Starlight MPA Box Camera - Surveillance
Contents
1. INSTALLATION Q Using an appropriate mounting bracket mark and drill the necessary holes to mount the bracket to a wall or ceiling Attach the mounting bracket to the surface using machine screws Q Attach the box camera to the moun ing bracket Adjust the camera s position Consult the manual of mounting bracket for addi ional information INSTALLATION Q Connect an appropriate lens to he camera lens connector by twisting he lens clockwise The camera is compatible with any C or CS mount lens For C lenses please use the provided Adapter Ring See page 10 for details Lens is not included Connect the lens cable to the box s 1 Socket 0 Adjust the lens zoom and focus accordingly Consult the manual of the lens for additional information ADJUSTMENT OF BACK FOCUS Please make sure the lens is C or CS Mount To use C Mount lens please insert the included C ring to the lens then insert the lens To use CS Mount lens fix the lens directly into the front camera without the C ring CE NY TA Focus Adjustment To adjust the focus slide the focus lever on the side of the front camera Please tighten the focus lever after he adjustment in order to prevent being out of focus MODULE OSD MENU DW EXPOSURE COLOR DAY amp NIGHT FUNCTION LENS B BAL D amp N MODE SHARPNESS MANUAL DC ATW AWB PUSH AUTO COLOR B amp W 0 102. 734KHz H 59 95Hz V Synchronization Internal Horizontal Resolution 820 TV Lines B W 800 TV Lines Color Minimum Illumination F1 2 0 14 Lux Color 1 2 0 03 Lux B W S N Ratio 55dB AGC off Video Output CVBS 1 OVp p 75 Q Alarm Output 1 Alarm Output LENS Lens Type Compatible with C amp CS Mount Lenses OPERATIONAL Shutter Speed 50 60 60 000s Backlight OFF HME BLC WDR Star Light Sense Up OFF x2 x64 3D DNR OFF Low Middle High White Balance ATW AWB PUSH MANUAL Day and Night Auto Day Night Mirror Flip OFF ON Auto Gain Control 0 20 27 SPECIFICATIONS Intelligent Motion Detection Digital Quick Zoom Motion Detection Privacy Zones 4 Motion Regions 16 Programmable Privacy Masks Sharpness Gamma De Fog Operating Temperature Operating Humidity 20 C 60 C 4 F 140 F Less than 90 Non Condensing Power Requirement Dual Voltage DC12V 24VAC Power Consumption DC12V 2 SW 208 mA AC24V 2 75W 114 mA Housing Material Dimensions Weight 119 7 x 58 8 x 62 mm 4 71 x 2 31 x 2 48 Inch 28 Specification is subject to change without prior notice MEMO D pO GITAL WWATCHDOG Everything s Digital 5436 W Crenshaw St Tampa FL 33634 Tel 866 446 3595 813 888 9555 Fax 813 888 9262 www Digital Watchdog com technicalsupport dwcc tv Te
3. mode compensates for color temperature changes between 2400K and 11000 2 AWB Auto White Balance Control mode compensates for color temperature changes lower than 2000K and higher than 15000K PUSH Push fixes the white balance based on he current lighting automa ically MANUAL Users can control the white balance manually by changing RED GAIN and BLUE GAIN see below KELVIN Select from Low Middle or High If enabled the Red and Blue Gain settings will be set automatically according to the Kelvin settings RED GAIN 0 20 Adjusts the amount of red in the image BLUE GAIN 0 20 Adjust the amount of blue in the image U WHITE BAL MANUALLY KELVIN MIDDLE R GAIN 116 UMP 110 RETURN COLOR GAIN Set the color gain from 0 20 15 4 DAY amp NIGHT ODE D amp N AUTO In AUTO mode the camera switches between day and night automatically depending COLOR on light level If COLOR is selected the camera always stays in day color mode B amp W If B amp W is selected camera always stays in night B amp W mode CONTROL Select if he Day Night switch will be based on the AGC levels AUTO or using IR LED lights EXT AUTO if selected Day Night switch will depend on the AGC levels AGC Threshold Set when the camera switches between Day amp Night AGC Margin Set the value added to the AGC Threshold Adjust the value based on the environment in which the camera is instal
4. recommended 24 DW WARRANTY INFORMATION Digital Watchdog referred to as the Warrantor warrants the Digital Watchdog Camera against defects in materials or workmanship as follows LABOR For the initial five 5 years and one 1 year on IR LED from the original purchase date if the camera is determined to be defec ive the Warrantor will repair or replace the unit with a new or refurbished product at its option at no charge PARTS In addition the Warrantor will supply replacement parts for the initial five 5 years and one 1 year on IR LED To obtain warranty or out of warranty service please contact a Technical Support Representative at 1 866 446 3595 Monday through Friday from 9 00AM to 8 00PM Eastern Standard Time A purchase receipt or other proof of the original purchase date is required before warranty service is rendered This warranty only covers failures due to defects in materials and workmanship which arise during normal use This warranty does not cover damage which occurs in shipment or failures which are caused by products not supplied by he Warrantor or failures which result from accident misuse abuse neglect mishandling misapplication altera ion modification faulty installation set up adjustments improper antenna inadequate signal pickup maladjustment of consumer controls improper operation power line surge improper voltage supply lightning damage rental use of the product or service by a
5. D BNC Video Output AC DC Power Input Terminal Block 4 E S O DIMENSIONS IN MILLIMETERS IN 47 6 TN 14 5 0 57 2 tJ V io EX I I fi D 1 n 62 0 2 44 4 amp 119 7 4 71 gt 119 7 4 71 gt 131 8 5197 gt 58 8 2 31 gt w 55 0 2 17 gt 58 8 2 31 62 0 2 44 INSIDE THE BOX Included with C2 Box Camera Color Box User Manual Mini DIN Connector For Video or DC Auto Iris Lens Adapter Ring for Type Lenses Q Two Port Terminal Block for AC or DC Power Connection Q Cable Extension for Alarm In Out and RS 485 DW DIGITAL WATCHDOG ing Digital Everything s Box Camera ABOUT MANUAL Before installing and using the camera please read this manual Be sure to keep it handy for future reference STAR LIGHT MPA carefully
6. DN coss Everything s Digital Starlight MPA Box Camera DWC C261T STAR LIGHT MPR ABOUT MANUAL Before installing and using the camera please read this manual carefully Be sure to keep it handy for future reference 06252014 EDD SS sss lul ll l1 ZD PRECAUTIONS Do not open or modify Do not open the case except during maintenence and installation for it may be dangerous and can cause damages Do not put objects into the unit Keep metal objects and flammable substances from entering the camera It can cause fire short circuits or other damages Be careful when handling the unit To prevent damages do not drop the camera or subject it to shock or vibration Do not install near electric or magnetic fields Protect from humidity and dust Protect from high temperature Be careful when installing near the ceiling of kitchen or a boiler room as the temperature may rise to high levels Cleaning To remove dirt from the case moisten a soft cloth with a soft detergent solution and wipe Mounting Surface The material of the mounting surface must be strong enough to support the camera FCC COMPLIANCE This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of he FCC rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential environment This equipment generates us
7. R level in the submenu Select from Low Middle or High Default 13 EXPOSURE DRC DYNAMIC RANGE COMPRESSOR DRC enables dark areas in images to become more visible wi hout overexposing the bright areas to create one perfect image Select from Off Low Middle or High NOTE If WDR or DEFOG are enabled the DRC set ings are set automatically and will not be available for adjustment DEFOG Allows he camera to process a scene that is obscured by fog or weather conditions and provides a visibly improved image AUTO Manual Select AUTO to have the WDR and DRC levels adjusted automatically Set he DEFOG level from LOW MIDDLE HIGH E EXPOSURE LENS BACKLIGHT OFF DAC OFF AGC STARLIGHT KA 30 DMR HIGH EXIT JUMP AGC AUTO GAIN CONTROL 0 20 AGC enhances the picture brightness in low light conditions A higher level AGC setting makes the images brighter however it could increase the amount of noise STARLIGHT Automatically activates slow shutter function when the image is too dark OFF x2 x64 High values are not recommended as they may causes he image to lag Default X4 Starlight menu cannot be controlled if the SHUTTER setting is above 1 60 3D DNR 3D DIGITAL NOISE REDUCTION OFF LOW 3D DNR reduces the noise on the screen in low light conditions and MID HIGH allows for clearer images even at night 14 DW COLOR WB MODE ATW Auto Tracking White Balance Control
8. T ENT CONTROL GAMMA DRC Bat JUMP ds OFF LOW MIDDLE HIGH DEFOG r FLIP OFF ON LOW MIDDLE HIGH OFF ON AGC B amp W BURST D ZOOM 0 20 x8 STARLIGHT SMART IR E SENE or rid EXIT JUMP OFF LOW MID HIGH eve EXI EXIT EXIT JUMP SAVE amp EXIT EXIT MOTION PRIVACY SETUP EXIT MOTION ZONE NUM COMMUNICA SAVE amp EXIT ALARM 2 PAUDRATE pr 4800 9600 SHAKING OFF ON ZO NE DISP 57600 115200 EXIT un NGAYA Ja 718 QUICK ZOOM V PO S Seal S OFF ON H SIZE JAPANESE KOREAN EXIT JUMP 0 40 SPECIAL SAVE amp EXIT EXIT V SIZE DEFECT DET TV MODE O LP F 0 31 INITIAL Y LEVEL ON 20 EXIT JUMP CR LEVEL SAVE amp EXIT EXIT CB LEVEL EXIT JUMP SAVE amp EXIT EXIT 11 oro EXPOSURE EXPOSURE EENG er EE Manual Manual mode supports the fixed board lens or the manual BACKLIGHT OFF iris lens DRC DC DC mode supports the auto iris varifocal lens 3D DNR 7 HIGH NOTE Both MANUAL and DC mode have FOCUS ADJ You can Abas adjust the focus by finding the highest number on he FOCUS SET DC Lens Submenu MANUAL Lens Submenu DEBLUR a LH DUK BRIGHTHESS 10 SHUTTER AW TO a FOCUS ADJ RETURN Mode MANUAL Set the lens mode to Normal or Deblur DC Set he lens mode to Outdoor Indoor or Deblur Brightness Adjust the camera s brightness from 0 20 The higher the number the brighter the image will appear Shutter Set he shutte
9. arm on the screen when movement is detected ALARM Select to enable or disable he camera s motion detection and select which conditions will trigger the alarm from the following op ions Shaking ON OFF Camera Moving will appear if the camera is shaken abruptly Shaking Scale 0 20 The lower the number the more sensitive the camera will be to shocks or vibra ions Bright Change ON OFF Birght Change will appear if the brighness 9 in the scene changes suddenly and drstically ages Bright Scale 0 20 The lower the number the more sensitive the camera is to brightness changes in the scene SHAKING QUICK ZOOM The camera can automa ically digitally zoom in when mo ion is detected In he submenu setup he following MOVING Set the camera s movement speed 30 60 0 5 Second is the default speed Max speed 240 60 4 Seconds ZOOM IN Set the camera s zooming speed 30 60 0 5 Second is he default speed Max speed 240 60 4 Seconds STAND BY Setup the dwell time for the camera to remain zoomed in 30 60 0 5 Second is he default soeed Max speed 240 60 4 Seconds SYNCHRONOUS Set by default Should not be changed TRACKING The camera keeps tracking the moving area and operates Zoom In Out REPEAT The camera will continue to zoom into motion as it detects it in different parts of the camera s view 20 DW PRIVACY You can hide some parts of the screen for pri
10. chnical Support Hours Monday Friday 9 00am to 8 00pm EST
11. es and radiates radio frequency energy and if it is not installed and used in accordance wi h the instruction manual it may cause harmful interference to radio communications WARNING Changes or modifications are not expressly approved by he manufacturer ABLE OF CONTENTS Introduction ________ Features 22222222222 4 Parts and Descriptions 5 Dimensions uiu reli 2 2 2 2 2 ER DEN 6 Installation Inside the BOX 22222222222 2 2 2 ee 7 Mount Installation Instructions 2 22 2 8 9 Adjustment of Focus 222222 10 Module OSD Menu ______________ _ _ _ _ _ __ LLL LL LLL LLL 11 23 Troubleshooting 24 Warranty Information 25 26 Specifications _______________ _ _ ___ iit 27 28 FEATURES 1 3 Sony 1 3M CMOS 820 TV Lines B W 800 TV Lines Color Compatible with C CS Mount Lenses True Day amp Night with IR Cut Filter 3D DNR 30 Digital Noise Reduction WDR Wide Dynamic Range Star Light Super Low Light Technology HME Highlight Masking Exposure Defog Extreme Weather Image Copmensation Digital Quick Zoom amp 8x Digital Zoom 16 9 and 4 3 Viewing Modes 1 Alarm Output AGC BLC AWB Privacy Zones 16 amp 4 Motion Detection Zones Camera Control via RS 485 UTC RS485 Built In PARTS amp DESCRIPTION Q Lens Connector Q Box Camera Moun ing Bracket Connectors lris Socket Q Back Focus Q Alarm RS485 Connector OSD Control Arrows and Enter Buttons Power LE
12. ld Adjust this value based on the environment in which the camera is installed Night Mode Select what will the camera do when the light threshold is met for Night Model Select to keep in color or switch to B amp W At the bottom of the screen the settings will be summarized for your review The informa ion includes according to current settings the CDS threshold for Day to switch to Night CDS threshold for Night to switch AGC THRES back to Day and current CDS level for reference EXT LED AUTO OFF AUTO Enables the IR LED board OFF disable the camera s LEDs DELAY Low Mid High Time interval delay before switching from day mode to night mode B amp W BURST ON OFF If ON is selected the camera provides a color burst signal in night mode SMART IR O20 Enable Smart IR and set the level Higher values will make Smart IR stronger 17 FUNCTION SHARPNESS 0 10 Sets he image sharpness higher the number the sharper the image GAMMA 045 065 Select the desired gamma level 0 55 is default setting MIRROR FLIP OFF MRROR Reflects the camera horizontally FLIP Reflects the camera vertically 218 85 78 Mirror Flip OFF Mirror ON Flip ON Mirror amp Flip ON D Zoom 1 0 8 0x Enable or Disable Digital zoom to the camera s field of view By default he zoom will go to the center of the camera s Field of View DW MOTION The camera can detect the movement and display an alarm
13. led Night Mode Select what will the camera do when light threshold is met for Night Mode Select to keep in color or switch to B amp W At he bottom of the screen the settings will be summarized for your review The information includes according to current settings the AGC threshold for Day to switch to Night AGC threshold for Night to switch back to Day and current AGC level for reference EXT if selected adjust the external signal to CDS or LOW HIGH Low High The camera s Day Night switch will be set according to an external LED board Set to HIGH to make the camera switch to night mode only when there is very little light Night Mode Select what will the camera do when light threshold is met for Night Mode for Night Model Select to keep in color or switch to B amp W At he bottom of the screen the settings will be summarized for your review The information includes according to current settings the EXT level for Day to switch to Night EXT level for Night to switch back to Day and current EXT level for reference DW 4 DAY amp NIGHT CONTROL CONT CDS The camera s Day Night switch will be set according to the LED board in the camera CDS Threshold Marks the light level at which the camera will switch between color and B W The lower he value the camera will require less light more darkness to switch to Night Mode CDS Signal The value added to the CDS Thresho
14. nyone other than an authorized repair facility or damage that is attributable to acts of God 25 LIMITS amp EXCLUSIONS There are no express warranties except as listed The warrantor will not be liable for incidental or consequential damages including damage to recording media without limitation resulting from the use of these products or arising out of any breach of the warranty All express and implied warranties including the warranties of merchantability and fitness for particular purpose are limited to the applicable warranty period set forth above Some states do not allow the exclusion or limitation of incidental or consequential damages or limitatons on how long an implied warranty lasts so the exclusions or limitations listed above may not apply to you This warranty gives you specific legal rights and you may also have other rights that vary from state to state If the problem is not handled to your satisfaction then write to the following address Digital Watchdog Inc ATTN RMA Department 5436 W Crenshaw Street Tampa FL 33634 Service calls which do not involve defective materials or workmanship as determined by the Warrantor in its sole discretion are not covered Costs of such service calls are the responsibility of the purchaser 26 SPECIFICATIONS VIDEO Image Sensor 1 3 Sony 1 3 Mega Pixel CMOS Sensor Active Pixels 1280 H x 1024 V Scanning System 2 1 Interlace Frequency 15
15. on the screen when movement is detected MOTION OFF ON Select to enable or disable the camera s motion detection If ON is selected DET SETTINGS Use this submenu to adjust the motion detection s sensi ivity detection dwell time Motion Estimate and setup a Signal Output Action Sensitivity The smaller he movement you want to detect the higher the sensitivity value must be Object Keep LV Set the dwell time for how long motion is detected Mo ion Es imate Predicts possible direc ion once mo ion is disappeared by wall or curtain The lower the number the more sensitive the camera will be to new motion once detected Signal Out If Alarm is enabled when motion is detected the camera can support 3 3V power output to an external signal MOTION SET Window Tone Set the size of the zone s borders Window Zone The camera supports up to 4 different mo ion detection zones Window Use Select which one of the motion areas to enable DET H POS Move the Zone left or right The higher the number the zone will move to the right DET V POS Move the Zone up or down The higher the number the zone will move down DET H Size Adjust the zone s size horizontally The higher the number the right side panel will move further to the right DET V Size Reset the zone s size vertically The higher the number the bottom side panel will move further down 19 MOTION The camera can detect the movement and display an al
16. r speed to AUTO Manual or FLC Flicker less mode Select FLC if the camera is experiencing some flickering in the image If selected the shutter speed will automatically be set to 1 100 for NTSC or 1 120 for PAL If Manual is selected set the shutter speed from 1 60 to 1 60000 Focus Adjustment When on he default level is set automatically by controlling lens focus and based on the installation and environment circumstances EXPOSURE BACKLIGHT OFF HME HIGHLIGHT MASKING EXPOSURE HME allows objects to appear clearly on the screen by masking extremely bright areas To setup HME set the level and mode The lower the setting the darker the masking areas have to be Select from 0 20 Mode Select when to enable HME settings Select from All Day Run HME always or Night Only HME is EXIT JUMP enabled only in B W mode AGC STARLIGHT 30 DHR BLC BACK LIGHT COMPENSATION If BLC is selected adjust the size nad position of the mask H POS Move the Zone position left or right The higher the number the zone will move to the right V POS Move the Zone position up or down The higher the number the zone will move down H Size Reset the zone s size horizontally The higher the number the right side panel will move further to the right V Size Reset the zone s size vertically The higher he number the bottom side panel will move further down WDR Wide Dynamic Range If WDR is selected adjust the WD
17. the camera is set to NORMAL 4 3 If applicable set it to 16 9 LANGUAGE The Camera supports the following languages English Default Chinese Chinese S Japanese and Koran SPECIAL DEFECT DET The camera can detect and correct dead pixels in the image To do so press the select button and set the hreshold level The camera will detect and adjust the pixels automa ically TV MODE Set the camera to NTSC Default or PAL OLPF Select the filter that you use from RED and PASS then reboot the camera to use DEFECT DET OW TV MODI BET RED CUT M RETURN INITIAL Reset the camera to its factory default settings To do so press and hold the select button for five 5 seconds 22 BB EXIT EXIT SAVE Exit the OSD menu after saving the recent changes INITIAL Exit the OSD menu after resetting the camera to factory default SAVEREXIT4 23 ROUBLESHOOTING Before sending your camera for repair check the following or contact our technical specialist FOR NO VIDEO Check the coaxial cable and make sure it is connected securely Check the lens iris adjustment at the camera s OSD menu Check the power supply and make sure the camera has the proper voltage and Current FOR OUT OF FOCUS VIDEO Check the clear dome cover and the lens for dirt or fingerprints Use a soft cloth and gently clean Check the lens manual focal and zoom adjustment The use of a field test monitor is
18. vacy masking A total of 8 different privacy masking zones are available PRIVACY SET Select the zone number you want to setup yy To enable it turn the display option ON ZONE NUM H POS Move he Zone position Left or right The higher the L number the zone will move to the right POS V POS Move the Zone position up or down The higher the number the zone will move down H Size Reset he zone s size horizontally The higher the number the right side panel will move further to the right V Size Reset the zone s size vertically The higher the number the bottom side panel will move further down MASK COLOR To adjust the mask s color use the Y CR and CB Levels Y Level The higher the number the brighter the color will appear CR Level The higher the number the more red tone will be added to the zone s color The lower the number the more green will be added to the zone s color CB Level High CB Level High CR Level Red High CB Level Low CR Level Blue Low CB Level High CR Level Orange 21 SETUP COMMUNICATION Use this setup menu to adjust the camera s ID and Baudrate aye The 5 default Protocol is Pelco D COMMUNICA CAM ID Provide an ID number for the camera 0 255 LANGUAGI BAUDRATE 9600bps is default Select the baudrate from the following options 2400 4800 9600 57600 1 15200 bps VIEW ANGLE 4 3 16 9 Adjust the camera s aspect ratio By default
Download Pdf Manuals
Related Search