23158 manual English
Contents
1. limited to the repair or replacement of this product only and does not extend to consequential or incidental damage to other products that may be used with this unit This warranty is in lieu of all other warranties express or implied Some states do not allow limitations on how long an implied warranty lasts or permit the exclusion or limitation of incidental or consequential damages so the above limitations may not apply to you This warranty gives you specific rights and you may also have other rights which vary from state to state If unit appears to be defective within the warranty period please contact out technical support team for assistance Technical Support section in the manual Made in China isa trademark of General Electric Company andis under license by Jasco Products Compary LLC 10E Memorial Rood Oklahoma City OK 73114 wwwjascoproductscom2. Thin Profile Fixed Position Flat Screen TV Mount E User Manual sw ow e Gaal Ga gt 590 Easy to install 3 mounts in minutes 165 Ibs Max Questions Call 1 800 654 8483 M F 7 30am 5 00pm CST NETRA or visit www jascoproducts com os 20 3 vert LISTED Thank you for purchasing this GE product The GE Flat Panel Wall Mount allows you to easily quickly and securely mount your flat screen display to a wall Please review these instructions carefully before beginning installation Please verify the mounting hole locations VESA compatibility of your display to ensure proper installation For further detailed instructions please visit our website at www jascoproducts com SPECIFICATIONS Display Size 42 to 90 Maximum Load 165 Ibs 75kg VESA Mounting Pattern 800mm x 500mm Max Profile 1 25cm TOOLS REQUIRED Phillips Screwdriver Ratchet or Driver with 1 2 13mm socket Drill amp dril bit 1 4 6mm drywall 3 8 LOmm concrete Wall stud locator drywall installation Tools not included WARNINGS 1 Read these instructions carefully before you begin If you are unsure of any part of the process contact a professional contractor or installer for assistance Improper installation can result in injury or damage 2 Use with products heavier than 165 Ibs 175kg may resultin instability and possible injury 3 The wall or mounting surface must be capable of supp
3. he safety bar to prevent bar from being removed A padlock not included can be inserted into the end of nes Safety bor with scfety oppern Bloc incase Safety bor with padlock in place Padlock not included the bar to help prevent theft of your display see Fig 5 IMPORTANT The safety bar should be used at all times to prevent the display from being accidentally knocked from the mount 3 Periodically clean your mount with a dry cloth Inspect all screws and hardware atregular intervals to ensure that no connections have become loose over time Re tighten as needed TECHNICAL SUPPORT For additional assistance Online www jascoproducts com support Email support jascoproducts com Our in house call center is open M F 7 30am 5 00pm CST except holidays and special events For product information troubleshooting and warranty calls 800 654 8483 option 1 For consumer business sales 800 654 8483 option 2 Mailing Address Jasco Products Company Attn CIC 10 Memorial Rd Bldg B Oklahoma City OK 73114 Please contact technical support lusing one ofthe listed options before attempting to ship product returns or warranty requests Failure to do so may delay processing times considerably 1 YEAR LIMITED WARRANTY Jasco Products Company warrants this product to be free from manufacturing defects for a period of one year from the original date of consumer purchase This warranty is
4. ing holes are recessed you will need to use the longer screws IE Gland the spacers Hl 2 Determine the correct diameter of screw to use by carefully trying one of each size M6 and Mal from the hardware kit Do not force any of the screws if you feel resistance stop immediately and try a smaller diameter screw 3 Attach the mount arms to the back of your display using the screws identified in Steps Lond 2 A If you are using the M6 screws you will also need to use the M6 washers LHS screws do not require washers B you are using the longer screws on a display with a curved and recessed back you may also need to use the spacers HI Use one spacer or two spacers stacked asneeded Only use a spacer if necessary Tai ET aa T PEA G or recessed Bocke 4 Attach the mount to the back of your display using the screws identified in Steps 2 and3 if you are using the longer screws on adisplay with a curved or recessed back you may also need to use the spacers IHI provided in the hardware kit Only use a spacer if necessary FINAL ASSEMBLY 1 With the help of another person carefully lift your display and place it on the wall mount plate Do not release the display until the mount arms have securely hooked onto the wall mounting plate 2 Insert the safety bar at the bottom of the mountto prevent the display from being lifted from the wall plate Insert safety stopper into the end of t
5. o avoid cracking or splitting the wood during installation 2 Place the wall plate against the wall and level it using the included bubble level 3 While another person holds the wall plate in position mark two locations per stud for the lag bolts A used to secure the mount ta the wall See Fi ni 4 Drill a 1 4 6mm pilot hole at each marked location 5 Place the wall plate back against the wall and attach it using the lag bolts A and lag bolt washers provided in the hardware kit 2 Fig 21 Do not overtighten these bolts and do not release the wall plate until all bolts are in place ns Ensure that the wall plate Temoins evel aher all bolts are secured CONCRETE INSTALLATION INSTRUCTIONS IMPORTANT For safety reasons the concrete wall must be capable of supporting the combined weight of the mount and the display The seller manufacturer takes no responsibility for the failure caused by walls or insufficient strength IMPORTANT if installing the mount onto a concrete block or brick surface never drill into the mortar between blocks or bricks YOU MUST SECURE THE MOUNT TO THE CONCRETE BLOCK OR BRICK 1 Place the wall plate against the wall in the desired location and level it using the included bubble level 2 While another person holds the wall plate in place mark the four locations for each lag bolt Al on the wall for securing the mount see Fig 3 3 0rillan 3 8 1omm h
6. ole at each marked location Remove any excess dust from the holes 4 Inserta concrete anchor Clinto each hole so that itis flush with the concrete surface see fig 4 Ahammer can be used to lightly tap the anchors into place if necessary 5 Place the wall plate back against the wall and attach it using the lag bolts A and lag bolt washers B provided in the hardware kit See Fig 21 Do not over tighten these bolts and do not release the wall plate until all bolts are in place ne Ensure that the wall plate remains level after all bolts are secured ATTACHING THE MOUNT ARMS TO THE DISPLAY IMPORTANT Use extra care during this part of the installation If possible avoid placing your display facedown as it may damage the viewing surface NOTE This mount comes with a selection of different screw diameters and lengths to accommodate a wide variety of display monitor television models Not all of the hardware in the kit will be used Ifyou cannot find the appropriate screw size in the kit provided consult the manufacturer of your display for more information 1 Examine the mounting holes on the back of your display to determine the correct length of screw to use A Ifthe back of your display is flat and the mounting holes are flush with the surface you will use the shorter screws 1D F from the hardware kit B ifthe back of your display is curved has protrusion or ifthe mount
7. orting the combined weight of the mount and the display if not the structure must be reinforced 4 Safety gear and proper tools must be used Failure to do so can result in injury and or damage 5 A minimum of two people are required for installation Do not attempt to instal this mount alone under any circumstances 6 Follow all instructions and recommendations regarding adequate ventilation and suitable locations for mounting your display Consult the owner s manual for your particular display for more information 7 Seller manufacturer is not liable for damages or injury caused by incorrect mounting assembly or use 8 This product contains small items that could be a choking hazard if swallowed Keep these items away from children This wall mount is for indoor installation only HARDWARE KIT A M8x 63 Lag Bolt x6 B Lagboltwasher x6 j C Concrete anchor x6 D M6x 12 screw x E M6x 30 screw x F M8x 12 screw x we G MBx30 screw bt ee H Spacer x8 1 M6 Washer x4 DRYWALL INSTALLATION INSTRUCTIONS IMPORTANT For safety reasons this mount must be secured to a wood stud capable of supporting the combined weight of the mount and display DO NOT MOUNT TO DRYWALL ALONE 1 Use a high quality stud finder to locate the stud where you wish to install your mount Mark both edges of the stud to help identify the exact center NOTE You must use the center ofeach stud t
Download Pdf Manuals
Related Search