Commercial Level 1 PowerPost™ EVSE Installation & User Manual
Contents
1. 14 Removing Electronics Module 15 Input Power Fuse 4442 2 22244 15 Electronics Module 24 4 ney 16 Cord Reel amp Cable Assembly nennen nne 17 LIMITED WARRANTY AND EXCLUSIONS 2 2 2 2 21112 18 COMPLAN CE ee A eee a ee ele tala eee eee 19 SPECIFICATIONS GUY LL YF FU 19 Mechanical GDG GN pa 19 Electrical seiadu dd GN iN nd y DF i TU ND 19 OUT PIE SH FERRY NN HE FU RHEON FFF NEN EFE FEE FFURF FFWR 19 PATENTS ET FY TH HR Y A a E Eaa ea E aaa aaa aiaa 19 Ste aN a E T A 19 Symbols and Important Safety Messages Used on this Manual This symbol precedes a Warning a Caution or Important message This symbol means there is a risk of electric shock and precedes a Warning Caution or statement related to wiring WARNING Indicates a potentially hazardous situation that can result in serious injury or death if it is not avoided CAUTION Indicates a situation that can damage equipment and possibly result in injury IMPORTANT Indicates critical information pertaining to local codes installation or operation of the equipment IMPORTANT SAFETY INSTR2. gp 9 0 7 0 Figure 1 L1 PowerPost EVSE Footprint amp Mounting Hole Locations L1 PowerPost EVSE Installation amp User Manual Page 3 INSTALLATION TEMPLATE UT ALGNGTHISLINE I L1 PowerPost EVSE Installation amp User Manual Page THIS PAGE IS INTENTIONALLY LEFT BLANK L1 PowerPost EVSE Installation amp User Manual Page 5 Installation Procedure 1 Ensure supply power to the charging station is interrupted and properly locked out 2 Remove L1 PowerPost EVSE from packaging 3 Pull charge coupler and cable out completely approximately 14 feet until last ratchet stop of cord reel See Figure 2 N WARNING Pulling charging cable out of the L1 PowerPost EVSE with excessive force when Charge station is not stable can result in damage to the Coupler unit or injury Figure 2 Charge cable extended 4 Remove 4 screws that attach the top cover to the charging base use security bit provided Retain screws for later installation 7 2 h Gently lift the top cover 6 inches See Figure 3 Disconnect H LED cable harness connector from charging base harness by pressing release tab and pulling gently apart See Figure 4 Figure 3 Top Cover Removed Figure 4 LED cable harness connector L1 PowerPost EVSE Installation amp User Manual Page 6 Installation Procedure continued 5 Remove 6 screws in the lower front and sides of the
3. telefonix POWER Post n Commercial Level 1 PowerPost EVSE Installation amp User Manual Document 906 041 Revision B 01 14 2014 Contents IMPORTANT SAFETY INSTRUCTIONS PLEASE 1 lt eet eee eee 2 Tools amp Materials Required for 1 254 11 2 Electrical Requirements soseri ces faeces ROSE nais 3 Mechanical requirements 3 Installation Unig iyd GO GSG UR GU MS FUN US ctwuiecesetevecestvoevuscdusaeress 4 Installati n 2 CAAA E FAYN ENNNR G LLON 6 OPERATION Y Ga Gu ddd EN GG 9 Stat s l dicator esson adne dsini en ataia ensi 10 Initial POW FU FFF FFF FF NF FAN HEFFER NEF HF HEFFER 10 Cable Extension amp Vehicle 44 222 42 2 10 Vehicle Disconnection amp Cable Retraction nnmnnn nnne 11 TROUBLESHOOTING ore 12 CLEANING oo yok tse ene devon 14 SERVICE REPAIR
4. L1 PowerPost EVSE Installation amp User Manual Page 19 SOFTWARE continued The CONSOLE_ 2340 program is modified by Telefonix as of 2013 using Open EVSE and is released as licensed under the GPLv3 License CONSOLE_ 2340 is free software you can redistribute it and or modify it under the terms of the GNU General Public License as published by the Free Software Foundation under version 3 of the License which may be viewed at http www gnu org licenses gpl html This program is distributed in the hope that it will be useful but WITHOUT ANY WARRANTY without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE See the GNU General Public License for more details No licenses for any patents trademarks or trade secrets related to the L1 Power Post or any other hardware or systems however is granted hereunder Telefonix will upon reguest make available a schematic pursuant to the Creative Commons Public License version 3 0 the CCPL available at http creativecommons org licenses by sa 3 0 legalcode Such schematics detail enhancements provided by Telefonix and such Telefonix schematics use among other sources EVSE power supply schematics provided by Open EVSE and available at https code google com p open evse No connection with sponsorship warranties or endorsement by Open EVSE or its members of such schematics of Telefonix or its use any works is asserted or implied hereunder Any T
5. charging port must be within approximately 10 12 feet of charging station to reach safely Gently plug the charge coupler into the vehicle connector until the latch Clicks and locks the two pieces together The charge coupler must be fully seated in the vehicle connector L1 PowerPost EVSE Installation amp User Manual Page 10 Cable Extension amp Vehicle Connection continued e TheL1 PowerPost EVSE will automatically determine the status of the vehicle and begin charging The blue Charging light will illuminate If the vehicle does not demand charging power the amber Connected light will illuminate lf the vehicle requires charging but is not yet ready to accept current the amber Connected light will flash Charging will begin automatically when the vehicle signals that it is ready and the blue Charging light will illuminate Ifthe L1 PowerPost EVSE detects a ground fault condition upon connection to the vehicle the red Out of Service light will illuminate and charging power will be interrupted until the plug is removed The unit will re enable charging after a 2 minute interval 1 the L1 PowerPost EVSE detects a ground fault condition in the middle of charging the red Out of Service light will illuminate and charging power will be interrupted The unit will re attempt charging after a 10 second interval Vehicle Disconnection amp Cable Retraction Grasp charge c
6. meet SAE standard J1772 Use of the product for any other application can damage the L1 PowerPost EVSE and or the vehicle Do not use the L1 PowerPost EVSE if the cable is frayed or the insulation is damaged Do not use the L1 PowerPost EVSE if the case has been severely damaged Tools amp Materials Reguired for Installation 4 Security Hex Bit supplied with unit 2 Philips Screwdriver Bubble Level or equivalent Wire stripper 10 12 AWG Crescent Wrench for tightening installer supplied attachment hardware Concrete anchors P N Hilti HLC HX 304SS 3 8 x 3 or equivalent Attachment hardware with tensile strength of 450 Ibs or stronger Example 4x 3 8 nuts 4x 3 8 fender washers 4x 3 8 lock washers Conduit attachment flange if using rear conduit entry L1 PowerPost EVSE Installation amp User Manual Page 2 Electrical Requirements Circuit Protection Dedicated 120V 50 60Hz 20A circuit Conduit Cable Penetration Electrical supply cable can enter from the back or from the bottom of the unit Supply wire size 12 AWG min 75 C Copper wire Conduit height from ground 24 inch Max Min height per state and local codes Free cable length 52 inch Min length beyond end of conduit Mechanical requirements Four concrete anchors with tensile strength of 450 Ibs or more See Figure 1 for spacing Mounting surface that can support pressure loads of 2000 PSI or more 6 5 9
7. Terminate Line Neutral and Ground wires per Figure 7 N IMPORTANT Torque line termination screws Li A Neutral 20 inch pounds i Line 10 Install the 6 screws in the lower front and sides of the unit that attach the front housing to the charging base See Figure 6 Electrical Supply Lines Grommet USE CONDUCTORS ONLY A IMPORTANT Torque screws to 15 20 in lbs 11 Carefully position front housing on charging Figure 7 Input Wiring Termination base Install the 12 screws in the back of the unit that attach the front housing to the charging base A IMPORTANT Torque screws to 15 20 in lbs Re connect LED cable harness connector to charging base harness Gently place the top cover on the charging base making sure not to pinch the LED cable harness Install the 4 screws that attach the top cover to the charging base N IMPORTANT Use hand tools on step 12 to avoid cracking of unit Torgue screws to 15 20 in lbs Return the charging cable to the cord reel by pulling cable approximately 1 2 inch to allow cable to retract into L1 PowerPost EVSE Place charging coupler into connector storage receptacle See Figure 8 Figure 8 Completed Installation L1 PowerPost EVSE Installation amp User Manual Page 8 Installation Procedure continued 14 Restore supply power to the L1 PowerPost EVSE This will initiate a self test and the status lights may flash The green Sta
8. UCTIONS PLEASE READ SAVE THESE INSTRUCTIONS A WARNING When using electric products basic precautions should always be followed including the following e Read all the instructions before using the L1 PowerPost EVSE by Telefonix This device should be supervised when used around children Do not put fingers into charge coupler or vehicle connector Do not use the L1 PowerPost EVSE if the flexible power cord or EV cable are frayed have broken insulation or any other signs of damage Do not use the L1 PowerPost EVSE if the enclosure or the charge coupler is broken cracked open or shows any other indication of damage Charge coupler is not intended for current interrupting Do not operate the L1 PowerPost EVSE in temperatures below 22 F 30 C or above 122 F 50 C Do not install the L1 PowerPost EVSE in close proximity to combustible materials or flammable vapors WARNING CORD REEL ASSEMBLY Do not disassemble the cord reel assembly in the L1 PowerPost EVSE Failure to heed this warning can result in serious injury or death Due to the high tension power spring inside the assembly the cord reel should only be serviced by Telefonix Inc GROUNDING INSTRUCTIONS This product must be connected to a grounded metal permanent wiring system or an equipment grounding conductor must be run with the circuit conductors and connected to the equipment grounding terminal or lead on the pr
9. an the L1 PowerPost EVSE with a damp cloth and mild detergent Do not use high pressure water to clean the L1 PowerPost EVSE Do not use solvents that may damage the finish or plastics of the L1 PowerPost EVSE SERVICE REPAIR Other than periodic cleaning the L1 PowerPost EVSE does not require any maintenance The input power fuse can be replaced in the field if necessary The electronics module assembly and the cord reel cable assembly are each Line Replaceable Units LRU that can be removed and replaced in the field These two assemblies can only be field replaced with a certified LRU assembly only available directly from Telefonix or authorized distributors For any other damage or failures contact Telefonix Technical Support L1 PowerPost EVSE Installation amp User Manual Page 14 SERVICE REPAIR continued Removing Electronics Module Cover 1 Remove the two 2 black ferrite beads on the braided LED cable by opening plastic clamp in center of the bead see Figure 11 and Figure 12 below Ferrite Beads Figure 13 Figure 11 Figure 12 2 Remove metallic tape on bottom of the cover see Figure 13 above The tape on top of the cover can be left in place 3 Remove the bottom cover piece and slide cover up and off of the Electronics Module Input Power Fuse Replacement 4 Interrupt power to the L1 PowerPost EVSE and lock out as appropriate 5 Disassemble unit per steps 3 5 in the Installation sec
10. e L1 PowerPost EVSE DOES begin charging Disassemble unit per steps 3 5 above vehicle when charge coupler is plugged in Verify that LED cable harness connector is securely mated to charging base harness If these steps do not resolve the problem contact Telefonix technical support Interrupt power to the L1 PowerPost Station Available light illuminated but L1 EVSE and lock out as appropriate PowerPost EVSE does not begin charging Disassemble unit per steps 3 5 above vehicle when charge coupler is plugged in Verify that output power wiring is securely terminated to cord reel terminal block If possible plug the L1 PowerPost EVSE into a different vehicle If these steps do not resolve the problem contact technical support L1 PowerPost EVSE Installation amp User Manual Page 12 TROUBLESHOOTING continued Corrective Action This occurs when a successful connection Connected light illuminates or flashes as soon to the vehicle is made but the vehicle is not as vehicle is connected demanding charging current Verify that vehicle batteries are not already fully charged Verify that vehicle is set for immediate charging and is not set for delayed or timer charging Verify that vehicle electronics are not being cooled If cooling system is running wait until cooling stops When cooling is complete the vehicle should automatically signal for charging and the blue Charging light will
11. elefonix copyrights related to such schematics may be used pursuant to the rights and obligations of the CCPL which may be viewed at the link provided above Nothing under this agreement however shall provide rights to any Telefonix trademarks patents or trade secrets all such rights being reserved L1 PowerPost EVSE Installation amp User Manual Page 20 CONTACT INFORMATION Contact Telefonix Inc for customer service technical support and warranty claims For information about the Telefonix L1PowerPost visit www L1PowerPost com telefonix 2340 Ernie Krueger Circle Waukegan IL 60087 Phone 847 244 4500 Fax 847 244 4525 www telefonixinc com Designed Engineered and Manufactured in the U S A Copyright 2013 Telefonix Inc All Rights Reserved Telefonix is a registered trademark of Telefonix Inc L1 PowerPost is a trademark of Telefonix Inc L1 PowerPost EVSE Installation amp User Manual Page 21
12. illuminate If these steps do not resolve the problem contact Telefonix technical support Wait 2 minutes to see if the L1 Out of Service light is illuminated before vehicle PowerPost EVSE returns to normal is connected Station Available indication It may be ina ground fault timeout from previous use Remove power to the L1 PowerPost EVSE for at least 30 seconds Restore power to the L1 PowerPost EVSE If these steps do not resolve the problem contact Telefonix technical support L1 PowerPost EVSE Installation amp User Manual Page 13 TROUBLESHOOTING continued Corrective Action e lf Out of Service light does not extinguish Out of Service light illuminates when vehicle is after 1 minute verify that the L1 connected PowerPost EVSE is properly grounded Remove charging connector from vehicle If Out of Service light extinguishes the vehicle batteries may be overheated Allow vehicle batteries to cool and try charging again If Out of Service light does not extinguish the L1 PowerPost EVSE has detected a ground fault with the vehicle Wait 2 minutes for the GFI circuit to reset and then try charging again If the L1 PowerPost EVSE trips again have the vehicle checked If these steps do not resolve the problem contact Telefonix technical support CLEANING Always interrupt power supply to the L1 PowerPost EVSE before cleaning Cle
13. ing charged by the L1 PowerPost EVSE Connected Solid Amber Indicates a vehicle is connected but not charging at this time This typically occurs because the vehicle is fully charged Connected Awaiting Charging Signal Blinking Amber Indicates a vehicle is connected and requires charging but the vehicle has not yet signaled that it is ready to begin charging This usually occurs when the vehicle electronics are cooling and have not reached the temperature required for charging Out of Service Red Indicates a problem with the L1 PowerPost EVSE or the connected plug in vehicle Refer to the Troubleshooting section for diagnosis Initial Power Up When supply power is applied to the L1 PowerPost it will perform a brief self test During this test the status lights may flash including the Out of Service light This is normal Within a few seconds the green Station Available light will illuminate If there is a problem the Red Out of Service light will illuminate Cable Extension amp Vehicle Connection Grasp stowed charge coupler and press handle release button with thumb Gently and smoothly pull coupler and cable out of charging station base When desired length is reached allow cable to rewind slightly to nearest ratchet stop The cable ratchet will engage at approximately 8 inch intervals N CAUTION Do not attempt to over extend cable beyond 14 feet Damage to the unit may result Vehicle
14. ion L1 PowerPost EVSE Installation amp User Manual Page 16 Cord Reel amp Cable Assembly Replacement WARNING DO NOT DISASSEMBLE THE CORD REEL The high tension power springs inside the cord reel assembly can cause serious injury or death The L1 PowerPost EVSE cord reel assembly should only be serviced by Telefonix Inc at a certified Telefonix facility 1 Interrupt power to the L1 PowerPost EVSE and lock out as appropriate 2 Disassemble the L1 PowerPost EVSE per steps 3 5 in the Installation section 3 Remove the 8 Phillips head screws from the metal retaining flange attaching the front bezel to the front housing see Figure 16 Retain the screws for later re installation Remove the retaining flange and pull the plastic bezel forward off the housing RETAINING FLANGE BEZEL CABLE GUARD Figure 16 Front Bezel Rear View Figure 17 Front Bezel Disassembled 4 Remove the 2 Phillips head screws attaching the lower cable guard to the bezel Retain the screws for later re installation Remove the cable guard from the bezel see Figure 17 5 Slide the charging cable down out of the cable slot in the bezel Feed the cable through the large opening in the front housing and through the bezel retaining flange to free it from the housing L1 PowerPost EVSE Installation amp User Manual Page 17 Cord Reel amp Cable Assembly Replacement continued 6 Disconnect the cord reel wiring from the terminal b
15. ited to one year Telefonix is not liable for incidental indirect special or consequential damages including without limitation damage to or loss of use of any equipment lost sales or profits or delay or failure to perform this warranty obligation The remedies provided herein are the exclusive remedies under this warranty whether based on contract tort or otherwise The warranty is to the original owner only and is not transferable COMPLIANCE SAE J1772 UL Listed Electric Vehicle Charging Station E359477 NEMA SPECIFICATIONS Mechanical Dimensions 59 High x 6 Wide x 9 Deep 16 with stowed Charge Coupler Weight 40 Ibs Charging Cable Length 14 Retractable Operating Temperature 30 C to 50 C 22 F to 122 F Waterproof Rating UL 50E Type 3R Rating Electrical Input Power 110 120 VAC Single Phase 50 60Hz 16A Max Current Draw Output Power 120VAC 60 Hz 16A Max Standby Power Consumption 5W 40 mA 120V Surge Suppression 7000A 360V Max Ground Fault Sensitivity 20mA OTHER PATENTS The Electrical Cord Reel Assembly ECR used in the L1 Power Post Electrical Vehicle Charging station is covered by US 8 387 763 B2 as well as additional patents pending Aspects of the L1 Power Post Electrical Vehicle Charging station are the subject of patents pending SOFTWARE An executable copy of the CONSOLE_ 2340 program is provided with the L1 Power Post hardware system
16. lock see Figure 15 page 17 7 Remove the 2 large Philips head screws washers and lock nuts holding the cord reel in place Retain the hardware for later re installation Carefully remove the cord reel amp cable assembly from the L1 PowerPost EVSE 8 Carefully install the new cord reel amp cable assembly using the 2 Phillips head screws and lock nuts Torque lock nuts to 10 in lbs Do not over tighten lock nuts or you may damage the cord reel 9 Reconnect the cord reel wiring to the terminal block per Figure 12 on page 17 10 Feed the charging cable through the bezel retaining flange and through the large opening in the front housing Slide the charging cable up and into the cable slot in the plastic front bezel 11 Reinstall the lower cable guard into the bezel Reinstall the 2 Phillips head screws attaching the lower cable guard to the bezel Torque screws to 10 in lbs Do not over tighten screws or you may damage the plastic See Figure 17 page 18 12 Place the plastic bezel onto the front housing Install the retaining flange behind the bezel and install the 8 Phillips head screws in the metal retaining flange Torque screws to 10 in lbs Do not over tighten screws or you may damage the plastic See Figure 16 13 Re assemble the L1 PowerPost EVSE per steps 10 14 in the Installation section LIMITED WARRANTY AND EXCLUSIONS Telefonix warrants to the original purchaser and not for the benefit of anyone else that this p
17. oduct N CAUTION The L1 PowerPost is intended for use with vehicles conforming to Society of Automotive Engineers SAE standard J1772 Using it for any other applications can damage the L1 PowerPost EVSE and or the nonconforming vehicle L1 PowerPost EVSE Installation amp User Manual Page 1 INSTALLATION 2 IMPORTANT Check with state and local authorities to ensure compliance with codes and ordinances before starting installation The L1 PowerPost EVSE must be installed by a licensed electrician This device shall be mounted at a sufficient height from grade such that the height of the storage means for the coupling device is located between 450 mm 18 inches and 1 2 m 4 feet from grade WARNING The L1 PowerPost EVSE must be connected to a grounded metal permanent wiring system or an equipment grounding conductor must be run with the circuit conductors and connected to the equipment grounding terminal or lead on the product To reduce the risk of fire connect only to a circuit provided with 20 amperes maximum branch circuit over current protection in accordance with the National Electrical Code ANSI NFPA 70 Always interrupt the power supply to the L1 PowerPost EVSE before opening the case Never insert anything fingers tools etc into the L1 PowerPost EVSE charge coupler The L1 PowerPost EVSE is designed for use with plug in vehicles equipped with vehicle connectors that
18. oupler and press handle release button with thumb Gently and smoothly pull charge coupler out of vehicle connector To retract charging cable pull cable straight out of charging station approximately half an inch to release retraction ratchet Then allow cable to retract into charging station base N CAUTION Do not allow cable to retract in a rapid uncontrolled manner When cable is fully retracted insert charge coupler into storage port on charging base L1 PowerPost EVSE Installation amp User Manual Page 11 TROUBLESHOOTING Corrective Action e Interrupt power to the L1 PowerPost None of the status lights are illuminated L1 EVSE and lock out as appropriate PowerPost EVSE does NOT charge vehicle Disassemble unit per steps 3 5 above when charge coupler is plugged in Restore supply power to L1 PowerPost EVSE Verify that proper supply voltage is present at the L1 PowerPost EVSE terminal block See Figure 7 Interrupt power to the L1 PowerPost EVSE and lock out as appropriate Verify that supply power wiring is securely terminated to incoming power terminal block Interrupt power to the L1 PowerPost EVSE and lock out as appropriate Remove incoming power fuse and verify continuity Replace fuse if blown If these steps do not resolve the problem contact Telefonix technical support Interrupt power to the L1 PowerPost None of the status lights are illuminated EVSE and lock out as appropriat
19. roduct is free of defects in materials and workmanship under normal and proper use for the following warranty periods a For the Cord Reel assembly 18 months from the purchase date b For all other components 36 months from the purchase date If a part fails due to defect during the applicable warranty period Telefonix will provide at no charge a new or remanufactured part at Telefonix s option and that is Telefonix s exclusive obligation under this warranty for a product failure This warranty does not cover labor or other costs incurred to diagnose repair remove install ship service or handle defective or replacement parts or for removal or reinstallation of the product This warranty is void if this product is installed improperly or in an improper environment overloaded misused abused or altered in any manner or is not used and properly maintained under normal operating conditions or not in accordance with any labels or instructions This warranty does not cover damage caused by electrical spikes power surge or lightning L1 PowerPost EVSE Installation amp User Manual Page 18 Limited Warrant and Exclusions continued There are no other or implied warranties of any kind including merchantability and fitness for a particular purpose but if any implied warranty is required by the applicable jurisdiction the duration of any such implied warranty including merchantability and fitness for a particular purpose is lim
20. tion N 6 Remove Electronics Module cover see instructions above page 16 7 Remove and replace fuse with Littlefuse P N ONLNO20 T See Figure 11 WARNING DO NOT USE ANY OTHER FUSE RATING 1 Figure 14 Power Fuse Damage to the L1 PowerPost EVSE or serious injury could result L1 PowerPost EVSE Installation amp User Manual Page 15 Electronics Module Replacement 1 Interrupt power to the L1 PowerPost EVSE and lock out as appropriate 2 Disassemble the L1 PowerPost EVSE per steps 3 5 in the Installation section 3 Remove Electronics Module cover see instructions on page 16 4 Disconnect the supply wiring and cord reel wiring from their respective terminal blocks See Figure 7 in the Installation section 5 Remove the 4 Philips head screws holding the Electronics Module in place and remove the module from the chassis Retain the screws for later re installation 6 Install the new Electronics Module using the 4 Phillips head screws Torque screws to 8 in lbs 7 Reconnect the cord reel wiring to the terminal block per Figure 15 Green tf Black Red Orange Figure 15 Cord Reel Wiring Termination 8 Reconnect the supply wiring to the terminal block per Figure 7 in the Installation section 9 Reinstall Electronics Module Cover using the Removing Electronics Module Cover steps found on page 16 in reverse 10 Reassemble the L1 PowerPost EVSE per steps 10 14 in the Installation sect
21. tion Available indicator light will remain illuminated See Figure 9 If red Out Of Service indicator stays illuminated refer to Troubleshooting section See Figure 10 teletonix teletonix POWER fl POWER s Figure 9 Station Available Figure 10 Out of Service OPERATION WARNING The L1 PowerPost EVSE is designed for use with plug in vehicles equipped with vehicle connectors that meet SAE standard J1772 Use of the product for any other application can damage the L1 PowerPost EVSE and or the vehicle Never insert anything fingers tools etc into the L1 PowerPost EVSE charge coupler Always retract charging cable pull cable to stow when the L1 PowerPost EVSE is not in use to reduce cable damage and tripping hazards Do not leave connector lying on the ground Do not use the L1 PowerPost EVSE in close proximity to combustible materials or in the presence of flammable vapors Do not use the L1 PowerPost EVSE if the cable is frayed or the insulation is damaged Do not use the L1 PowerPost EVSE if the case has been visibly damaged crushed or is not properly secured to the mounting base L1 PowerPost EVSE Installation amp User Manual Page 9 OPERATION continued Status Indicator Lights Station Available Green Indicates the L1 PowerPost EVSE has power and is ready to charge a vehicle Charging Blue Indicates a vehicle is currently connected and is be
22. unit that attach the front housing to the charging base Remove 12 screws in the back of the unit that attach the front housing to the charging base Retain screws for later installation Gently lift the front housing 2 inch and slide forward and out of the way See Figure 5 6 Place provided template see Page 4 on concrete surface that the L1 PowerPost EVSE will be mounted to Drill 4 holes in locations provided in template RAE NRE SAU As 7 Install charging base over pre drilled holes in concrete Shim as necessary to level unit Install concrete anchors as specified by manufacturer Figure 5 Front Housing Removed N IMPORTANT Torgue fasteners to concrete anchor manufacturer s recommended torgue value See Figure 6 Detail A 2 LOCATIONS FOR ELECTRICAL STUD 4 MOUNTING LOCATIONS SEE DETAIL A TO BE SET INTO CONCRETE DETAIL A Figure 4 LED cable harness connector L1 PowerPost EVSE Installation amp User Manual Page 7 Installation Procedure continued 8 Feed electrical supply through either rear or bottom entry location on left of unit If rear entry is used secure conduit to rear housing with appropriate hardware Feed wires from left to right of unit through bottom rear wire access hole Route cable upwards and feed from right to left of unit through cable pass through grommet between cord reel and circuit board See Figure 6 on previous page and Figure 7 below 9
Download Pdf Manuals
Related Search