that arise in a water purifier that has been incorrectiv installed are not covered by the guarantee Apply the information panel IS In the box of accessories you will find a sheet of self adhesive information panels in several lan guages Select the language required and apply the printed panel to the part of the appliance shown in Fig B 21 INSTALLATION Electrical and plumbing connections The illustration reproduced in Fig C is also to be found on the rear of the appliance to show how the various connections shou
18. e points to ensure that the connec tion will be fully watertight Install the two hose inserts one at each end of the hose for purified water MI 1 Mark the centre of the place where the purified water tap is to be installed M ake sure that there is enough room below the worktop for the purified water hose to be attached beneath this point 2 Drilla16 mm hole 3 Remove the small section of protective tubing and install the main tap pipe on the tap assembly Install the whole tap on the worktop sink bench as shown in Fig F1 The worktop or bench must be no thicker than 35 mm Screw the quick connector fit ting onto the main thread protruding from the bot tom of the tap assembly Then press the end of the purified water hose all the way home into this quick connector as far as the line marked on the hose about 17 mm see Fig F2 22 Connecting the reject water hose The reject water hose for discharge of water to a household waste pipe can be extended up to 4 metres The smallest inter nal diameter is 13 mm The bracket supplied should be secured at a height of at least 50 mm and a maximum of 500 mm above the top of the appliance 057 Connection to a waste pipe with be made if the trap has entry point of type used for dish washer discharge If there is only one entry point and this is already in use the connector unit will need to be changed and one with two entry points used
19. e sealing ring is in place in the grooves of the filter container 9 Refit and tighten the container using the filter spanner Tighten the filter container so that the dot is some where between the two outermost white lines 10 Slide the filter containers back into the appliance 11 Close the front cover and reconnect the electrical plug Flushing will take place automatically COM Ul This completes the procedure for replacing filter I and the water purifier is ready for use again TO REPLACE FILTER II Replace filter 11 when the indicator lamp for filter II comes on and when you notice a three second delay before the motor starts up each time you turn on the tap pep 1 11 Work through the 11 steps in the instructions for replacing filter but remove container II instead on the right and replace the filter in that 12 For filter II you have to finish by resetting the appliance M ake sure that the tap purified water is turned off and the electrical supply is connected Then press the Calibration button on the control panel and keep it pressed inwards until the pattern of indicator lights for filter II has gone out takes about five seconds This completes the procedure for replacing filter II and the water purifier is ready for use again 10 MAINTENANCE MAINTENANCE Descaling In time the substances which the appliance removes from your drinking water tend to clog the membrane and will eventuall
20. ed water The water purifier produces purified water when the tap is moved B to either of the On positions shown in Fig B IS When the tap lever is moved to Position 1 the tap will stay on hands free at maximum flow until the lever is moved back manually to the O ff position Thelever has to be pressed and held when Position 2 IS used also maximum flow The indicator lights on the tap show the current water quality green light optimum water purification level red light unacceptable water purification level N If the water purifier has not been used for a time it may take up to 60 seconds before the optimum water purifi cation level is reached as shown by lights on the tap and control panel The water purifier has automatic features designed to opti mise the service life of the membrane e Just after you draw water each time the appliance will switch to flushing mode automatically to clean the membrane The length of this flushing will vary 5 to 90 seconds according to how long the tap was open i If thetap isleft on for longer than 20 minutes the appli ance will shut down automatically To restart it follow the instructions in the T rouble shooting table e Theappliance will switch automatically to flushing mode for a brief period once every 12 hours approxi mately provided the water and power supplies are con nected This periodic flushing takes place no matter when the appliance was las
21. ers 10 11 IIS SCANNING sisien 12 13 Disinfection i 13 Preparing the water purifier for storage and protecting it against freezing 14 To clean the grid 15 REGULAR CARE OF WATER PURIFIER 15 Points to remember 15 IF THE WATER PURIFIER STOPS WORKING 16 18 Trouble shooting table 16 17 16 adjust the TA s sisien o 18 Service and spare parts 18 Guidelines for using the user instructions CONTENTS For the installer TECHNICAL DATA 19 20 INSTALLATION 21 25 UTI ACI 16 p 21 Where to install the water purifier 21 Apply the information panel 21 Electrical and plumbing connections 22 To fit the tap for purified water 22 Connecting the reject water hose 23 Connecting the feed water hose 23 Connecting up the appliance 24 The flushing procedure 25 Calibration 25 Moving the water purifier 25 The following symbols in the text will help you to read the user instructions N Safetv information d Environment information IS Step by step instructions i Tips and information G
22. ers to grip and remove the grid Fig D 5 Clean the grid and run water through it before putting it back inside the connector 6 Reconnect the feed water hose to the appliance 7 Open the valve on the cold water supply pipe and check that there are no leaks 8 Connect the appliance to the electrical supply again It will flush automatically MAINTENANCE REGULAR CARE OF WATER PURIFIER Listed below are the things you need to remember in the regular care of your water purifier The points are listed in the order of frequency starting with daily checks Points to remember Check the indicator lights every day in case there is some state or function which needs attention e The everyday care of the water purifier consists basl cally of keeping it clean The outside of the appliance should be cleaned with a damp cloth only Do not use a wet cloth and do not pour water over it for cleaning Do not use any cleaning agents e Once a month check that all connections to the appli ance are properly secured and watertight Wipe dry any condensation which may have accumulated inside the appliance base L eakages outside the appliance can not be detected by the appliance s leakage protection system The appliance needs to be descaled at regular inter vals The frequency depends on the hardness of the water supply and its microbial content Besureto replace the filters as soon as necessary The life of these filters is deter
23. gt 9 ORGANIC SUBSTANCES Hydrocarbons heptane octane decane etc gt 98 benzene toluene xylene ethyl benzene etc gt 99 diesel oil gt 99 Polyaromatic hydrocarbons 399 PAH Chlorinated hydrocarbons 599 Compounds which can form when water is chlorinated Trihalomethanes 560 trichloromethane 399 bromodichloromethane dibromochloromethane tribromomethane Pesticides PCB vus MICROORGANISMS 599 heterotrophic bacteria 48 hr test 599 coliform bacteria E coli Notes The values for the inorganic substances were measured in a sample of water which was taken after two minutes opera tion at a flow of 4 4 litres per minute 80 recovery and a challenge water with a salt content of 800 mg per litre at a temperature of 20 C Test laboratory VVL Stockholm Sweden The values for the organic substances were measured in a sample which was taken after two minutes operation at a flow of 2 8 litres per minute 80 recovery and a challenge water to which was added each relevant substance to a concentra tion which is 100 times higher than the lowest detectable quantity at a temperature of 10 C T est laboratory AnalyC en Lidkoping Sweden Microbiological testing was carried out under a range of operating conditions with a challenge water containing a very great number of microorganisms T he water samples were collected weekly after operating times of 20 and 40 seconds and 1 2 6 12 and 18 minutes Test laboratory SVELAB J
24. instead The reject connector from the water purifier should be before the drain The reject water hose needs to be routed in acurve up the underside of the worktop or sink bench Fix the hose securely in place as shown in Fig A using one of the hose clips and the bracket supplied Connecting the feed water hose JE M ake sure that the black washers are in place when securing the connectors at both ends of this hose Screw the straight end of the feed water hose onto the shut off valve see Fig B If the 3 4 hose connection does not fit it can be changed to a 1 2 connection using the adapter sup plied Put the black washer in the adapter and screw the adapter onto the shut off valve for feed water Screw the feed water hose onto the adapter INSTALLATION 23 INSTALLATION Connecting up the appliance Before moving the water purifier into its permanent place connect the three hoses to the appliance as shown in Fig C JE A Connect the purified water hose from the purified water tap to the appliance Press this end of the hose all the way home as far as the line marked on it about 17 mm U se the elbow supplied if space is restricted behind the appliance Connect the end of the reject water hose the one with the bend to the appliance and secure it with one of the hose clips supplied N ext screw the feed water hose onto the appliance O pen the valve to check that the hose is fully watertight Connect
25. ld be made The water purifier is connected to the cold water supply tem perature range 2 40 C via a polyethylene feed hose 3 The cold water pipe should have a valve easily accessible for shut ting off the supply see Fig D If the appliance is being con nected to new pipes or pipes which have been out of use for some time the water should be allowed to run for a while before you connect the hose This will prevent the appliance intake filter referred to here as the grid from getting blocked by sand or rust The appliance has two outward water hoses The purified water is taken via the purified water hose 1 to a separate tap while the reject water is connected directly to a waste pipe via the reject water hose 2 The water purifier must be connected to an earthed electrical supply 230 V 50 Hz 10 A We recommend use of a plug in connection to a wall socket since certain procedures such as replacing filters and preparing the appliance for storage if it will not be used for a time require the power supply to be dis connected then reconnected Using an electrical plug also makes it easier to move the appliance To fit the tap for purified water Avoid cutting the hose for purified water even if it is too long If it must be cut do so with a very sharp knife such asa Stanley knife making sure that the cut is straight and clean and that the hose is not deformed by cutting see Fig E It is important to observe thes
26. mined by amongst other factors the levels of impurities in your water supply If the water supply has been classified as unfit for drinking the water from the appliance should be tested once per year e After replacing filters leave the discarded filter insert to drain for afew minutes T hese filters can be dis carded in your ordinary household refuse since they do not contain any substances which are hazardous to the environment 15 IF THE WATER PURIFIER STOPS WORKING Trouble shooting table To protect both the user and the appliance itself from incorrect use the water purifier has built in warning alarm devices which cause it to stop working under certain conditions The table below lists these warn ings and their probable causes The indicator lights have three statuses SYMPTOMS POSSIBLE CAUSE 16 Light off Lighton 2e Light flashing Time to replace filter or clean the grid ACTION TO TAKE There is time before the water purifier experiences an emergency stop Prepare to replace filter and to clean the grid The feed water s pressure is too low i e less than 1 5 bar 150 kPa Warning that filter I or II is blocked Check the feed pressure If necessary increase the pres sure to 1 5 10 bar 150 1000 kPa Check that there is nothing inside the filter containers which could be blocking the flow If necessary replace filter or 11 Warning of blockage In grid Check the grid
27. ompagne le purificateur en cas de d placement ou de vente de ce dernier de facon ce que tout utilisateur puisse tout moment consulter le manuel d instructions complet et les instructions de s curit Le manuel d instructions en francais commence la page 49 GRACIAS por confiar en nosotros al adquirir su nuevo purificador de agua del que esperamos que disfrute por muchos afios sin ning n tipo de problema Para evitar problemas es importante que lea el manual de instrucciones y que siga con atenci n la Informaci n sobre seguridad y las instrucciones de Instalaci n Cualquier persona que utilice el purificador de agua deber estar familiarizada con el funcionamiento y las advertencias de seguridad Conserve el manual pr ximo al purificador de agua incluso si se coloca en otro sitio o cambia de propietario para que quien lo utilice pueda conocer las distintas funciones y las instrucciones de seguridad El manual de instrucciones en espanol comienza en la p gina 71 GRAZIE per la fiducia che ci avete accordato acquistando questo nuovo depuratore d acqua Siamo certi che potrete contare sul suo perfetto funzionamento per molti anni Per evitare problemi importante che l utente legga attentamente le seguenti istruzioni prestando particolare attenzione ai capitoli I nformazioni sulla sicurezza e Installazione Chiunque utilizza un depuratore dovrebbe conoscere le modalit di funzionamento e le caratteristiche di sicure
28. pliance has finished flushing Leave the electrical supplv to the appliance on 3 Undo filter container 11 as described under Replacing the filters steps 3 7 4 Measure 250 ml corresponds to 200 grams of the descaling agent into the container Fill the container almost to the top with lukewarm water 20 40 C Stir until the powder has dissolved see Fig A 5 Screw the container into place with the aid of the fil ter spanner 6 Turn on the tap for purified water and let the water purifier operate for 45 seconds 12 FREQUENCY OF DESCALING Calcium 2 8 magnesium Mg mg l Frequency of descaling d 50 every 6 months 50 100 every 3 months 100 140 7 While the tap is still on open disconnect the elec trical plug see Fig B Then turn off the tap Now leave the water purifier like this for about 10 hours e g over night 8 Attheend of the 10 hours undo the container Discard its contents and rinse it with water 9 Put the filter back in the container and follow steps 8 11 as described under Replacing the filters except that you put back the filter which has already been used 10 Work through all the steps of the Flushing procedure This completes the descaling procedure The water puri fier is ready for normal use again Disinfection If the appliance has not been used for a time several days there may be a build up of microorganisms on the membrane and the w
29. r dam age to property which are not covered by any warranty Any plumbing work required should be carried out by a qualified tradesman If you do any of the installation work yourself you must check the regulations which apply to this and comply with them It isimportant that the water purifier should be installed in the upright standing position M ake sure that hoses and leads do not get crushed or otherwise damaged when the water purifier is being moved e g during installation or cleaning T he water purifier must not be plumbed in to supply the entire dwelling with water since this could cause corrosion inside water pipes and hot water heaters For the same reason no tap should be used for drawing the water from the appliance other than the one supplied or one recommended by your dealer Child safety N ever leave packaging material lying around so that children can play with it Do not let children play with the water purifier USING THE WATER PURIFIER Once the water purifier has been installed and calibrated according to the Installation instructions it is ready for use The water purifier has an electronic control system which makes it easy for you to use Normally you will only need to remember a few points To replace Filters and II once or twice a year or when the indicators on the front panel show they need replacing To descale the water purifier at the intervals recommended To draw purifi
30. rky than the tap can handle The adjusting screw on the tap needs adjusting When the purifier is not in use with the Work through all the steps of the full electricity disconnected and there is bio Flushing procedure logical growth in the water or unpleasant odour can occur If the appliance has shut down automatically it will have to be restarted by disconnecting then reconnect ing the electricity If a problem persists even after you have tried to trace it and correct it using the trouble shooting table con tact your dealer 17 IF THE WATER PURIFIER STOPS WORKING To adjust the tap A SE 1 Disconnect the electrical plug 2 Pull the main tap pipe straight upwards as illustrated Fig A 3 Press and slide the tap lever across the top of the hole for the main tap pipe Fig B 4 Adjust the screw Fig C C1 If the flow from the tap is uneven or jerky Turn the adjusting screw one half turn clockwise C2 If the appliance starts working on its own Turn the adjusting screw one half turn anticlockwise 5 Refit first the lever then the main tap pipe Check that the seals washers on the main tap pipe are in good condition 6 Reconnect the electrical plug and let the water purifier B flush automatically 7 Test the appliance If the problem persists adjust the screw further Service and spare parts If a fault arises first work through the trouble shooting table f the water purifier stops working
31. t back into use after having been stored using the Preservative Antifreeze liquid e has been cleaned to wash away the cleaning agent e has been fitted with a new membrane N o water from the appliance should be con sumed until you have completed the full Flushing procedure A First check that the drinking water tap is turned off that the shut off valve on the cold water pipe for the feed water is open that there are no leaks at the connection between domestic water supply and appliance that the reject water and purified water hoses are connected with no leaks that the filter containers are properly tightened Remove the electrical plug from the wall socket 2 Connect the electrical plug to the wall socket again The water purifier will now switch auto matically to flushing mode 3 When it stops pull out the electrical plug then plug it back in to make the appliance go through another flushing cycle 4 Repeat step 3 so the appliance goes through a third flushing cycle 5 Turn on the purified water tap and leave it run ning for ten minutes Then turn the tap off The appliance will switch automatically to flushing mode again When the appliance is brand new or when the mem brane has just been replaced 6 Follow the calibration procedure described below When just flushing 6 Repeat step 5 above The water purifier will now be ready for use Calibration The water purifier needs to be c
32. t used W When using the water purifier it is sensible to fill a jug with drinking water while it is operating Trv to avoid starting it working just to fill a single glass at a time This helps save water because each time the appliance purifies water a certain amount is lost via the reject water outlet before the optimum purification level is reached and the water purifier also switches to flushing mode after it is used MAINTENANCE Replacing the filters It is important to replace the filters as soon as they need replac ing since their main function is to protect the membrane C heck for any signs of leaks just after you have replaced them and again after you have used the appliance a few more times TO REPLACE FILTER I R eplace filter I when the indicator lamp for filter I comes on IS 1 Make sure that the tap for purified water is turned off and that the appliance is not flushing 2 Disconnect the electrical plug Open the front cover In front of the two filters as shown in the illustration 3 Pull the filter containers outwards as far as they will come 4 Usethe filter soanner to undo the container to the left marked Bear in mind that the container will be full of water and that some water may spill M op up any water inside the base of the appliance Remove the old filter Clean the filter container with water and a brush Put the new filter in place with the label pointing upwards M ake sure that th
33. te out material before the water reaches the membrane prolonging the life of the membrane grid a coarse filter particle filter Filter carbon filter Filter Il N SAFETY INFORMATION The Confidence RO 400 is a very safe appliance but even so it is important that everyone using it should be thoroughly familiar with the way it works and its safety features To prevent mishaps and problems you should read the Safety Information on these pages and carefully follow the instructions in the Installation section Take care of this manual and make sure that it accompanies the water purifier if it is moved or sold The water purifier may only be installed with the accompanying tap The water purifier must not be con nected so as to supply all the taps in the property with water There is a risk of corrosion in water pipes and water heaters N either may the water purifier be installed in connection with valves switches or tanks Any faults that arise in a water purifier that has been incorrectly installed are not covered by the guarantee Check that the water you intend to purify meets the requirements listed under Requirements of feed water in the section T echnical data When the water purifier is brand new the purified water must not be consumed until after the calibration and flushing procedures have been completed Calibration of the water purifier should only be carried out the first time that
34. the filters being in place except during the descaling or storage procedures Doing so can cause serious damage If the tap is left on for longer than 20 minutes the water purifier will shut down automatically The appliance is designed to do this mainly to maximise the service life of the membrane To restart the appliance follow the instructions in the T rouble shooting table The top of the water purifier should not be used as a place for storing anything Do not use the water from the appliance in aluminium Saucepans etc on account of the risk of corrosion which would also cause increased levels of aluminium in the water The appliance will flush automatically after water iS drawn from it and also whenever the electrical supply is reconnected See To draw purified water Concerning installation and service The water purifier must be connected to an earthed electrical supply We recommend use of a plug in con nection to a wall socket since certain procedures such as replacing filters and preparing the appliance for storage if it will not be used for a time require the power supply to be disconnected then reconnected U sing an electri cal plug also makes it easier to move the appliance If the appliance is to have fixed wiring to the electrical supply this work must be carried out by a qualified trades man Installation work which has not been carried out properly can result in serious personal injury and o
35. the water purifier is used if the appliance is moved to a different place locality where the water quality is different after the membrane has been replaced When the membrane contains the special products for storage or descaling it will have to be cleaned by fol lowing the Flushing procedure before the water from the water purifier may be used again The water produced by the appliance may only be con sumed if Purification Level indicator II or III on the control panel comes on A green indicator light on the tap will come on at the same time If the feed water supply to the appliance is unfit for con sumption have the purified water from the appliance tested after installation You should subsequently have the purified water tested once a year or if any change In its taste or smell occurs to ensure that the water purifier is functioning well If the result is unsatisfactory do not drink the water Contact your dealer If any leakage arises turn off the supply of water to the appliance immediately and disconnect the appliance from the electrical supply by removing the electrical plug from the wall socket or if necessary removing the relevant fuse If the water purifier is to be disconnected from water and electricity for an extended period 1 week it should be stored as described in Preparing the water purifier for storage and protecting it from freezing This also provides protection against freezing
36. will be ready for use again Restart the appliance by disconnecting and then recon necting the electricity to start flushing mode Recalibrate the water purifier see Calibration Restart the appliance by disconnecting and then recon necting the electricity to start flushing mode Wait for two hours Turn on the tap wait for 2 minutes IF THE WATER PURIFIER STOPS WORKING SYMPTOMS POSSIBLE CAUSE ACTION TO TAKE Low water flow The membrane may be clogged Descale the appliance See D escaling The hose for purified water is not pressed C heck all connections The appliance starts all the way home at the connection on the C heck that both ends of the hose for purified working on its own appliance Alternatively there may be a water are cut straight and clean and not briefly without tap leak at the connection of hose to tap or deformed Should be round not oval in shape being turned on the hose for this tap may have been short ened cut incorrectly The tap is leaking which causes the water Adjust the adjusting screw on the tap see purifier to respond constantly to the loss To adjust the tap of pressure The adjusting screw in the tap may need adjustment or washers in the tap may be damaged The flow of water trom If the temperature is higher than 30 C Adjust the adjusting screw on the tap see the appliance is uneven the flow rate will increase to a level higher To adjust the tap or je
37. y reduce the flow of pure water from the tap To prolong the ser vice life of the membrane it has to be descaled periodically When you notice that the flow rate from the tap has decreased you need to follow the descaling procedure below The time schedule for how often you will need to do this will depend on your particular water supply especially on its levels of calcium hardness see table right iron manganese and possibly sill con as well as of microorganisms Even with regular descaling the maximum flow of purified water from the appliance will decrease gradually on account of the normal properties of the membrane When you notice that despite descaling the flow is about half of what it was when the membrane was new it is time to replace the membrane D escaling the appliance takes about ten hours during which time you will not be able to use the appliance You should descale your water purifier when the flow of water from the tap has decreased e at the intervals recommended in the table right The correct descaling product for this appliance can be ordered from your dealer see O ptional accessories and consumables A The descaling product must be kept out of the reach of children Wash vour hands after using it 3 1 Disconnect the electrical plug then plug it back in again to make the appliance switch to flushing mode 2 Make sure that the tap for purified water is turned off and that the ap
38. zza di tale apparecchio Conservare il presente manuale assieme al depuratore Se l apparecchio viene spostato o ceduto a un altro proprietario l utente deve sempre avere la possibilit di consultare la documentazione relativa alle varie funzioni e alle istruzioni di sicurezza Leistruzioni in italiano del manuale iniziano a pagina 93 TACK f r att vi fick f rtroendet att leverera din nya vattenrenare som vi hoppas du ska f m nga ars bekymmersfri anv ndning av F r att undvika problem r det viktigt att du l ser igenom bruksanvisningen och noga f ljer sakerhetsinformationen och installationsanvisningarna Alla som anv nder vattenrenaren ska vara v l f rtrogna med anv ndningss ttet och s kerhetsdetaljerna Spara bruksanvisningen och l t den f lja med vattenrenaren vid flytt eller garbyte s att alla som anv nder vattenrenaren kan l sa om funktionerna och s kerhetsdetaljerna Bruksanvisningens svenska instruktion b rjar p sida 115 For the user GENERAL VIEW OF THE APPLIANCE 2 3 CONTENTS D INFORMATION 6 Consumables accessories 6 Recycling of materials aa 6 A DIET QIOSSALY sica 6 SAFETY INFORMATION 8 Concerning the use of the water purifier 8 Concerning installation and service 8 sro 8 USING THE WATER PURIFIER 9 To draw purified 9 MAINTENANCE 10 15 Replacing the filt
Download Pdf Manuals
Related Search