LNP-1002G-SFP Series
Contents
1. Rail on to the track as shown below in Figure 3 2 Insert the Switch on the DIN Rail 4 Lightly pull down the bracket on to the rail as shown below in Figure 3 3 Stable the Switch on DIN Rail 5 Check if the bracket is mounted tightly on the rail 6 To remove the industrial Ethernet switch from the rail do the opposite from the above steps 13 Antaira Industrial Ethernet Switches LNP 1002G SFP Series User Manual V1 0 3 2 Wall Mounting Follow the steps below to mount the industrial Ethernet switch using the wall mounting bracket as shown below in Figure 3 4 l 2 3 4 Remove the DIN Rail bracket from the industrial Ethernet switch by loosening the screws Place the wall mounting brackets on the top and bottom of the industrial Ethernet switch Use the screws to screw the wall mounting bracket on the industrial Ethernet switch Use the hook holes at the corners of the wall mounting bracket to hang the industrial Ethernet switch on the wall To remove the wall mount bracket do the opposite from the steps above Figure 3 4 Remove DIN Rail Bracket from the Switch Below in Figure 3 5 are the dimensions of the wall mounting bracket Figure 3 5 Wall Mounting Bracket Dimensions 14 Antaira Industrial Ethernet Switches LNP 1002G SFP Series User Manual V1 0 4 Hardware Installation 4 1 Installation Steps This section will explain how to install Antaira s LNP 1002G SFP series 10 port2. 2 11 Figure 2 11 LC Connector to the Transceiver Antaira Industrial Ethernet Switches LNP 1002G SFP Series User Manual V1 0 To remove the LC connector from the transceiver please follow the steps shown below 1 Press the upper side of the LC connector from the transceiver and pull it out to release as shown below in Figure 2 12 Figure 2 12 Remove LC Connector 2 Push down the metal clasp and pull the transceiver out by the plastic part as shown below in Figure 2 13 kbs 3 Figure 2 13 Pull Out from the SFP Module Antaira Industrial Ethernet Switches LNP 1002G SFP Series User Manual V1 0 2 Wiring the Power Inputs Please follow below steps to insert the power wire 1 Insert the positive and negative wires into the PWR1 V1 V1 and PWR2 V2 V2 contacts on the terminal block connector as shown below in Figure 2 14 V1 V1 V2 V2 Figure 2 14 Power Terminal Block 2 Tighten the wire clamp screws to prevent the wires from loosening as shown below in Figure 2 10 Figure 2 15 Power Terminal Block Note e Only use copper conductors 60 75 C tighten to 5 Ibs The wire gauge for the terminal block should range between 18 20 AWG Antaira Industrial Ethernet Switches LNP 1002G SFP Series User Manual V1 0 2 8 Wiring the Fault Alarm Contact The fault alarm contact is in the middle of the terminal block connector as the picture shows below in Figure 2 16 By inserting the
3. Antaira Industrial Ethernet Switches LNP 1002G SFP Series User Manual V1 0 5 Network Application This segment provides an example of an industrial Ethernet switch application Figure 5 1 Core Upper Level Switch Fiber Cable we o VOIP Phone IP Camera Wireless AP IEEE 802 3af at Compliant PD Powered Devices Figure 5 1 Industrial Ethernet Switch Application Reference 16 Antaira Industrial Ethernet Switches LNP 1002G SFP Series User Manual V1 0 6 Trouble Shooting Verify you have the right power cord or adapter Never use a power supply or adapter with a non compliant DC output voltage or it will burn the equipment e Select the proper UTP or STP cable in order to construct the network Use an unshielded twisted pair UTP or shield twisted pair STP cable for RJ 45 connections 1000 Category 5e for 10M 100Mbps Also be sure that the length of any twisted pair connection does not exceed 100 meters 328 feet Diagnosing LED Indicators To assist in identifying problems the switch can be easily monitored with the LED indicators which help to identity if any problems exist o Please refer to the LED Indicators section for LED light indication If the power indicator LED does not turn on when the power cord is plugged in the user may have a problem with the power cord Check for loose power connections power losses or surges at the power outlet o Please contact Antaira for technical supp
4. NCAIrA LNP 1002G SFP Series 10 Port Industrial PoE Gigabit Unmanaged Ethernet Switches 8 10 100 1000Tx 30W Port 2 100 1000 SFP Slot User Manual Version 1 0 Antara www antaira com Antaira Industrial Ethernet Switches LNP 1002G SFP Series User Manual V1 0 Copyright 2014 Antaira Technologies LLC All Rights Reserved This document contains information which is protected by copyright Reproduction adaptation or translation without prior permission is prohibited except as allowed under the copyright laws Trademark Information Antaira is a registered trademark of Antaira Technologies LLC Microsoft Windows and the Windows logo are the trademarks of Microsoft Corp NetWare is the registered trademark of Novell Inc WMM and WPA are the registered trademarks of Wi Fi Alliance All other brand and product names are trademarks or registered trademarks of their respective owners Notice Copyrights 2014 by Antaira Technologies LLC All rights reserved Reproduction adaptation or translation without prior permission of Antaira Technologies LLC is prohibited except as allowed under the copyright laws Disclaimer Antaira Technologies LLC provides this manual without warranty of any kind expressed or implied including but not limited to the implied warranties of merchantability and fitness for a particular purpose Antaira Technologies LLC may make improvements and or changes to the product and or speci
5. industrial PoE gigabit unmanaged Ethernet switch with 8 10 100 1000Tx 30W Port and 2 100 1000 SFP slots Installation Steps 1 2 Unpack the industrial Ethernet switch from the original packing box Check if the DIN Rail bracket is screwed on the industrial Ethernet switch e If the DIN Rail is not screwed on the industrial Ethernet switch please refer to the DIN Rail Mounting section for DIN Rail installation e If you want to wall mount the industrial Ethernet switch please refer to the Wall Mounting section for wall mounting installation To hang the industrial Ethernet switch on a DIN Rail or wall please refer to the Mounting Installation section Power on the industrial Ethernet switch and then the power LED light will turn on e If you need help on how to wire power please refer to the Wiring the Power Inputs section e Please refer to the LED Indicators section for LED light indication Prepare the twisted pair straight through category 5 cable for Ethernet connection Insert one side of the RJ 45 cable into switch s Ethernet port and on the other side into the networking device s Ethernet port e g switch PC or server The Ethernet port s RJ 45 LED on the industrial Ethernet switch will turn on when the cable is connected to the networking device e Please refer to the LED Indicators section for LED light indication When all connections are set and the LED lights all show normal the installation is complete 15
6. operating temperature range of 10 to 70 C and the other one with an extended operating temperature range of 40 to 75 Itisa perfectly designed product to fulfill any special needs for industrial automation outdoor applications and harsh weather environments 1 1 Key Features mM System Interface Performance All RJ 45 ports support auto MDI MDI X function Embedded 8 10 100 1000Tx PSE 30W Port and 2 100 1000 SFP slots Store and forward switching architecture 8K MAC address table Jumbo frame supports 9 6K Power line EFT protection 2 000VDC Ethernet ESD protection 6 000VDC mM Power Input DC 48 55V redundant power E Operating Temperature Standard operating temperature model 10 C 70 C Extended operating temperature model T 40 C 75 C Case Installation IP 30 protection Installation in pollution degree to environment DIN Rail and wall mount design Antaira Industrial Ethernet Switches LNP 1002G SFP Series User Manual V1 0 1 2 Package Contents M 1 LNP 1002G SFP T 10 port industrial PoE gigabit unmanaged Ethernet switch with 8 10 100 1000Tx 30W Port and 2 100 1000 SFP slots 1 User manual 1 Product CD 2 Wall mounting brackets and screws 1 DC cable 18 AWG amp DC jack 5 5x2 1mm 1 3 Safety Precaution Attention If the DC voltage is supplied by an external circuit please use a protection device on the power supply input The indust
7. wires it will detect the fault status including power failure or port link failure managed industrial switch only and form a normally open circuit An application example for the fault alarm contact is shown below in Figure 2 16 PWR1 Ti PWR2 24V de 1A Resistance Insert the wires into the fault alarm contact No 3 amp 4 Figure 2 16 Wiring the Fault Alarm Contact Note The wire gauge for the terminal block should range between 12 24 AWG e If only using one power source jumper Pin 1 to Pin 5 and Pin 2 to Pin 6 to eliminate power fault alarm Antaira Industrial Ethernet Switches LNP 1002G SFP Series User Manual V1 0 3 Mounting Installation 3 1 DIN Rail Mounting The DIN Rail is pre installed on the industrial Ethernet switch from the factory If the DIN Rail is not on the industrial Ethernet switch please see Figure 3 1 to learn how to install the DIN Rail on the switch Rear Panel ofthe switch DIN Rail Figure 3 1 The Rear Side of the Switch and DIN Rail Bracket 12 Antaira Industrial Ethernet Switches LNP 1002G SFP Series User Manual V1 0 Follow the steps below to learn how to hang the industrial Ethernet switch 1 Use the screws to install the DIN Rail bracket on the rear side of the industrial Ethernet switch To remove the DIN Rail bracket do the opposite from step 1 After the DIN Rail bracket is installed on the rear side of the switch insert the top of the DIN
8. 100BaseTX 2 pair UTP STP Cat 5 cable EIA TIA 568 100 ohm 100m 1000BaseT X UTP STP Cat 5 5E cable Antaira Industrial Ethernet Switches LNP 1002G SFP Series User Manual V1 0 Over Current Protection Single blown fuse Redundant power DC 48 55V with connective Power Input 1 6 pin removable terminal block 1 Relay output 210 Watis 48V 250 Watts 51 55V Max Power Consumption Full Load with PoE Function Installation DIN Rail mounting wall mounting optional Standard 10 C to 70 C 14 to 158 F Operating Temperature n g EOT 40 C to 75 C 40 to 167 F Operating Humidity 5 to 95 Non Condensing Storage Temperature 40 C to 85 C 40 F 185 F Lic n a FCC Class A CE EN61000 4 2 3 4 5 6 8 1 1 12 CE EN61000 6 2 CE EN61000 6 4 IEC60068 2 32 Free fall Stability Testing IEC60068 2 27 Shock IEC60068 2 6 Vibration Table 7 1 LNP 1002G SFP Series Technical Specification Antaira Customer Service and Support Antaira US Headquarter 844 268 2472 Antaira Europe Office 48 22 862 88 81 Antaira Asia Office 886 2 2218 9733 Please report any problems to Antaira www antaira com support antaira com www antaira eu info antaira eu www antaira com tw info antaira com tw 19
9. 2 2 Table 2 2 RJ45 Pin Assignments and signs represent the polarity of the wires that make up each wire pair All ports on this industrial Ethernet switch support automatic MDI MDI X operation Users can use straight through cables see figure below for all network connections to PCs servers other switches or hubs With straight through cable pins 1 2 3 and 6 at one end of the cable are connected straight through to pins 1 2 3 and 6 at the other end of the cable The table below Table 2 3 shows the 10BASE T 100BASE TX 1000BASE TX MDI and MDI X port pin outs Signal Name MDI Signal Name Receive Data plus RD Transmit Data plus TD Receive Data minus RD Transmit Data minus TD Transmit Data plus TD Receive Data plus RD Transmit Data minus TD Receive Data minus RD Table 2 3 Ethernet Signal Pin Outs The following figures show the cabling schematics for straight through and crossover Switch Router or PC Switch Switch 3 TD 3 RD 3 TD 3 TD 6 TD gt 6 RD 6 TD 6 TD L Mie H 1 RDH 1 RD 2 RD 2 TD 2 RD 2 RD Figure 2 4 Figure 2 5 Straight Through Cable Schematic Crossover Cable Schematic Antaira Industrial Ethernet Switches LNP 1002G SFP Series User Manual V1 0 The following figures show the 10 100 and 1000 Ethernet RJ 45 pin outs Pin Labe 12345678 1 TPos T Pt TPi TP TF2 TF1 TPs T
10. PJ b ci ho a i amp hi igure 2 RJ45 Ethernet Port Pin Outs Switch Router or PC Switch Switch 1 TPO lt 1 TPi4 1 TPO TPO 2 TPO lt 2 TPI gt TPO TPO 3 TP a 3 TPO4 TPi TPi 6 TFI gt 6 TPO G TP1 TPi 4 TPe e 4 TPJ 4 TP24 TP2 7 TP e 7 TP TP TP3 amp TP3 TP2 a TP3 TP3 Straight through cables schematic igure 2 7 Straight Through Cable Schematic 2 6 Cabling Use the four twisted pair category 5e or the above cabling for RJ 45 port connections The cable between the switch and the link partner switch hub workstation etc must be less than 100 meters 328 ft long Cross over cables schematic Crossover Cable Schematic The small form factor pluggable SFP is a compact optical transceiver used in optical communications for both telecommunication and data communication applications Antaira Industrial Ethernet Switches LNP 1002G SFP Series User Manual V1 0 To connect the transceiver and LC cable please follow the steps below First insert the SFP transceiver module into the SFP slot as shown below in Figure 2 9 Notice that the triangle mark is at the bottom of the SFP slot Figure 2 10 shows SFP transceiver module was inserted Triangle Mark Figure 2 9 Transceiver to the SFP Module Figure 2 10 Transceiver Inserted second insert the fiber cable of the LC connector into the transceiver as shown below in Figure
11. eseees 10 2 8 Wiring the Fault Alarm Contact c08 11 3 Mounting Installation cccceeeseeeeeeeneseeseeeeeeeees 12 3 1 DIN Rail Mounting ccccecceeeceeeeeeeeeee seen 12 3 2 Wall MOUNTING ccccecceeceeceeeeeeseeeaeeeeeeaees 14 4 Hardware Installation cccecssseeeseeesseeeseeeeeeees 15 4 1 Installation Steps sisiscndantiaseosincseceriectanbneaacmeantes 15 5 Network Application cccsccssccsseesseesenssenseeseenees 16 6 PFOUDIE SNOOUNO eiseisississo rraian 17 7 Technical Specification ccccssecesseceneeeeesenees 18 Antaira Industrial Ethernet Switches LNP 0702G SFP Series User Manual V1 0 1 Overview Antaira s LNP 1002G SFP industrial gigabit unmanaged Ethernet switch series are IP30 rated and DIN Rail mountable Each unit is designed with 8 gigabit Ethernet ports that are IEEE 8023 at compliant power over Ethernet plus and has two dual rate 100 1000 SFP slots making it ideal for applications that demand high bandwidth and long distance communication This product series provides high EFT and ESD protection to prevent any unregulated voltage and is suitable for harsh environments It supports the power redundancy feature using a dual power input design with reverse polarity protection In addition the built in relay warning function alerts maintainers when power failures occur The LNP 1002G SFP series includes two models one with an
12. fications of the product described in this manual without prior notice Antaira Technologies LLC will not be liable for any technical inaccuracies or typographical errors found in this guide Changes are periodically made to the information contained herein and will be incorporated into later versions of the manual The information contained is subject to change without prior notice Antaira Industrial Ethernet Switches LNP 1002G SFP Series User Manual V1 0 FCC Notice This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy It may cause harmful interference to radio communications if the equipment is not installed and used in accordance with the instructions However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which t
13. he receiver is connected e Consult the dealer or an experienced radio TV technician for help Caution Any changes or modifications not expressly approved by the grantee of this device could void the user s authority to operate the equipment CE Mark Warning This is a Class A product In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures Industrial Ethernet Switches Industrial Grade Gigabit Unmanaged Ethernet Switches User Manual Version 1 0 August 2014 This manual supports the following models e LNP 1002G SFP e LNP 1002G SFP T This document is the current official release manual Please check our website www antaira com for any updated manual or contact us by e mail support antaira com Antaira Industrial Ethernet Switches LNP 1002G SFP Series User Manual V1 0 Table of Contents TO VEE VIEW sosisini eTEN RANAR 1 1 1 Key FeatUreS ssiiineii enina nii 1 TZ Pack ade COMENTS sordat 2 1 3 SAlely Precautii aN 2 2 Hardware Description c ssceseceeeceeeeeseenseeneeeeeeees 3 2 1 Physical DIMENSION cccecceeeceeeeeeeeeeeeeeees 3 CAF 9 es B S ee eee ene ee eee ene 4 2G EONO Geeta ee nee eee ae ene eee ree ante cece 4 72 LEDINCI S eee ee ete ee eee meee eer ene 5 2S IMG RNCU Fr ONS osinn EA serene 5 AE ENEN Mere eRe reer er eer eter etn eee eee reer nee 7 2 Wiring the Power Inputs ccceeeee
14. ort service if the problem still cannot be resolved if the industrial switch LED indicators are normal and the connected cables are correct but the packets still cannot transmit please check the system s Ethernet devices configuration or status 17 Antaira Industrial Ethernet Switches LNP 1002G SFP Series User Manual V1 0 7 Technical Specification Table 7 1 has the technical specifications for Antaira s LNP 1002G SFP series 10 port industrial PoE gigabit unmanaged Ethernet switch with 4 10 100 1000Tx SOW Port and 2 100 1000 SFP slots IEEE 802 3 10BaseT Ethernet IEEE 802 3u 100Basel X Fast Ethernet Standard IEEE 802 3ab 1000BaseT IEEE 802 3z gigabit Fiber IEEE 802 3at power over Ethernet 14 880pps for Ethernet port Transfer Rate 148 800pps for fast Ethernet port 1 488 000pps for gigabit Ethernet port Transmission Speed Up to 1000Mbps MAC Address 8K table size 8 10 100 1000Tx 80W Port auto negotiation RJ45 Ethernet Port speed full half duplex mode and auto MDI MDI X connection RJ 45 port 1 8 support IEEE 802 3at end point alternative A mode PoE Pin Assignment Positive VCC Pin 1 2 Negative VCC RJ 45 pin 3 6 Data Pin 1 2 3 6 SFPSlot 2 SFP slots support dual rate 100 1000 Power Unit P1 Green P2 Green fault Red Ethernet port Link active Green 1000Mbps SFP Link active Green 10BaseT 2 pair UTP STP Cat 3 4 5 cable EIA TIA 568 100 ohm 100m Network Cable
15. rial Ethernet switch s hardware specs ports cabling information and wiring installation will be described within this user manual Antaira Industrial Ethernet Switches LNP 1002G SFP Series User Manual V1 0 2 Hardware Description 2 1 Physical Dimensions Figure 2 1 below shows the physical dimensions of Antaira s LNP 1002G SFP series 10 port industrial POE gigabit unmanaged Ethernet switch with 8 10 100 1000Tx 830W Port and 2 100 1000SFP slots W x D x H is 46mm x 99mm x 142mm Q v o o 9 S i e 9 9 Q Q 9 o o Y oooooooo DONN Qo 9 9 0 0 9 o 9 0 9 0 9 9 a 0 9 Top View Bottom View Front View Figure 2 1 LNP 1002G SFP Series Physical Dimensions Antaira Industrial Ethernet Switches LNP 1002G SFP Series User Manual V1 0 2 2 Front Panel The front panel of the LNP 1002G SFP series industrial PoE gigabit unmanaged Ethernet switch is shown below in Figure 2 2 Figure 2 2 The Front Panel of LNP 1002G SFP Series 2 3 Top View Figure 2 3 below shows the top panel of the LNP 1002G SFP series switch that is equipped with one 6 pin removal terminal block connector for dual DC power inputs 48 55VDC gaQeaQaqagqoeaQaqaqaqcaaqtcaaoaqgeqedaaga Figure 2 3 Top Panel View of LNP 1002G SFP Series Antaira Industrial Ethernet Switches LNP 1002G SFP Series User Manual V1 0 2 4 LED Indicators There are LED light indicators located on the f
16. ront panel of the industrial Ethernet switch that display the power status and network status Each LED indicator has a different color and has its own specific meaning see below in Table 2 1 On Power input 1 is active P1 Green Off Power input 1 is inactive 2 Power input 2 is active Power input 2 is inactive Power input 1 or 2 is inactive Fault Power input 1 and 2 are both functional or no power Sko link is active port alarm is disabled The port is The port is supplying power to the power to the Green PoE Indicators Green Port 1 8 No powered device attached or power supplying fails LNK ACT On Connected to network SFP Port Green e Networking is active Not connected to network Green a Connected to network 1000Mbps at eg 8 Flashing Networking is active e Off Not connected to network Connected to network 100Mbps 10Mbps LAN Pot toe _ ashing Table 2 1 LED Indicators for LNP 1002G SFP Series 2 5 Ethernet Ports Hi RJ 45 Ports RJ 45 Ports Auto MDI MDIX The RJ 45 ports are auto sensing for 10Base T 100Base TX or 1000Base T devices connections Auto MDI MDIX means that the switch can connect to another switch or workstation without changing the straight through or crossover cabling See the figures as below for straight through and crossover cabling schematics Antaira Industrial Ethernet Switches LNP 1002G SFP Series User Manual V1 0 Note m RJ 45 Pin Assignments Table
Download Pdf Manuals
Related Search