Elite Screens Evanesce Plus 180"
Contents
1. Large In Ceiling Electric Motorized Front Projection Screen Evanesce Plus Series User s Guide Important Safety amp Warning Precautions Make sure to read this user s guide and follow the procedures below Caution The screen s Black Top Drop is already set to its maximum drop distance There is NO extra Black Top Drop in the roller Please be aware of this as it will void your warranty with Elite Screens Unapproved changes or modifications except for cutting the power cord for hardwire installations to this unit are prohibited and will void your warranty For more information please contact our Technical Support Department at 877 511 1211 Ext 604 e Please retain this user s guide for future reference e To avoid damaging the unit do not use with any unauthorized accessories not recommended by the manufacturer e Handle the unit carefully during transportation to avoid any damages e To ensure safe and reliable operation direct connection to a properly grounded power source is advised e The power outlet supplying power to the unit should be close to the unit and easily accessible e Donot install the unit on uneven inclined surfaces e Do not install in damp places to avoid an electric shock or short circuit e Do not place any heavy objects over the power cord e Position the power cord properly to avoid creating a trip obstacle e To avoid an electrical shock or fire due to a loose contact or short circui2. into the housing groove top part and housing to come together Attention 1 The end flange panels can easily warp Please be careful when handling them and during installation 2 Make sure the end flanges are properly installed and leveled with the housing Ji 3 As a safety precaution four people are required Cei Ing for this installation SY FLA OE a a a EF aE LP AT a a A 1 End flange piece location For local Elite Screens contact or Technical Support please visit www elitescreens com Rev 040313 JA www elitescreens com
3. ill retract when the projector powers down The 5 12 volt adaptor connects to your projector s trigger output via a separate cable that may or may not be provided by the manufacturer of the projector The trigger feature will not work without an output cable from the projector but it can be tested by connecting the Red and Green cable to a 9 volt battery 2 3 Way Wall Switch The 3 way wall switch is a wall mount control box with an up stop down button and plugs directly into the screen s RJ 45 input 4 IR Remote Control The Infrared functions by direct line of sight contact with a beam range of 30 feet Rev 040313 JA RJ45 input To Projector Red DC12V Green OV 5 12 VOLT TRIGGER CABLE 3 IR Eye Receiver plugs directly into the screen s RJ 45 input to present a low profile line of sight control option for your IR remote control even in a recessed ceiling installation 5 RF Remote Control The radio waves eliminate the need for a direct line of sight with a range of 100 feet www elitescreens com Hardware Parts List for Evanesce Plus Series Please make sure all parts listed below are included before proceeding with the installation A Hexagonal nut x 4 B M6x13 hex screw x 8 C Hanging bracket x 2 D Washer x 12 E Turnbuckle x 4 F Suspension Bar x 4 G M6 nut x 4 H End cover flange panel 9 Power The Evane
4. nting hardware is used to provide adequate strength suitable for the installation Elite Screens is not liable for any faulty installations For limit adjustment instructions please contact our Technical Support Department at 877 511 1211 Ext 604 The Screen s Top Black Drop is already set to its maximum drop distance There is NO extra top black drop in the roller Please be aware of this as it will void the limitation of your warranty Individual modifications to this product are prohibited and will void the warranty with the manufacturer Please contact Elite Screens Customer Service for any questions NOTE This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that the interference will not occur on a particular installation If this equipment causes harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures v Reorient or relocate the receiving antenna of the device which ma
5. sce Plus Series includes a 3 Prong Power Cord for use in a non concealed power outlet If your installation will be entirely concealed including the power outlet Elite Screens strongly recommends a hardwire connection Please refer to the image below for both 110v amp 220v wiring information 110V i A Hise Is y an _ b Pig 220V La Assembly 1 Insert the M6x13 hex screw B through the Hanging Bracket s C screw hole and secure with the Hexagonal nut A Slide the Hanging Bracket C through the railing on top of the case Repeat the same for the other side Rev 040313 JA www elitescreens com 4 2 Attach the Turnbuckle E to the bottom of the Suspension Bar F and secure with the Hex Screw B Washer D and Hex Nut H E E i li Iu E IS l Sa i e U fas ri ED yoy 3 Attach the Turnbuckle G to the Hanging Bracket C as shown in figure below Install the Suspension Bars D to your ceiling according to their distance pw i 4 a a Rotate the turnbuckle s as needed to adjust the height level a 4 Attach the end flange piece C on the long edge of the housing as shown below to complete the assembly The screen is now ready for installation Rev 040313 JA www elitescreens com if Leaning the end flange piece and put the bottom part so it may Push the end flange upwards to allow the j j i nd housin m her insert
6. t do not overload the power cord e The internal amp external parts of this unit are not end user serviceable Do not attempt to disassemble this unit by yourself No one except authorized technicians can open and make repairs to this unit e Make sure the power source that this unit is connected to has a continuous power flow e f there is need to use an extension cord make sure the cord has an equal rating as the appliance to avoid over heat e Do not handle the power plug when your hands are wet or your feet are in contact with water e Properly dispose of this equipment according to the environmental regulations in your area when product is no longer of service Rev 040313 JA www elitescreens com 1 Do not use this unit under the following circumstances e Disconnect the power cord under the conditions of heavy rain wind thunder or lightning e Avoid direct sun light rain shower and moisture e Keep away from fire sources and high temperature to prevent this device from overheating e Cut off the power supply first before transportation or maintenance e To avoid possible injury and or an electric shock do not attempt to use this screen if there is obvious damage or if there are any evident broken parts Installation Warning The instructions provided in this user s guide are for reference only Please consult a professional installation company for further installation and safety advice The installer must insure that proper mou
7. y be casing the interference v Increase the separation between the screen and the device s receiver Y Connect the equipment into a different power outlet other than the device Pre Installation 1 Carefully unpack the screen 2 Always handle the screen in a leveled position on a clean surface 3 In order to protect the screen from exposure to stains keep the screen out of contact with foreign particles such as dust sawdust and or liquids Regardless of the mounting method the screen should be securely supported so that the vibration or pulling on the viewing surface will not cause the casing to become loose or fall The installer must insure the fasteners that are used are of adequate strength and suitable for the installation location Rev 040313 JA www elitescreens com 2 Accessories for Evanesce Plus Series Please make sure all accessories listed below are included before proceeding hen A A 0 E YJ 4 7 G Bubble leveler E TPR DEN AT s w i J C Remote igi wip j control base D S IE A IR Remote B RF Remote x2 a f isi fg i f EN H Q x z t we fer ww _ Red Green tite Sa E IR eye F 5 12v trigger cable G AAA D 3 way receiver Batteries x 2 wall switch 1 5 12V Trigger The built in 5 12V trigger input allows your screen to synchronize its drop amp rise with the projector s power cycle The screen deploys when the projector powers up and w
Download Pdf Manuals
Related Search