User Manual - RhinoCo Technology
Contents
1. If this featured is turned on then a single beep will be produced If this feature is turned off then no beeps will be heard When this feature is turned on then the Transformer module may be interfaced to allow the user to arm and disarm their vehicle via the factory remote control NOTE If the Transformer module was supplied with the unit then this feature would have been turned ON by default If this featured is turned on then a single beep will be produced If this feature is turned off then no beeps will be heard 10 How to Change REGISTER 2 Vehicle Set Up DRIVER S DOOR OPEN AND THE IGNITION TURNED ON LAST Remote Key action TURN ON OFF FEATURES VIA THE LEFT BUTTON ON THE REMOTE FEATURE Press Remote This Many Times Centre button disabled 1 LEFT Button Used To 2 Arm Disarm This Vehicle Impact Sensor 3 Automatic Rearm Relock 4 Timed Negative on Arm 5 Headlight Timer 15 sec Selectable Indicator Flash 6 Extended Lock Pulse Central 7 Closure Extended Unlock Pulse 8 Override Code 14 FACTOR Y SETTIN DESCRIPTION Stop button centre button from arming and disarming not normally used This is activated if you have two cars with Rhino remote controls the vehicle that this is feature is activated on will use the left button to arm disarm and loose the ability to activate the boot release output This feature prevents accidental system disarming amp will relock the doo2. g f NS way SO LOO RA K E Proudly Designed LEADING THE CHARGE in Australia AUSTRALIAN STANDARDS APPROVED N517 REMOTE CONTROL ENGINE IMMOBILISER AND ALARM WITH WIRELESS KEYPAD This product complies with AS NZS 3749 1 2003 Class A Volumetric Sensing must be enabled to comply with a Class A installation refer feature programming Class A VSAS Vehicle security alarm system includes control equipment including setting and unsetting facilities all sensors warning devices and provisions for immobilization of the vehicle and the volumetric sensing device glass break shock This product complies with AS NZS 3749 1 2003 Class B Volumetric Sensing must remain disabled to comply with a Class B installation refer feature programming Class B VSAS Vehicle security alarm system includes control equipment including setting and unsetting facilities all sensors warning devices and provisions for immobilization of the vehicle This product complies with AS NZS 4601 1999 Amdt 1 2003 This product is to be installed in accordance with the methods amp principles detailed in AS 3749 2 1997 Has your insurer specified fitting a RES2001 For details please refer to page 12 Instruction Manual e Thank you for purchasing a Rhino Engine Immobiliser Please read this manual carefully before commencing installation and keep it in a safe place for future reference Contents Contents ta e aba ee o o
3. APAGER Part No TRANS TX Part No WKPB PA AS AS ee ee Detailed Feature Descriptions Auto Immobilise The immobiliser will always automatically activate 38 seconds after the ignition is turned off no matter what The dash mounted LED will come on constantly to confirm the system has entered auto immobilise mode The vehicle cannot be started now unless the remote is pressed first When disarming if you do not switch the ignition on within 38 seconds the immobiliser will also enter auto immobilise mode again If you take longer than 38 seconds to exit your car press the remote thinking you are locking it in fact you will actually be just turning the immobiliser off temporarily 8 leaving your car unlocked You must in this instance press your remote a second time to lock your vehicle Automatic re arm amp relock Programmable This feature prevents accidental disarming by the owner e the owner turns the immobiliser off but is then distracted and forgets that they have deactivated the system If a door is not opened or ignition turned on within 60 seconds from when the system is turned off by the remote the system will fully re arm amp re lock the vehicle Note The immobiliser will enter auto immobilise mode after 38 seconds the LED will come on constantly to indicate the vehicle is immobilised At the 60 second mark the system will fully arm amp the doors will lock the blinkers will flash once amp the siren will beep on
4. Company shall have no liability for any personal injury property damage or other loss based on a claim the product failed to give any warning However if The Company is held liable whether directly or indirectly for any loss or damage arising under this limited warranty or otherwise regard less of cause or origin The Company s maximum liability shall not in any case exceed the purchase price of the product which shall be the complete and exclusive remedy against The Company This warranty replaces any previous warranties and is the only warranty made by The Company on this product No increase or alteration written or verbal of the obligations of this Limited Warranty is authorised 19 TECHNOLOGY LEADING THE CHARGE 20
5. Sense Override Wireless Keypad Mode Transformer Interface SELECT to replay memory ON oF i SORE After pressing the remote 13 times to enter this mode turn the ignition off Your Rhino Alarm offers a unique memory that stores the ten last reasons why the alarm was triggered This memory cannot be erased 1 Beep 1 Flash Voltage Drop Alarm 2 Beep 2 Flashes Glass Break Alarm 3 Beep 3 Flashes Shock Sensor Alarm 4 Beep 4 Flashes Power Fail Alarm 5 Beep 5 Flashes Ignition Alarm 6 Beep 6 Flashes Aux Alarm 7 Beep 7 Flashes Door Alarms 8 Beep 8 Flashes Bonnet Boot Alarm If two previous alarms were recorded i e voltage drop and shock sensor the LED will flash and the siren will beep once for voltage drop then no noise for 1 second then beep three times for shock sensor The last memory heard is the most recent alarm sector triggered Turn the ignition to on to exit this mode When this feature is on the alarm will not trigger when a sudden change in battery current is sensed NOTE This will ONLY beep out the state of this feature e no other active features in the register will be beeped out l e if this feature is NOT on then NO beeps will be heard When this feature is turned on then the Wireless Keypad may be used to disarm the vehicle while still using the standard factory remotes to lock and unlock the vehicle See the Wireless Keypad instructions for further details
6. blinkers will flash once and the siren will beep once For silent arm disarm press both buttons left and bottom If central locking is connected your doors will lock The dash LED light will stay on for 20 seconds then flash THE IMMOBILISER IS NOW_ON LED COMES ON and after 20 seconds starts to flash Press Centre Button Blinkers will flash once TO DISARM YOUR IMMOBILISER amp unlock your vehicle if central locking is connected To deactivate the immobiliser press the Centre Button The blinkers will flash twice and the siren will beep twice The LED will stop flashing If central locking is connected your doors will unlock THE IMMOBILISER IS NOW OFF Note If the alarm has been activated in your absence the siren will beep 4 times on disarm ROSS Press Centre Button Blinkers will flash Twice LED Switches OFF EMERGENCY PANIC CAR FINDER FUNCTION The panic car finder feature is activated by pressing the Right Button on the remote control transmitter This causes the indicators to flash i e same as hazard lights and the siren to sound To cancel panic press the Right Button on the transmitter again NOTE Panic does not work when the ignition is on by requirement of Australian Law EPA Environmental Protection Agency Remote Boot Release BOOT RELEASE Optional connection by installer at extra cost This immobiliser is fitted with remote boot release capability for vehicles with existing electric boot rele
7. o ii a a o N eL 2 RN 3 Standardi System Feature cial cicr 3 Selectable System Features These features can be turned on and Off ooocccooocccccnooccccononnnnconannnnnononnnncononnnnnonnnnncnnn ono 3 Optional ACCES MI ota rio ate candies 3 Detailed Feature Descrip A eee HRN A ee a en ab 4 Auto IMIMODINS 6 e A A n 4 Automatic re arm amp relock Programmable ooooonocccc nocccccononaccnnnonnnonnnnnnncnnnnnn cnn nono n cnn ron ocn n rare Ka aAa NAAA ar EEN Enkara 4 Door Ajar Warning Programmable ici ire 4 Timed Headlight Delay Optional connection by installer at extra COSt ooooncccinnccinnnicinnccnoncnconrcnnnnnnnonncnnnncnnannn naar ca nannnnns 4 Perimeter Night Light Programmable oooooccccnnncccc nncccccnnonccccnonnoncnnonnn cnn nano ncn cnn nn narran arar r ar nn rra r nn nn rar nnn rn rara n cra rnnnnr 4 Dome Light Extension Programmable ooccoconncccc nncccccnnoncccononnnncononnnn canon n cnn ran c nn rana r rra ran r aran rn rn nnnnnnr 4 Glass Break SONS Oi a td Wi ene a ei A Gee ed ie 4 Door Lock On Ignition Programmable cccccccecseceeeeeeeeneeeceeeeeeaeeseeeeeceaeeseeeeeseaeeseaeeesaeeseaeeseeaeescaeesseeesseaeeseieeeseneeeeaes 5 Pre Alert 2 Stage Car Body Impact Warning with ETS o ecccesccceeeeseeeeeeeeeeeeeeeseaeeeseaeeseaeeeseaeesseeeseaeeseaeeeseeeseneeeeaes 5 AUTO Bypass ci a Rd da iaa 5 OPEL id iio 6 Remote Control Funct Oris it ie rias 6 Y NO 6 YouriRemote CONT O tontas tdt rte daly ra
8. FEATURE Remote This Many Times Arming amp Disarming Beeps 1 Door Lock on Ignition 3 Anti Hijack No Door Ajar Warning 4 Perimeter Night Light 5 Instant Boot Release 6 Dome Light Extension 8 Interior lights on when ignition off interior lights on when system disarmed via remote Note This feature cannot be turned on if Auto Rearm amp Relock is activated See register 2 Shock Sensor Adjustment 11 Installer Mode 12 FACTORY SETTING ON oF OFF OFF OFF mor 6 SELECT the level required SELECT The Mode Required DESCRIPTION 1 beep on Arm amp 2 beeps on Disarm When this feature is on the doors will lock when the ignition is turned to on and unlock when the ignition is turned to off When this feature is on the door ajar warning feature is removed the siren amp indicators will not beep amp flash for 3 sec if a door is not closed properly When this feature is on the indicators will stay on constantly for 20 seconds on disarm or until the ignition is turned on This allows for illumination around the vehicle at night When this feature is on the boot release button Left Button will only require be pressing once rather than holding down for 3 seconds to open an electric boot The dome interior light comes on automatically when the system is disarmed via remote enabling the owner to verify the vehicle is safe inside The light stays on for 20 seconds or until the i
9. ase This feature enables the user to unlock the boot by pressing the Left Button for 3 seconds The boot will unlock and the immobiliser will disarm NOTE For safety reasons the remote boot release will not work when the ignition is on Note You can also program the boot to release as soon as you press the Left Programming Additional Remote Controls Erasing Lost Remote Controls Your RES4601a is supplied standard with 2 remote controls You can use up to a maximum of 5 To add a new remote to your alarm simply follow the procedure below Turn the vehicle s ignition to on Immediately press and hold the Centre Button on the original remote control until the indicators start to flash approximately 4 seconds and then release the button Immediately press and hold the Centre Button on the new remote control for at least 4 seconds Turn the vehicle s ignition off The new remote control is now programmed into the immobiliser Erasing Lost Remote Controls If you lose a remote control or perhaps have your car keys stolen you can simply erase the lost stolen remotes by repeating the procedure above 6 times This will fill the system memory with remotes that only you have in your possession Learning In a Remote If all Remotes are Lost You may learn in a remote without having an already learnt in remote Simply perform the Overriding the Immobiliser procedure followed by the remote learning procedure above from step 2 Overrid
10. ave lost their remote controls or they are have stopped working You have the secure choice of over 63 000 possible codes To set a new code 1 After pressing the remote 14 times to enter this mode turn the ignition off The blinkers will flash once to confirm you have entered the override code entry mode Now turn the ignition from on to off anywhere from 3 to 255 times i e 11 times Wait for the blinkers to flash once Now turn the ignition from on to off anywhere from 3 to 255 times i e 36 times Wait for the blinkers to flash once You have changed the override code from the factory setting of 3 4 to 11 36 Make sure you remember the new override number Do not record it anywhere where a would be thief may find it in your car NOTE The driver s door must be left open throughout this procedure 11 WARRANTY TERMS amp CONDITIONS RhinoCo Technology The Company warrants its products to be in conformance with its own plans and specifications and to be free from defects in materials and workmanship under normal use and service for 12 months from the date stamp control on the product or for products not having a date stamp for twelve months from the date of original purchase unless the installation instructions or catalogue sets forth a shorter period in which case the shorter period shall apply The Company s obligation shall be limited to repairing or replacing at its option free of charge for materials or labor any pa
11. bo pida 6 Arming and Disarming Your ImmobiliSer ooonnoconnnncccnnnnncccnnonccnnnnnnnnnnnnnnnnnnnnnnnc nn cnn nn rn enn nn cnn nn nnnn rn E E a cnn 7 Activate Panic or Gar Finder FUuNCUOM iiinn anaa aa aeae tt 7 Remote Boot RAGAS Geroy E A E a E E E 7 Programming Additional Remote Controls Erasing Lost Remote Controls ccccccccccssseceessseeeeeseneeeeessneeeeeseneeeeessaaes 7 Overridine the Inmobiliaria dt tt 8 PHrOSTAMMUNG id AAA AA AA A 8 How to Program the Selectable Features ooomoconnccninnccinnccononccnonnccnnncnnnnnnnnnncnnnn cara n narran n carne 8 Howto Change REGISTER lunas tir da o dada ia 9 How to Change REGISTER Li afraid 11 Installation 2 do e Bee de a ad et ce he ed ds i at T ae eid ds et E ol 12 RES2001 Insurance Requirement cccccccccceseeceeeeececeeeseneeseaeeeeaaeeceaeeeeeeesseaeecganeeseaeeseaeeegeaeeseaeeeseaeeseaeessuaeeseneeeneaees 12 Installing the Main Control Unit ccccecceecseeeeeeeeeeeeeeaeeeeeeeeseaeeeeaeeeseaeeseaeeeseaeeseaeeseaeeeccaeeseaeeesaeescaeeeseaeeseaeesseaeessieeesaes 12 Internal Connector Diagram ccccccececesceeeeneeceneeeeeaeeceneeeeaeeeseaeeeeaneeseaeeseaaeeseaeecaeeseaaeesacesdaaeesaeessaeeseaeeseaeesseaeesseeeesaas 12 Installing the BBSCiSiten cit A agaist abe ld 15 Connecting To An Existing Electric Boot Release Motor cccccccccceceseeeeeeeeeeeeeeeeeeceaeescaeeeseaeeseaeeeseaeeseaeeseaeeseneeesaees 15 Installing Additional Site ns A T 15 I
12. ce amp the LED will start flashing Door Ajar Warning Programmable If the vehicles doors are not properly closed when you try to activate your immobiliser system the indicators will flash and the siren will beep for 3 seconas to alert you that the vehicle is not secure Timed Headlight Delay Optional connection by installer at extra cost You can have your car headlights turn on automatically for 15 seconds when you arm the immobiliser by remote control This may allow you for instance to see your way to your front door or out of a dark car park You can turn the lights off before the 15 second period ends by pressing the left button on your remote Perimeter Night Light Programmable When this feature is on the indicators will stay on constantly for 20 seconds on disarm or until the ignition is turned on This allows for illumination around the vehicle at night Dome Light Extension Programmable The dome interior light comes on automatically when the system is disarmed via remote enabling the owner to verify the vehicle is safe inside The light stays on for 20 seconds or until the ignition is turned on The dome interior light also comes on automatically when the ignition is turned off enabling the owner to quickly gather belongings before exiting the car The light stays on for 20 seconds or until the system is armed via remote or until the ignition is turned on again NOTE If you activate the Automatic Rearm amp Relo
13. ck Feature this feature will be disabled Glass Break Sensor The RES4601A with the addition of a special cabin microphone incorporates intelligent glass break sensing circuitry This inbuilt device will trigger the alarm system provided it registers the correct sound frequency parameters for breaking glass amp that the impact sensor also registers a corresponding vibration to the vehicle This ensures accurate detection of glass breakage Door Lock On Ignition Programmable If you have central locking connected when this feature is on the doors will lock when the ignition is turned to on and unlock when the ignition is turned to off This is to prevent anyone but occupants in the vehicle from being able to open the doors Pre Alert 2 Stage Car Body Impact Warning with ETSTM This special feature provides a two stage impact sensing system It gives the security conscious owner a sensitive car body impact sensor that will give a potential thief prior warning that the vehicle is protected by this most formidable alarm system On detection of a low level impact i e from a tyre kick the siren will simply beep for a few seconds to warn away the would be thief If the vehicle is attacked any further the system will move into full siren mode The unique ETS Environment Tuned Sensor is able to distinguish between environmental shocks caused by aircraft trucks or extreme weather conditions and the impact caused by any thief attempting to break
14. factory the most common configuration chosen and these settings are listed in the REGISTER Settings listed below Once the desired features have been selected the selection is permanently retained in memory even if power is removed To turn on or turn off any feature use the following procedure eg to activate door lock on ignition 1 Find the REGISTER 1or 2 in which the feature is located E g door lock on ignition is located in REGISTER 1 2 Set the vehicle up as described to access REGISTER 1 all doors closed turning ignition on last 3 After turning the ignition to on immediately press the Left Button an equal number of times to the selected feature s code number eg 3 times for door lock on ignition Each press of the remote will be confirmed by a flash of both the blinkers amp the dash LED a confirmation beep will also be produced 4 Turn the ignition to off 5 The system will then confirm which features are activated via visual readout If a feature is enabled the LED 4 indicators will flash out its code corresponding to the number shown in the column Press Remote This Many Times The indicators in this example will flash once for arming beep on then twice for disarm beep on and then three times for door lock on ignition now being on How to Change REGISTER 1 Vehicle Set Up ALL DOORS CLOSED AND THE IGNITION TURNED ON LAST Remote Key action TURN ON OFF FEATURES VIA THE LEFT BUTTON ON THE REMOTE Press
15. gnition is turned on The dome interior light also comes on automatically when the ignition is turned off enabling the owner to quickly gather belongings before exiting the car The light stays on for 20 seconds or until the system is armed via remote or until the ignition is turned on again After pressing the remote 11 times to enter this mode turn the ignition to off There are 8 levels of adjustment The factory default setting is level 6 Pressing the remote once will increase the sensitivity by one level i e to level 7 The LED will then flash seven times to confirm the new level Pressing the remote again will increase the sensitivity to level 8 max Pressing the remote again will return the adjustment to level 1 least sensitive Once you have adjusted the sensitivity level to the desired setting turn the ignition on to exit this mode After pressing the remote 12 times to enter this mode turn the ignition to off This mode allows the installer owner to verify that each trigger of the alarm system is working without having to arm amp disarm the system each time amp set off the siren The siren will beep and the blinkers will flash to indicate a trigger eg push the bonnet switch open a door hit the vehicle The siren will beep four times to indicate a pre warning impact sensor detection or once to indicate full alarm trigger level Turn the ignition to on to exit this mode PAT Past Alarm Trigger Memory Current
16. in or other heavy impacts Furthermore the system features the unique Rhino Auto Adjust process where during the 45 sec arming delay the alarm samples the background noise where the vehicle is parked and will if necessary automatically reduce the sensitivity of the impact sensor to an appropriate level This process allows a trouble free sensitivity that ordinary alarms simply cannot provide The sensitivity level reference point can be adjusted to suit your particular needs Please refer to the programming section contained later in this manual Auto Bypass Auto bypass is designed to reduce false alarms caused by faulty switches or external sensors If the alarm is triggered 3 times by the same sector then the particular sector will be bypassed i e the sector will become inactive The sector will only be bypassed for one arming period The next time the system is armed the sector that was bypassed will become active again Operation Remote Control Functions LEFT BUTTON Press and hold for 3 seconds to activate the boot release feature TOP BUTTON Press for high intensity LED torch Press to Arm and Disarm CENTRE BUTTON RIGHT BUTTON Press to activate panic feature press again to cancel Arming and Disarming Your Immobiliser TO ARM YOUR IMMOBILISER 8 lock your vehicle if central locking is connected The immobiliser is activated by pressing the Centre Button on the remote control transmitter The
17. ing the Immobiliser PROCEDURE This feature enables the owner to override their immobiliser in case they have lost their remote controls or they have damaged them You have the secure choice of over 63 000 possible codes Refer to Register 2 of the Programmable Feature section of this manual page 8 on how to choose your own code This should be done upon installation To enter your override code Open your driver s door and sit in the car The siren will sound this is normal Now turn the ignition from on to off an equal number of times to your first code digit this is a number you have chosen between 3 and 255 Wait for the blinkers to flash once This occurs whether you have entered the correct number or not Now turn the ignition from on to off an equal number of times to your second code digit this is a number you have chosen between 3 and 255 The immobiliser will now disarm You must start your car within 38 seconds otherwise the immobiliser will automatically rearm NOTE Unless a remote control is learnt in if you turn the ignition off you will have to repeat this Programming How to Program the Selectable Features Your Rhino Security system incorporates the latest in high security amp convenience features lt is possible to customise your security system so that it suits your requirements perfectly Detailed below is the full list of programmable features that can either be turned on or turned off We have set at the
18. iren fitted Door ajar warning indicators flash amp siren if fitted beeps for 3 seconds if a door is left ajar i e Vehicle s interior light circuit sees door in open position Electric boot release output via remote control no delay standard feature is to hold button for 3 seconds Timed headlight delay optional feature at additional installation cost Multiple vehicle remote control control 2 cars separately from the 1 remote Central closure allows electric window sunroof closure on arming of some vehicles Door lock on ignition anti hi jack Perimeter night light indicators hold on for 20 seconds on disarm Dome Light Extension interior light turns on for 20 seconds on disarm User programmable override code in case of loss or damage of remotes over 63 000 possible codes Compatible with Transformer interface for vehicles with factory keyless entry systems Allows for factory remote controls to arm disarm the system Compatible with Wireless Keypad to allow arm disarm of the system without remote controls In built 2 stage pre alert car body impact sensor with ETS Audio discriminating glass break sensor Alarm memory allows recall of the10 most recent alarm activations in order Optional Accessories Internal Cabin Siren Ultrasonic Sensors Microwave Sensor Electronic Tilt Sensor Paging System Transformer Interface Wireless Keypad Part No DPS Part No UD6 Part No UD5 Part No TILTSENSE2 Part No
19. nstalling Timed Headlight Delay xc isv acees ieuac ir eair ha Ea INEA ATEREA EEE ARE E 15 Connecting Your System To Central LOCKING ccccccecceeeeneeeeeeeeneeeceneeeceeeesaeeceaaeeceaeeeseaeescaeeesaeeseaeeseeeseeaeeseneesseaees 16 WARRANTY TERMS 8 CONDITIONS coocociccccccccccooncconncncnnncnonncononnn conc nnnn cacon rre n rra rr EEEE eran 19 Features Standard System Features Microprocessor Controlled Three Point Engine Immobilisation Onboard Relays Auto Immobilise Passive Arming Code Hopping Remote Technology Anti Scanning Anti Code Grabbing Two SSR Solid State Remote Controls with 4 Function Operation Arm Disarm Boot Release Panic amp LED Torch Long Life Lithium Cell Remote Control Batteries Each Remote Uses 2 x CR2025 Automatic Re arm in case of Accidental Disarm Ultra Bright Red Flashing LED Light Visual Arming and Disarming via Indicators 1 Flash For On 2 Flashes For Off Safety Circuit Prevents Arming While Ignition On Learning Mode for Adding Additional Remote Controls maximum of 5 Negative On Alarm Output for Optional Internal Cabin Siren Onboard Central Locking Relay Outputs All points of entry alarm protection doors boot bonnet Personal panic button via remote control siren sounds indicators flash Auto Bypass prevents false alarms caused by faulty sensors or switches Selectable System Features These features can be turned on and off Arm disarm beeps if optional s
20. rs if a door is not opened within 60 seconds See page 2 for full function description If you activate this feature dome light extension will be turned off automatically Installers must wire up the door circuit to function When on this feature changes the ARM wire from being a constant negative on arm to a timed 15 second negative on arm wire This will allow you to connect this wire via a relay see diagram on page 15 to your headlight circuit so that when you arm your immobiliser your headlights will turn on for 15 seconds to illuminate your path and then automatically switch off You can press the LEFT button on your remote to turn the lights off before the 15 second period You can still connect window lift modules to this wire as long as it takes no longer than 15 seconds to wind up the windows in the car When off this feature prevents the indicators from flashing when the system is triggered When on the lock output becomes a 15 second negative pulse instead of 0 5 seconds This feature is for certain vehicles with vacuum central locking or those with a central closure wire some BMW Mercedes e doors lock electric windows wind up sunroof closes automatically When on the unlock output becomes a 15 second negative pulse instead of 0 5 seconds This feature is for certain vehicles with vacuum central locking This feature enables the owner to set their own individual code to override their immobiliser in case they h
21. rt which is proved not in compliance with The Company s specifications or proves defective in materials or workmanship under normal use and service The Company shall have no obligation under this Limited Warranty or otherwise if the product is altered or improperly repaired or serviced by anyone other than The Company For warranty service return transportation prepaid to RhinoCo Technology 9 Hannabus Place McGraths Hill NSW 2756 Australia There are no warranties expressed or implied of merchant ability or fitness for a particular purpose or otherwise which extend beyond the description on the face hereof In no case shall The Company be liable to anyone for any consequential or incidental damages for breach of this or any other warranty express or implied or upon any other basis of liability whatsoever even the loss or damage is caused by its own negligence or fault The Company does not represent that the products it sells may not be compromised or circumvented that the products will prevent any personal injury or property loss by burglary robbery fire or otherwise or that the products will in all cases provide adequate warning or protection Customer understands that a properly installed and maintained alarm system may only reduce the risk of a burglary robbery or fire without warning but it is not insurance or a guarantee that such will not occur or that there will be no personal injury or property loss as a result Consequently The
Download Pdf Manuals
Related Search