50003564 - R1 - SB Assy EN.cdr
Contents
1. Side Burner Assembly Kit No VCS35SB For all properly equipped Vermont Castings Models except Built In models Note Before proceeding with the installation make sure this side burner kit is designed to burn the same type of gas as your grill LP Propane or NG Natural Gas Caution Some parts may have sharp edges to avoid injury wearing gloves during assembly is strongly recommended Tools Required Philips or Robertson Screwdriver pliers Step 1 Attach Valve Bracket to Valve Attach the valve bracket to the valve with 2 6 x 1 4 Bolts as shown in Fig 1 Step 2 Assemble the Valve to the Side Burner From under the side burner assembly position gt es m and align the valve assembly to the burner and lt IDE TS P e venturi as shown in Fig 2a Fasten the valve f y Seana using 2 8 screws from the top of the side AIX burner Ensure the valve outlet is properly inserted into the burner venturi a minimum of 1 4 6mm as shown in Fig 2b Valve Outlet k Step 3 Attach the U Clip Fasteners Attach the 3 U Clip fasteners to the three bolt hole locations along the left and front of the side burner assembly as shown in Fig 3 Make sure the flat side of the U Clip fasteners are facing the inside of the assembly Do not attach U Clip fasteners to the right side of the side burner assembly Step 4 Attach the Top Cover remove the st2. ainless shelf insert where the side burner assembly will be mounted Note The side burner frame that is shown marked with is used for built in models only For standard grills the side shelf is used as the side burner frame Attach the top cover using 2 shoulder screws at the hinge points of the cover as shown in Fig 4 Be sure the top cover can open and close freely do not over tighten the screws Attach caution sticker as shown Side Burner Assembly Step 5 Assemble the Side Burner to the Side Shelf Frame Position the side burner assembly from the bottom into the side shelf frame as shown in Fig 5a Make sure the side burner flanges are outside of the frame flanges Fasten the assembly using 3 8 x 1 2 bolts into the U Clip fasteners along the left side and front Use 2 8 x 1 2 bolts and nuts on the right side Fig 5b Tighten the bolts securely Step 6 Install the Knob Cooking Grate Attach the valve control knob to the valve stem as shown in Fig 6a Set the cooking grate over the burner as shown in Fig 6b Step 7 Attach Connector Hose to the Grill Remove the knock out slug from the top front corner of the right cabinet side panel And insert the plastic snap bushing Position the end of the side burner hose through the bushing into the base cabinet Connect the end of the hose to the gas supply by snapping it into the female quick connect fitting provided at the tee of the gas pres
3. sure regulator LP models or the gas supply line natural gas models This is accomplished by pulling back the outer ring of the female coupling inserting the male fitting of the hose fully then releasing the ring The hose should be positively engaged Step 8 Leak Check Turn on the gas at the cylinder LP models or main valve natural models DO NOT turn the side burner valve on Perform a leak check at all connections and fittings by brushing or spraying a 50 50 solution of dish soap and water If any bubbles appear correct the leak before attempting to light the side burner or the grill Refer to the User s Manual for lighting and use instructions Replacement Parts Igniter and Knob 50000367 Hose Assembly 50001092 Valve Knob 50000113 Valve Nat Gas 50001045 Burner 50001044 Valve LP 50001046 Grate Cast 50001035 Electrode 50000115 Grate Wire 50003050 50003564 11 06 Rev 1 CFM CFM Corporation 410 Admiral Boulevard Mississauga Ontario L5T 2N6 Canada 800 668 5323 www cfmcorp com
Download Pdf Manuals
Related Search