4400VS-AC-PBIO, 400 Video Segment Instant
Contents
1. Point by pressing NEXT CUE LAST CUE or by manually entering the Cue Point using the numeric keypad eS e The selected Cue Point number is shown on the bottom line of the display 5 Press SHIFT MARK to start the LEARN 6 Select VTR If the VTRs are ganged select one VTR that is part of the Gang The rest of the Gang will be LEARNed automatically 8 4400VS AC Video Segment Accom Attache Protocol PBIO Option 10 Press MARK to complete the LEARN OR Press ESC to exit without LEARNing The ST300 will LEARN save the VTR Number 1 2 3 4 the current gang configuration and the current IN OUT time into the selected Cue Point LEARN ON THE PRODUCTION SWITCHER Select and enable the Peripheral Device Addresses for the ST300 Do a LEARN to the desired REGISTER The ST300 will save the VTR number gang configuration and current IN time into the REGISTER number in the ST300 RECALL ON THE ST300 Select the desired Cue Point by pressing NEXT CUE LAST CUE or by manually entering the Cue Point using the numeric keypad The selected Cue Point number is shown on the bottom line of the display Press GOTO on the ST300 The IN and OUT of the Cue Point becomes the current IN and OUT points The ST300 parks the learned VTR s at the IN point RECALL ON THE PRODUCTION SWITCHER RECALL the desired REGISTER NUMBER The ST300 will automatically load the Learned Segment on the Learned VTR cue the clips to the2. 12843 Foothill Bivd Suite D Sylmar CA 91342 818 898 3380 voice mem 818 898 3360 fax www dnfcontrols com Model 4400VS AC PBIO amp 4400VS AC PBIO T 400 Video Segment Fast Access System Accom Attache and 2Xtreme Protocol Peripheral Bus Interface Option USER MANUAL 4400VS AC Video Segment Accom Attache Protocol PBIO Option 1 SECTION CONTENTS PAGE 1 REVISION HISTORY 3 Zi SYSTEM DESCRIPTION sssssssssecseosecesessssseooeoo 3 Getting Started 3 SYSTEM INSTALLATION ccccsssssssssssssrserccees 4 4 SETUP MENU RE 6 5 LEARN ON THE S7T3000 ccccccssccsccssccsccsscceees 8 6 LEARN ON THE PRODUCTION SWITCHER 9 7 RECALL ON THE ST 3200 seeeeeseeseeeseeSeEEEEEEEEN NN ee 9 8 RECALL ON THE PRODUCTION SWITCHER 9 9 VIEW CONTENTS OF CUE POINTS H 10 PLAY ASEGMEN N KE 9 11 NA Lee TE 10 Advanced Features 12 TRANSFERRING CUELISTS cccssssssrrrec eens 11 Reference 13 FUNCTION TABLE ail 13 14 SPECIEICATIONS ziiuii ian rata 16 15 KEY LAYOUT abi ai 17 16 DNF CONTROLS LIMITED WARRANTY 18 Manual Version a ssssssssssssssnnnunnnnnnnnnnnnnnnnnnnnnnnn 2 4 112503 Document No 4400VS AC PBIO_User_Manual doc 2 4400VS AC Video Segment Accom Attache Protocol PBIO Option Table of Contents 1 REVISION HISTORY 101003 Rev 2 3 Company header information revised 112503 Rev 2 4 Updated Transmit Cue Li
3. 15 LOOP PLAY Press to enter Time Preset Press ENTER to load Time Generator OR press ESC to exit without saving Plays to the end of the segment then plays backward to the first frame of video then plays forward Function is continuous 4400VS AC Video Segment Accom Attache Protocol PBIO Option 14 SPECIFICATIONS Power 90 VAC to 265 VAC adapter supplied with IEC connector Size L x W x H 12 x 6 x 1 5 front 3 0 rear Weight 4 lbs Rear Panel Connectors VTR1 VTR2 VTR3 VTR4 All DB9F GPI DBF15F Power DB9M Aux DB9F Display Easy to read 2 line back lit LCD display User adjustable contrast Jog Shuttle Wheel With mechanical detents Optional T bar Slo mo 0 200 of Play Speed RS422 Serial Connector 9 Pin D Type Female DB9F Pin 1 Frame Ground 6 Receive Common 2 Receive A 7 Receive B 3 Transmit B gt 8 Transmit A gt 4 Transmit Common 9 Frame Ground 5 Spare Power Connector 9 Pin D Type Male DB9M Pin 1 5v DC 6 5 VDC 2 5v DC 7 Ground 3 Ground 8 Ground 4 12 VDC 9 Ground 5 12 VDC GPI IN OUT Connector 15 Pin D type Female DB15F Pin 1 GPI 1 Out 6 GPI 6 Out 11 GPI 3 In 2 GPI 2 Out 7 GPI 7 Out 12 GPI 4 In 3 GPI 3 Out 8 Ground 13 GPI 5 In 4 GPI 4 Out 9 GPI 1 In 14 GPI 6 In 5 GPI 5 Out 10 GPI 2 In 15 GPI 7 In 16 4400VS AC Video Segment Accom Attache Protocol PBIO Option 15 KEE i Le 17 FE VA KEY LAYOUT STI00 KEY C
4. Learned time and set the Learned GANG mode VIEW CONTENTS OF CUE POINTS Press and hold SHIFT NEXT CUE OR LAST CUE The display shows the current cue number and its contents for the current VTR Release the keys to exit the view mode PLAY A SEGMENT Select a video segment by pressing LAST CUE or NEXT CUE OR Enter the desired cue number on the numeric keypad Press GOTO Press and hold SHIFT then press and release PLAY 4400VS AC Video Segment Accom Attache Protocol PBIO Option 11 TRIGGER FROM THE PRODUCTION SWITCHER The operator fires a trigger using either the TIMELINE or RUN function on the production switcher The ST300 puts the VTR into the following modes based upon the trigger value GRASS VALLEY VALUES Trigger Value 0 1 2 3 4 5 6 7 8 9 or greater SONY VALUES Trigger Value 0 1 2 3 4 5 6 7 8 9 or greater Mode Play Segment Recue to beginning of clip Slo mo using ST300 Wheel Preset or T Bar Speed Reverse Play Still Frame Loop Record Play Play Ping Pong Play Mode Recue Play Segment Slo mo using ST300 Wheel Preset or T Bar Speed Reverse Play Still Frame Loop Record Play Play Ping Pong Play 10 4400VS AC Video Segment Accom Attache Protocol PBIO Option ADVANCED FEATURES 12 TRANSFERRING CUELISTS The TRANSMIT CUELIST function allows you to transmit your list of Cue Points to a PC using the provided utility software on the PC or to an
5. NSMIT Transmits Cuelist to another ST300 or to a PC CUELIST RECEIVE Receives Cuelist from another ST300 or a PC CUELIST 7 4400VS AC Video Segment Accom Attache Protocol PBIO Option 5 LEARN ON THE ST300 MARK AN IN OUT POINT Press IN OUT The IN OUT indicator turns ON The second row of the display shows the currently marked IN OUT time for Y2 second The current time is marked into the IN OUT point VIEW THE IN OUT POINT When the IN OUT indicator is ON the content of an IN OUT point can be viewed by pressing and holding IN OUT ENTERANIN OUT POINT 1 Press SHIFT IN OUT The first row of the display shows the current IN OUT time The second row of the display shows ENTER IN OUT If there is no IN OUT point currently selected on that VTR the first row of the display shows 22 22 22 2 Enter the desired IN OUT time using the numeric keypad 3 Press ENTER to save entered time as an IN OUT time OR Press ESC to exit without saving GOTO IN POINT When the IN OUT indicator is ON press GOTO or RECUE to search to the current IN OUT point DELETE IN OUT POINT Press DEL IN OUT LEARN A SEGMENT INTO A CUE POINT Select VTR 1 2 3 or 4 to establish a Cue Point MARK or ENTER an IN and OUT point on currently selected VTR If Gang mode is desired repeat steps 1 amp 2 until all the VTRs have IN amp OUT points Select the desired Cue
6. ONFIGURATION nn Kl Kl Kal Ka O O Le on meae ES OUT LOOP VE E E DNF S7300 VTR 7 DDA Controlfer GFELEGPI L4OWS AC amp 4400V8 AC E PRE ROLL O O N__ rai ES CH CO nn Ni 4400VS AC Video Segment Accom Attache Protocol PBIO Option 16 DNF CONTROLS LIMITED WARRANTY DNF Controls warrants its product to be free from defects in material and workmanship for a period of one 1 year from the date of sale to the original purchaser from DNF Controls In order to enforce the rights under this warranty the customer must first contact DNF s Customer Support Department to afford the opportunity of identifying and fixing the problem without sending the unit in for repair If DNF s Customer Support Department cannot fix the problem the customer will be issued a Returned Merchandise Authorization number RMA The customer will then ship the defective product prepaid to DNF Controls with the RMA number clearly indicated on the customer s shipping document The merchandise is to be shipped to DNF Controls 12843 Foothill Blvd Suite D Sylmar CA 91342 USA Failure to obtain a proper RMA number prior to returning the product may result in the return not being accepted or in a charge for the required repair DNF Controls at its option will repair or replace the defective unit DNF Controls will return the unit prepaid to the customer The method of shipment is at the discretion of DNF Controls princ
7. at 100 play speed For Wheel only Press Softkey SPEED to select SLOMO speed ranges Press Softkey to select 0 gt 200 OR 100 gt 200 Press Softkey BACK to return to SLOMO MENU Press ESC to exit OR turn the Wheel to select another item 6 4400VS AC Video Segment Accom Attache Protocol PBIO Option For Wheel only Press Softkey PRSET to select the SLOMO Preset Speed Mode Press Softkey UPDATE When exiting SLOMO mode the last used speed is saved in the Preset Speed register Press Softkey STATIC The Preset Speed register is NOT updated when exiting SLOMO mode It is only changed by SHIFT SLOMO PRESET SLOMO ST300 ST300 SETUP SETUP Clear Cues SetDefault Press Softkey beneath ClearCues to clear all Cue Points to 00 00 00 00 Press Softkey YES when asked Are You Sure Press Softkey beneath SetDefault to set ST300 to default settings Press Softkey YES when asked Are You Sure DISPLAY The version number for the currently installed software is SOFTWARE displayed VERSION DROP Press Softkey to select DROP FRAME ON or OFF FRAME Used in conjunction with Timecode Generator preset RECORD Press Softkey to select single button or 2 button record RECORD REC Only OR REC PLAY FREEZE Press Softkey to enable or disable FREEZE at Record Outpoint Changing mode automatically clears FREEZE point PBIO 1 through 23 ADDRESS SWITCHER Grass Valley Group or Sony TYPE TRA
8. ck and Easy way to access and play up to 400 video segments Each ST300 Cue Point consists of an IN point and an OUT point IN OUT points can be manually entered or marked with the current tape time from the Video Server All Cue Points are retained when power is off DEFINITIONS a Throughout this document VTR DDR VDR amp Video Server will be referred to collectively as Video Server Q The ST300 S SM as the ST300 a Words surrounded by brackets for example ENTER are keys on the ST300 XXX XXX means hold the two keys down simultaneously 3 4400VS AC Video Segment Accom Attache Protocol PBIO Option Getting Started di SYSTEM INSTALLATION ST300 S SM VTR DDR CONTROLLER 1 4 Plug one end of a 9 conductor RS422 serial cable into the VTR 1 2 3 or 4 connector on the rear of the ST300 Plug the other end of the cable into the REMOTE connector on the Video Server Connect the 5 12 12 VDC POWER SUPPLY into the POWER connector on the rear of the ST300 Plug the Power Supply into an outlet 90 VAC to 240 VAC Check SETUP MENU prior to using the ST300 to confirm proper Record mode and other User settable modes Select REMOTE mode on the Video Server s front panel PRODUCTION SWITCHER l Plug one end of a 9 conductor RS422 serial cable into the AUX connector on the rear of the ST300 Connect the other end of the cable to the Peripheral Bus Connector on the production switc
9. ent Accom Attache Protocol PBIO Option LCD DISPLAY During normal operation the top row of the display shows the selected time mode and current time location of the VTR For example TM 01 12 09 23 Time Modes TM Tape Timer TC LTC VT VITC The currently selected SLO MO speed is displayed on the far right side of the top row The bottom row of the display shows the current Cue Point number and its contents 4 SETUP MENU Press MENU The MENU indicator will turn on Turn the Wheel to select item to change Press MENU OR use the Softkeys to change the desired mode for that option Turn the Wheel at anytime to select another item Press ESC at anytime to exit SETUP MENU The MENU indicator will turn off MENU MODES Turning Wheel clockwise RECORD Press MENU to select the desired record mode Lockout Assemble Crash Full or Insert Only in INSERT mode Press the associated Softkey located below the display to toggle Video V Audiol A1 Audio2 A2 Audio3 A3 Audio4 A4 on off WIND Press Softkey to select MODE HOLD fast wind is maintained only while key is depressed OR LATCH fast wind is initiated and maintained with momentary key press Select fast wind speed 3 9 to 23 7 by pressing Softkey below SPD SLOMO ST300 display shows SLOMO with WHEEL TBAR Speed Prset Press Softkey TBAR or WHEEL to toggle between them NOTE The T BAR has a fixed speed range of 0 gt 200 with a detent
10. her Communication Format 38 4K N 8 1 To select a Production Switcher type default Grass Valley Group a Press MENU and turn the wheel until SWITCHER is displayed b Press Softkey to toggle between Sony and Grass Valley Group types Press ESC at anytime to exit MENU mode The ST300 has 4 Peripheral Device Addresses one for each VTR that it controls To set the Device Address for each VTR Press MENU and turn the wheel until Peripheral Address is displayed Press VTR 1 VTR 2 VTR 3 or VTR 4 to select a VTR Assign a Peripheral Device Address for that VTR from 0 to 23 by entering the desired address using the numeric keypad To turn off the address press DEL Any address gt 23 turns off the address Select the next VTR and assign a Peripheral Device Address for it Each VTR should have its own unique address When done press ESC to exit the MENU Configure the production switcher Enable the Peripheral Bus Enable the Peripheral Device Addresses assigned to the ST300 Enable the appropriate Learn Recall levels Enable the Timeline or Recall Trigger function Installation is complete 4 4400VS AC Video Segment Accom Attache Protocol PBIO Option CONNECTION DIAGRAM ST300 SSM REF VIDEO ds SS Server LCD contrast POWER GPI IN OUT RESE PIN1 5v PIN3 GND POWER SUPPLY 5 4400VS AC Video Segm
11. ipally UPS Ground for shipments within the United States of America Shipments to international customers will be sent via air Should a customer require the product to be returned in a more expeditious manner the return shipment will be billed to their freight account This warranty will be considered null and void if accident misuse abuse improper line voltage fire water lightning or other acts of God damaged the product All repair parts are to be supplied by DNF Controls either directly or through its authorized dealer network Similarly any repair work not performed by either DNF Controls or its authorized dealer may void the warranty After the warranty period has expired DNF Controls offers repair services at prices listed in the DNF Controls Price List DNF Controls reserves the right to refuse repair of any unit outside the warranty period that is deemed non repairable DNF Controls shall not be liable for direct indirect incidental consequential or other types of damage resulting from the use of the product HH 18 4400VS AC Video Segment Accom Attache Protocol PBIO Option
12. oint enter the desired timecode number using the numeric keypad Press GOTO to search to the entered time Press ESC to exit without searching FREEZE ON Active in SLO MO In SLO MO mode STILL frame the VTR when the LAST GOOD only current time code is within 6 frames of the last VIDEO Record Out point memorized automatically upon exiting Record mode Enable disable or clear FREEZE point from SETUP MENU GOTO CUE or GOTO Search the VTR to the contents of the currently ENTERED displayed Cue Point If ENTER TIME is active TIME LED is on search the VTR to the entered time To enter a GOTO location without altering the contents of the Cue Point Press ENTER TIME Enter the desired timecode number using the numeric keypad Press GOTO to search to the entered time Press ESC to exit without searching SHIFT VTR 1 Select VTRs to gang together The ganged VTRs SHIFT VTR 2 LEDs will turn on Press ESC to exit SHIFT VTR 3 SHIFT VTR 4 GOTO SHIFT GOTO Search VTR to FREEZE point last Record Out FREEZE point POINT 13 4400VS AC Video Segment Accom Attache Protocol PBIO Option FFWD FFWD Press and HOLD to shuttle Release key to stop Set WIND Speed in MENU JOG Select JOG mode and enable the Wheel LAST CUE LAST CUE Step to the previous Cue Point Location MARK CUE MARK Save the current time in the currently displayed Cue POINT Point Per SETUP MENU the Cue Poin
13. other ST300 Transfer to a PC requires OpSuite 3 0 software which runs on a Windows based computer Contact DNF Controls for more information TRANSMIT CUELIST FUNCTIONS To Transmit a Cuelist to an ST300 1 7 8 Connect the VTR 4 connector on the rear of the ST300 to the VTR4 connector of the receiving St300 using an RS422 9 pin cable with TX and RX lines crossed A turnaround cable Press MENU Scroll the wheel until Transmit CUE List YES Enter Exit ESC is displayed Press ENTER to start transmitting The Display shows Waiting to transmit on the first line When the Receiver is ready transfer starts automatically The Display now shows Transmitting cuelist After the transfer is over the display shows Transfer is over for one second and then shows Waiting to transmit again Connect another ST300 to transmit the list again OR Press ESC twice to exit the MENU mode To Transmit a Cuelist to a PC l 2 11 Connect the VTR4 connector on the back of the ST300 to one of the COM ports on the PC using a RS422 to RS232 adapter Repeat steps 2 8 of the TRANSMIT CUE POINTS to the ST300 section 4400VS AC Video Segment Accom Attache Protocol PBIO Option RECEIVE CUELIST FUNCTION The RECEIVE CUELIST function allows you to receive your list of Cue Points from a PC or from another ST300 Transfer to a PC requires OpSuite 3 0 software which runs on a Windows based com
14. puter Contact DNF Controls for more information To Receive a Cuelist from an ST300 Connect the VTR4 connector on the back of the ST300 from the VTR4 connector of the transmitting ST300 using RS422 9 pin cable with TX and RX lines crossed A Turnaround Cable Press MENU Scroll the wheel until Receive CUE List YES Enter Exit ESC is displayed Press ENTER to start receiving The Display shows Waiting to receive on the first line When the Transmitter is ready transfer starts automatically The Display now shows Receiving cuelist After the transfer is over the display shows Done Success Press any key Press any key The display shows Receive cuelist message Press ESC to exit the MENU mode To Receive a Cuelist from a PC l 2 12 Connect the VTR4 connector on the back of the ST300 to one of the COM ports on the PC using RS422 to RS232 adapter Repeat steps 2 8 of the RECEIVE CUE POINTS from the ST300 section 4400 VS AC Video Segment Accom Attache Protocol PBIO Option GE sua FUNCTION TABLE EE On Off EE Toggle EE mode on off Status indicator is on when EE is on ENTER TIME ENTER TIME To manually entered timecode numbers into the currently displayed Cue Point Enter the desired timecode number using the numeric keypad Press ENTER to save your entry OR ESC to exit without saving To enter a GOTO location without altering the contents of the Cue P
15. st Function and Receive Cue List Function description Added DNF Controls Limited Warranty 2 DESCRIPTION NOW production switchers can load amp play video segments on Accom Attache and 2Xtreme a Use the EMEM or SNAPSHOT Learn amp Recall functions of the production switcher to load and play a video segment from a Recall or timeline a Use the Run and Trigger functions of the production switcher to Play Stop or Recue the video segment The PERIPHERAL BUS INTERFACE Option for the ST300 VTR Controller is special software in the ST300 With this Option the ST300 has 4 Peripheral Device Addresses one for each VTR that it controls This allows the production switcher to control any and all VTRs connected to the ST300 Upon receipt of the Learn command from the production switcher the ST300 saves the IN and OUT points for the currently defined video segments the VTRs they are loaded on and the current GANG mode into the appropriate Cue Point When the Recall command is received the ST300 loads the learned IN amp OUT onto the learned VTRs cues the VTR to the learned IN time then restores the learned GANG mode Learn amp Recall may also be done directly from the ST300 without the production switcher The Trigger function on the production switcher puts the selected VTRs in to Play Stop Recue or other available modes The SEGMENT PLAYBACK option for the ST300 VTR Controller in combination with a DDR or VTR provides a Qui
16. t Location will advance to the next Cue Point location or remain the same NEXT CUE NEXT CUE Step to the next Cue Point Location PREROLL PREROLL Preroll the VTR to the contents of the currently displayed Cue Point PREROLL Enter desired Preroll Value Press ENTER to VALUE save entry OR press ESC to exit without saving entry RECORD REC Places VTR in the Record mode selected by RECORD MODE in the SETUP MENU One button record REWIND Press and HOLD to shuttle Release key to stop Set WIND Speed in MENU SHUTTLE SHUTTLE Select SHUTTLE mode and enable the Wheel SLOMO SLOMO Press SLOMO to slo mo the VTR Turn the Wheel or move the T Bar to change the play speed Press SLOMO to STILL frame OR press any transport key to exit SLO MO SHIFT SLOMO For WHEEL ONLY Press SHIFT SLOMO SPEED to preset the slo mo speed Turn the Wheel to PRESET select desired speed Press ESC or any transport key to exit STOP STOP Press once to STILL frame VTR Press again to put VTR into STOP mode TIME MODE TIME MODE Press to toggle between Timecode TC VITC SELECT VT or Tape Timer TM display modes LOOP PLAY LOOP PLAY Video segment plays from first frame of video to last frame then plays again from first frame Function is continuous 14 4400VS AC Video Segment Accom Attache Protocol PBIO Option TIME SHIFT PRESET TIME MODE Generator Preset PING PONG SHIFT PLAY
Download Pdf Manuals
Related Search