Usage Manual - Parts Express
Contents
1. a device is not paired within 2 minutes the transmitter will go into standby mode Note The BT00602 can pair with Bluetooth devices using passkeys of 0000 1111 8888 or 1234 2 Switch on your Bluetooth device and put it in discovery mode Choose the BT00602 once it appears Enter the passkey see Note above and the devices should be paired within 1 minute Once paired a blue LED will flash once every 10 seconds If pairing isn t successful within 1 minute please repeat the steps above Note A Bluetooth device that has already been paired to the BT00602 only needs to be powered on Connection will occur automatically Delete the paired device list With the transmitter powered on double click the MFB button the paired device list contains information for the Bluetooth devices that have been paired with BT00602 After this list is deleted it will be necessary to pair devices according to the steps above The transmitter will go into pairing mode once turned on LED status 1 Pairing mode red and blue light are flashing alternately 2 Standby mode or disconnected blue light flash twice quickly each 5 seconds Page Usage Manual 3 Device connected and paired blue light flash once each 10 seconds 4 Low battery status red light keep on flashing Note When the BT00602 is pairing and the blue LED flashes once that means device pairing is successful If you see the blue light flash twice quickly that means the pairing is not2. successful and pairing will have to be tired again Specifications Bluetooth Frequency 2 4G 2 48G Hz ISM band Bluetooth Version V2 1 EDR class H CSR chip es lt lt a i Support profiles A2DP audio streaming AVRCP device remote control Distance 10 Meters Light Indicator 2 Color LED Red Blue Interface 3 5mm Battery capacity 160 mAh Data encryption 128 bits encrypted Frequency Range 2 402 GHz 2 480 GHz Listen stand by time Up to 8 hours Up to 160 hours Battery tips Fully charge the battery for at least 4 hours prior to first use If the BT00602 has not been used for more than 21 days please charge for at least 4 hours When the LED indicator light flashes red during using or while in standby mode the battery is low and you needs to be recharged as soon as possible Please only use the original charger to charge BT00602 Attention Please read this user manual carefully and use BT00602 correctly at all times by following the instructions Pls keep the BT00602 away from children as it s size could present a choking hazard Clean the Bluetooth transmitter using a soft and dry static free cleaning cloth Please do not use cleaning liquids solvents or sprays to clean it Do not clean it while it is charging Do not dissemble it If you encounter any problems contact your retailer immediately Recharge it once per month even if it
3. LEDs flashing alternately for up to 2 minutes Usage Manual Bluetooth Audio Transmitter Introduction This Bluetooth transmitter is specially used for transmitting audio from your music source MP3 player mobile phone TV etc to Bluetooth enabled devices such as speakers headsets or a Bluetooth receiver Bluetooth V2 1 EDR allows for to 10 meters 33 feet of distance and supports A2DP and AVRCP profiles Up to 8 devices can be paired and stored with automatic connection to the last used device when powere or Operating Guidance Charging 1 Plug the travel charger into an AC outlet connect the USB charging cable to the charger 2 Plug the mini USB connector into the power interface on BT00602 3 While it is charging the red LED indicator light will come on When BT00602 is charged the red indicator light will go out 4 While charging the BT00602 please do not use it Power on When in the powered off state press the MFB button for 3 seconds until the blue LED flashes If the BT00602 hasn t been paired with a Bluetooth device before it will go into pairing mode with red and blue Power down To turn the Bluetooth transmitter off press the MFB button for 3 seconds A red LED will flash three times quickly then goes out The transmitter is no ready to be charged Pairing with Bluetooth devices 1 Power on the transmitter by pressing the MFB button for 5 seconds until red and blue LEDs flash alternately If
4. hasn t been used to maintain optimum battery life Use of a charger other than the manufacturer s originally supplied charger may cause the unit to malfunction or fail In addition product damage with non manufacturer chargers may result in the cancellation of the product warranty Troubleshooting If you can not connect Bluetooth devices according to the above operation please try these steps 1 Ensure the BT00602 is charged and powered on 2 Ensure the connecting device has Bluetooth reception supports A2DP and is on Please refer to the manual of the Bluetooth reception device for reference 3 Make sure the distance between the BT00602 and Bluetooth device is within 10 meters Storage Do not disassemble the unit for any reason This may damage the unit accidentally and void the manufacturer s warranty Please store the unit away from dust heat and areas where it might accidentally fall or other damage may occur Page 2
Download Pdf Manuals
Related Search