Vivitek Q4 User Manual English
Contents
1. AN Important Enter Change settings in the OSD Enter function when using Web Browser Right Cursor Navigate and change settings in the OSD Cursor navigation when using Web Browser Down Cursor Navigate and change settings in the OSD Cursor navigation when using Web Browser Exit Close the OSD Exit function when using Web Browser Mute Mute the built in speaker Source Change the input source Volume Up Down Change the volume 1 Be sure nothing obstructs the path between the remote control and the Qumi If the path between the remote control and the Qumi is obstructed the signal can bounce off certain reflective surfaces 2 The buttons and keys on the Qumi have the same layout and similar functions as the corresponding buttons on the remote control This user s manual describes the functions based on the remote control Note The Web Browser and the speaker are only available in the Q5 Series Qumi and Remote Control Buttons The Qumi can be operated using the remote control or the keypad on the top of the Qumi All operations can be carried out with the remote control however the keypad on the Qumi carries out the same operations as the remote control by pressing a combination of keys The remote control is not only used to navigate the cursor in the menus but can also be used to control the media functions music and video playback For more details about how to co2. Connecting Video Connect video devices to the Qumi by using the audio video cable Optional Game DVD Console Player Connecting Audio Connect earphones or mini speakers to the Qumi by inserting into the Audio Out port Earphone Mini Speaker D Starting and Shutting down the Qumi 1 Connect the AC power adapter to the Qumi Connect the other end of the AC power adapter to a wall outlet Note Adapter models may vary between regions I Press the O POWER button to turn on the Qumi The Qumi splash screen displays and connected devices are detected See Setting an Access Password Security Lock on page 11 if security lock is enabled 3 f more than one input device is connected press the SOURCE ci PE button on the remote control HDMI MHL and use the A or Y buttons to USB select the applicable device or press A and Y or lt and at the same time on the keypad on the Qumi e VGA Analog RGB Component DVD input YCbCr YPbPr or HDTV input YPbPr VGA e Composite Video Composite Vida Traditional composite video C HDMI MHL HDMI MHL HDMI DVI MHL USB USB disc Available in Q5 Series I 4 Press the O POWER button to turn off the Qumi 5 When the Power Off Press Power again message appears press the 5 POWER button The projector turns off Adjusting the Image If the projected image is not clear the image can be adjusted
3. 16X 32X Photos gt Supported Formats The photo viewer can open the following types of image files BMP up to 4000 x 3000 pixels e PNG up to 4000 x 3000 pixels e JPG up to 4000 x 3000 pixels Viewing Your Photo When a USB storage drive is inserted the storage card folder icon will display in the file directory To open a photo in photo viewer perform the following 1 Press the lt or button to select the Photo icon in the media suite menu 2 Press to open the file directory 3 Select the folder containing the desired photo 4 Press to display the desired photo To view the details of the photos navigate to a photo The details of the photo will appear on the bottom of the screen To view photos in full screen mode perform the following 1 Navigate to a photo 2 Press to view the photo in full screen mode To utilize the Zoom In tool press i 2X 4X 8X 16X In order to zoom out to the default size of the image press the Exit key While a photo is displayed the control interface can be hidden To hide the control interface press the A button Press the A button again to show the control interface Control Interface The photo viewer contains the following controls ACTION DESCRIPTION ep Return to the previous menu Sets the Slide Show interval S T prensese Gra EE Office Viewer Supported Formats The document viewer in the Qumi Media Suite can open
4. gt button to enable or disable presentation timer Timer l function Press the lt or gt button to adjust the display timer period Press lt to reset presentation timer counter 36 Installation Il Menu To access the Installation II menu and adjust the settings perform the following steps 1 Enter the OSD menu 2 Press the lt or gt button to select the Installation Il menu 3 Press the A or Y button to move the cursor up or down in the Installation Il menu Installation Il Auto Source Off Auto Power Off min D Auto Power On Off LED Mode Normal Advanced Factory Reset tatus ITEM DESCRIPTION Press the lt or gt button to enable or disable automatic source Auto Source detection Press the or gt button to automatically turn the projector lamp AUO Power ON mn off when there is no signal Auto Power On Press the or gt button to enable or disable automatic power on Press the or gt button to select the LED mode for higher Bode brightness or lower brightness to save LED life Press to enter the Advanced menu See Advanced Feature on A dvanced page 38 Factory Reset Press lt to reset all items to factory preset values Press lt to enter the Status menu See page 41 for more Status information on Status 37 Advanced Feature To access the Advanced menu and adjust the settings perform the following steps 1 Enter the OSD menu 2 Press the lt or
5. 11 the password confirmation menu appears when you power on the Qumi when the KI Security Lock is enabled asa C Menu Cancel created in step 5 Important Keep the password in a safe place Without the password you will not be able to use the Qumi If you lose the password contact your reseller for information on resetting the password Using a Tripod Available in Q5 Series The Qumi can be used with a tripod by connecting the tripod to the bottom of the Qumi Many typical tripods can be connected Supported Tripod Specifications e Type Mini tripod e Slot size 1 4 20 L6 3 mm Note Remove sticker before use Setting Up the Remote The remote control comes with one 1 3V lithium battery CR2025 The battery is pre installed in the remote control To begin using the remote control remove the plastic tab A from the battery compartment i Replacing the Remote Control Batteries compartment cover battery and insert by sliding the cover the new battery towards the arrow with the positive A Then pull out side facing up the cover towards the arrow B 1 Remove the battery 2 Remove the old 3 Install the cover Caution 1 Use only a 3V lithium battery CR2025 2 Dispose of used batteries according to local ordinance regulations 3 Remove the battery when not using the Qumi for prolonged periods Operating Range The remote control uses infrared IR transmi
6. 32mm 1 27 50 Regulatory Compliance FCC Warning This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his her own expense Changes or modifications not expressly approved by the parties responsible for compliance could void the user s authority to operate the equipment Canada This class B digital apparatus complies with Canadian ICES 003 Safety Certifications FCC B UL CCC CE C Tick KC CB SASO NOM PCT RoHS ICES 003 Canada Disposal and Recycling This product may contain other electronic waste that can be hazardous if not disposed of properly Recycle or dispose in accordance with local state or federal Laws For more information contact the Electronic Industries Alliance at www eiae org 51
7. Check to see if the battery polarity is correct Replace the batteries Turn off other Infrared enabled devices in the vicinity Si pr e a amp Ze Have the remote control serviced 44 Audio Problems Problem There is no sound 1 Adjust the volume of the audio source 2 Check the audio cable connection 3 Test the output of the audio source with other speakers 4 Have the Qumi serviced Note The speaker is only available in Q5 Series Problem The sound is distorted 1 Check the audio cable connection 2 Test the output of the audio source with other speakers 3 Have the Qumi serviced FAQs 1 Does Qumi work with a personal computer notebook or netbook Yes Use the provided VGA cable or HDMI cable The Qumi can connect to a PC notebook or netbook if they have an appropriate HDMI or VGA port To play audio a separate 3 5mm stereo mini jack audio cable is required to connect to the Qumi s audio port Is it possible to connect the Qumi to a game console such as a Microsoft Xbox or Sony PS3 Yes The Qumi can be used to display content from an Xbox or PS3 console This can be done by connecting the HDMI cable from the game console to the Qumi Can the Qumi project content from a television Watching television content can be done by connecting a cable box digital set top box or satellite receiver because televisions are only able to produce images on its own screen For example
8. MENU button or Exit on the remote control to close the OSD or close a submenu Note Depending on the video source not all items in the OSD can be modified For example the Horizontal Vertical Position items in the Computer menu can only be modified when the Qumi is connected to a PC through a VGA cable Settings that are not enabled or that cannot be modified are gray in color 25 Setting the OSD Language The language that is displayed in the OSD can be changed To change the language in the OSD perform the following steps 1 Enter the OSD menu Press the lt or gt button to select the Installation menu e Video f Audio Menu Select 4 gt Scroll 4 w Menu Exit item Adjust 4 gt Scroll Aw 3 Press the lt or gt button until the language you want is shown in the cursor 4 Press the EXIT button or MENU button twice to close the OSD 26 OSD Menu Overview Use the following illustration to quickly find a setting or determine the range for a setting MAIN MENU SUB MENU SETTINGS Image Display Mode Presentation Bright Game Movie TV sRGB User User1 Brilliant Color 0 10 Brightness 0 100 Contrast 0 100 Sharpness 0 31 Gamma PC MAC Video Chart B amp W Advanced Color Space Auto RGB YCbCr YPbPr Color Temperature Cold Normal Warm Reset Computer Horizontal Position 5 5 Vertical Position 5 5 Frequency 0 3
9. Rubber Foot Pad Stability and maintain cooling ventilation Cooling Vent Do not cover Standard Accessories Along with the Qumi the following accessories are included Remote Control With one 3V CR2025 battery VGA Cable Regional Power Cord and Power Adapter Documentation Kit User Manual Quick Start Guide Warranty Card Cable Cores Standard HDMI Cable HO Da MHL cable Carrying Case Audio Video Cable Q5 WIFI Dongle for Q5 Series only Contact your dealer immediately if any items are missing appear damaged or if the unit does not work It is recommended that you keep the original packing material should you ever need to return the equipment for warranty service Note Accessories will vary from model to model To ensure a high quality performance from your projection and to prevent electromagnetic interference EMI equip the VGA or HDMI video source cable with the included cable cores Remote Control Up Cursor Navigate and change settings in the OSD Cursor navigation when using Web Browser ON OFF Turn on or off Qumi Left Cursor Navigate and change settings in the OSD Cursor navigation when using Web Browser Mouse Mouse left key when using the Web Browser Menu Open and exit the OSD Page Up Down Page up and down when using the Web Browser
10. button to select the Installation Il menu 3 Press the A or Y button to select the Advanced menu and then press zi 4 Press the A or Y button to move the cursor up or down in the Advanced menu 5 Press the lt or gt button to change values for each applicable setting Installation Il Advanced OSD Menu Setting Peripheral Test 3D Low Power Mode ITEM DESCRIPTION Press to enter the OSD setting menu See page 39 for more DM ES j information on OSD Menu Setting Peripheral Test esse to enter the Peripheral Test menu See page 39 for more information on Peripheral Test Press lt to enter the 3D menu See 3D on page 40 Press the lt or gt button to enable lt 1W power consumption or disable Low Power Mode Note Enable Low Power Mode to completely power down when the projector is turned off Disable Low Power Mode to allow multimedia functionality when the projector is turned olf Low Power Mode Note To use the 3D function the Play Movie in 3D setting found in your player under the 3D Disc Menu must be enabled 3D functionality works when the input source supports 120Hz 1 The 3D OSD menu item is gray if there is no appropriate 3D source This is the default setting 2 When the projector is connected to an appropriate 3D source the 3D OSD menu item is enabled for selection 3 Use 3D glasses to view a 3D image 4 You need 3D content from a 3D DVD or 3D media file 5 You need to enable the 3D source s
11. by moving the focus ring up or down until the image is clear Setting an Access Password Security Lock To prevent unauthorized use of the Qumi you can create a password When the access password function is enabled the password must be entered after the Qumi has been turned on Creating a password can be done by performing the following steps 1 Press the MENU button on Gesi the remote control or press A MENU and on the keypad Briliant Color simultaneously to open the On ee 50 Screen Display OSD menu Menu Exit Image Langu age p E Menu Select 4 gt Scroll a v 2 Move the cursor to the E eof S Computer Video Audio Insta ation Installation Il Installation tab and scroll down to select Advanced Menu Exit Item Adjust lt 4 3 Press the or Y button to i select Security Lock 4 Press the or gt button to enable or disable the security f ne lock function A password dialog box Menu Exit item Adjust 4 P Scroll a w automatically appears 5 You can use the A Y lt gt i e o buttons located either on top Register Pa of the Qumi or on the remote control to enter the password Any combination of the navigation buttons can be used five must be chosen Password Menu Exit Press the navigation buttons in a KS DA any order to set the password ci erg Then press the MENU button to malo Sa exit the dialog box
12. e MP3 up to 256Kbps bit rate e WMA MID MIDI MP1 MP2 OGG AAC AMR WAV AC3 M4A AWB APE Playing your Track To open the music list perform the following 1 Press the lt or gt button to select the Music icon in the media suite menu 2 Press amp to open the file directory 3 Select the folder containing the desired song 4 Press lt to play the desired song A song can be paused or can be played by selecting the Pause Play button in the music player interface When the cursor is selecting the progress bar a song can be paused or can be played by pressing lt Control Interface The music player interface contains the following controls Against all odds_192Kbps44 1KHz mp3 Ecg Kees ER Pe rss Se Reeg Em ey Se See SE Pe rn 00 29 03 21 The music player provides controls to navigate through a song playlist The following table provides a description the controls ACTION DESCRIPTION Ki SES I KS Toggle speaker output to Left Right Stereo Tau Return to previous Forward to next track F E Return to the previous menu The order of songs and playback mode can be adjusted The following table provides a description of the playback modes ACTION DESCRIPTION Songs in the playlist will play in a continuous order RR sereni Gawa ER mr The music player contains many preset equalizer settings that can be applied The following table provides a description of the different equalizer
13. from four projection methods J Front Rear Ceiling Front Ceiling Rear Aspect Ratio Press the lt or gt button to adjust the video aspect ratio Press the lt or gt button to adjust the display keystone Digital Zoom Press the lt or gt button to adjust the Digital Zoom menu Press lt to enter the Advanced menu See Advanced on page Advanced 36 Reset Press to reset all settings to default values expect Language and Security Lock 35 Advanced To adjust the advanced settings press lt to enter the Advanced sub menu Ci ed Ed Image Computer Video Audio Installation Installation Il Advanced Security Lock Keypad Lock Presentation Timer Auto Keystone Menu Exit Scroll w ITEM DESCRIPTION Press the or gt button to enable or disable security lock Security Lock function Keypad Lock Press the lt or gt button to enable or disable keypad lock function Presentation Timer Press lt to enter the Presentation menu Auto Keystone Press the lt or gt button to enable or disable automatic keystone Note Auto Keystone is only available in Q5 Series Presentation Timer To adjust the presentation timer settings press lt to enter the Presentation Timer sub menu Ie ER Image Computer Video Audio Installation Installation Il Advanced Presentation Timer Timer Timer Period Timer Reset Menu Exit Scroll 9 ITEM DESCRIPTION l Press the lt or
14. or gt button to adjust the color space Color Temperature Press the lt or gt button to adjust the color temperature 31 Computer Menu To access the Computer menu and adjust the settings perform the following steps 1 Enter the OSD menu 2 Press the lt or gt button to select the Computer menu 3 Press the A or W button to move the cursor up or down in the Computer menu 4 Press the lt or gt button to change values for each applicable setting Horizontal Position Vertical Position Frequency Tracking Auto Image ITEM DESCRIPTION Horizontai Position oak the lt or gt button to adjust the display position to left or Vertical Position Press the lt or gt button to adjust the display position to up or down Press the lt or gt button to adjust the A D sampling clock Press the lt or gt button to adjust the A D sampling dot Press to automatically adjustment for phase tracking size and Auto Image position Note Items in the Computer menu can only be modified when the Qumi is connected to a PC through a VGA cable Settings that are not enabled or that cannot be modified are gray in color 32 Video Audio Menu To access the Video Audio menu and adjust the settings perform the following steps 1 Enter the OSD menu 2 Press the lt or button to select the Video Audio menu 3 Press the A or Y button to move the cursor up and down in the Video Audio menu 4 Press the lt or gt but
15. the following types of documents e Microsoft Word 97 2007 doc docx e Microsoft PowerPoint 97 2007 ppt pptx e Microsoft Excel 97 2007 xls xISx Adobe PDF pdf e Text txt Selecting Your Document To open a file in document viewer perform the following 1 Press the or button to select the office viewer icon in the media suite menu 2 Press to open the file directory 3 Select the folder containing the desired file 4 Press to display the desired file Once a file is open press amp to zoom in for a larger view of the file Files can be zoomed in 2X 4X 8X and 16X views Use the navigation keys to move the view of the file To proceed to the next page or return to a previous page press the A or Y button Note You cannot move to the previous or next page if the view is zoomed in Control Interface The office viewer does not contain a dedicated control interface x Turning on Wifi Wifi When the optional Q5 WIFI USB Dongle is inserted you can surf the Web via Wi Fi by using the Web Browser To turn on Wifi perform the following 1 Press the or button to select the Wifi icon in the media suite menu 2 Press lt to enter Wifi Settings 3 Press the lt or gt button to select Enable and then press lt to turn on Wifi function 4 Press the or button to select and then press to search for APs 5 Press the A or W button to select an AP and then press to connect
16. trademarks Mobile High Definition ink OF registered trademarks of MHL licensing LLC All other product names used in this manual are the properties of their respective owners and are acknowledged Important Safety Information Important It is strongly recommended that you read this section carefully before using the Qumi These safety and usage instructions that will make sure you enjoy many years of safe use of the Qumi Keep this manual for future reference Symbols Used Warning symbols are used on the unit and in this manual to alert you of hazardous situations The following styles are used in this manual to alert you to important information Note Provides additional information on the topic at hand AN Important Provides additional information that should not be overlooked AN Caution Alerts you to situations that may damage the unit AN Warning Alerts you to situations that may damage the unit create a hazardous environment or cause personal injury Throughout this manual component parts and items in the OSD On Screen Display menus are denoted in bold font as in this example Press the Menu button on the remote control to open the Main menu General Safety Information Do not open the unit case There are no user serviceable parts in the unit For servicing contact qualified service personnel Follow all warnings and cautions in this manual and on the unit case The projection light so
17. types of media These devices can be connected to the Qumi by using an appropriate cable Make sure that the connecting device has an appropriate output connector Connect audio video devices Connect AC power adapter Connect HDMI MHL peripherals Connect audio Connect personal computers Insert USB device only devices available in Q5 Series ZN Warning As a safety precaution disconnect all power to the Qumi and connecting devices before making connections Setting Up Qumi Connecting Peripherals by HDMI Connect HDMI compatible peripherals to the Qumi by using an HDMI cable Optional Blue Ray Camera Smartphone DVD player AUDIO OUT AVIN age Peet Game Personal Console Computer Connecting to an MHL Device Connect your Qumi to a MHL compatible device by using an MHL cable Optional Smartphone Tablet Note For some MHL compatible devices whose output is not thru micro USB an extra cable adaptor may be required Connecting Personal Computers Connect a personal computer to the Qumi by using the VGA cable 7 AUDIO OUT AVIN Personal Computer Note The personal computer must have a VGA output port to use the VGA cable to connect to the Qumi Inserting a USB Drive Connect a USB drive to the Qumi by inserting the storage device s into the appropriate port N AUDIO OUT AVIN Note The feature is only available in Q5 Series
18. 1 Tracking 0 9 Auto Image Video Video AGC Off On Audio Video Saturation 0 100 Video Tint 0 100 Video Overscan Off On Closed Captioning Off On Audio Volume 0 8 Mute Off On Audio Input AV IN HDMI USB Reset 27 OSD Sub Menu Overview MAIN SUB MENU MENU SETTINGS Installation Language English Frangais Deutsch Espanol Portugu s GC HSC Ra x Italiano Norsk Svenska Nederlands Pyccxun Polski Suomi EAAnvikd toi Magyar Cestina tI T rk e Vi t HAASE mg sw yarn Blank Blank Red Green Blue Screen White Projection Front Real Ceiling Real Ceiling Aspect Ratio Fill 4 3 16 9 Letter Box Native 2 35 1 Keystone 40 40 Digital Zoom 10 10 Advanced Security Lock Off On Keypad Lock Off On Presentation Timer Off On Timer Timer Period 1 60 Timer Reset Auto Off On Keystone Note Auto Keystone is only available in Q5 Series 28 OSD Sub Menu Overview MAIN MENU SUB MENU SETTINGS Installation II Auto Source Off On Auto Power Off 0 180 min Auto Power On Off On LED Mode ECO Normal Advanced OSD Menu Menu Position Center Down Setting Up Left Right Translucent Menu 0 25 50 75 100 Menu Display 0 20 Peripheral Test Remote Control Test Color Test Button Test 3D 3D Off DLP Link IR 3D Sync Invert Off On Low Power Mode Off On Factory Reset Status Active Source Video Inform
19. Note 1 The Wifi function is only available with Q5 s optional dongle 2 Press Page Up on the remote control to return to the top of the function area From here you can refresh the AP list 3 Press Page Down to move to the bottom of the AP list when in the function area Control Interface The Wifi Setting contains the following controls be Disable Configure Connection status VMAXD60864 ci ROGER LM WLG640 3Com linksys DCDC Jetta Matt s iPhone ACTION DESCRIPTION 20 Web Browser Visiting a website 1 Plug the optional Q5 Wi Fi Dongle into Qumi s USB socket 2 Press A Y lt p onthe remote control to control the cursor See Remote Control on page 4 3 Use the remote control for navigation control Press the Q icon bottom right to access the address bar 4 Press to display the virtual keyboard or press in the address bar You Tube GC a THe Ba en BR Google FAX Mayday Hangouts PR 5 8 Take RPA 3599 RAR 2012 hito TAS ss Nets wan 2A FABER gt by GoogleTai from Spotlight Videc by ctitv from YouTube Trends 20120506F FARE _ hitomi TSS Top 5Plays Episode 5 ft Ocelote IPL 3 jS Triple T Good Night Official 20 League Of Legends music video by nagootv by IPLLoL by 3tang3 from Top Favorited from YouTube Trende from Top Favor Note Plug a USB hub into Qumi s USB socket then plug the optional Q5 Wi Fi dongle keyb
20. Qumi does not use a typical Qumi lamp It uses a set of Light Emitting Diodes LED to illuminate and project images LED s have a greater lifespan than conventional lamps Qumi LED s are estimated to last for approximately 30 000 hours The lifespan of the LED depends on factors such as brightness usage environmental conditions LED brightness can decrease over time The LED module is not replaceable 12 Why do I need to re adjust the focus on my Qumi after it s powered up For the best picture quality adjustment of the focus ring may be necessary once the operational temperature has been met Note Qumi media suite is not available in Q4 Series Vivitek Support Site Please visit www vivitekcorp com for more information support and product registration 46 Specifications PROJECTION SCREEN SIZE ire VERTICAL KEYSTONE CORRECTION PROJECTION METHODS Front Rear Desktop Front Ceiling Rear Ceiling DATA COMPATIBILITY VGA SVGA XGA SXGA SXGA UXGA Mac SDTV EDTV HDTV 480i 480p 720p 10801 1080p HDTV 720p 1080i p NTSC NTSC 4 43 PAL B G H I M N 60 SECAM FCC B UL CCC CE C Tick KC CB SASO NOM SEED SEINE EZ OL PCT RoHS ICES 003 Canada DIMENSIONS WXHXD 160mm d 3 x 102mm 4 03 x 32mm 1 27 INPUT TERMINALS Note For questions regarding product specifications please contact your local distributor USB Type A connector media suite is only available in Q5 Series 40 step
21. amount of water gets into the interior of the Qumi while cleaning unplug the Qumi and set in a well ventilated area for several hours before using 4 If a large amount of water gets into the interior of the Qumi when cleaning unplug the Qumi and have it serviced Cleaning the Lens Optical lens cleaning solutions can be purchased from most camera and other retail stores To clean the Qumi lens perform the following steps 1 Apply a small amount of the optic lens cleaning solution to a clean and soft cloth Do not apply the cleaning solution directly to the lens 2 Gently wipe the lens in a circular motion AN Caution 1 Do not use abrasive cleaners or solvents 2 To prevent discoloration or fading do not allow the cleaning solution to contact the Qumi case 42 Troubleshooting Common Problems and Solutions These guidelines provide tips to deal with problems you may encounter while using the Qumi If the problem remains unresolved contact your dealer for assistance The problem sometimes can be as simple as a wire that is not completely connected Review the following possible issues before proceeding to the problem specific solutions Use another electrical device to confirm that the electrical outlet is properly working Make sure that the Qumi is turned on e Make sure all connections are securely connected e Make sure that the connected device is turned on e Make sure that the connected PC is not in suspe
22. ation LED Hours Eco Normal 29 Image Menu To access the Image menu and adjust the settings perform the following steps 1 Enter the OSD menu 2 Press the lt or gt button to select the Image menu 3 Press the A or Y button to move the cursor up or down in the Image menu 4 Press the lt or gt button to change values for each applicable setting Display Mode Presentation Erilliant Color Brightness JU Contrast 50 Sharpness 16 Gamma PC Advanced eo Reset Uni ITEM DESCRIPTION Press the or gt button to adjust the gamma correction of the Panna display Press to enter the Advanced menu See Advanced Feature on page 31 Reset Press lt to reset all settings to default values Note The Brilliant Color Brightness Contrast Sharpness Gamma and Advanced settings are adjustable only when the Display Mode is set to User and User Advanced 30 Advanced Feature To access the Advanced menu and adjust the settings perform the following steps 1 Enter the OSD menu Press the lt or gt button to select the Image menu 2 3 Press the A or Y button to move to the Advanced menu and then press lt 4 Press the A or Y button to move the cursor up or down in the Advanced menu Wu wl H Image Computer Video Audio Installation Installation Il W Advanced Color Space Auto Color Temperature Normal Menu Exit Scroll w ITEM DESCRIPTION Color Space Press the lt
23. e Allow Qumi to cool down before storing in a compartment Regulatory Warnings Before installing and using the Qumi read the regulatory notices in the Regulatory Compliance on page 51 Symbol Explanations DISPOSAL Do not use household or municipal waste collection services for disposal of electrical and electronic equipment EU countries require the use of separate recycling collection services Main Features Lightweight unit easy to pack away and transport Compatible with all major video standards including NTSC PAL and SECAM A high brightness rating allows for presentations in daylight or in lit rooms Supports data resolution up to UXGA at 16 7 million colors to deliver crisp clear images Flexible setup allows for front rear ceiling and rear ceiling projections Line of vision projections remain square with advanced keystone correction for angled projections Input source automatically detected About this manual This manual is intended for end users and describes how to install and operate the Qumi Wherever possible relevant information such as an illustration and its description has been kept on one page This printer friendly format is both for your convenience and to help save paper thereby protecting the environment It is suggested that you only print sections that are relevant to your needs Table of Contents PIACE A A E EE A EA EN E A ETE E E li Chapter 1 At a Glance re eee ce eee en
24. e eee eee 1 OY SUSY u E E E n 1 Standard Accessories a 3 Optional Accessories a ra rr ss s 3 Pelo 6 CON u no ia 4 Qumi and Remote Control Buttons a 4 Media EA Ve EE 5 Chapter 2 Getting Started 6 WIN Lr 6 Setting Up Qumi a a a 7 Setting Up the ue ni ususskusakaqasusshuqayaquqaqunuma iss 13 Chapter 3 Qumi Media Suite 14 ENEE eegener 14 VU 15 Ville Vu 17 Eine ie GE 18 OMICS VICWEF EE 19 Eegen ZU WET e EE 21 ORT ie io ina 22 SEET 23 Chapter 4 On Screen Display OSD Settings 25 SORTIE 25 Setting the OSD Language iii 26 OSD Menu Over EW sessa u u u u uuu ukasa 27 imade E uu u irene aasawa qasanan en 30 ei let El EE 32 Mile O Ee e RT LU EE 33 Installation MENU a a aa raararrarrs a 35 Installation Il MENU 37 Chapter 5 Taking Care of Your Qumi 42 2 q eski s i eege 42 EE elef TS E 42 Be ellen ele le e EE 43 Vivitek Support Site II e iea E ENEE E Enie ENN ES 46 let erte le KC 47 Projection Distance vs Projection SIZE 48 Projection Distance and Size Table 0nn00nn0nnnannnnnnennunnnnnnnrnnnrnrrrnnrnnrnnrrnnrrn
25. if a cable box is used it can be connected by an HDMI cable to the Qumi How can MHL connect to the Qumi Use support MHL cable to connect MHL device Please visit www mh consortium org productlist for more information 45 5 Howare images from a digital camera or a USB storage device displayed Images and other content can be displayed by connecting the following devices to the Qumi e USB flash drive hard drive card reader e Digital camera Smart phone e Multimedia storage viewer Once the devices are connected images can be displayed by using the Qumi Media Suite 6 Which cable is required to video devices to the Qumi Video devices can be connected to the Qumi by using an Audio Video or HDMI MHL cable if the devices contain the appropriate ports To play audio a separate stereo mini jack adapter cable 3 5mm mini plug and two RCA plugs An RCA cable connected can also be connected to the Qumi 7 What type of video formats does the Qumi support H 264 MPEG 4 VC 1 WMV9 DivX Xvid Real Video AVS and MJPEG 8 What type of audio formats does the Qumi support MP3 and WMA 9 What type of document formats does the QUMI support Microsoft Office 2003 and Microsoft Office 2007 Word Excel PowerPoint Adobe PDF and text files txt 10 What type of photo formats does the QUMI support JPEG PNG and BMP 11 How long will the LED light source in the Qumi last and can it be replaced The
26. nd or sleep mode e Make sure the connected notebook computer is properly configured for an external display Tips for Troubleshooting In each problem specific section perform the steps in the order suggested Doing so may help solve the problem more quickly In order to avoid replacing non defective parts try to find and isolate the problem For example if you replace batteries and the problem remains put the original batteries back and move to the next step Keep a record of the steps you take when troubleshooting The information may be useful for reference when calling technical support or for bringing the Qumi to service personnel LED Error Messages LEFT KEY RIGHT KEY ERROR CODE MESSAGES SIERRA BLUE BLINK Over temperature error Inletair 3 OFF LED over temperature Red J 3 Z Jo 1 LED over temperature Green 3 Z J 2 LED over temperature Blue 3 J 3 GOO I N Fan 1 oer eg 6 1 Fan 2 System eng BL Red LED Thermistor omg J BL li Green LED Thermistorerror 2 Blue LED Thermistor error 3 In the event of an LED error disconnect the AC power cord and wait for one 1 minute before restarting the Qumi N N LA If there is any other situation that isn t listed in the chart above please contact your service center 43 Image Problems Problem No image appears on the screen 1 Verify that the settings on your personal computer are properly configured 2 Tur
27. noffall of the equipment and power up the equipment again in the correct order Problem The image is blurred 1 Adjustthe Focuson the Qumi 2 Make sure the Qumi to screen distance is within the specified range 3 Clean the Qumi lens with optical lens cleaning cloth if it is dirty Problem The image is wider at the top or bottom trapezoid effect 1 Position the Qumi so that it is perpendicular to the screen as much as possible 2 Adjust the Keystone settings in the OSD to correct the problem or set Auto Keystone to On Note Auto Keystone is only available in Q5 Series Problem The image is reversed Check the orientation of the Projection setting in the Installation menu in the OSD Problem The image is streaked 1 Set the Frequency and Tracking settings on the Computer menu in the OSD to the default settings 2 Connectthe Qumi to another computer to make sure that the problem is not caused by a computer s video card Problem The image is flat with no contrast Adjust the Contrast setting in the Image menu in the OSD Problem The color of the projected image does not match the source image Adjust the Color Temperature and Gamma settings in the Image menu in the OSD Remote Control Problems Problem The Qumi does not respond to the remote control 1 Aim the remote control towards remote sensor on the Qumi Make sure the path between remote and sensor is not obstructed Turn off any fluorescent lights in the room
28. ntrol the media functions with the remote control please refer to 14 Media Player Screen The media player screen is the main interface for the Qumi Q5 Series If a USB drive is plugged in when powering on the Qumi the media player screen appears In the media player screen you can choose the type of media to display by selecting Music A music player that supports many types of audio files ready to play music Movie An easy to use movie player that displays multiple movie formats Photo A photo viewer that contains slide show functionality Office Viewer A document viewer that displays documents Wifi Display Use this to configure the connection to a wireless access point Web Browser A Web Browser for surfing the Internet Wifi Use this to choose a Wi Fi access point Settings The settings of the Qumi can be adjusted in this menu Note Wifi amp WebBrowser functions are only available with Q5 s optional dongle Qumi media suite is only available in Q5 Series Chapter 2 Getting Started What You Need Many types of external devices and peripherals can be connected to the Qumi External or portable music players can be connected to play music DVD VCD and VHS players can be connected to play movies Camcorders and digital cameras can also be used to play videos and display photos Computers can be connected as well as peripherals such as USB drives to display documents and other
29. nvert On or Off Factory Reset To reset all of the menu items to the factory default values except Language and Security Lock perform the following steps 1 Press the A or Y button to move the cursor up or down in the Installation Il menu 2 Select the Factory Reset sub menu 3 Press lt Menu Exit Item Adjust H Scroll 40 Status To see the status of the Qumi perform the following steps 1 Press the A or Y button to move the cursor up or down in the Installation Il menu 2 Select the Installation Il sub menu 3 Press lt to enter the Status sub menu Dio Image Computer Video Audio Installation nstallation Il Active Source Analog RGB Video Information 1024 x 768 860 Hz LED Hours Eco Normal O O ITEM DESCRIPTION Active Source Displays the activated source l Displays resolution video information for RGB source and color Video Information i standard for Video source LED Hours LED use information is displayed in hours Eco and Normal counters are separated 41 Chapter 5 Taking Care of Your Qumi Cleaning the Qumi Cleaning the Qumi to remove dust and grime will help provide trouble free operation AN Warning 1 The Qumi should be turned off and unplugged before cleaning Failure to do so may result in injury or damage to the system 2 Use only a dampened cloth when cleaning Do not allow water to enter the ventilation openings on the Qumi 3 If a small
30. oard and mouse into the USB hub to surf the Internet easily Control Interface The Main bar contains the following controls ACTION DESCRIPTION x nem ene ee seem Add Delete current page to bookmark Click to enter URL input page Clear History and Exit browser 21 Wifi Display Ll Control Interface The Wifi Display contains the following controls Wifi Display Link mode Wireless WiFi IP setting Use default IP Use other IP IP address k d _ _ _r Gateway DNS ACTION DESCRIPTION Use Other IP to manually configure IP settings Note Wifi amp Web Browser functions are only available with Q5 s optional dongle 22 Settings S System Options The system options menu displays the system and firmware information The Information menu provides details about the software version Play Mode The play mode menu displays settings for both video and music player options The following settings are available e Repeat None The videos or music tracks will not repeat after it is completed Shuffle The order of videos or music tracks will play in a random order e Repeat One A selected video or music track will continuously repeat after it is completed e Repeat All All videos or music tracks in a playlist will repeat after all of the files in the playlist have been completed Note The Qumi media suite always supplies an output of 1280x800 resolution
31. ome 3D DVD content may have a 3D on off selection feature 6 You need DLP link 3D or IR 3D shutter glasses With IR 3D shutter glasses you need to install a driver on your PC and connect a USB emitter 7 The 3D mode of the OSD needs to match the type of glasses DLP link or IR 3D 8 Power on the glasses Glasses normally have a power on off switch Each type of glasses has their own configuration instructions Please follow the configuration instructions that come with your glasses to finish the setup process 38 OSD Menu Setting Menu Position Translucent Menu Menu Display Scroll e ITEM DESCRIPTION Menu Position Press the lt or gt button to select different OSD location Press the lt or gt button to select OSD background translucent Translucent Menu level Menu Display Press the lt or gt button to select OSD timeout delay Peripheral Test Co Ce e Ed Ea Image Computer Video Audio Installation Installation Il Advanced Peripheral Test Remote Control Test Color Test Button Test Menu Exit Scroll w ITEM DESCRIPTION Remote Control Test Press to test the IR remote controller for diagnostic Color Test Press to select different colors on screen Button Test Press to test the button on keypad 39 Menu Exit Scroll w ITEM DESCRIPTION Press the lt or gt button to select Off DLP Link or IR 3D Sync Invert Press the lt or gt button to turn 3D Sync I
32. renne 48 Timing Mode Table ornella 49 Qumi Bing E e EE 50 Regulatory Compliance iii 51 Safety Ee deel EE 51 DISD OS Al and Recycling ME 51 Chapter 1 At a Glance Overview Front Top Right View Keypad See Keypad On Screen Display OSD buttons Cooling Vent Do not cover Cooling Vent Lens Do not cover Projection Lens Focus ring Focus the projected image Keypad en Open and exit the OSD buttons Up Cursor _ _ ______y N Navigate and change settings in the OSD Enter Cursor Change settings in the OSD Left Cursor lt gt Right Cursor Navigate and change settings Navigate and change settings in the OSD inthe OSD Down Cursor Y Navigate and change settings in the OSD Rear Top Left View Connect the supplied power adapter Audio Out Connect an audio cable to speakers or headphones AV In A Power Switch Turn on off the Qumi Universal I O Connect the AV IN cable from a l Connect a RGB or component video device I USB cable from a device HDMI MHL Connect an USB drive Connect a HDMI MHL cable from a HDMI MHL device IR Receiver Receive IR signal from the remote control Bottom View Docking Connector Only Available in Q5 Series Dock to optional battery pack Remove the sticker before use Tripod Connecting Slot Only Available in Q5 Series Tripod not included Remove the sticker before use
33. s 45 33 VIDEO COMPATIBILITY 47 Projection Distance vs Projection Size Image Height Keystone Correction Angle IMAGE IMAGE PROJECTION IMAGE HIGH OFFSET A DIAGONAL WIDTH DISTANCE CM INCHES CM INCHES cM INCHES CM INCHES cWiNcHES 48 Timing Mode Table H SYNC V SYNC COMPOSITE DVI SIGNAL RESOLUTION wu HZ S vibeo COMPONENT RGB ou NTSC 15 734 60 0 PAL SECAM 15 625 50 0 720 x 400 85 0 800 x 600 800 x 60 72 0 800 x 60 75 0 640 x 48 85 0 800 x 60 56 0 800 x 60 800 x 60 72 0 800 x 60 75 0 800 x 60 85 0 1024 x 768 1024 x 768 70 0 1024 x 768 60 0 _ 1024 x 768 85 0 1280 x 80 59 8 1280 x 800 74 9 1280 x 800 84 8 1280 x 1024 1280 x 1024 75 0 1280x960 60 0 1280 x 960 85 S O O S O O O lt m o gt N O1 ae 1400 x 1050 1440 x 900 7 1440 x 900 5 5 640 x 480 66 6 Apple Mac 832x624 49725 74 55 PP 1024x 768 60 24 75 0 0 5 6 1152 x 870 68 68 19 SDTV 480i 15 734 576i 15 625 50 0 0 0 SE 480p 31 469 576p 31 25 50 0 720p 50 0 720p nn 10801 10801 50 1080p 1080p 50 O Frequency supported Frequency not supported Displayable level cO Qumi Dimensions 160mm 6 3 102mm 4 03 ke 160mm 6 3 ZA PI I gt
34. settings ACTION DESCRIPTION Normal Classical Jazz Movies Supported Formats The following video formats are supported e H 264 video up to 720p at 30 frames per second Main Profile level 3 1 with AAC LC audio up to 160 Kbps 48kHz stereo audio in m4v mp4 and mov file formats e MPEG 4 video up to 2 5 Mbps 640 by 480 pixels at 30 frames per second Simple Profile with AAC LC audio up to 160 Kbps per channel 48kHz stereo audio in m4v mp4 and mov file formats e Motion JPEG M JPEG up to 35 Mbps 1280 by 720 pixels 30 frames per second audio in U Law PCM stereo audio in avi files Watching Your Movie To open a list of movies perform the following 1 Press the or button to select the Movie icon in the media suite menu 2 Press amp to open the file directory 3 Selectthe folder containing the desired movie file 4 Press to play the desired movie file While a movie is playing the control interface can be hidden To hide the control interface press the A button Press the A button again to show the control interface The control interface will automatically disappear if there is no user input for 5 seconds Control Interface The following playback functions are controlled by the remote control which are shown in the table below ACTION DESCRIPTION Pause Resume Press lt to pause or resume a movie Forward speed Press the lt or gt key to change the speed 2X 4X 8X
35. ssion to control the Qumi It is not necessary to point the remote directly at the Qumi The remote control functions properly within a radius of approximately 7 meters 23 feet and 15 degrees above or below the Qumi level if the remote is not held perpendicular to the sides or rear of the Qumi If the Qumi is unresponsive to the remote control move closer towards the Qumi Chapter 3 Qumi Media Suite Overview The Qumi Media Suite is designed to provide easy access to your files from an inserted USB drive Music movies pictures and documents can be displayed The media suite menu contains 8 applications that can be accessed De e Music A music player that supports many types of audio files ready to play music e Movie An easy to use movie player that displays multiple movie formats Photo A photo viewer that contains slide show functionality G4 e Office Viewer A document viewer that displays documents Ll Wifi Display Use this to configure the connection to a wireless access point Web Browser A Web Browser for surfing the Internet e Wifi Use this to choose a Wi Fi access point A e Settings The settings of the Qumi can be adjusted in this menu Note Wifi amp Web Browser functions are only available with Q5 s optional dongle Qumi media suite is only available in Q5 Series Music De Supported Formats The music player can play music files in the following formats
36. to the system so the OSD displays a resolution of 1280x800 as its received signal This does not indicate the actual resolution of the actual multimedia files USB Options The USB Mass Storage option allows you to connect a personal computer with a supported USB cable to transfer files between the Qumi and personal computer Note The Qumi media suite only supports input from USB drives 23 AutoPlay Option Use the AutoPlay Option menu to configure what the Qumi automatically plays when powered on The following settings are available when AutoPlay is ON e AutoPlay Turn on or off auto play e AutoPlay Type Automatically play photo or video files when powered on File Path Automatically play files in the root of USB or local memory To use AutoPlay on Qumi 1 Connect PC to Qumi using a USB cable 2 Move media files to respective folder Movies for movie files or Photos for image files To use AutoPlay on USB device 1 Create Movies or Photos folder in USB drive 2 Copy media files to respective folder Movies for movie files or Photos for image files 3 Remove USB drive and insert in Qumi Note 1 AutoPlay files on USB drive must be named Movies or Photos for this function to play media files 2 Built in memory for Qumi Q5 is 4GB 24 Chapter 4 On Screen Display OSD Settings OSD Menu Controls The Qumi has an On Screen Display OSD settings menu that allows you to make adjustmen
37. ton to change values for each applicable setting Video AGC Video Saturation Video Tint Video Overscan Closed Captioning Audio Reset ITEM DESCRIPTION Control for video source Note Video AGC Video Saturation Video Tint and Closed Caption settings are adjustable only when the source is from composite video The Video Overscan settings are adjustable only when the source is from composite component and HDMI video 33 Audio To adjust the audio settings press lt to enter the Audio sub menu udio Installation Menu Exit scroll a w ITEM DESCRIPTION Press the or gt button to adjust the audio volume Press the or gt button to turn on or off the speaker Press the lt or gt button to select audio input 34 Installation Menu To access the Installation menu and adjust the settings perform the following steps 1 Enter the OSD menu 2 Press the or gt button to select the Installation menu 3 Press the A or Y button to move the cursor up or down in the Installation menu 4 Press the lt or gt button to change values for each applicable setting Language Blank Screen Projection Aspect Ratio Keystone Digital Zoom Advanced Reset ITEM DESCRIPTION Press the lt or gt button to select a different localization menu Press the lt or gt button to select different color to blank the Blank Screen screen Proiecion Press the or gt button to choose
38. ts and changes to settings such as display settings and audio settings There are 5 menus within the OSD menu Image Various aspects of the image quality can be adjusted in this menu e Computer Settings for personal computers can be adjusted in this menu Video Audio Many settings for video and audio can be adjusted in this menu e Installation Default language and other settings can be adjusted in this menu e Installation Il Factory reset and other settings can be adjusted in this menu If the interface is set on AV IN HDMI MHL or Universal I O the OSD menu can be accessed by pressing the MENU button on the remote control or keypad If the interface is set on the Qumi Media Suite menu the OSD menu can be accessed by pressing the MENU button on the remote control or by simultaneously pressing MENU and lt on the keypad Note If the OSD menu is inactive for 15 seconds the OSD menu will close Navigating the OSD The remote control cursor buttons or the buttons on the top of the Qumi can be used to navigate and make changes to the OSD settings 1 Enter the OSD menu 2 Press the lt or gt button to move through the 5 menus Display Mode Presentation Brilliant Color 3 Pressthe or Y Brightness 50 button to move the Contrast 50 cursor up and down Sharpness 16 within in a menu Gamma da Advanced E 4 Press lt or gt to Rosst Ge change the values for specific settings 5 Press
39. urce is extremely bright by design To avoid damage to eyes do not look into the lens when the LED illumination is on Do not place the unit on an unstable surface or stand Avoid using the system near water in direct sunlight or near a heating device Do not place heavy objects such as books or bags on the unit Qumi Installation Notice e Allow at least a 50cm clearance around the exhaust vent Minimum 100mm H Minimum 500mm e Make sure that the intake vents do not recycle hot air from the exhaust vent e When operating the Qumi in an enclosed space make sure that the surrounding air temperature within the enclosure does not exceed operating temperature while the Qumi is running and the air intake and exhaust vents are unobstructed All enclosures should pass a certified thermal evaluation to make sure that the Qumi does not recycle exhaust air as this may cause the device to shutdown even if the enclosure temperature is with the acceptable operating temperature range AN Caution Avoid using the Qumi in dusty environments Power Safety e Only use the supplied adapter e Do not place anything on the cord Place the cord where it will not be in the way of foot traffic Remove the battery from the remote control when storing or not in use for a prolonged period Cleaning the Qumi e Unplug the cord before cleaning See Cleaning the Qumi on page 42 Note The Qumi will be warm after usag
40. vivitek QUMI Q5 Q4 Series User Manual RP m FAPFH Manual del usuario Manuel de l utilisateur Benutzerhandbuch MESXM SSA PykKOBOACTBO NONb30BaTeNnA Gebruikershandleiding Instrukcja obstugi Uzivatelska prirucka Evygipidio Xpnong Kullanim Kilavuzu Manuale d uso Handbok Brugervejledning Brukerveiledning K ytt ohje Felhaszn l i k zik nyv Aal aoit Manual do Usu rio az Sekt Dd Preface Copyright 2014 Vivitek VIVI tek is a trademark of DELTA Corporation Other trademarks are the properties of their respective owners Values weights and dimensions are approximate Specifications are subject to change without prior notice Disclaimer The information in this document is subject to change without notice The manufacturer makes no representations or warranties with respect to the contents hereof and specifically disclaims any implied warranties of merchantability or fitness for any particular purpose The manufacturer reserves the right to revise this publication and to make changes from time to time in the content hereof without obligation of the manufacturer to notify any person of such revision or changes Trademark Recognition HOTTII HDMI the HDMI Logo and High Definition Multimedia Interface are NIGH DEFINITION MULTIMEDIA renrace trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries IMI LA MHL the MHL logo and Mobile High Definition Link are
Download Pdf Manuals
Related Search