EN - User`s manual ()
Contents
1. 2 Configuration 3 4 Click to the appropriate contact to change the configuration If in case of a light signal with three four lights you set 10 for the address as indicated in the above example the signal occupies addresses 10 and 11 An output configuration belongs to each signal aspect Marks and indicate whether the given output is switched on in its active or inactive status Railway occupancy and feedback reports For indicating railway occupancy you will need a railway occupancy sensor Order no 26301 and S88 feedback module order no 78832 The first S88 feedback module can be accessed on the previously adjusted S88 initial address Such a feedback module can receive 8 inputs Therefore if you use 3 feedback modules if 65 is the initial address their addresses are 65 66 and 67 moving away from the PC interface Each of these modules is capable of reporting 8 input statuses which equals altogether 24 input statuses You may use 127 such modules in total 127 8 1 016 inputs Add an Indicator element to the railway line then edit its properties Contact Indicator Switchboard 10 28 e General ER Connection Fa Operations fal Memory Connection Cancel a Digital System Lenz Digital Plus LI101F lt ancel l Help Address 65 Input 5 Search next free J After setting the address of the feedback report modu2. the name of the device 7 Click on Connect in the main menu Stop on Linaw vf Chaticean Bleck Dhesmeder Send Interval Turret Internat Pol Setches ond Signals Subsequently the application will be able to communicate with the adapter device TrainController will be connected automatically to the interface at the each start of application In general separate connection is not necessary Use of railway switches Please always draw the railway line in the first step Then add the railway switches of which the addresses must be labelled Please double click on the railway switches Right Switch Switchboard 13 15 ES General Connection Condition Connection Digital System Lenz Digital Plus LI101F Address Ey Normal State Pulse Number of Contacts 2 a4 Click to the appropriate contact to change the configuration 1 Please select digital system then give the address of the railway switch 2 If the railway switch operates oppositely to the signal the problem may be eliminated by exchanging the outputs Use of light signals The signals are used similarly to the railway switches It must also be set to the address of the railway switches but a four light Signals need more than one address Four Aspect Signal Switchboard 14 17 Fer General 2 Connection a Condition Connection Normal State L Switch Time o Pulse wv Output Number of Contacts
3. COM E kii Processzorok 22 le AMD Phenom tm 9650 Quad Co i ff AMD Phenom tm 9650 Quad c i n e AMD Phenom tm 9650 Quad Then search for line USB Serial Port under menu point Ports Here you can read that your device is found at the address COM7 after connecting it to the computer Obviously it may vary in case of each computer Older versions of controller applications Please keep in mind that the older versions of TrainController lt 5 5 Rocrail JMRI may not always support port numbers higher than 9 consequently they are able to communicate via ports COM1 COMY In case a port number has to be modified you can do it under Right mouse click gt Properties gt Port setting gt Special Simply adjust it to an unused port number under 10 Basic configuration with Lenz LI 101 tool LI101F Tool LI101F Programming Tool Read and write LI101F Information Lenz Central Unit Information Central Unit Version 3 0 Central Unit ID Unknown ID 16 LI101F Information Version Number 1 0 Service Number 01 XpressNet Device Address 30 New Address Baud Rate 19 200 Baud New Baud Rate Only the basic settings of LI101F interface can be modified with this utility application made by Lenz thus your module supports this application because of downward compatibility Configuration with TrainModules PC Interface application With this device you ca
4. O AAN 10 Guarantee and legal statement cece cece eee ee ee eee eeteeeeetaeaees 11 Features and properties e Can be connected any XpressNet central e Compatible with Lenz LI101 interface e Feedback bus S88 handling e Easy configurable paramteres e Windows Linux and Mac compatible Technical specifications Input voltage 5V USB Standby current 5 mA Dimensions 53x50mm Short description The PC interface allows control the layout thereby enhancing the game experience We can control any locomotive turnouts or an external device from a computer Automatic timetables can be created The first time use Each module will operate with the following default settings at the first use XpressNet address 31 PC Baud rate 19 200 kbit s S88 initial address 65 the previous 64 device addresses are usually occupied Number of S88 modules 1 It is possible to modify these settings either with Lenz s LI101 configuring device or with our application With this latter application the S88 feedback can be also modified Detecting the COM port address In order to enable communication between your device and your computer you must know which communication COM port the device is on For that please open the device manager under Windows Start menu gt Run gt devmgmt msc then Enter pre Portok COM s LPT Sch io kommunik ci s port COM1 E me UF Nyomtatoport LPT1 low ian USB Serial Port
5. TM 54101 PS TRAINTIODULES XpressNet S88N PC interface User s manual 5 998975 300889 2011 BioDigit Ltd All rights reserved It is forbidden to reproduce and or publish the contents of the present document in any form including electronic and mechanical design without the written permission of BioDigit Ltd A N Safety precautions During the operation of the device the specified technical parameters shall always be met At the installation the environment shall be fully taken into consideration The device must not be exposed to moisture and direct sunshine A soldering tool may be necessary for the installation and or mounting of the devices which requires special care During the installation it shall be ensured that the bottom of the device should not contact with a conductive e g metal surface Contents Sa ely PrecaUIONS srian EET E E ON 1 Features and PropertieS ereire NEETER 2 TECNNICALSDECIFHICIUON S norca ETE aO 2 Short dESCHOUON arn airan a a a EEE 2 THE NSt TIME US E aoea a e hase 2 Detecting the COM port AdCCIre SS ccc cece cece ee eeeeeeeeeeeeeeeeeneeees 3 Older versions of controller applications ccc eee c eee eeeeeeeeeeeeeees 3 Basic configuration with Lenz LI101 tool cece cece cece ee ees 4 Configuration with TrainModules PC Interface application 4 Use with TrainController Application ccceeee cece eee eeeeeeeeeees 5 DOWO TOS iarcias AA
6. e Engine 1 ES General Connection gi Speed T ti Digital System Lenz Digital Plus LI101F a Address 3 B Minutes After adjusting the address please also indicate the functions under tab Engine Engine 1 Speed amp Functions W Resources Assign Engine Functions Type klick to change S Decoder 01 On Off Switch Decoder 02 On Off Switch pinion Ere C Dine Number 2 On Off Switch l Push Button Macro Macros Sound File Controlling engines If you are not in editing mode switching Ctri E double click on the previous engine list to obtain the following control panel Here you may see the previously adjusted function buttons below light smoke generator together with your current engine and the speed direction controller The application offers countless additional possibilities The software s Help provides information on further settings and on the use of the application Downloads PC interface configuration utilities http www trainmodules hu TrainController http www freiwald com JMRI http jmri sourceforge net 10 Guarantee and legal statement Each parameter of the device will be submitted to comprehensive testing prior to marketing The manufacturer undertakes one year guarantee for the product Defects occurred during this period will be repaired by the manufacturer free of charge against the presen
7. le please adjust the input to which this Indicator is connected These inputs equal with the numbers of inputs from 1 to 8 Allocation of railway line It is possible to assign a railway line to the feedback report module under tab General by Highlighted track elements Then you may select click by click which railway section should be illuminated together with the feedback module Noise filtering at railway line occupancy One second Timer turning off delay can be found under tab Memory By using it the feedback signal will not blink but it is turned off with a delay of 1 second Contact Indicator Switchboard 10 28 ee General So Connection a Operations A Memory Reset Mode Automatic Manual Timer beginning when turning on Period a Timer beginning when turning off 1 H seconds By Train when train passed the point where indicator is turned on By Train when train passed the point where indicator is turned off By Indicator f Toggle Additional Options Normal State I Forced Reset Engines Engines must be addressed in the same way You must create an engine under menu point Train Create Engine aW Block Schedule Tools Window Hel Then you must display the list of engines by means of menu point Window Train List If you double click on the newly created engine you will see the usual settings Engin
8. n adjust the S88 feedback bus also 1 Adjustment of the already defined L m C ess Se port number When it is opened it Port num will check all of the serial ports E between COM1 and COM20 and Feen saiit offers only that can be accessed Device informations 2 Please load the current settings O Now all fields are automatically Base settings filled You may read the device XpressNet address 31 hardware and software versions at P ouart hs the part Device information S88 settings 3 Please remember to save the desired eee E values after adjusting them S88 module num 1 4 After that unplug the device from the digital centre and from the _ Wiese 3 Ei computer then please reconnect i a XpressNet address address of the device 4 Baud rate communication speed c S88 start address starting address of the feedback system d S88 module num number of modules connected to each other Use with TrainController application 1 Adjustment of digital system ee 2 Add PC interface Die anen 3 Select adapter Lenz LI101F then gs cote adjust PORT number the one you have already read in the device manager and used at the interface configuration In our example it is COM7 4 Please click on OK 5 Please approve the settings here You must be able to see the newly added device in the list 6 If you did not adjust the port the message Offline will appear next to
9. tation of the invoice The validity of the guarantee will cease in case of improper usage and or treatment Attention By virtue of the European EMC directives the product can be used solely with devices provided with CE marking The mentioned standards and branch names are the trademarks of the firms concerned TrainModules BioDigit Ltd Kerepesi street 92 H 1144 Budapest Made in Hungary Tel 36 1 46 707 64 http www trainmodules hu 11 Figure 1 PC USB Roco 10764 Slave Command Station
Download Pdf Manuals
Related Search