Zipato VS-ZP3102.US Multi Sensor Dual
Contents
1. everything under control MULTI SENSOR DUAL QUICK INSTALLATION GUIDE v1 TRADEMARKS Zipato and the Zipato logo are registered Trademarks All other product names mentioned herein may be trademarks or registered trademarks of their respective companies NOTICE Although Zipato has attempted to ensure the accuracy of the content of this manual it is possible that this document may contain technical inaccuracies typographical or other errors Zipato assumes no liability for any error in this publication and for damages whether direct indirect incidental and consequential or otherwise that may result from such error including but not limited to loss of data or profits Zipato provides this publication as is without warranty of any kind either express or implied including but not limited to implied warranties of merchantability or fitness for a particular purpose The published information in the manual is subject to change without notice Zipato reserves the right to make changes in the product design layout and driver revisions without notification to its users This version of the Installation guide supersedes all previous versions ELECTROMAGNETIC COMPATIBILITY In proper state and when operated properly the product complies with all the requirements in respect of interference radiation according to EN 301 489 17 EN 301 489 1 and EN 300 328 The connections conducting HF signals must neither be ma2. 908 42MHz vs zp3102 us 921 42MHz vs zp3102 au OPERATING RANGE Up to 100 feet line of sight OPERATING TEMPERATURE 15 C 40 C 5 F 104 F BATTERY Panasonic CR123A 1PC PACKAGE CONTENT FREQUENCY RANGE ZP 3012 sensor 1R Adhesive tape for sensor 1 CR123A Lithium Battery 1P Installation amp Operation Manual s INSTALLATION Notice If you are installing the entire Z Wave TM system for the first time please refer to the installation guide of Z Wave TM Interface Controller before installing Vs zp3102 1 Release cover tab to open the cover 2 Insert a CR123A battery into the battery compartment and LED will start to flash slowly which means the sensor has not yet been inclusion www zipato com 3 Close the cover back to sensor 4 FOR INCLUSION IN ADDING TO Put the Z Wave TM Interface Controller into inclusion mode and following its instruction to add the Vs zp3102 to your controller To get in the inclusion mode the distance between sensor and controller is suggested to be in one meter Press the program switch of Vs zp3102 once The LED on the Vs zp3102 should stop flashing if not please try again FOR EXCLUSION FROM REMOVING FROM A NETWORK Put the Z Wave TM Interface Controller into exclusion mode and following its instruction to delete the Vs zp3102 to your controller Press the program switch of Vs zp3102 once to be excluded The LED on th
3. domestic use in particular those listed in the first and last boxes in the table below this Limited Product Warranty extends only to the original end user purchaser of this ZIPATO Hardware Product and is not transferable to anyone who obtains ownership of the ZIPATO Hardware Product from the original end user purchaser PRODUCT WARRANTY PERIOD TABLE PRODUCT TYPE Product Warranty Period MULTI SENSOR DUAL One 1 year IMPORTANT The content of Product Type listed above is subject to change please refer to the www zipato com for latest update PERFORMANCE OF THE LIMITED PRODUCT WARRANTY If a product defect occurs ZIPATO s sole obligation shall be to repair or replace any defective Zipato Hardware Product free of charge provided it is returned to an Authorized ZIPATO Service Centre during the Limited Warranty Period Such repair or replacement will be rendered by ZIPATO at an Authorized ZIPATO Service Centre All component parts or hardware products that www zipato com are replaced under this Limited Product Warranty become the property of ZIPATO The replacement part or product takes on the remaining Limited Warranty Period of the replaced part or product The replacement product need not be new or of an identical make model or part ZIPATO may in its discretion replace the defective product or any part thereof with any reconditioned equivalent or superior product in all material respects to the defective produ
4. TATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR CONSUMER PRODUCTS IN SUCH STATES OR COUNTRIES SOME EXCLUSIONS OR LIMITATIONS OF THIS LIMITED WARRANTY MAY NOT APPLY TO YOU THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS YOU MAY ALSO HAVE OTHER RIGHTS THAT MAY VARY FROM STATE TO STATE OR FROM COUNTRY TO COUNTRY YOU ARE ADVISED TO CONSULT APPLICABLE STATE OR COUNTRY LAWS FOR A FULL DETERMINATION OF YOUR RIGHTS This Limited Product Warranty applies to ZIPATO branded hardware products collectively referred to as ZIPATO Hardware Products sold by ZIPATO Europe its European subsidiaries affiliates authorized resellers or country distributors collectively referred to as ZIPATO Resellers with this Limited Product Warranty The term ZIPATO Hardware Product is limited to the hardware components and all its internal components including firmware The term ZIPATO Hardware Product DOES NOT include any software applications or programs we make every home smart LIMITATION OF PRODUCT WARRANTY ZIPATO warrants that the products described below under normal use are free from material defects in materials and workmanship during the Limited Product Warranty Period set forth below Limited Product Warranty Period if the product is used and serviced in accordance with the user manual and other documentation provided to the purchaser at the time of purchase or as amended from time to time ZIPATO doe
5. ct WARRANTOR Tri plus grupa d o o Banjavciceva 11 10 000 Zagreb CROATIA TELEPHONE 385 1 444 444 00 FACSIMILIE 44 0 208 955 9001 DECLARATION OF CONFORMITY The Manufacturer Tri plus grupa d o o hereby declares that the product Zipabox Smart home controller 1 CE In accordance with the following Directivels 2006 95 EC The Low Voltage Directive 89 336 EEC The Electromagnetic Compatibility Directive and 1999 5 EC R amp TT EC Directive is in conformity with the e applicable requirements of the following documents EN 61326 EN 61000 3 3 EN 61000 4 4 EN 61000 4 11 IEC EN 55011 EN 61000 6 2 EN 61000 4 5 EN 301 489 1 3 EN 300 220 2 EN 61000 4 2 EN 61000 4 6 AS NZS IEC 60335 2 97 EN 61000 3 2 EN 61000 4 3 EN 61000 4 8 EN 60335 1 hereby declare that the equipment named above has been designed to comply with the relevant sections of the above referenced specifications The unit complies with all applicable Essential Requirements of the Directives Person responsible for this declaration Dean Janacek Certification Manager 01 09 2012 Changes or modifications not expressly approved Tri plus grupa d o o for compliance could void the user s authority to operate the equipment Fe THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interfere
6. e Vs zp3102 should start to flash FOR ASSOCIATION removing the cover of the Vs zp3102 to get into Awake mode then put the Z Wave TM Interface Controller into association and following its instruction to associate the Vs zp3102 with other device Close the cover back after association done afterward the Vs zp3102 will get into Sleep mode for power saving Support one association group 5 nodes NOTE AWAKE MODE it is to leave the Sleep mode by removing the cover of Vs zp3102 to allow the Z Wave TM Interface Controller to do Association 5 Using adhesive tape to mount Vs zp3102 at 2 meters above surface To enhance proper operation place Vs zp3102 on the angle which can detect the room widely The solid area means the detector s coverage range SENSOR tenctH 10M SENSOR 60 012345678 9 10 we make every home smart OPERATION 1 Walk in front of Vs zp3102 sensor will send the status of ON Basic Set Value 0xFF to any associated nodes and the LED will flash once 2 If no movement detected in three minutes after sent status of ON the sensor will send the status of OFF Basic Set Value 0x00 to any associated nodes 3 Normal operation the LED will not light 4 The Vs zp3102 sensor equipped with tamper switch If the cover of sensor is removed the PIR sensor will send an alarm report type 01 level 11 t
7. ed Consult the dealer or an experienced radio TV technician for help COPYRIGHT 2012 Tri plus grupa d o o All Rights Reserved No part of this manual may be reproduced or transmitted in any form without the expressed written permission of Tri plus grupa d o 0 www zipato com
8. nce that may cause undesired operation Le pr sent appareil est conforme aux CNR d Industrie Canada applicables aux appareils radio exempts de licence L exploitation est autoris e aux deux conditions suivantes 1 Uappareil ne doit pas produire de brouillage et 2 l utilisateur de l appareil doit accepter tout brouillage radio lec trique subi m me si le brouillage est susceptible d en comprom ettre le fonctionnement NOTE This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications we make every home smart However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connect
9. nipulated nor damaged TAKE CARE OF YOUR SAFETY Display extreme caution when using ladders or steps please follow manufacturer s instructions Be careful when using hand and power tools and follow the manufacturer s guidelines when using them Take care that the correct tools are used Wear goggles or protective clothing where required INTRODUCTION Thanks for choosing the Vision s wireless PIR motion sensor of the home security device This sensor is a Z Wave TM enabled device interoperable two way RF mesh networking technology and is fully compatible with any Z Wave TM enabled network Every mains powered Z Wave TM enabled device acts as a signal repeater and multiple devices result in more possible transmission routes which helps eliminate RF dead spots Z Wave TM enabled device displaying the Z Wave TM logo can also be used with it regardless of the manufacturer and ours can also be used in other manufacturer s Z Wave TM enabled networks This sensor monitors movement and send Z Wave TM signal when movement is detected inside the building we make every home smart PRODUCT DESCRIPTION AND SPECIFICATION Cc Tamper switch Program Adhesive Battery Switch Tape Sensor KEEP THE SURFACE OF SENSOR AND LENS CLEAN WIPE WITH CLEAN AND SOFT CLOTH Tab to release cover LED status indicator SPECIFICATION TECHNICAL SPECS PROTOCOL Z Wave ZM3102N 868 42MHz vs zp3102 eu
10. o the Z Wave Interface Controller and the LED will go solid Before replacing the cover the sensor is uder Awake mode TECHNICAL SUPPORT Having trouble installing your new product Zipato s website contains the latest user documentation and software updates for Zipato products and services www zipato com CALL SUPPORT 385 1 4004 404 Mon Fri 9 00am 06 00 www zipato com everything under control MULTI SENSOR DUAL GEOGRAPHICAL SCOPE OF THE LIMITED PRODUCT WARRANTY This Limited Product Warranty is applicable to Hardware Products sold by Zipato Resellers in all countries listed at the beginning of this document under the heading Countries in which this ZIPATO Limited Product Warranty applies The Limited Product Warranty will be honored in any country where ZIPATO or its authorized service providers offer warranty service subject to the terms and conditions set forth in this Limited Product Warranty However warranty service availability and response times may vary from country to country and may also be subject to registration requirements QUICK INSTALLATION GUIDE v1 LIMITED PRODUCT WARRANTY GENERAL TERMS Nothing in this Limited Product Warranty affects your statutory rights as a consumer The Limited Product Warranty set forth below is given by Tri plus grupa d o o Europe herein referred to as ZIPATO This Limited Product Warranty is only effective upon presen
11. s not warrant that the products will operate uninterrupted or error free or that all deficiencies errors defects or non conformities will be corrected This warranty shall not apply to problems resulting from a unauthorized alterations or attachments b negligence abuse or misuse including failure to operate the product in accordance with specifications or interface requirements c improper handling d failure of goods or services not obtained from ZIPATO or not subject to a then effective ZIPATO warranty or maintenance agreement e improper use or storage or f fire water acts of God or other catastrophic events This warranty shall also not apply to any particular product if any ZIPATO serial number has been removed or defaced in any way ZIPATO IS NOT RESPONSIBLE FOR DAMAGE THAT OCCURS AS A RESULT OF YOUR FAILURE TO FOLLOW THE INSTRUCTIONS FOR THE ZIPATO HARDWARE PRODUCT LIMITED PRODUCT WARRANTY PERIOD The Limited Product Warranty Period starts on the date of purchase from ZIPATO Your dated sales or delivery receipt showing the date of purchase of the product is your proof of the purchase date You may be required to provide proof of purchase as a condition of receiving warranty service You are entitled to warranty service according to the terms and conditions of this document if a repair to your ZIPATO branded hardware is required within the Limited Product Warranty Period Other than in respect of products for
12. tation of the proof of purchase Upon further request by ZIPATO this warranty card has to be presented too EXCEPT AS EXPRESSLY SET FORTH IN THIS LIMITED WARRANTY ZIPATO MAKES NO OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING ANY IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ZIPATO EXPRESSLY DISCLAIMS ALL WARRANTIES NOT STATED IN THIS LIMITED WARRANTY ANY IMPLIED WARRANTIES THAT MAY BE IMPOSED BY LAW ARE LIMITED IN DURATION TO THE LIMITED WARRANTY PERIOD TO THE EXTENT ALLOWED BY LOCAL LAW THE REMEDIES IN THIS WARRANTY STATEMENT ARE CUSTOMER S SOLE AND EXCLUSIVE REMEDIES AGAINST ZIPATO THEY DO NOT HOWEVER AFFECT OR RESTRICT THE RIGHTS YOU HAVE AGAINST THE BUSINESS YOU BOUGHT A ZIPATO PRODUCT FROM IN NO EVENT WILL ZIPATO BE LIABLE FOR LOSS OF DATA OR FOR INDIRECT SPECIAL INCIDENTAL CONSEQUENTIAL INCLUDING LOST PROFIT OR DATA OR OTHER DAMAGE WHETHER BASED IN CONTRACT TORT OR OTHERWISE HOWEVER NOTHING IN THIS AGREEMENT LIMITS ZIPATO S LIABILITY TO YOU I IN THE EVENT OF DEATH OR PERSONAL INJURY TO THE EXTENT RESULTING FROM ZIPATO S NEGLIGENCE OR II TO THE EXTENT RESULTING FROM ANY FRAUDULENT MISREPRESENTATION ON THE PART OF ZIPATO OR IlI TO THE EXTENT ARISING UNDER PART 1 OF THE CONSUMER PROTECTION ACT 1987 OF THE UNITED KINGDOM SOME STATES OR COUNTRIES DO NOT ALLOW 1 A DISCLAIMER OF IMPLIED WARRANTIES 2 A LIMITATION ON HOW LONG AN IMPLIED WARRANTY LASTS OR THE EXCLUSION OR 3 LIMI
Download Pdf Manuals
Related Search