WA-1100-K
Contents
1. Press the button to set the Armed Away alert After the exit delay the Arm LED will illuminate steady and the system is armed in the AWAY mode 00 HOME SECURITY Armed AWAY H HOME Press the HOME button to set Armed Home alert After the exit delay the Arm LED will blink and the system is armed in the AWAY mode 00 HOME SECURITY Armed HOME Check Function Press the CHECK button to check the programmed data without any password It can only review but it can not change the data in the Check Mode The menu structure is listed below Check 0 T To review 1 Exit Exit time 2 Alarm Alarm time 3 Entry Entry time 123456 P To review phone number sets 7 MSG To review recorded message 8 DIAL To review dial mode Programmed devices can be checked without the activation of the alarm When the main console receives data from the device sensor the LCD displays zone label status to confirm proper communication between the device console status Speed Dial Function e Press and hold the SP DIAL button and the assigned button The Main console will automatically execute the autodial and alarm If you want to cancel the autodial and alarm when they are activated key in the Master password to cancel them or use the Remote Control disarm button 13 e 4 the autodial order is Preset 4 gt Preset 1 gt Preset2 gt Preset 3 Burglary condition e 5 the au2. 1p gp 489 2 t Hio i 32 Specifications Frequency 303 Mhz Power Source AC120V DC 12V Items Specifications Power Consumption 70mA idle 170mA activated Back up Battery Optional Approximate 7 hours NO AC adaptor 0 C 40 C Temperature Range RF Range 100 feet in open air space Security Code Hopping code Alarm Activation Time 1 255 seconds available alarm time setting Dialing Type Tone Voice Message Playing Time Total 25 seconds Preset Telephone Numbers 6 phone numbers 20 digits for each number Material ABS Weight 650g Dimensions 26 cm X 17 cm X 3 5 cm 36 37 Installation template for wall mounting of main control panel 1 Use the template on the right to mark positions for mounting screws to install the main control panel on the wall Once the mounting screw positions have been marked drill 3 16 pilot holes and install the plastic wall anchors supplied Install the mounting screws into the plastic wall anchors so that the heed of the screw extends approximately 1 4 from the wall Remove the rubber plugs located at the top 2 holes on the bottom of the main control panel and line up these holes with the mounting screw heads Slide the main control panel over the mounting screws and gently push down onto the screws so that it is secure 38
3. 2 to change the Master code menu Setting Change code 2 Master 135246 3 2 Sequence Programming Menu This menu for code learning establishes a link between all sensors other wireless devices and the main console The main console has to learn the code for all sensors other wireless devices and set a sequence learning order as well as assign the zone for all programmed sensor accessory devices The system can be programmed for up to 63 devices It is recommended that the sequence learning order number be marked on the individual wireless device and recorded in the Summary of Sensors and Zones Settings so that the user can replace clear the wireless device if it s required In the system menu SYS OPTS 0 SYS OPTS 1 SEQ 2 REPLAC 3 CLR Press 1 to go into the sequential programming mode Sequential Pgming Trigger Sensor 01 01 sequence learning order The method for sensors learning 1 PIR Motion Detector Install the Battery and select the Power Switch position from OFF to C position PIR sensor LED will light for 1 Sec This means that the sensor will transmit a 1sec signal You can also move in the front of the PIR It will detect your movement and transmit a 1 sec signal The sensor will learn into the main console 2 Door Window Detector Install the Battery and let the magnetic switch go from a close position to an open position The LED will light for 1 Sec The sensor will learn into the ma
4. Armed Home mode you need to Disarm the system with the first call and a second call to change the Arm status If you do not disarm first and press 1 or 2 directly the system will emit bi bi bi and reject your setting You must press 3 to disarm first Note this function will work on touch tone service lines only Auto dialer priority This system stores up to six 6 telephone numbers in the Main Console If it is triggered and an alarm is activated the auto dialer will call the 4 preset telephone numbers that you programmed listed below and play your pre recorded message If system is triggered Burglary help It will automatically dial Preset 4 gt Preset 1 Preset 2 gt Preset3 phone numbers for 3 cycles 4 1 2 3 When the telephone is answered it will playback the message 2 times Fire help It will automatically dial Preset 5 gt Preset 1 gt Preset 2 gt Preset 3 phone numbers for 3 cycles 5 1 2 3 When the telephone is answered it will playback the message 2 times 14 Medical help It will automatically dial Preset 6 gt Preset 1 gt Preset 2 gt Preset 3 phone numbers for 3 cycles 6 1 2 3 When the telephone is answered it will playback the message 2 times LCD MSG Message indicating on LCD This system will leave a warning message on the LCD panel when the sensors are opened triggered or in a low battery condition It also emits 3 short Beeps ever
5. Console s LCD display Door Window Detector for DC 12V battery Button function Magnet Transmit LED When the sensor is activated the LED will light for 1 sec Magnet sensor Battery Cover Remove the cover and install one 12V alkaline battery here LEGEND 1 MAG Z MACNE CENCGAD 3 MAGN SENSUR Note The magnet and magnet sensor must be placed in parallel position triangle arrow ED to ensure a better setting 4 BATTERY COVER Change the Battery When the sensor sends a low battery message to the main console remove the old battery 19 and replace it with a fresh alkaline battery The low battery message on the LCD is shown below 63 WINDOW SENSOR 01 Low battery Zone address setting You can set the sensor as Door or Window detector by using the jumper selector If you want to set the sensor as a Door sensor put the Jumper on the D side If the set Jumper is on the W side the sensor becomes a Window sensor DOOR WINDOW SELECT TYPE SEL JUMPER DOOR WINDOW Notes on the Door Window Detector 1 The LED on the sensor will flash once when the sensor is triggered 2 There cannot be a gap greater than 1 4 inch 5 mm between the magnet sensor and the magnet otherwise the sensor will not work properly Enter the installer password and press the 1 button to activate the Sequence Programming Menu Take the magnet away fr
6. LT SERRE 11 Function for Master Menu sssssssssss emere 12 Check Function s wizer aaan e cence EEE E e AEAEE 13 Speed Dial Functi h e eee a e a aA eene 13 Arm or Disarm via the Telephone Line sssssssnsne 14 Auto Dialer Priority soida penp gaa nu RE re Re ERR EE 14 Ee DE LT Im etne aniar sated ae ada aea e i aest 15 24 Hour Home amp Away Functions sssssssessssssssssssess eene 15 Remote Control Handset ssssssssssssssssssssssssssesese eene heme eene 16 PIR Motion Detector 1 2 i04 oci cet ds D cret dede dore te eo pedi eat da Dd e ee 17 Door Window Detector ea ipit ces ont ORE d de gae Lx M at Rei Eug 19 MIA SIREN TI 22 Panic Watch Transmitter 0 ccccec cece eee eee ee eee eee e eee eee eeeeeeee nent eaeaeaeaes 23 Smoke Detector sr eate iioi t c tee a ee 25 Door Keypad Detector ssssssssssssssssssssssssememmememe eene eee 27 Gas DeteCtOn x Scere EE 28 Range Extender c ce oretsdedecuhatearae shad Ee rares ee Iit pA poe Sedes PEE x de ERES 32 Summary of Program Main Console sss 34 Summary of Sensors and Zone Settings ssssssssssssssseeese 35 Specificati ns 2 cron oi eee editos anes ah De S Tea Peu Rhee eis 36 Installation Template ette tei Laert HIE Rd ne UENIRE nexa Ped 37 Important Safety Instructions WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT EXPOSE THIS APPLIANC
7. The main console will receive the sensor signal and leave a message on the LCD display for about 2 seconds Note Checking this will require two people INSTALLING POSITION REFERENCE FOR DOOR WINDOW DETECTOR MAGNET MAGNET SWITCH 21 Mini Siren The siren is an effective deterrent to intruders Choose a location inside your home where the siren is not plainly visible but can be heard throughout the house It is important to install the siren where the cable can be hidden and discreetly out of reach of potential intruders or anyone likely to tamper with the system When the siren is installed and the system is set to Arm it will emit a piercing 110 decibel siren once a sensor detector activates the alarm Plug the wire into the control panel OUTPUT JACK Cord length 8 meters Loudness output 110 db Dimensions 3 7 x 4 5 x 2 cm Weight 120g including the cord IROUN 22 Panic Watch Transmitter The Panic Watch Transmitter is an idea for the elder or the child stays indoors while on panic medical emergency to press the red button and emit the signal via hopping code communication with the main console unit to trigger out the auto dialer system It has 2 changeable types with the wrest belt and the pendant to carry with LEGEND 1 PANIC KEY 2 TRANSMIT LED 3 BATTERY 4 PENDAN Transmitting range 100 feet in open air space Power 12V DC alkaline battery 23 Settin
8. e When the sensor sends a low battery message to main console remove the old battery and replace it with a fresh alkaline battery The LCD is shown below 63 PIR SENSOR 01 Low battery Zone Address Setting Enter the Installer password and press 1 to activate the Sequence Programming Menu after installing the battery for the PIR sensor Set the power switch from OFF to C position The red LED will blink for 1 second and activate the PIR sensor by moving in front of the PIR Sensor The Main Console will emit one Beep and the LCD will display Sensor Added The PIR sensor has been programmed into the main console successfully When the main console is in the armed mode the PIR detects movement of human or animals cat dog A message will be displayed on the LCD as shown below 63 PIR SENSOR 01 Zone Notes on the Position when Installed The PIR Motion sensor detects the movement of humans and animals within their range In order to prevent false alarms we recommend that you do not install any motion sensor in the following areas Do not install any PIR motion sensor in the following areas e Where there is a device that causes rapid temperature change or rapid heat transfer For instance near an air conditioner fire place heater or other intermittent heat sources e Where the sensor will be exposed to direct sunlight e Near large electrical devices and or high output radio frequency sources like a refrigerator m
9. is normally lasting for 5 6 hours at least when stand by A frequent check of battery is strongly recommended when use the backup battery 8MR 300 in range extender And also it is necessary to charge battery for at least 72 hours before checking the battery To check with following process 1 Unplug the AC adapter 2 Battery is working normally if POWER LED stays lighting on 3 If POWER LED turns off it needs to replace a new rechargeable battery Specifications Range Extender Power Source 12V AC adapter 33 Back up battery 9 6V 300mA Transmitting range 300 feet in open air space Dimensions cm 15 5 L x 10 7 x 3 5 Weight 500 grams includes AC adapter summary of Program Main Console Use the following form to record your programming choices for future reference e J RN LI KHEN NN LI HEN NN LINEEEEN NEN LICHEN NN ewe Pp LT UTERE NEN Preset Telephone No for Auto dialing M TI e E eC mm Deren e e esre e er E 34 Summary of Sensors and Zone Settings Use the following form to record the setting detail of sensors Learning Place of Learning Place of Zone Label Zone Label Number Installation Number Installation 05 2Fxxrom Widowi 3 J Learning Place of Zone Label Learning Place of Number Installation Number Installation Zone Label 30 62 L 9
10. stairs and doorways may be blocked in the event of a fire 31 Range Extender The Range Extender is a booster for extending transmitting range It can enlarge protection area to satisfy the needs for bigger houses premises etc The effective working range for transmitting distance is about 300 feet RANGE EXTENDER Main Features 1 R T LED range indicator T Transmit flash in orange light when the range extender is transmitting R Receive flash in green light when range extender is receiving Power LED glows when the system is powered DC Power Jack it connects AC power adapter and DC output lead to the range extender Antenna Pull out upward to enable maximum range of receiving and transmitting between Detectors and the Main Console Unit Function Switch to select the receiving party with Sensor or Extender particularly avoid the signals mixing up when have 2 units of range extenders installed X There are 2 modes of transmitting as below charts For Sensor Mode Use pw For Extender Mode Use Sensor switch Range extender B is only transmitting the signal of the detector not of Extender Range extender A to Main Console 32 Extender switch Range extender B is only transmitting the signal of Extender Range extender A not of the detector to Main Console 4 Rechargeable battery WA 126 BAT specially used for range extender optio
11. system it can not be used to unlock the system Please make sure to enter the correct password when the system is turned ON for the first time Home Security Keyboard Locked iii If 9 incorrect passwords are entered and 3 consecutive Keyboard Lock occurs then the system will trigger the alarm for a set duration and will be locked disabled The LCD will display as shown below The dialer will not dial out any of the phone numbers programmed The disarm button on the remote control handset can be used to disarm unlock the system System Lock 2 If the password is correct default 123456 the system will emit a beeping sound and the LCD panel will look like this shown below Access Granted Install Mode SYS OPTS 0 SYS OPTS 1 SEQ 2 REPLAC 3 CLR 3 Select the System Menu Number 3 1 System Option menu Press 0 to start setting Setting 0 T 123456 P 7 MSG 8 DIAL 9 CODE 1 0 T For time setting Default is 30 seconds minimum 1 second maximum 255 seconds Press the o button to go to the time setting exit alarm entry time Setting Time 1 Exit 2 Alarm 3 Entry Press the button to set the delay time for exiting the house The default time is 30 Sec You can set the time from 1 to 255 Sec Press the Enter button to finish the setting Setting Time 1 Exit 30 Sec Press button setting alarm time for triggering alarm The default time is 30 Sec you can set the time from 1 to 255 Se
12. will automatically count down from 25 Sec Please note The message should include pertinent information such as your name address and telephone number Setting Message Rec Sel Msg 1 25 Sec When the recorded message is finished it will automatically playback the recorded message The LCD panel is shown below Setting Message Play Sel Msg 1 25 Sec 4 8 DIAL To set a Dial mode Default is 2 ALL to dial all telephone numbers programmed Setting Dialer Mode 1 Single 2 All 2 Press 1 for a single attempt dial The dialer will stop dialing when one of the phone numbers are answered or 3 cycle dialing attempts are complete Setting Dialer Mode 1 Single 2 All 1 Press 2 for a 3 cycle attempt dial the dialer will stop dialing when all the programmed phone numbers are answered or 3 cycle dialing attempts are complete Note The answered phone numbers will be excluded from the dial sequence Setting Dialer Mode 1 Single 2 All 2 5 9 CODE To make a password change factory defaults 1 Install 123456 2 Master 135246 If you want to change the password key in the 6 Digits It will automatically show OK max set 6 digits If it is less than 6 digits you can press ENTER after keying in the number and it will show OK Setting Change Code 1 Install 2 Master Press 1 to change the Install code menu Setting Change Code 1 Install 12345 Press
13. 0 10 by volume in air 0 05 by volume in air 29 Powering up the system The Gas detector is powered by AC Therefore it is necessary to mount the detector to a wall but after learning into the system where is easily within reach of an AC power point Setting the Gas Detector Main Console is under learning mode to press the Test Reset button and the main console will sound beep to complete the setting successfully Notes It takes one minute to warm up the sensor to start detecting Installation Instructions 1 Mount the detector onto the wall with screws provided 2 Mount in 1 foot measured vertically from the highest point of the ceiling for natural gas detect or 1 foot above the floor for LP gas detect and measured horizontally between 3 feet to 10 feet for both gas Detect Depending on which flammable gas will be detected This gas detector is designed for use inside a single family home apartment or garage 3 Do not install this gas detector in the following areas a Where the temperature is usually below 40 4 4 or exceeds 120 49 humidity over 95 b Within 3 feet 1m of any cooking appliance c In unventilated rooms where paint or thinner or contaminant such as cleaning supplies may be stored d Boats or RVs Multiple family bldg unless there is a detector in each family unit e In a hazardous location as defined in the National Electrical code CAUTION This gas detector wi
14. 2 to go into the replace sensor mode Replace Sensor Enter Sensor Num Trigger Sensor To Replace 01 Once replaced It will go back to the system menu as shown below SYS OPTS 0 SYS OPTS 1 SEQ 2 REPLAC 3 CLR 3 4 Clear Menu Clear Sensors 1 Single 2 All Select 1 Single key in the sequencing learning order number and press It will clear that sensor If you select 2 All all learned sensors will be cleared Press 3 to go into the clear mode Clear Sensor 1 Single 2 All Press 1 and key in the sequence learning order number Press ENTER to clear the sensor Clear Sensor 1 Single Num xx Clear Sensor Clear OK Num xx Press It will display the words Are you sure Press ENTER to clear all learned sensors Clear Sensor Are You Sure Enter Clear Sensor Waiting Clear Sensor Clear All OK Function for Master Menu Factory Default Password 135246 1 Enter the Master code 135246 LCD display shown below 00 HOME SECURITY Disarmed Code AX e If the password is incorrect the main console will emit a Beep Warning sound LCD display shown below Access Denied 12 e If the password is correct the main console will emit a long beep sound LCD display shown below Access Granted Master Mode MASTER A AWAY H HOME Now the system will select the arm mode and set the system in either Away arm Home Arm mode see below A AWAY
15. E OR POWER ADAPTER TO WATER OR MOISTURE Read Instructions All the safety and operating instructions should be read before operating this equipment These instructions should be retained for future reference Heed Warnings All warnings on the equipment and in the operating instructions should be adhered to All instructions regarding care and operation of this equipment should be followed Power Sources Equipment should only be connected to the power supply specified in the operating instructions or as marked on the equipment Grounding or Polarization Take precautions that the equipment is properly grounded Take note that the power supply is fitted in the correct input jack marked DC 12V and auxiliary units external siren and strobe light are fitted into the correct external jack points Power Cord Protection Keep cable cords and plugs clear of other objects particularly at the point where they exit the equipment Cleaning Clean the equipment by wiping with a soft cloth do not use any abrasive agents or water Non use Periods Power cords should be unplugged from the outlet when left unused for a long period of time Object and Liquid Entry Take care not to drop objects or liquids on any part of the equipment Damage Requiring Service The alarm should be serviced by a qualified service personnel when The power supply cord or the plug has been damaged or Objects have fallen or liquid has
16. EY 3 AWAY KEY 4 HOME KEY 5 PANIC KEY 6 BATTERY TRANSMIT LED The LED will light when the device is transmitting DISARM Press this button to disarm the system or clear the message AWAY Press this button to set the system in the AWAY Arm mode HOME Press this button to set the system in the HOME Arm mode PANIC Press this button to trigger the alarm and activate auto dialer BATTERY COMPARTMENT For 12V alkaline battery OnrWN gt Zone Address Setting Enter the Installer code and press 1 to activate the Sequencing Programming Menu Press the PANIC button for 1 sec the red LED will also light for 1 sec The main console will emit a long Beep and the LCD panel will show Sensor Added The sensor has been set successfully To Arm or Disarm with the Remote Control Handset Press the AWAY button to arm the system in the AWAY mode 63 REMOTE SENSOR Armed AWAY Press the HOME button to arm the system in the HOME mode 63 REMOTE SENSOR Armed HOME Press the PANIC button to activate the PANIC function The activation of the PANIC function will immediately trigger the alarm and auto dialer 16 The PIR Motion Detector is designed to detect the movement of objects in a room or hallway The effective range of the motion sensor is 30 feet long with an 84 degree horizontal angle Before using this sensor please program this sensor into the main console via the sequence p
17. Wireless Security amp Safety System WA 1100 K OWNER S MANUAL Table of Contents Introd ctlor zi eid e epe t veio obe ete Oe dpa e tec ie deo rns 3 System Package sienne ee eee e cece eee eee e ee ee eee ceases nenne nennen enne 3 Optional ACCESSONES iscir one etre eter ies demit Me dae et Len ar ade 3 Planning for Installation Choosing a Location seat d Re Ree pa EAR ta a ee 4 Setting Alarm Zones iris scole ee poe ete IRI I SET E PA He Deae tees 4 Installing the Back up Battery cceceeeececeec tees ee eeeeeeeeaeeeeesasees 4 Powering the Main Console ccececeeeceeeeeeeeeeeeeeeeeeeaeaeaeaeaeaes 4 Connecting the Telephone Line sess 5 Setting the Antenna ssssssssssssssssssssssss emen emen 5 Mounting the Main Console ssssssss eee 5 About PasswotdS oen stie poker rb ie HEHNRR Rien REHEANERRUSS TIG VEU EUER aed 5 Others coin aee ose iret eoe db o ot x Pop sat i rester ERR Sea i MEDI 5 Operation Main Console ccccecec cece cece tees ee cece este memes meses enne 6 ECD Panel lll sttatiOn 3 otn per antes e ree tee andae ke tate 6 Function for Installer Menu sss 7 System Option Menu sssssssssssssssssssn mee eem nere 8 Sequence Programming Menu sessssssss 10 Replacement Menu ssssssssssssssssseememememe hne ene 11 Clear Menus 2 eui aate re bere itae HEEL RE
18. been spilled onto the equipment or The equipment has been exposed to rain or The equipment does not appear to operate normally or exhibits a marked change in performance or The equipment has been dropped and or the enclosure has been damaged Servicing Do not attempt to service the appliance beyond that described in the operating instructions All other servicing should be referred to a Qualified Distributor s Service Personnel System Maintenance Under normal use your system requires virtually no maintenance other than regular testing It is recommended that you test your system once a week and replace the batteries at least once every 6 months or as needed IMPORTANT NOTE IF YOU RETURN TO YOUR PREMISES AND FIND THAT THE ALARM IS IN PROGRESS DO NOT ENTER AS AFIRE OR AN INTRUDER MAY BE PRESENT GO TO A NEIGHBOR AND CONTACT THE RELEVANT LOCAL AUTHORITIES FROM THERE Introduction Thank you for choosing our Wireless Security amp Safety System These security systems are high quality reliable and versatile This system has a built in Auto dialer for increased security To ensure the best performance of your system please read this manual thoroughly and follow the precautions and instructions presented These systems are designed to be simple and easy to install and maintain Wireless easy to use No messy and expensive wiring is required to install the system Expandability You can add different types of ac
19. c Press Enter button to finish the setting Setting Time 2 Alarm 30 Sec Press button setting delay time for entering house The default time is 30 seconds You can set the time from 1 to 255 Sec Press Enter button to finish the setting Setting Time 3 Entry 30 Sec 2 123456 P Numeric key To set the telephone number you can program up to 6 telephone numbers each one being up to 20 digits each Example Press the 1 Button the LCD panel will appear as shown below Enter the phone number then press the ENTER button to program Press the 2 button to program Phone number 2 Setting Phone Num 1 kkkkkkkkkkkkkkkkkkkk Setting or For neighbors relatives friends and family members to notify in case of emergencies Setting The first priority dial in case of Burglary check with the police dept if this is acceptable 8 Setting The first priority dial in case of Fire check with the fire dept if this is acceptable Setting 6 The first priority dial in case of Medical help check with the hospital if this is acceptable Note The dialer will work with a touch tone service line only 3 7 MSG To set a recorded message which contains 1 segment of message for a maximum of 25 seconds If the recorded message is less than 25 Sec press to end the recorded message When alarm is triggered it will play the recorded voice message Press to start recording your message it
20. cessories to the system to create a more complex system as your future needs may require Flexibility You can choose the type of sensors and response actions for the system Personalized Program the system to notify whoever you choose in the case of an alarm activation System Package WA 1100 K Main Console X1 Remote Control WA 129 RC X1 PIR Motion Detector WA 120 MD X 1 Door Window Sensor WA 122 DW X1 Wired Mini Siren WA 207 S X 1 Rechargeable Battery for Console X1 Power Supply X1 Optional Accessories WA 117 W Panic watch emergency caller 12V WA 118 S Smoke Detector 9V WA 129 RC Key chain Remote Control WA 123 DW Door Window Detector 9V WA 124 DK Door keypad Detector 9V WA 125 G Gas Detector WA 126 EX Range extender with adapter WA 126 BAT Rechargeable Battery for WA 126 EX Planning for Installation M 4 eo Bs et z The security system is designed to be as flexible as possible in order to meet your present needs and also to adapt as your needs change For the reason we recommend that you read and consider the following information and plan your system before installing these devices Choosing Location It is important to try and place the Main Console in an area central to the alarm sensors This way all of the sensors can transmit signals with maximum efficiency The Main Console must be placed near a p
21. g the Panic Watch Transmitter Under Learning Mode to press the red button and the main console will sound beep to complete the setting successfully LCD display on the Main Console When trigger out the alarm system on emergency or the status of low battery the LCD display shown as below 63 Panic System 01 Help 63 Panic System 01 Low Battery 24 Smoke Detector This smoke detector is armed in 24 hours When it detects smoke it send a signal to the main console and an alarm is generated the internal sounder and auto dialer is activated If the smoke level decreases to a set limit the smoke detector will reset and go back to detecting status Notes Proper operation of the smoke detector can only be assured if the following instructions are followed and you should insure that the detector is NOT installed in the following areas 1 In kitchen an area where the smoke from cooking might cause an unwanted alarm 2 Near by ventilation fan flower essence lamps or deodorants or air conditioners as these can affect sensitivity of the detector 3 Near by ceiling beams or over the cabinets the stagnant air in these areas may affect the sensitivity of the detectors 4 In the peak of an A frame type of ceiling Powering up the detector 1 Remove the plastic cap 2 Put one 9V battery into the battery housing The Setting of the Smoke detector With the main console is Learning Mode press the Test button Smo
22. icrowave computer or light dimmer Where the effective range of the sensor is covered or blocked by furniture Where pets enter and exit freely for instance a cat or dog door Directly opposite any large object with flat reflecting properties like large windows or mirrors e In a bathroom or other area that is exposed to moisture and extreme temperature change Installing the PIR Motion Sensor Before installing the sensor consider the following points e Mount the sensor two meters 6 1 2 high for best coverage e Mount the sensor with a 14 degree downward incline angle against the wall for optimum range To install the PIR Motion Sensor please follow these steps 18 e Take out the screws or double sided adhesive and install the mounting bracket on the wall Press the ball joint portion into the bracket until it snaps securely Secure the mounting bracket on the wall 2 meters above the floor e Place the PIR sensor on the mounting bracket e Test the PIR sensor by walking within its range When the sensor is triggered the red LED light will flash once for 1 second LOWER LEVEL 4 ELEMENTS UPPER LEV 8 ELEMENTS Door Window Detector The magnetic Door Window detector is a contact sensor and should be applied on a door or window When the magnetic contact is opened broken or the battery is low the sensor will send out a message to the main console A message on the triggered sensor can be seen on the Main
23. in console 3 Remote Control handset Install the Battery and press the button The LED will light for 1 Sec The sensor will learn into the main console 4 Smoke Detector Install the Battery and press the button The LED will light for 1 Sec The sensor will learn into the main console 5 Gas Detector Plug in the AC power and press the TEST button The LED will light for 2 Sec The sensor will learn into the main console 6 When the sensor is learned into the main console it will show the message listed below It will automatically advance to the next sequencing learning order position 10 Sequential Pgming Sensor Added Sequential Pgming Trigger Sensor 02 7 fthe sensor that was learnt into the main console is sending a signal during the learning mode the main console will indicate on the LCD as shown below and will not allow duplication Sensor Already Exists in System 02 8 Ifthe sensor learned reachs 63 zone numbers the LCD panel will show a full message memory Sequential Pgming Mem Full 63 3 3 Replacement Menu When the sensor becomes faulty and needs to be replaced with a new one you will need to activate the menu To replace the original sensor key in the sequence learning order number and press ENTER Trigger the sensor and the new sensor will learn into the main console Note Please use the same type of sensor to replace the old one Press
24. ke and the main console will sound beep to indicate that it has completed the setting successfully 25 Installation for Smoke Detector 1 Mount the base portion of the unit firmly with the two screws provided to the ceiling where protection is required 2 Refit the top part of Smoke detector to the firmly mounted base according to the following figures Preferred Location N THE CENTER OF THE CEILING LCD display on the Main Console The detector will send an output a signal to the main console in the event of a fire or if a low battery output is detected the LCD display on the main console is shown as below Specifications 1 Detector sensor 2 Sensitivity 3 Operation temperature 4 Humidity 5 Low Battery 63 Smoke System 01 Zone Smoke System 01 Low Batt Photoelectric chamber Comply with UL 217 32 F 122 F 0 C 50 C Maximum 90 5 The main console unit emits two short beeps and LCD displaying MSG Please check battery power and replace it with new battery immediately 26 Door Keypad Detector This sensor is designed to detect arm and disarm doors Several functional operations are listed as below LEGEND 1 LED 2 NUMBER KEY 3 REED SWITCH 4 MAGN 5 TAMPER SV 6 BATTERY 7 BATTERY COVER Main Features 1 To Disarm Using a remote controller or keypad to arm the system enter password default 135246 and press C button o
25. ll only indicate the presence of gas at the sensor Gas may be present in other areas LCD display on the Main Console for Gas Detector When trigger out the alarm system on emergency the LCD display shown as below 63 Gas Detector 01 Zone Notes when activating When a gas leak is detected i e the Gas Detector has activated the alarm 1 Do not turn on any electrical appliance i e switch of light or any appliances that Can strike a spark until alarm sound automatically turn off 2 Turn off gas appliances or other sources of combustion at once furnace water heater gas burning stove or heater 30 3 Immediately get fresh air into premises 4 Fixthe gas source problem before restarting gas appliances Fire and Gas Safety Minimize fire risks around your home Common cause of household fires are smoking in bed cleaning or cooking with flammable liquids such as methylated spirits gasoline leaving children home alone and unsafe Christmas decorations Test your Smoke and Gas Detectors regularly Dust built up can seriously impair your detector s performance so remember to wipe it regularly checking batteries at the same time Check gas appliances regularly to ensure safe functioning Plan and practice an escape route Your Smoke Detector will warn you of danger but this wasted if you have not planned how to react to it When considering your alternative escape route and meeting place Remember that
26. maximum distance from a sensor back to the main console is 100 ft Mounting the Main Console The Main Console may be set on a table top or mounted on a wall To mount the console on a wall follow these steps 1 Remove the two top black rubber pads and store them away for future use 2 Measure and fix screws into the wall so that the two screws fit into the grooves left under the removed pads You may use the Installation Template on the last page of this Manual 3 Connect all wire connections to the jacks at the top of the console 4 Set the console onto the screws and carefully allow the console to drop into the groove securely About Passwords This system provides two sets of password for setting the system Install Master Install You can use this password to set the system such as telephone numbers or record message etc Master This password is used for setting Arm Arm away or Arm home Disarming the system etc When the system installation is finished family members will only need to Arm or Disarm the system Others We recommend that you install the console after programming the other wireless devices sensors into the main console This is to ensure that all of the wireless devices are working together properly Operation Main Console The Main Console is the heart of the security system It monitors the sensors and responds according to how it is programmed whenever a senso
27. message Press the CANCEL button to go back to the previous menu or to delete the Message Press ENTER to confirm program entry Key in the Master code then press the AWAY button to arm the system in the away mode Key in the Master code then press the HOME button to arm the system in the home mode To record Used to record messages 12 Power LED Indicates whether the AC Adaptor power is on or off 13 Armed LED When the light is on the system is armed When the light is off the system is disarmed 14 LCD Panel Displays messages 15 Speaker Sounds alarm and plays back messages 16 Antenna Used for wireless reception 17 Output Jack Connects to the external siren 18 Phone Jack Connects to the phone set 19 Line Jack Connect to the Telephone line from the wall 20 DC Power Jack DC supply input 3 0 Function for Installer Menu Factory Default Password 123456 1 Enter the password to start the menu setting as shown below Code kkkkkk i An incorrect password entered will show Access Denied and will emit a beep sound warning Access Denied ii If 3 incorrect passwords are entered the keyboard will become disabled and locked LCD shown below Try it again after one minute or use the Remote Control Handset button to unlock the system Note The remote control handset can be used to unlock the system however if It is not programmed into the
28. nal Powering up the Extender 1 To place a rechargeable battery WA 126 BAT into the battery house 2 To connect with AC adapter the power LED will light on 3 To select the extender mode In order to have the battery to work for full power it is needed about 72 hours at least to complete the charge The battery will work when AC power is in failure or disconnected Installation Locations In order to reach optimal transmitting efficiency it is extremely important to select a suitable location to mount range extender Also to mount in a position where wall electric outlet is accessible 1 Attach the screwing guidance label and fix screws on the wall It is recommended to mount the device about 6 feet 2 meters height from the floor and unable to be reached by children 2 Pull the antenna upward vertically to reach optimal transmitting range Transmitting test 1 First learned the remote control into Main Console to press the CHECK button on the main console and use remote control to arm the system through range extender 2 The efficient distance between sensors and range extender is about 30 meters 100 feet and between the Main Console and range extender is about 100 meters 300 feet 3 Range extender transmits the signal to the Main Console after 4 5 seconds receiving the signal from the sensor 4 Itis better to confirm the transmitting is OK after testing for 5 times Low Battery The backup battery
29. nd is activating the alarm 3 RESET TEST Button Press this button will activate the alarm with an audible sound Main Functions 1 Whenever the gas detector detects flammable gas up to 25 of lower explosive limits the red light and audio alarm sound will automatically turn on in 5 seconds When audio alarm sounds in this event you must at once follow the regular gas alarm procedure If the gas level reaches 10 of lower explosive limits the red light and audio alarm sound will automatically turn on in 20 seconds If the gas level reduces to 5 of lower explosive limits the red light and audio alarm 28 sound will automatically turn off in 5 seconds Lower explosive limits Natural gas methane 3 8 96 by volume in air standard 2 196 by volume in air standard Gas Alarm will activate before Natural gas methane 25 of lower explosive limits LP gas propane 25 of lower explosive limits Gas Alarm will activate before Natural gas methane 0 95 by volume in air LP gas propane 0 52 by volume in air Gas Alarm will activate in 0 95 by volume of Natural gas methane in air 5 seconds 0 52 by volume of LP gas propane in air 5 seconds Gas Alarm will activate in 0 2 by volume of Natural gas methane in air 20 seconds 0 1 by volume of LP gas propane in air 20 seconds Gas Natural gas methane Alarm will turn off at
30. om the magnet sensor It will trigger the sensor and the LED will light for 1 sec The Main Console will emit one Beep and the LCD will display Sensor Added The sensor has programmed into the main console successfully LCD display on the Main Console for Door Window Detector When the system is in armed mode Message shown on main console e Window opened Door opened 63 WINDOW SENSOR 63 DOOR SENSOR 01 Open 01 Open When the system is in the process of arming and the sensor has been opened prior to the arming Message shown on main console e Window opened 20 63 WINDOW SENSOR 01 Open Window battery cover opened Door battery cover opened 63 WINDOW SENSOR 63 DOOR SENSOR 01 Tamper 01 Tamper Installing the Door Window Detector Installing for DC 12V Detector To install a Door Window Detector follow these steps 1 Before installing the sensor ensure the sensor has programmed into the main console successfully 2 Apply double sided adhesive tape to the back of the sensor 3 Find the arrow embossed on the sensor just below the LED light Find a similar arrow on the magnet Before exposing the adhesive backing align the two arrows on the surface where you want them installed Check that both parts of the device fit and that they can be mounted with a gap less than 1 4 inch between them refer to the picture below 4 Reconfirm the setting on the main console Press the CHECK button and then open the window
31. ower outlet and telephone jack Setting Alarm Zones Before installation you should have the sensors programmed on the Main Console via the systems learning mode on the Main Console This system allows you to install a maximum of 63 wireless sensors Installing the Back up Battery Optional Accessory 1 Remove the battery cover at the back of the Main Console 2 Locate the connector plug and connect the rechargeable back up battery 8KR700 to this connector 3 Re install the battery cover Powering the Main Console 1 Attach the end of the adapter into the connector provided at the top of the console 2 Plug the AC adaptor into the power outlet 3 When the power is installed on the main console you will see the LCD shown below Welcome 00 HOME SECURITY Disarmed Connecting the Telephone Line To connect the Main Console to the telephone line Please follow these steps 1 Locate the two phone jacks at the top of the main console These phone jacks are marked Phone and Line 2 Connect one end of the telephone cord that came with the system into the connector labeled Line Connect the other end of that cord into the wall jack 3 Connect a telephone to the Main Console through the phone jack Note The system will only work with Touch Tone service Setting the Antenna Carefully extend the antenna upward in order to maximize the range of communication between the sensors and the Main console Remember that the
32. r is activated The illustration shown for the Main Console may look complex at first however most procedures are straightforward and easy Please review the illustration below which labels all the parts of the Main Console LCD Panel Illustration 3 we O gt cone e CA Eeee q4 s A I UA E SP DL CH 2 B a n E N OD 10 z 9 3 1 4 G ME G e occ s mm edd ze BB LT J G Ga LEGEND 1 NUMERIC AND BUTTONS 9 AWAY BUTTON 17 OUTPUT TERMINAL JACKS 2 BURGLARY BUTTON 10 HOME BUTTON 18 TELEPHONE JACKS 3 FIRE BUTTON 11 MIC 19 TELLINE JACK 4 MEDICAL EMERGENCY BUTTON 12 POWER LED INDICATOR 20 DC POWER JACK 5 SP DIAL BUTTON 13 ARMED LED INDICATOR 6 CHECK BUTTON 14 LCD PANEL 7 CANCEL BUTTON 15 SPEAKER 8 ENTER BUTTON 16 ANTENNA 1 Numeric keys and For telephone setting include the pound and star keys keys 2 Burglary Button 3 Fire Button 4 Medical Emergency 5 SP DIAL button 6 Check 7T Cancel 8 Enter 9 Away 10 Home 11 Mic Press the SP DIAL amp Burglary Buttons together Press the SP DIAL amp Fire Buttons together Press the SP DIAL amp Fire Buttons together Press the SP DIAL button together with 4 5 or 6 to activate one of the 3 emergency dialing numbers Press the CHECK button to review sensor settings and to check recorded
33. r use keypad to arm the system and enter password default 135246 no need to press C button 2 To Arm Away enter password default 135246 and LED lights on then press E button it will have a long beep sound and LED will extinguish after flashing 30 times 3 To Arm Home enter password default 135246 and LED lights on then press 0 button it will have a long beep sound and LED will extinguish after flashing 30 times 4 To change password enter existing password default 135246 if the password is correct and LED will light on then press 3 button and enter 6 digits of number any 0 9 as a new password After the existing password a long beep to confirm correct password is entered 3 short beep indicates wrong password is entered 27 If enter number less than 6 digits ex 11111 then press E button afterwards to tell the end another long beep is sounded to indicate new password is programmed If you use the password number less than 6 digits ex 11111 you need to enter 11111 and press E to finish password confirmation Itis suggested to set the password as same as Master Code on the main console Gas Detector Armed in 24 hour status and designed to detect either city gas methane or LPG propane and butane 1 Power Green LED When AC plug in and the green LED light up constantly 2 Alarm Red LED If the red LED lights on the sensor has detected a gas leak a
34. rogramming menu Even if the PIR Motion Detector is triggered and the main console is armed in the HOME mode the main console will neglect the PIR signal 63 REMOTE SENSOR 01 Panic PIR Motion Detector You can move freely within your house without triggering the alarm mu 2 POWER SWITCH CNOFFNW 3 DETECTING SENSITIVITY SWITCH 4 BATTERY 9 ROCKER ARM amp HOLDER 6 BATTERY COVER Main Features 1 2 oot LED When the PIR has detected any human movement the red LED will blink for One sec This means its transmitting out a signal to the Main Console When the battery power becomes low it will send out a low battery message and the red LED will blink for one second If the Main Console receives this message it will leave a message on the display C OFF W SWITCH i When the switch is set to C Continue position the PIR sensor will continually detect movement at a 3 to 5 second interval ii When the switch is set to the OFF position the power is turned OFF and the PIR sensor will not work iii When the switch is set to the W Wait position the PIR sensor will detect movement at a 2 to 3 minute interval This is to conserve battery power DETECTING SENSITIVITY 1 2 4 select the sensor for high medium or low sensitivity BATTERY Remove the Battery cover and insert one 9V alkaline battery ARM amp HOLDER For mounting on the wall BATTERY COVER 17 Replace the Battery
35. todial order is Preset 5 gt Preset 1 Preset 2 gt Preset 3 Fire condition e 6 the autodial order is Preset 6 gt Preset 1 Preset 2 gt Preset 3 Medical help condition Arm or Disarm Via the Telephone Line for Tone Mode This function allows you to dial your home telephone from outside and remotely control change the arm disarm status of your security system When you hear a long Beep sound after 10 rings on the phone enter the Master code 135246 default If the password is correct the system will respond with a long Beep sound if the password is less than 6 digits you will need to enter the button to finish the password entry One Beep sound indicates that the system is in the Armed Away mode Two Beep sound indicates it s in the Armed Home mode Three Beep sound indicates that the system is Disarmed You can now key in 1 2 or 3 to change the status The Main console will respond to the relative message as listed below Response message as listed below e Pressing 1 indicates that the system is Armed Away You will hear one Beep sound through the phone e Pressing 2 indicates that the system is Armed Home You will hear two Beep sounds through the phone e Pressing indicates that the system is Disarmed You will hear three Beep sounds through the phone If the system has been programmed in the Armed Away or
36. y 10 Sec to remind you of this The first 5 messages can be displayed on the LCD If you want to check or delete the MSG the system will need to be in the disarm mode The LCD display is shown below 00 HOME SECURITY Disarmed MSG Press the ENTER button to read the message Press the ENTER button again to read the next message etc 63 DOOR SENSOR 01 Open Press the CANCEL button to delete all MSG s The LCD display is shown below MESSAGE DELETED 24 Hour amp Home Away Functions 24 Hour Mode This security system can work for you 24 hours a day 7 days a week The system features a 24 hour status capability which is important for use with some accessory sensors The sensors that belong to the 24 hour mode include the Smoke Detector Gas Detector and Remote Control Handset PANIC button A AWAY and H HOME modes When the system is armed in the HOME mode the Main Console will exclude all PIR Detectors so the user can move freely within the house without triggering the PIR Motion Detector When the system is armed in the AWAY mode all sensors programmed are active and are ready to trigger the alarm 15 Remote Control Handset The key chain Remote Control Handset is a convenient way to arm Home Away mode or disarm this system Before using this device please program it into the main console via the sequence programming menu AWAY HOME v PANIC DISARM LEGEND 1 TRANSMIT LED 2 DISARM K
Download Pdf Manuals
Related Search
WA 1100 K wa1200 komatsu 1100 s blueberry pl kennewick wa 99338