Home

WR-10X

1. Radar setting 210 Azimuth offset degrees increase o rotate map CW 32 Elevation offset decidegrees angl to set home positi Gate offset number of gates 90 meters range resolution w Enable noise fiter Maral Automatic Noise level Log threshold 1200 Pube number Noise calculator Matched Fiter At the beginning At the end Never Loss dB Tune indicator threshold J Save profile 9 YO Load profite Fig 3 25 Signal Process folder Radar calibration is the section of the folder which includes parameters related to the radar calibration Putting a flag on the K Radar calculation box the radar constant at 1 Km range Radar constant is calculated using all other parameters otherwise it is entered as input parameter together with Receiver slope parameters In this second mode to be used when all radar parameters are not available the radar constant value necessary for the reflectivity calculation in dBZ is entered manually The correct constant value is that which allows to extract measured reflectivity values related to the real situation and can be extrapolated only through another calibrated system covering the same observation area lf the constant is calculated putting a flag on K radar calculation the calculation procedure and the meaning of the parameters are described below The WR10X weather radar measures a parameter called Reflectivity Z representing it ina polar space on logarithmic sc
2. User Manual Server Document code OM 11242 10 01 The copyright in this document is the property of Eldes The document is supplied by Eldes on the express understanding that it is to be treated as confidential and that it may not be copied used or disclosed to others in whole or in part for any purpose except as authorized in writing by Eldes Eldes s r l Via Di Porto 2 b 50018 Scandicci Fl ITALY vann EDES User Manual Server List of Acronyms Meaning Compact Disk kon n PLAN Local rea Network Pei PlanPositon ndcator OOO ELDES Document code OM 11242 10 01 Proprietary Information Page 1 of 118 WR 10X User Manual Server Summary 1 INT RODUG PION poet et tk a ae E EEE E a 7 2 SOFTWARE PACKAGE INSTALLATION ii kat sl a lk ket e at a e kak ke a a kak n kk pa a te e e e a a a a ao e 7 2 1 INTRO BIYE TION ki it ek tk in av n eu ke site fr a k ep ab v pi fi a a ero bot a kt bik en tk ked kaa ek n tea 7 2 2 INSTALLATION PROCEDURE cccceccecceccecceueeceuseeuseusuuseuccuceceueeuceuceueeueeuesuusassuesaesausenseeseeeeueans 7 221 WR 10X ISAM ANNO keesis yon ko so ose isi ase dete dosou ii p re poko tes sisie te feb p te fini s ak pete bik kn EEDE r NE ks ole 9 2 2 2 License Server Service InstallatiON ccccccecccccceccceeeseeeeeeeeeseeeeeeceeeesseeeeeeeeeeessseeaseeeeeeessaaegsess 14 229 Dia A IG A NON se koka pasi an de afe ne ke ae d inn in ee a tl a d ele ia A b e e
3. tuning terminated returning 75 value Opening data serial port Stopping data trasmission Setting level 1 elevation 1 0 degrees elevation setted succesfully Starting data trasmission Starting data acquisition at 1 0 degrees data acquisition process finished succesfully data acquisition process at 10 decidegree finished Stopping data trasmission Setting level 2 elevation 3 0 degrees elevation setted Sica Starting data trasmission Starting data acquisition at 3 0 degrees data acquisition process finished succesfully data acquisition process at 30 decidegree finished Stopping data trasmission Setting level 3 elevation 5 0 degrees elevation setted ak ak Starting data trasmission Starting data acquisition at 5 0 degrees data acquisition process finished succesfully data acquisition process at 50 decidegree finished Stopping data trasmission Setting level 4 elevation 6 0 degrees elevation setted succesfully Starting data trasmission Starting data acquisition at 6 0 degrees data acquisition process finished succesfully data acquisition process at 60 decidegree finished Stopping data trasmission Returning antenna to the Home position succesfully succesfully succesfully succesfully Pointing to 0 0 degrees in azimuth for level 1 pointed to 0 0 degrees succesfully Setting the start elevation for level 1 0 0 degrees Page
4. ELDES Document code OM 11242 10 01 Proprietary Information Page 83 of 118 gt L Mi oc User Manual Server 10 Layer Preview Fig 5 Once all values have been entered in the related fields click on the Save button to save the new layer adding it to the list button and follow the same procedures To modify an existing layer click on the mentioned for the layer adding Document code OM 11242 10 01 ELDES Proprietary Information Page 84 of 118 vann EDES User Manual Server 5 3 Products filter The Products filter section allows to choose the display type between e Display of images generated through clutter filter application putting a flag on the Without clutter option e Display of images generated without clutter filter application putting a flag on the With clutter option The Range drop down menu displays all range values related to the available radars in the system After selecting one of these the related layer image is displayed The drop down menu below the Range whose name can be changed and which can be configured in the Registration section related to the involved product displays sizes and the related image in the example shown in the following figure the size is expressed as elevation in tenths of degrees lf this control is disabled deselecting the proper check box the images movie loop will show a time sequence of the product apart from the content of the variabl
5. Offset control X Offset Y Offset Georef control Georeferentiation file DIR FIND image Dimension Georeferentiation file Georeferenziazione_Tav_lfalia_Out txt image Type Georef data conversion file DIR Georef data conversion file Tav ala Out afine fxt Fig 5 37 Map Creator Interface The SET control allows to determine the name the graphical format and the path of the Background Map file to generate The GEOREF CONTROL controls allow to find the path of the georeferentiation and data conversion files necessary for the Background Map files beginning from the not georeferenced cartographic database possibly included in the software package ELDES Document code OM 11242 10 01 Proprietary Information Page 99 of 118 WR 10X User Manual Server The default name related to the georeferentiation and data conversion files possibly included in the software package are automatically specified in the GEOREFERENTIATION FILE and GEOREF DATA CONVERSION FILE text boxes The default search path for both files above mentioned is the following Cartografia_Italia and can be specified through the FIND controls the Cartografia_Italia folder is an example which marks the location of the not georeferenced cartographic database possibly included in the software package The DEG MODE and DMS MODE controls together with the related text boxes allow to edit the coordinates of the map centre LAT LON coordi
6. Selecting a radar or a scan it will be possible to enter or modify the related configuration parameters through the folders which will appear on the right side The Fig 3 6 shows an example in which in DataAcq Server three different scan modes have been prepared The scheduler has been activated only on one scan and it will run the scan at the specified day and hour RadarjiScan list Yo Schedule Mext Run Time Last Run Time Status Radar Monte Lussari a Scan Invernale Nok scheduled Never Never i Scan Estiva Mat scheduled Mever Mever Fig 3 6 Scans 3 1 2 Scan Mode In the Scan Mode folder see Fig 3 7 it is possible to select characteristic parameters of each scan The main parameters which can be set are the scan type PPI and or RHI through the relative check box For each type it s possible to select the operating Range which shows the radar range in distance and the Range step that allows to specify the scan range resolution The Range step can be set in function of the specified Range according to the Tab 3 1 Document code ELDES OM 11242 10 01 Proprietary Information Page 25 of 118 EP DES van User Manual Server nication vanced work mode Scan Mode PPI RAI Ri PPI Elevation and azimuth setting a tep 1 1 5 a tep 2 3 Range 105 Km a al tep 3 4 5 Range step 450 m a tep 4 a tep 5 a tep 7 a tep 8 tion s tion s tion s tion s tion s Elevation step 6 tion s tion s tion s tio
7. The sixth column shows the REAL Decision Threshold value of the last scan calculated according to the LOW Threshold value currently set The seventh column shows the REAL Min extreme of the LOW Threshold range value calculated measuring the StdDev of the last scan which has been run classified as Clutter The eighth column shows the REAL Max extreme of the LOW Threshold range value calculated measuring the StdDev of the last scan which has been run classified as Clutter The ninth column shows the number of times which a specified scan has been launched and it also shows the number of samples used in the calculations to obtain the average values The tenth column shows the THEORETICAL Decision Threshold value calculated according to the LOW Threshold set making an average between data of all scans which have been run The eleventh column shows the THEORETICAL Min extreme of the LOW Threshold range value calculated making an average of the StdDev of all scans which have been run classified as Clutter The twelfth column shows the THEORETICAL Max extreme of the LOW Threshold range value calculated making an average of the StdDev of all scans which have been run classified as Clutter ELDES Document code Page 60 of 118 Proprietary Information OM 11242 10 01 vann EP DES User Manual Server 3 4 Archive The Archive folder includes all parameters relat
8. RHI XXX AAAAMMGGHHMM B RRRP rrrr eeee AAAA C z or RHI XXX AAAAMMGGHHMM B RRRP rrrr eeee AAAA U z where XXX Network and radar number identifier AAAAMMGGHHMM Acquisition data start time of the radar scheduler B Not used RRRR Range expressed in hundreds of meters rrrr Range resolution range expressed in meters eeee Elevation resolution expressed in decidegrees AAAA Azimuth expressed in decidegrees C or U Data type C for cluttered data U for uncluttered data ELDES Document code Page 52 of 118 Proprietary Information OM 11242 10 01 vann EDES User Manual Server For example the integrated data file with the file name RHI A00 201112011256 B 0360 0150 0005 2800 U z referred data acquired at 12 56 on 01 December 2011 from radar AOO The range is 36Km the range resolution is 150m the elevation resolution is 0 5 oversampling the azimuth selected is 280 Overall the data divided into 36Km 150m 240 cells in range columns while the information extracted from the file name is not sufficient to determine the number of rows The missing information concerning the initial and final elevations of the scanned sector on the elevation axis however are available in the header of each row Each row of the matrix is preceded by a header of 24 numeric fields The fields contained in the header are as follows HEADER HEADER_TYPE HEADER_TIMESTAMP_Y HEADER_TIMESTAMP_MG HEADER_TIMESTAMP_HM HEADER TIMEST
9. WR 10X User Manual Server Customization Toolbars Commands Options Toolbars i Toolbar iw Status Bar B Main Menu Rename Custom 4 Delete Reset Fig 5 23 New customization The new customization can be removed clicking on the Delete button or it can be renamed clicking on the Rename button Any possible change made to the new customization can be undone clicking on the Reset button Commands folder is shown in the following figure Customization Toolbars Commands Options Categories Commands Unassigned Items Current Page 1 OE Total Pages 1 Zoom Factor 100 JA Search VS Open E Description Fig 5 24 Customize Commands Options folder allows to set further options concerning the display ELDES Document code OM 11242 10 01 Proprietary Information Page 93 of 118 EP DES van User Manual Server Customization Toolbars Commands Options _ Personalized Menus and Toolbars Always show Full menus t Show Full menus after a short delay Reset my usage data Other Large icons jst Show ScreenTips on toolbars jt Show shortcut keys in ScreenTips Menu animations System default Fig 5 25 Customize Options Putting a flag on the Large icons option the menu bar icons will be displayed in a larger size File view Background Preview mex ni Fig 5 26 Large icons lf i
10. 0 0 180 21 6 Km 150 m 0 180 21 6 Km 300 m 0 180 21 6 Km 450 m 0 180 36 Km 150 m 0 N 180 36 Km 300 m 0 180 36 Km 450 m 0 180 72 Km 300 m 0 180 72 Km 450 m 100 180 108 Km 450 m Fig 3 9 Scan Setting 3 1 3 1 Scan Setting left block The left block contains the Settings section the possible choices are e Do not radiate the radar does not radiate power e Radiation off at end scan at the end of the running scan the radar radiation is set to Off e Save raw data in r file raw data are saved in a binary file with r extension The file is saved in the following address C Programs WR 10X DataFiles DATA RAW e Save raw data in text file raw data are saved in a text file The file is saved in the following address C Programs WR 10X DataFiles DATA RA ELDES Document code OM 11242 10 01 Proprietary Information Page 29 of 118 EP DES van User Manual Server Tuning After at the end of each scan the radar tunes again Before at the beginning of each scan the radar tunes again recommended None radar does not carry out tuning procedure Enable Pointing for Tune this check box is automatically flagged if one or both Sector Blanking in the PPI section of the Scan mode tab is selected Azimuth direction type the Azimuth angle value 0 360 degrees related to the antenna desiderated direction to be kept during the tuning activity LDL A Note The chosen Azimuth angle value must n
11. 3 4 2 General configuration Action Archive configuration General configuration Show DataArchiveTsk video log Save DataArchiveTsk log on file DataArchiveTsk log C Display window application Fig 3 34 General configuration Log DataArchiveTsk WR 10X ser Manual Server The purpose of this log file is to save all messages coming from the DataArchiveTsk module on a file This function can be useful in case of system fault to analyze the archive process point in which a possible problem has occurred or occurs P DataArchiveTskl Blocco note Fie Modifica Formato Visualizza 00 Page 62 of 118 archive action required Executing action on PPI product Retrieving z Tiles 3426 Tiles found Retrieving GIF files 1713 files found Retrieving TIFF Tiles a Tiles found Retrieving BMP Tiles a Tiles found Retrieving PNG Tiles a Tiles found Retrieving JPEG Tiles a files found 5139 files found to archive sorting files found O x archiving file C Program Fileskwa lOXxADataFilesXPPINPPI 200807091420 B DQ00 C GIF File archived successfully Archiving Tile oe Fi lesswR LOx DataF1 les PPISPPI 200807091420 B6 0000 c Z LI File archived success archiving file Soares Fi less wR LOes atari less PPISPPI 200807091420 B 0000 U Z File archived successTully Fig 3 35 Log DataArchiveTsk ELDES Proprietary Information Document code OM 11242 10 01 mann EDES
12. OM 11242 10 01 Proprietary Information Page 101 of 118 WR 10X User Manual Server MARK CREATOR Marca a 72Km Range Ticks Numbers Fig 5 40 Mark Creator Interface The SET control allows to specify name format and path of the graphic file to generate The RANGE control allows to specify through a proper text box the radial size of the polar mark to generate expressed in Km The TICKS NUMBERS control allows to specify through a proper text box the number of concentric circles and related labels which must be displayed in the polar mark Clicking on the DRAW button the generation routine of the preview will be activated At the end of the generation routine the polar mark is represented in the proper window The following figure shows the preview generated by the application for a range of 72 Km and for 12 Ticks MARK CREATOR ENLA j C Program Files WR f Ox Prova PNG Range 72 00 Km Ticks Numbers 12 Ticks Fig 5 41 Mark Creator Preview ELDES Document code Page 102 of 118 Proprietary Information OM 11242 10 01 man EP DES User Manual Server Only at the end of the preview generation routine the application make the SAVE button available on the graphic interface Clicking on this button the graphic file will be actually generated 5 5 4 3 Layer Creator Layer Creator is an application intended for the georeferenced layer creation of different type A proper interface allow
13. The second section allows to choose if the settings related to a second level product derived product among those registered and so available in the proper drop down menu have to be applied to all other second level products The server type installation does not manage second level products so in this case the second section does not have any effect ES Products View Settings Product Settings Enable common view for products Product of reference VMI Derived Product Settings L Enable common view for derived products Derived product of reference Fig 5 36 Product view settings ELDES Document code Page 98 of 118 Proprietary Information OM 11242 10 01 man EP DES User Manual Server 5 5 4 Utility Selecting Utility from the menu bar the following choices will be available e Map Creator starts the application allowing the background maps creation which can be used as layer e Mark Creator starts the application allowing the polar marks creation which can be used as layer e Layer Creator starts the application which allows georeferenced layer creation of different type 5 5 4 1 Map Creator Map Creator is an application intended for layer creation of Background Mark The following figure shows the configuration interface related to this application Background Map Name L Deg mode LAT Radar LON Radar Dms mode LAT Radar 000 2 00 m 0000 s LON Radar 000 2 00 m 0000 s Range 36 00 Km
14. User Manual Server 3 4 3 Action The Action folder includes all parameters related to actions that have to be carried out on data General configuraton Action Archive configuration Scheduler Archive action Archive gt Delete No action Action on flesplus 1 days old ones Fig 3 36 Action The Archive action box includes the following options e Archive it archives data e Delete it deletes data e No action no action to be carried out The Action on files plus n days old ones option allows to select the files on which the action previously selected in the Archive action box has to be carried out For example entering a value of 30 in the Action on files plus n days old ones field and putting a flag on the Delete button in Archive action option data files older than 30 days will be removed that is only those related to the last month will be stored ELDES Document code OM 11242 10 01 Proprietary Information Page 63 of 118 EP DES van User Manual Server 3 4 4 Archive configuration In the Archive configuration folder is available a list including all information related to the registered products on which the archiving rules have to be applied in order to select the item on which the desired action has to be applied it will be necessary to put a flag on the Enable column For WR10X CE configuration the RHI line is not present All items on which it is possible to apply the above menti
15. for the current image formatting in a proper print preview or saving in a different graphic format for further details refer to par 5 5 1 1 5 5 1 1 Image management Selecting File Image management a window as shown in the following figure will appear Preview File View Background A gt ld SB Cy 7 A ioo Wa lE amp Z G O Current Page 1 Total Pages 1 Zoom Factor 100 5 A A Vie g start osta inviata M P Manuale_Server am PP tug OM 1 2 04 lataAcq Data lataview a Preview Fig 5 16 Image management ELDES Document code OM 11242 10 01 Proprietary Information Page 89 of 118 EP DES anan User Manual Server File Menu selecting File from the menu bar of the Preview window the following options will be available f Preview View Background Page Setup Print Print Export Document Send via E Mail File L4 a f ta Exit Fig 5 17 Preview File menu Page Setup This opens a page setting window typical of Windows in which it is possible to set format alignment horizontal vertical printer trays and the page layout Print This opens the print window typical of Windows in which it is possible to select printer pages and number of copies Print Prints the document directly Export Document This allows to select the format in which image is intended to be exported the possible choices are PDF
16. 07 2010 to 06707 2010 w Manual selection From O4 04 2010 si to 04 04 2010 vil L lense Jean a l NE D WR 10x 4rchive DIIWR 10XlEvento 2010 04 04 i i Map settings i w Background i wi Radar Image Nations i 4 Regions i Provinces i Municipalities l vi Cities H vi Cities amp Town Rivers i As k l lt r p f l ga m B ieee a fema foma fioe fom EE eS Products fiter e Wa N se KE kk a pa w ion TO AR oo 721 End loop delay sec l2 with ch Nok Use iD B VMI AO0 201004042142 8 0720 0000 C GIF Fig 5 47 Zoom image example 2 6 Clutter areas display It is possible to display in the DataView also the cells which included clutters and that the signal processing removed during the images de clutter In order to accomplish this it is necessary to modify the colortbl PPl txt file or the colortbl RHI txt file according to the product on which it is intended to activate the function Both files can be found in the C Program Files WR 10X Bin Colortb path A modified color table example is shown in the following figure 000 001 tE 003 004 a Sls La m n rs OoOomF mo 000 208 0 8 24 000 208 16 120 120 000 208 176 ZOO 299 Fig 6 1 Modified Color table It will be sufficient to modify the 001 line enter
17. 10 01 vann EDES User Manual Server e HEADER_AZIMUTH Azimuth position at the end of the specified ray This position is expressed in steps of 11 bit encoder integer value between o and 2047 e HEADER AZIMUTH IN Only predisposition for future use in azimuth sector scan type For PPI scan type this field is equal to HEADER_AZIMUTH e HEADER_AZIMUTH_OUT Only predisposition for future use in azimuth sector scan type For PPI scan type this field is equal to HEADER_AZIMUTH e HEADER _ELEVATION Antenna angle elevation point for the PPI acquisition This field is expressed in decidegrees integer value between 0 and 1800 e HEADER ELEVATION IN For PPI scan type this field is equal to HEADER_ELEVATION e HEADER ELEVATION OUT For PPI scan type this field is equal to HEADER_ELEVATION e HEADER _PULSEWIDTH Transmitted pulsed width expressed in nanoseconds integer value on 4 digit e HEADER _PRF Transmission pulse repetition frequency expressed in Hz 10 integer value on 4 digit with default value 8000 Hz 10 e HEADER_RANGE Acquisition selected range expressed in hundreds of meters integer value on 4 digit e HEADER_RANGESTEP Acquisition selected range step expressed in meters integer on 4 digit e HEADER_AZIMUTHSTEP Integrated selected azimuth step expressed in decidegrees integer on 4 digit e HEADER_AZIMUTHSPEED Average antenna azimuth speed measured on complete revolution This field is expressed in dec
18. 18 of 118 Proprietary Information OM 11242 10 01 WR 10X User Manual Server Closing Application i X Cancel back to the application main window without performing any action Fig 2 16 License Serve Closing Application Click on the Close the Application and Stop the Service buiton Manually start the service by launching the LicSrv exe file on the Eldes License Server path see Fig 2 17 lb a IE License Server Organizza Indudinellaraccolta Condividicon Masterizza Nuova cartella BE Hil Nome Ultima modifica Tipa Dimensione W it 10 02 2012 15 34 Cartella di file E LicSrv exe 25 11 2011 09 35 Applicazione 80 KE Es LicSrv exe config 16 01 2012 17 44 XML Configuration File 1KB Fi LicSrvULexe 25 11 2011 09 42 Applicazione 160 KB Fig 2 17 LicSrv exe file Confirm the Start of the License Server service by clicking Si on the Fig 2 18 asw OO Fig 2 18 LicSrvUI starting Document code ELDES OM 11242 10 01 Proprietary Information Page 19 of 118 EP DES anan User Manual Server The License Server Control Center window appears see Fig 2 15 Make sure that the license file provided by Eldes is present in the PC Server otherwise copy it in a PC Server folder Click on the Open button L the Fig 2 19 appears ve Preferiti Nome Ultima modifica Tipo ME Desktop E 10913 00020 lic 16 01 2012 17 36 License J Download L i a a je Risorse recent Raccol
19. 2 19 LICENSE FILE SELECTION akte kb kt kte kaa kaa kaa aa aa aa aaa aaa aaa aaa tea aaa tea seseaeesaesaeassoosoesoesoesonsoesoesseosnoon 20 FIG 2 20 LICSRVUI SAVING 556045 cecehssdicts sec ccnetecdestepbicdatetalocsseideedeusiasddbeagdeedatesabedbaeonsedtuetaciebsacdecdatatess 20 FIG 2 21 ACCESS FROM START MENU kk bk tb kt kt takte kwake kaa aa aaa aaa ae aaeaaaaeeasaeoesesoesesoesesoesesoooesoooesaoonsoooun 21 FIG 3 1 DATAACQ MAIN WINDOW na kb kk kt kaka ea kaa ka aaa aka aa aaa aa saaa saeeaaaeeesaeoeseeoesesoesesossesoooesooonsaoonsoonn 22 FIG 3 2 SCAN FOLDER ke tin tanta tka lan aka n a n tet n e n e a tk ee tn aie ee 23 FIG 3 3 RADAR SETTING tt af ik adilt kt zaf n tl ko ek l lt ja n na eki ka ed n ie ki la n a ann 24 FIG 3 4 RADAR NAME AND SCAN ei et en a n ei at an n a e a eee e ie EI ak e nnn 24 FIG 3 5 ADD REMOVE SO AN 2 ostil m toti antandi lott kaa tit avk anka dl al ka ka aa n ok anka kd l e ka tk en en 25 FO OO CAN ente n t palan a a lt ab pi ni a ton en n e n e ae kf n bn n es n n e din ee ee eee 25 eC es ar SCAN MODE ian mt rilasion ea a l ae a en e ee Se ee oT ae 26 FIG 3 8 AZIMUTH AND ELEVATION STEPS bk bl tt kte kat kaa aa aa aaa aaa aaa aaa taa ae aaaeeaeseesaesaesaeseeseesoasoesoasoesoesseoounen 28 Cs SCAN SETTING eieren ii tett tt ae sti EE AE Ee a tk ak kt a e A oe 29 FIG 3 10 CLUTTER FILTER SETTINGS 00 bab lat takte teka tata aaa aaa aaa aaaaasessesseseeseeteeseeseesoesoesoesoesossoesonesnnannnn 33 FIG 3 11 GOM
20. 223 123 114 87 69 67 106 58 88 68 115 77 20111201 130012527 18 224 35 23 223 136 163 223 123 111 81 71 69 86 56 87 72 115 76 20111201 130012542 19 224 35 34 223 136 164 223 124 110 67 71 72 104 59 87 69 113 7 20111201 130012542 20 224 35 27 224 138 162 223 123 105 76 68 63 93 58 86 71 112 78 20111201 130012542 21 224 35 29 223 142 161 223 125 109 74 71 67 104 58 87 73 113 7 20111201 130012542 22 224 35 27 225 141 162 223 125 107 73 71 68 95 60 86 76 111 75 20111201 130012542 23 224 35 26 224 142 161 224 123 111 89 74 67 104 58 88 74 111 74 Fig 3 27 RAW file structure 20111201 130012511 20111201 130012511 20111201 130012511 20111201 130012511 20111201 130012511 20111201 130012511 20111201 130012527 20111201 130012527 Weonauw Se wno PJ Nm nm w vI aS KI Ko Vv jwi Ww Vi pw y Ww ho LAY O a Nm yJ a L oo oo J yo KI Nm a ss SS S N N Mn Mn The RHI raw text file format is very similar to the PPI raw text file format described above ELDES Document code Page 48 of 118 Proprietary Information OM 11242 10 01 vann EDES User Manual Server The fourth column shows the fixed azimuth value of the involved pulse The fifth column shows the elevation value of the involved pulse expressed in number of stepper motor on the elevation axis The file name format for the raw text file is described below PPI XXX AAAAMMGGHHMM B RRRR rrrr aaaa EEEE R txt or RHI XXX AAAAMMGGHHMM B RRRR rrrr a
21. A E LA RHI A B DataAcq A 2 DataView A av W w LA i Register Clear Import reg file Modify i Save and Exit t Save 1 gt 3 i Save profile i Load profile Fig 3 39 Registration folder This folder is composed of two sections Registration and Manage registration which have the function to respectively add a new product to the system and modify an existing product ELDES Document code Page 66 of 118 Proprietary Information OM 11242 10 01 vann EDES User Manual Server 3 5 1 Registration section In the Registration section it is possible to enter data necessary to integrate a new product in the system It is possible to manually carry out this operation choosing the Manual registration option or importing a registration file identified by the rwx extension clicking on the Import reg file button and selecting the desired file Once the file including the necessary information has been imported all parameters will be filled with the information read It will be possible at any time to manually edit the fields previously entered putting a flag on Manual registration Once all fields have been correctly filled it is possible to add a new product clicking on the Register button the application will automatically process the informative content entered and the list in the Manage registration section will enlarge with the product which has been now registered On the contrary clickin
22. HTML Text CSV MHT Excel Rich Text Graphic Selecting each of this entries a window allowing to set the related parameters before exporting will appear File View Background Page Setup Ti Print Li A Print Export Document P PDF File Send via E Mail HTML File J Ext MHT File RTF File Excel File C5 File Text File Image File Fig 5 18 Preview export format ELDES Document code Page 90 of 118 Proprietary Information OM 11242 10 01 vann EDES User Manual Server Send via E Mail This allows to select the format in which the image is to be exported in order to be able to send it via e mail Possible choices are PDF Text CSV MHT Excel Rich Text Graphic Selecting each of this entries a window allowing to set the related parameters will appear then Outlook will automatically be opened together with a pre set e mail with the exported document attached File wiew Background Fage Setup EJI TAJA Print Print Send via E Mail b PDF File Ly a Ly Export Document pi Exit MHT File RTF File Excel File CS File Text File Image File Fig 5 19 E mail format Exit Closes the Preview window View Selecting View from the menu bar of the Preview window options shown in the following figure will be available These have different controls related to the page display settings for
23. Pfannenberg di Pico Technology oe E E A Skype Ji WR 10X Dispositivi e stampanti e DataAcg Dataview Programmi predefiniti M RCU TS M SysCfa Guida e supporto tecnico Fig 2 21 Access from Start menu ELDES Document code OM 11242 10 01 Proprietary Information Page 21 of 118 EP DES van User Manual Server 3 Data acquisition and signal processing setting DataAcq Data Acquisition and Signal Processing manager software package allows to enter data in order to manage the radar configuration To launch the software click on DataAcq link icon a created on the desktop or select from the menu Start All Programs WR 10X DataAcq Once the program has been launched the main window including the following sub folders will appear e Scan e Signal process e General e Archive e Registration ID x X scar Archive ae Registration Radar Scan list Sched Next LastR Status Scan mode B Default Radar Scan Mode PPI RHI Scan 0 INotsc Never Never J PPI Elevation and azimuth setting F RHI V Elevation step 1 0 ae a C Elevation step 2 C Elevation step 3 Range step 300m Elevation step 4 C Elevation step 5 C Elevation step 6 C Elevation step 7 C Elevation step 8 C Elevation step 9 C Elevation step 10 Azimuth velocity degrees sec 20 Azimuth resolution degrees 3 F Save and Exit Save Exit h Sa
24. Square root function SIN Sine function ELDES Document code OM 11242 10 01 Proprietary Information Page 69 of 118 EP DES anan cosi ASINI ACOS ATANT COTANI TANI PI AZIMUTH DISTANCE RANGE VARIABLE IMGINFO OFFSET LAT LON Page 70 of 118 User Manual Server Cosine function Arc sine function Arc cosine function Arc tangent function Cotangent function Tangent function Pi constant Macro returning the angle position of the cursor on the azimuth axis Macro returning the radial distance of the cursor from the radar site according to the range Macro returning the related parameter taken by the file name Macro returning the related parameter taken by the file name Macro returning non numerical information on the pixel value pointed by the cursor Macro returning the elevation offset value corresponding to the radar site height and available in the application xml configuration file for products display this parameter can be configured by the Radar settings at the radar heights entry see para 4 5 3 Macro returning the radar site latitude available in the application xml configuration file for products display this parameter can be configured by the Radar settings at the lat radar site entry see para 4 5 3 Macro returning the radar site longitude available in the application xml configuration file for products display this parameter can be configured by the Radar settings
25. This is the reason why these parameters are chosen only AFTER an observation period in clear air in which these areas are estimated The DataAcq software includes some automatic calculation tools which allow to quantify these parameters in order to carry out a correct estimation Declutter filter setting The following figure shows the window related to the declutter parameters setting The declutter can be disabled removing the flag from Enable declutter The Low Threshold field defines the typical StdDev value below which each cell will be defined as clutter cell The High Threshold field defines the typical StdDev value above which each cell will be defined as weather signal cell The Recovery windows dimension field defines the dimension matrix of n cells x n cells of the recovery mask used during the weather PPI processing for the filtering of cells with intermediate StdDev ELDES Document code Page 32 of 118 Proprietary Information OM 11242 10 01 WR 10X User Manual Server PPI eiai Clutter filters Enable declutter statistical filter Enable dutter map Clutter map update 5 Low threshold ii High threshold 3 Recovery windows dimension Settings Drag a column header here to group by that column Decision Th Height Thre Range Range Step a 98 180 21 6 Km 30 m 98 180 21 6 Km 150 m 93 180 21 6 Km 300 m 98 180 21 6 Km 450 m 938 180 36 Km 150 m 93 180 36 Km 300 m 93 180 36 Km 450 mi
26. algorithm of data related to the RHI scan uses a fictitious resolution amplified with a factor 6 if compared with the real resolution of the elevation cell corresponding to a radar beam width of 3dB This system assures a higher definition on the involved phenomenon even maintaining an exact estimation of the reflectivity value and it is possible according to the high number of available samples for each real resolution cell The Bright band detection allows to search in the specified azimuth step and elevation range the quote of the reflectivity peak that is characteristic of the RHI product see RHI Product Generator User Manual Finally the Elevation resolution allows to perform the elevation oversampling in the same way of the Azimuth resolution During the scan it is possible to set up to 10 steps which can be selected putting a flag on the related Elevation step n box for the PPI and to the Azimuth step n box for the RHI Clicking on the elevation or azimuth value it is possible to modify it This value is expressed in degrees All steps can be enabled at any time together with the related values and if it would not be necessary to manage any of them later it will be sufficient to remove the flag without changing the configured value ELDES Document code OM 11242 10 01 Proprietary Information Page 27 of 118 EP DES PPI RHI WR 10X User Manual Server Elevation and azimuth setting Elevation and azimuth setting Elevati
27. character color char color and the characters width char width and the type of the city to display cities type The cities type control makes cities capital of the province and cities amp town main cities and towns options available the second choice enables a control intended for the setting of a threshold related to the number of inhabitance town population Below a specified number cities will not be displayed CITIES black vi L marnm char color 110 char width cities v citiestype cities town population The Binary File Generation option is not used Document code OM 11242 10 01 ELDES Proprietary Information DEFAULT Page 107 of 118 EP DES van User Manual Server As regards the DEM layer it is possible to specify in RGB format edges of the chromatic scale used to represent altimetry on the ground G_IN G_OUT and edges of the chromatic scale used to represent depths of the sea areas S_IN S_ OUT Usually it is preferred to use as regards the sea representation only one color in this case S_IN S OUT must be imposed Colors can be selected using the proper SETCOLOR controls GROUND COLOR MAP INIT F XX GROUND COLOR MAP INIT Colori di base Colori di base Colori personalizzati ist fT a a ET l A a FENM onalita osso Saturazione fi 74 Verde 210 mon ere Colore L Definisci colori personalizzati gt gt unita Luminosit 120 Blu 220 koni
28. contained in the integrated file z PPI XXX AAAAMMGGHHMM B RRRR rrrr aaaa EEEE C z or PPI XXX AAAAMMGGHHMM B RRRR rrrr aaaa EEEE U z where ELDES Document code OM 11242 10 01 Proprietary Information Page 49 of 118 EP DES anan User Manual Server XXX Network and radar number identifier AAAAMMGGHHMM Acquisition data start time of the radar scheduler B Not used RRRR Range expressed in hundreds of meters rrrr Range resolution range expressed in meters aaaa Azimuth resolution expressed in decidegrees EEEE Elevation expressed in decidegrees C or U Data type C for cluttered data U for uncluttered data For example the integrated data file with the file name PPI A00 201112011256 B 0360 0150 0010 0010 U z referred data acquired at 12 56 on 01 December 2011 from radar AOO The range is 36Km the range resolution is 150m the azimuth resolution is 1 oversampling the elevation selected is 1 Overall the data divided into 36Km 150m 240 cells in range columns and 360 1 360 cells in azimuth rows Each row of the matrix is preceded by a header of 23 numeric fields The fields contained in the header are as follows HEADER HEADER_TYPE HEADER_TIMESTAMP_Y HEADER_TIMESTAMP_MG HEADER_TIMESTAMP_HM HEADER_TIMESTAMP_S HEADER TIMESTAMP ms HEADER INDEX HEADER SCANTYPE HEADER AZIMUTH HEADER AZIMUTH IN HEADER AZIMUTH OUT HEADER ELEVATION HEADER ELEVATION IN HEADER ELEVATION OUT HEADE
29. eee ae apeti ano petet anan ri rasa 86 5 13 COLOR MANAGEMENT BAR ki bl bbl bk tt kt ka aa kaa kaa kaa aa aa aaa aa aaa tea aaeeaeeeseesaeoeseeseesessesoaseosesoesonsonousononnn 86 5 14 DISPLAY WITH TOOLTIP it tt tt kt at kw kw kw ka kaa kaa kaa aaa aaa aaa aaa aea aa eaaesaesaesaesoesoeseeseesoasoesoesoesseosooounn 87 5 15 DISPLAY WITH ZOOM kk bk kt tk kt kat aa aa ka kaa aaa aaa aaa aaa aaa aaa aaa aaa asa eeaesaesassaesaesoosoeseeseesoasoesoesoesseosooannn 87 5 16 IMAGE MANAGEMENT kk bl tb tk kt tat kaka kaka aaa aaa aaa aaa taa tease taaesaesaessesaesasseesoesoesoasoesonsonsoesoeosnosnoaunn 89 5 17 PREVIEW FILE MENU tt tt kb tk kt kt aw aw aaa aaa aaa aaa aaa taa tata teaeesesseaaeaassassessoesoeseasoesonsonsoesoeosnosnoaunn 90 5 18 PREVIEW EXPORT FORMAT lbt bb bb kt kt ke kaka kata aaa aaa aaa aaa e aaesaesaesaesoesoesoeseesoasonsoesoeoseosooounn 90 5 19 E MAIL FORMAT T et t it tt a e at ap te e e e a nn an n e ld ap eka a ee pan n ta n a nnn 91 5 20 PREVIEW VIEW MENU kk kt kb tk katkat kw kw aaa kaa aaa aaa aaa aaa tate asa essesaesaesaesaesoeseesoeseesoasoessesoeosnosooaunn 91 5 21 CUSTOMIZE TOOLBARS ie ane a ian outa ati n aka an na an kak n a ak ka n ka kak an a na a AN n a ak ka m kaka a 92 5 22 NEW 1 OO API E ata tal tak n tk tt tan ala at E n ka e aj a ip 92 5 23 NEW CUSTOMIZATION etwi e bin tan n e kan e ane e a eko n a ka a anko n ak ed asi 93 5 24 CUSTOMIZE COMMANDS eki b lbt kek t kw kaka kaka aa aaa aaa saaa aaa a
30. eee ee ee eee etre eee eee eee sree tena Last date selection images From Interval date selection From 06 07 2010 06707 2010 Manual selection From 04 04 2010 04 04 2010 Enable Path D WR 10X 4rchive D WR 10X Evento_2010_04 Map settings Iv Radar Image Iv Nations Ivi Regions v Provinces _ Municipalities Ivi Cities L Cities amp Town L Rivers a GIF Products filter Without clutter i With clutter v Elevazione 10 0050 Work mode Automatic selection Show the last PUPP COPPA PCE E Eee eee eee ee ee eee ease ees Last date selection images From 27 02 2010 Interval date selection From 06 07 2010 06 07 2010 Manual selection From 0404 2010 04 04 2010 Enable Path D WR 1LOX Archive D IWR 10X Evento 2010 04 Map settings L Default Mark Iv Radar Image Iv Nations Iv Regions Iv Provinces _ Municipalities Iv Cities L Cities amp Town _ Rivers 8 GIF Products filter Without clutter With clutter Range 72 Km 0050 Page 87 of 118 EP DES van User Manual Server 5 5 Menu Bar File view Settings tility Tools The menu bar includes the following entries e File e View e Settings e Utility e Tools At fir
31. for the declutter algorithm and to enable specific operating modes useful to the installer This will not be described in this manual while only the related Log file will be shown see 3 3 4 In the RS232 radar command configuration box parameters related to the radar serial connection are set COM Port selects the COM port necessary to the connection Baudrate selects the connection speed values from 300 to 128000 baud Parity selects the parity control tyoe None Odd Even Data bit selects the data bit number Stop bit selects the stop bit number It is practically possible to configure during the installation only the number of the COM port used for the commands serial channel of the radar All other parameters because of implementation needs must have the following values Baudrate 9600 Parity Odd Data bit 8 Stop bit 1 3 3 1 SignalProcessing log The log file called SignalProcessing is a file which is generated if enabled by the Save Advanced Analysis log on file flag section 3 3 Each month a new file named according to the following logic is generated SignalProcessing YEAR MONTH and it is stored in the C Programs WR 10X Bin LogFiles path A typical example of this file is shown in the following figure ELDES Document code Page 56 of 118 Proprietary Information OM 11242 10 01 EP DES WR 10X User Manual Server Da PEEP PEEP De Di PEPE EPP EE PE 01 Dec 2011 23 48 18 ddd de te ee eee NOIS
32. hardware key in the USB port Insert the CD including the application in the proper driver lf the auto run is enabled the Fig 2 2 will appears Otherwise it s necessary to manually start the installation by launching the InstallManager exe file on the WR 10X_Ver4 0 0 Olnstall folder see Fig 2 1 Pe InstallManager 1 WR10X_Ver3_0_0 Install InstallManager Organizza Indudinellaraccolta Condividicon Masterizza Nuova cartella Ev m 7 Nome Ultima modifica S DevExpress Data v 1 dl 02 07 2008 17 50 Estensione dell apoli 550 KB DevExpress Utils v 1 dil O2 07 2008 17 50 Estensione dell appli 3 705 KB S DevExpress XtraEditors v8 Lal 02 07 2008 17 50 Estensione dell apoli 1 453 KB if InstallManager exe 29 11 2011 10 27 Applicazione 48 KB _ InstMng cfg 10 02 2012 15 21 File CFG 1KB intranet full trust add cmd 08 07 2008 12 11 Script di comandi Wi 1KB Fig 2 1 InstallManager folder ELDES Document code OM 11242 10 01 Proprietary Information Page 7 of 118 EP DES anan User Manual Server ie Install Manager loj x E WR 10X License Server Service Fig 2 2 Install Manager On the Install Manager window select the WR 10X and the License Server Service check boxes the License Server Service is required only for the first installation Click Install to start the installation the WR 10X installation starts first ELDES Document code Page 8 of 118 Proprietary Informatio
33. have also available a series of columns which allow to monitor the status of the scheduled tasks related to the scan On each column it is possible to carry out operations such as layout resizing position changes enable its display or not this is possible by holding the left mouse button on the column and dragging it or by clicking with the right mouse button choosing the related entry By clicking on the name a window called Radar Setting activates on the right section Clicking on the Modify button it is possible to have access to this window see Fig 3 3 On this window it s possible to set 2 parameters which are very important for the system architecture the Radar Network and the Radar ID The Radar Network specifies the NETWORK which includes the radar At Client level it is possible to find several networks supervising different geographical regions as South Area North Area etc each of which is composed of several radars The Radar Network specifies the network in which the radar is included in the example of Fig 3 3 the network is called A ELDES Document code OM 11242 10 01 Proprietary Information Page 23 of 118 EP DES van User Manual Server This letter will be included as initial part of the name identifying each file generated during the scan operations and through this letter the DataAcq Client version will be able to identify the network related to each file it will manage The Radar ID parameter follows
34. is greater or equal to the LevelRejectThr value This kind of filtering is suitable for suppression of radar to radar interfering signals if e the interfering signal PRF value is far from WR 10X PRF value ELDES Document code Page 114 of 118 Proprietary Information OM 11242 10 01 amann EDES User Manual Server e the interfering signal PRF value is very quickly variable between two PRF near values An example related to this filtering application is reported in Fig 8 3 and the meaning of lagi lagi and lag2 SpaceFilter is reported in Fig 8 4 Fig 8 3 Radar to radar noise suppression It is recommended to set the LevelRejectThr value to 30 levels and decrease it until interfering signals are not present in any case it is advisable to choose a LevelRejectThr value greater or equal to 20 levels in order to avoid weather signal suppression The Lagi Lag1 and Lag2 SpaceFilter meaning is explained in Fig 8 4 Document code ELDES OM 11242 10 01 Proprietary Information Page 115 of 118 EP DES van User Manual Server IntReject 2 lag 1 Example of PPI sector not in scale Example of PPI sector not in scale Fig 8 4 Lag1 Lag1 and Lag2 SpaceFilter meaning IntReject 3 one dimensional SpaceFilter applied on RAW data In this case only the LevelRejectThr parameter is used in order to define the threshold in levels under which the filtering process will not apply The f
35. levels In the Colortable composition the following conditions must be observed Hold the black R 0 G 0 B 0 on the first line Do not use the reserved combination R 242 G 0 B 0 in the scale definition The lines total number must be equal to multiple of 8 1 9 17 25 33 ELDES Document code OM 11242 10 01 Proprietary Information Page 73 of 118 EP DES anan User Manual Server 4 Folders structure A short description of the structure related to folders included in the software is given below The syntax with which files are named and their function will also be described ELDES application in server version creates a compressed cab archive for each active scan execution The file is temporarily put in a proper FTP space external to the server or if an external FTP area is not available the file is written on the server machine in C inetpub ftproot WR10X or in a shared folder The cab file follows the nomenclature described below rnn yyyymmddhhmm cab where rnn is an identifier univocal for the radar inside a possible network In particular r is the letter within the A Z range identifying the radar network while nn is a number within the 00 99 range identifying the specific radar inside the network yyyymmddhhmm shows the reference date in UTC format of the cab file The format used in this case has the following order year month day hour minute The cab file includes four types of fil
36. named ToSendFile in which cab files compressed are stored when it has not been possible to establish a connection with the FTP site Once the connection has been restored all files stored in this folder are downloaded in the FTP space and ToSendFile folder is emptied As regards the archives management the system is structured as follows according to the settings specified for the archiving function the operation is automatically activated once a day starting from the fixed hour up to the complete archiving of all products files older than N days from the current date The product files are archived in the proper C Programs WR 10X Archive folder inside a structure of sub folders with a three level hierarchy year month and day 2 wr 10x 3 2 archive 2 PPI 2 2008 2 02 2 01 2 02 Fig 4 2 Folders structure ELDES Document code OM 11242 10 01 Proprietary Information Page 75 of 118 EP DES van User Manual Server If for example the test schedules requests are launched for 3 days from February the 1 2008 and with N 1 the folders structure included in C Programs WR 10X Archive PPI at 00 00 of February the 3 will appear as shown in the figure According to the options which have been chosen the archiving system will take files from the DataFile directory the related sub folders and it will archive them in the Archive folder according to the above mentioned logic Files which can be archived are g
37. press Finish to exit the License server service installation License Server InstallShield Wizard InstallShield Wizard Complete The InstallShield Wizard has successtully installed License Server Click Finish to exit the wizard lt Back Eancel Fig 2 12 License Server InstallShield Wizard End The Fig 2 13 shows that the License Server service installation is completed InstallManager a a Installation procedure completed k A Fig 2 13 License Server InstallShield Wizard Completed Document code ELDES OM 11242 10 01 Proprietary Information Page 17 of 118 EP DES anan User Manual Server After the installation check the status License Server service by verifying the relative icon on the Windows applications bar see Fig 2 14 a GP EGk so Er start Fig 2 14 Windows applications bar The License Server Service icons are described in Tab 2 1 Tab 2 1 The License Server Service icons License Server Service available License Server Service unavailable In case the service is not available try to manually restart the service as follows Insert the hardware key in the PC USB port Double click on the service icon 3 in order to open the License Server Control Center window see Fig 2 15 H License Server Control Center D x Fig 2 15 License Server Control Center Click on the Close button OF the Fig 2 16 appears ELDES Document code Page
38. printing view Background Page Layout Facing Toolbar wo Continuous Status Bar Customize wa Fig 5 20 Preview View menu Putting a flag on Toolbar and Status Bar entries these will allow to display respectively the toolbar at the top of the window below menus and the status bar at the bottom of the window below the image ELDES Document code OM 11242 10 01 Proprietary Information Page 91 of 118 EP DES anan User Manual Server Customize Selecting Customize the window that appears is the same window which is possible to display clicking with the right mouse button on DataView menu bar This allows to customize the Preview window toolbar The Customization window is divided into three sub folders Toolbars Commands and Options Toolbars allows to customize the toolbar Toolbar and Status Bar options are equal to the same options in the View entry Main Menu option is always enabled Customization Toolbars _ Commands Options Toolbars Toolbar Status Bar ls Main Menu Fig 5 21 Customize Toolbars Clicking on the New button a window related to the creation of a new customization whose name can be chosen appears Mew Toolbar Toolbar Warne Cancel Fig 5 22 New Toolbar Once the customization window has been created this will appear together with the above described entries ELDES Document code Page 92 of 118 Proprietary Information OM 11242 10 01
39. ran 100 5 39 MAP CREATOR GRAYSCALE MODE kk bek k tt kt kt aaa aa kaka aaa aaa aaa aaa aa eeesaesaesesoesoeseooesoesooseooesononnn 101 5 40 MARK CREATOR INTERFACE ccceccecceccecceccecceccuecuecaecaeeaecaeeaeeaueaeeaeecueceesuesuesuesuesaeeneeaees 102 ELDES Document code OM 11242 10 01 Proprietary Information Page 5 of 118 WR 10X User Manual Server FIG 5 41 MARK CREATOR PREVIEW ccccecceccecceccecceccucceecuecaeeaecaeeaecaeeaeeaeeceesueseecuesuesueeueeeneaneaeeass 102 FIG 5 42 LAYER CREATOR PREVIEW cccceccecceccecceccecceccuecuecaeeaecaecaeeaeeaueaeecuecueseesuesuesueseeeueeaneneeass 103 FIG 5 43 LAYER CREATOR PREVIEW cccecceccecceccecceccuecuececaeeaecaecaeeaeeaeeaeeceecueseesuesuesuesureueeaneaeeaes 105 FIG 5 44 LAYER CREATOR LAYER NAME SELECTION MASK 0scceccceeceeceeeceseeeeceeaeeceeeaeecueeaeeeeeeneeens 106 FIG 5 45 LAYER CREATOR PREFERENCES WINDOW 2 ccceececcecceceeceeceececeececceceeceecescesaesueeneaes 107 FIG 5 46 ZOOM IMAGE EXAMPLE 1 ececcececeececeececeececeececeececeeaeceeaeceeaeceeaeaesueaeseeaeseeaeceeneaueneaesneaeeaes 109 FIG 5 47 ZOOM IMAGE EXAMPLE 2 bibit bbl bb kt kaka kaa kaa kaa aaa aaa aaa aaa tea taaeaaesaesaesaesoesoesoasoesoesoessesounsnosnnonnn 110 FIG 6 1 MODIFIED COLOR TABLE titit kin a at a ai ot n et st n aaa n e e n kt kte ab e a 110 FIG 7 1 CLUTTER MAP IMAGE EXAMPLE bbl k kl kt kt kt kaa kaa kaa kaa taa aaa aaa
40. the observed cell from the radar expressed in Km P is the average power received by the radar antenna coming from the involved cell located at a distance r from the radar and expressed in dBm These parameters can be obtained by the matrix of integrated data in log power dBm resulting from the processing previous to the radar constant calculation Typically the Z parameter is expressed in mm m in the above mentioned relation it is necessary to apply a further correction factor for the conversion of the units of measure In order to be better represented Z is expressed in dBZ 10xLog Z so isolating r and P variables related to the single cell in the radar equation a constant C is introduced depending on the system characteristics and reflection properties of water drops dBZ 10 x log Z C P dBm 20 x log r Km ELDES Document code Page 44 of 118 Proprietary Information OM 11242 10 01 vann EDES User Manual Server The constant C expressed in dB is obtained as 10xLog of the constant part related to the radar equation expressed in linear form In order to consider losses due to the radome effect not perfectly transparent and to the run on the sliding guide insertion loss of some microwave components a further term L is included in the C radar constant L element depending on the radome attenuation can be changed through the interface using the entry Radome attenuation A further loss factor must
41. the same logic except for the fact that it will identify each single radar inside the same network specified by the Radar Network parameter lt is clear that these parameters can be set only by the DataAcq Servers the DataAca Client will only use them to manage files and generate products W DataAcg Data acquisition and signal processing manager 1 KAN po wa Signal process fa Li JA WIGS Radar Scan list Sched Next Last R Status Radar setting DefautRadar racer setting L Scan 0 Not sc Never Newer Radar network Radar ID modify i f Restore Save and Exit Save Exit Load profile Start selected scan Fig 3 3 Radar setting Once Radar Network and Radar ID parameters have been set activating the drop down menu available under the symbol it is possible to rename the radar see Fig 3 4 add a new scan Add scan or remove that currently selected Delete scan see Fig 3 5 Radar Scan list Sched S Default Radar Fig 3 4 Radar name and scan ELDES Document code Page 24 of 118 Proprietary Information OM 11242 10 01 WR 10X User Manual Server a se Signal process fine gt Scar Signal process WRIO WR10 WRI0 gt Radar Scan list Sched Next Last R i Peg o Befauk Radar Radar Scan list Sched Next Last A i Scan 0 er E Default Radar Sean 0 ee ae Fig 3 5 Add remove scan
42. 1 11201 1256 B 0360 0150 0010 0010 U z if we also consider the header presence on each ray the integrated data matrix for the PPI scan has a size of 360X263 The z binary file related to PPI integrated data is saved in a ushort format Unsigned Integer 16 bits 3 2 3 Structure of RHI integrated data In RHI scan the integration elementary unit is the resolution cell on the vertical plane determined by the antenna beam selected from DataAcq interface and by the range resolution selected from DataAcq interface As regards this radar system the beam antenna width on the vertical plane is equal to 3 but it is also possible to apply an oversampling in azimuth by selecting from DataAcq interface a beam width lower than the nominal lf we consider the restricted speed of the elevation scan the number of samples available for the integration inside each selected antenna elevation beam width resolution cell is very high The elevation resolution for the RHI scan is selectable from DataAcq interface For this kind of scan angles the scan beginning and end can be configured by the interface so the cells number on the vertical plane depends on these settings N abs Elout _ Bl EL sikina There are four range For each range can be selected different range resolution according to the Tab 3 1 The file name contains some of the information necessary to determine the size and number of cells contained in the integrated file z
43. 1242 10 01 Proprietary Information Page 33 of 118 EP DES van User Manual Server 3 1 4 Communication The Communication folder includes the fields which must be filled to set the FTP server address to which data have to be sent Communication Communication settings Send data to FTP Server FTF Server name FTP directory name User name Password Phonebook entry Fig 3 11 Communication In order to enable the fields included in the folder it is necessary to put a flag on the option Send data to FTP Server ELDES Document code Page 34 of 118 Proprietary Information OM 11242 10 01 vann EDES User Manual Server FTF Server name F Use RAS connection to send data Phonebook entry Fig 3 12 Enable data transmission In this way it is possible to enter e FTP Server name the server name or IP address e FTP directory name the name of the Server directory e User name e Password lt is possible to put a flag on the Use RAS connection to send data option if the connection to the FTP site has to be established via GSM or GPRS Phonebook entry F Disconnect RAS at the end of transmission Fig 3 13 RAS connection In this case it is necessary to enter in the Phonebook entry field the entry previously configured in the Windows phonebook which calls the GSM or GPRS modem and which is necessary to establish the connection lt is also possible to put a flag on the Disconnect RAS at the end of transmiss
44. 18 Proprietary Information OM 11242 10 01 EP DES WR 10X User Manual Server At the end of the DRAW procedure the IMAGE DIMENSION and IMAGE TYPE controls besides the SAVE button are made available on the interface IMAGE DIMENSION allows to specify the size expressed in pixel of the image to generate square image IMAGE TYPE allows to specify if the image should be generated in Truecolor mode that IS to say with all colors shown in the preview window or in Grayscale mode that is to say in a scale of grays The following figure shows the image version displayed in the preview window generated in Grayscale In this situation it is possible to change again the parameters of the map to generate and display a new preview of the Background Map clicking on the SAVE button Zao Y apr I oF E A Foe ki f a At We i Concha ah kis VAN yo yo es YE f pi m za y a A wy A LA y pa 3 y ed Sot AE Eso m oe aN Tans d AAA ki j asciana N Fa ki N JAN 58223 Fig 5 39 Map Creator Grayscale Mode The EXIT button allows to close the interface at any time provided that the routines related to the preview generation and the map generation in graphical format are not running 5 5 4 2 Mark Creator Mark Creator is an application intended for the creation of marks necessary for the localization in polar coordinates of radar images The following figure shows the application configuration interface ELDES Document code
45. 58 of 118 Fig 3 30 DataAcqTsk Log ELDES Document code Proprietary Information OM 11242 10 01 mann EP DES User Manual Server 3 3 3 SignalProcessingError log The purpose of this log file is to save in a file all ERROR messages coming from the Advanced Analysis module This file is continuously updated This function can be useful in case of system fault to analyze the scan process point in which the problem has occurred or occurs This log is Monthly type i SignalProcessingError201202 txt Bh Youn n ote f A la x Fie Modifica Formato Visualizza 7 T obi e e SSS SSS SESS SPSS a e T e ESS SP PSE SESS bP bbb edd oo a a a a a a A a a a a a A a a n a a A E Error LOG File February TE SEES a e ae SEES SEES SEES bibi a a a a a a a a a a a a a n Da pp a pp ok op ob bb bb PPP PPP baba 15 Feb 2012 09 13 03 i le ERROR AZIMUTH ANOMALIES IN NUMBER lt 15 AND NOT CONSECUTIVE SCAN PROCESSING RECOVERED a a a a a a a a a a a a aa ae a ed 15 Feb 2012 14 13 29 lied oe ce ee ce ce n e e e a ee ERROR AZIMUTH ANOMALIES IN NUMBER lt 15 AND NOT CONSECUTIVE SCAN PROCESSING RECOVERED PEPE SPSS PPPS bbb SSD SDD SS a a a a e a a a 15 Feb 2012 14 13 41 lt tc a ee ERROR CONSECUTIVE AZIMUTH ANOMALIES SCAN PROCESSING RECOVERED Fig 3 31 Signal processing error log 3 3 4 Decision Threshold Log file The Decision Threshold txt is a log file and it is related to the PPI scanning The Decision Thresho
46. 938 180 72 Kim 300 m 93 180 72 Km 450 m Fig 3 10 Clutter filter Settings The Decision Threshold field defines the percentage which usually the clutter takes in the PPI IN CLEAR AIR If the percentage of cells with a StdDev lower than the Low Threshold is higher than the percentage shown in this field the PPI is considered as a PPI of clutter and it is managed accordingly Decision Threshold lf the percentage is lower the PPI will be considered as a weather PPI and it will be managed in a different manner According to the used range 36 or 72 Km the percentage of clutter in the PPI changes so there are 2 threshold values depending on the range which is used Furthermore in the central column it is possible to define an elevation angle above which NO clutter signal is still visible and so above this elevation angle NO declutter algorithms will be applied In order to limit the presence of possible distortion of the weather echo the statistical filtering is applied in a selective way Using the Decision Threshold Low threshold High threshold as initialization parameters some clutter maps are dynamically updated Clutter maps are status maps as they highlight cells in which in clear air there is clutter and they are as much as the elevations set in the schedule The statistical declutter algorithm is only applied on cells for which the clutter map related to the specific elevation has a value equal to 1 ELDES Document code OM 1
47. AMP S HEADER TIMESTAMP ms HEADER INDEX HEADER_SCANTYPE HEADER AZIMUTH HEADER AZIMUTH IN HEADER AZIMUTH OUT HEADER ELEVATION HEADER ELEVATION IN HEADER ELEVATION OUT HEADER PULSEWIDTH HEADER PRF HEADER RANGE HEADER RANGESTEP HEADER ELEVATIONSTEP HEADER ELEVATIONSPEED HEADER NUMPULSES HEADER MEANNUMPULSES HEADER BE HEADER DATAFORMAT where e HEADER TYPE Number of fields contained in the header For RHI integrated data this field value is 23 e HEADER_TIMESTAMP_Y Field year of the timestamp corresponding to the time where you started the acquisition of the specific azimuth cell 4 digit for year e HEADER_TIMESTAMP_MG Field month day of the timestamp corresponding to the time where you started the acquisition of the specific azimuth cell 2 digit for month 2 digit for day e HEADER_TIMESTAMP_HM Field hours minutes of the timestamp corresponding to the time where you started the acquisition of the specific azimuth cell 2 digit for hours 2 digit for minutes e HEADER_TIMESTAMP_S Field seconds of the timestamp corresponding to the time where you started the acquisition of the specific azimuth cell 2 digit for seconds e HEADER_TIMESTAMP_mS Field milliseconds of the timestamp corresponding to the time where you started the acquisition of the specific azimuth cell 3 digit for milliseconds e HEADER_INDEX Sequential index of the row takes integer values from 1 to number of rows e HEADER SCANTYP
48. D cccccceccecceccecceeceececeeceeeaeeaeeaeeaeeceeceeceeeueeuteueeaneaees 13 FIG 2 8 LICENSE SERVER INSTALLSHIELD WIZARD cccccccecceccecceccecceececeeeeecaeeaeeceeceeceeceecueeueeueeaneaees 14 FIG 2 9 LICENSE SERVER INSTALLSHIELD WIZARD PATH cccecceccecceeceeceeeeeceeeaeeceeceecueceeceeeueeaeenseaees 15 FIG 2 10 LICENSE SERVER INSTALLSHIELD WIZARD READY cccceccecceeceeeeeceecceececcueceeceecuecusenseuseaees 16 FIG 2 11 LICENSE SERVER INSTALLSHIELD WIZARD QUESTION 2 cecceeceeeeeceeeeeeceeceeeeeceeeeeeeeeneeneenees 16 FIG 2 12 LICENSE SERVER INSTALLSHIELD WIZARD END c cccceccecceeceeceeeeeceeeceeceeceeceeceecuecuseusensenees 17 FIG 2 13 LICENSE SERVER INSTALLSHIELD WIZARD COMPLETED 0 0ececcecceceeceececceceececcesaeeseneeeeas 17 FIG 2 14 WINDOWS APPLICATIONS BAR bet bk kb tk kt kaa aaa a aaa aaa aaa aaa aaa taa aaa eea sea essesaesaesaeseeseesoasoesoesoesoeoooooooon 18 FIG 2 15 LICENSE SERVER CONTROL CENTER kl bek b bk kk ka kaa a kaa aaa aa aaa aaa aaa aaa eesoeseeseesesoesossesoesoesooseoononnenn 18 FIG 2 16 LICENSE SERVE CLOSING APPLICATION kl kk tett kt kaka aa aaa a aaa aa aaa ea eat easaeoeseseeseseeoeseooesoooeseoonsoooun 19 FIG 2 17 LICSRV EXE FILE ai sion anba ja kb a ik ides datasets kn bl E kikit dp it e bn ie lo A Ren da t 19 FIG 2 18 LICSRVUI STARTING vee ccecesctccctescecccvetesdestepbicdatetatocsseedeedeueiasddaeagdeedatesabadeaeensedeuetaciebsacdecdatazest 19 FIG
49. E Scan type identifier 1 PPI 2 RHI 3 SECTOR only predisposition For RHI integrated data this field value is 2 e HEADER_AZIMUTH Antenna angle azimuth point for the RHI acquisition This field is expressed in decidegrees integer value between 0 and 3600 e HEADER_AZIMUTH_IN Only predisposition for future use in azimuth sector scan type For RHI scan type this field is equal to HEADER_AZIMUTH e HEADER_AZIMUTH_OUT Only predisposition for future use in azimuth sector scan type For RHI scan type this field is equal to HEADER_AZIMUTH ELDES Document code OM 11242 10 01 Proprietary Information Page 53 of 118 EP DES van User Manual Server e HEADER_ELEVATION Elevation position at the end of the specified ray This position is expressed in decidegrees integer value between 0 and 3600 e HEADER ELEVATION IN Angle elevation at the start of the elevation sector acquired This field value is expressed in decidegrees e HEADER ELEVATION OUT Angle elevation at the stop of the elevation sector acquired This field value is expressed in decidegrees e HEADER_PULSEWIDTH Transmitted pulsed width expressed in nanoseconds integer value on 4 digit e HEADER _PRF Transmission pulse repetition frequency expressed in Hz 10 integer value on 4 digit with default value 8000 Hz 10 e HEADER_RANGE Acauisition selected range expressed in hundreds of meters integer value on 4 digit e HEADER_RANGESTEP Acquisition selecte
50. E PARAMETERS MEASUREMENT 2011 11 21 10 38 01 NOISE MEAN LEVEL 26 7852 level 2011 11 21 10 38 01 NOISE MAX LEVEL 45 0000 level 2011 11 21 10 38 01 NOISE MIN LEVEL 10 0000 level 2011 11 21 10 38 01 NOISE PEAK PEAK LEVEL SIGNAL 34 5000 level 2011 11 21 10 38 01 NOISE STANDARD DEVIATION LEVEL 4 6440 leve1 2011 11 21 10 38 01 NOISE RMS LEVEL 31 8782 level T Do PEPE PEEP PEPE PEEP EP 01 Dec 2011 23 48 36 2011 12 01 23 48 36 RANGE 21 60 Km 2011 12 01 23 48 36 ELEVATION 1 00 2011 12 01 23 48 36 CELLS DIVISION 2011 12 01 23 48 36 PPI TYPE CLUTTER MAP PPI 2011 12 01 23 48 36 NUMBER OF EMPTY CELLS 554 cells 2011 12 01 23 48 36 NUMBER OF GROUND CLUTTER CELLS 85571 cells 2011 12 01 23 48 36 NUMBER OF MIXED SIGNAL CELLS 229 cells 2011 12 01 23 48 36 NUMBER OF WEATHER SIGNAL CELLS 46 cells 2011 12 01 23 48 36 THEORIC DECISION THRESHOLD 99 68 per 2011 12 01 23 48 36 THEORIC LOW THRESHOLD 5 07 lew 2011 12 01 23 48 36 MEAN THEORIC DECISION THRESHOLD 99 68 per 2011 12 01 23 48 36 MEAN THEORIC LOW THRESHOLD 5 07 lev 2011 12 01 12 52 12 WARNING V Rot Required 20 0 t sec 2011 12 01 12 52 12 v Rot Measured 19 9 t sec 2011 12 01 12 52 12 v Rot Error 0 100 sec 2011 12 01 23 48 37 ELAPSED TIME 17 86 sec Fig 3 29 Signal processing log The purpose of this file is to provide a log of the software module carrying out the signal processing in order to value possible corrections to make to the d
51. MUNIGATIO Nini notr ii ta ek li il v n ko ka a n ka a e a e n ak ak n RD L 34 FIG 3 12 ENABLE DATA TRANSMISSION sait exc decweriacudtseusseeues sosyarsausdusteriesrdeeeusaammmnieeroansdsersarens 35 FIG S FA 5 GON NEG TION s ea tij at sb tibebe evit va kant tett a at a at da ke aka e a kf ka e e ba n al L e 35 el ee ag SONE DIE R eee ot ati ta on est beat en aye ko pete ee ey ki el a ei e e e ee Pu re so to ae n 36 FIG 3 15 TASK EXECUTION WINDOW 0tak ob lik a ok a l kal da e ak a e ee n ak pp ions 37 FIG 3 1G ENTER PASSWORD e eee a EE ala a a A E EEEE 37 aE DEIN e R E S 38 FIG 3 18 SCHEDULING ADDITION cccccccecceccecceeeeeceecceeceecueceeceecuecuececuecaesaeeaesaeeaeeaeeseeseeseesueseesaesaeeaees 38 FIG 3 19 TASK SCHEDULING 2 bbl bbl kt kt kaa kaa kaa kaa kaa kaa aa aa aaa aaa aaa aaa tat easeataeseesosesessessesseosoasonsoesonsoesonsonosuoo 38 FIG 3 20 ADVANCED SCHEDULING OPTIONS lbt bk tb tat kaa kaka aaa aaa aaa taa aaa aaa aeaeaaesaesaesaesaesoesoesoesoasoesoeooeoonnon 39 FIG 3 21 SCHEDULED TASK SETTINGS ccccecceccecceeceecceeceecueceecueceececuecuecesaeeaeeaesaueseeseeceeceesueseeeaesaeeaees 39 FIG 3 22 SCHEDULING REMOVAL ccccecceccecceeceeceeceeeceeaeecueceecueceecuececuecaesaesaesaeeaeeaeeaueseesuesueseesaesateaees 40 FIG 3 23 PRODUCTS ki kin kai ate tines sr ati ot m an nage e n t n a n aida dd ek bn Eb e a e n pa Ra 41 FIG 3 24 ADVANCED WORK MODE kek bek t kt kaa kaa kaa kaa aa aa aaa aaa aaa aaa aaa a aa
52. R PULSEWIDTH HEADER PRF HEADER RANGE HEADER RANGESTEP HEADER AZIMUTHSTEP HEADER_AZIMUTHSPEED HEADER NUMPULSES HEADER MEANNUMPULSES HEADER_DATAFORMAT where e HEADER TYPE Number of fields contained in the header For PPI integrated data this field value is 23 e HEADER_TIMESTAMP_Y Field year of the timestamp corresponding to the time where you started the acquisition of the specific azimuth cell 4 digit for year e HEADER_TIMESTAMP_MG Field month day of the timestamp corresponding to the time where you started the acquisition of the specific azimuth cell 2 digit for month 2 digit for day e HEADER_TIMESTAMP_HM Field hours minutes of the timestamp corresponding to the time where you started the acquisition of the specific azimuth cell 2 digit for hours 2 digit for minutes e HEADER TIMESTAMP S Field seconds of the timestamp corresponding to the time where you started the acquisition of the specific azimuth cell 2 digit for seconds e HEADER_TIMESTAMP_mS Field milliseconds of the timestamp corresponding to the time where you started the acquisition of the specific azimuth cell 3 digit for milliseconds e HEADER_INDEX Sequential index of the row takes integer values from 1 to number of rows e HEADER_SCANTYPE Scan type identifier 1 PPI 2 RHI 3 SECTOR only predisposition For PPI integrated data this field value is 1 ELDES Document code Page 50 of 118 Proprietary Information OM 11242
53. SION allows to set sizes expressed in pixels of the layers images to save in graphic format Possible choices are in this case 480x480 640x640 820x820 1024x1024 image Type image Dimension Truecolor w 1024 Truecolor Layers can be saved in GIF TIFF PNG BMP graphic formats clicking on the SET button The following figure shows the definition window of the path and the layer name Document code ELDES OM 11242 10 01 Proprietary Information Page 105 of 118 WR 10X User Manual Server LayerMapCreator VIEWER UTILITY Layer Map Name BMP files BMP w Annulla DEM Data Cities Nations Bound Rivers image Type image Dimension Regions Bound Roads Truecolor k 1024 O Provinces Bound Rails O Municip Bound O Ali Layers Georef control Geodata file DIR D WR 10 Bin CARTOGRAPHY FIND Fig 5 44 Layer Creator Layer name selection mask Clicking again on the SAVE button a graphic file will be generated for each selected layer and the name of the single layer is created attaching a layer type description to the name specified by the user Settings shown in the previous figure generate the following files Gl Radari_Cities bmp Gal Radari DEM_dted bmp Gl Radari_Nations bmp ElRadart Regions bmp lal Radari Rivers bmp In the application menu bar two choices are available VIEWER and UTILITY VIEWER enables the preview w
54. a OK Aru In particular it is possible to select a color from the preset palette applying it clicking on the OK button or it is possible to have access to an advanced mode clicking on the DEFINE CUSTOMIZED COLORS button In this case it is possible to select with the mouse a color from the palette on the right side of the window add it to the customized colors clicking on the ADD TO CUSTOMIZED COLORS button select it among the customized colors and finally apply it clicking on the OK button The GENERAL section allows to select from the proper control the referenced nation for which the boundaries BND file will define the dataset of the neighboring nations possibly involved in case of generation of layers centered on geographical position close to the referenced nation boundaries GENERAL Nation Database A Nations Boundaries A B SET Selection SVIZZERA File Selection WR TOABINCARTOGRAPH V boundanes BND ELDES Document code Page 108 of 118 Proprietary Information OM 11242 10 01 amann EP DES User Manual Server 5 5 5 Tool Selecting Tool from the menu bar it is only possible to choose Zoom Expanding it it will be possible to have access to other entries such as Enable Zoom or the shortcut CTRL Z which enables the Zoom function of the displayed image Area to zoom is selected with a rectangle on the image and can be done in a recursive way Zoom In or the shortcut Zoom Out or the short
55. aaa EEEE R txt where XXX Network and radar number identifier AAAAMMGGHHMM Acquisition data start time of the radar scheduler B Not used RRRR Range expressed in hundreds of meters rrrr Range resolution range expressed in meters aaaa Azimuth resolution expressed in decidegrees EEEE Elevation expressed in decidegrees R Not used 3 2 2 Structure of PPI integrated data Processing algorithms applied to RAW data make integrated data available for the subsequent processing possibly clutter free Integrated data are generated in binary format for the two elementary moments of PPI reflectivity and RHI reflectivity Integrated data are identified by the z extension and are used as input parameters by the product generators algorithms In PPI scan the integration elementary unit is the resolution cell on the azimuth plan determined by the antenna beam width selected from DataAcq interface and by the range resolution selected from DataAcq interface As regards this radar system the azimuth antenna beam width is equal to 3 so the whole scan on 360 will include 120 azimuth cells but it is also possible to apply an oversampling in azimuth by selecting from DataAcg interface a beam width lower than the nominal There are four range For each range can be selected different range resolution according to the Tab 3 1 The file name contains all the information necessary to determine the size and number of cells
56. aaa aaa eaassaesaesaesaesoesoesoesoasoessesoesseosooounn 111 FIG 8 1 SPIKE NOISE EXAMPLE an a an kn ta n a e a etat a ke mt a e at n ott kosa kw mn e b k ali 113 FIG 8 2 DIMFILTER PARAMETER MEANING IN CASE OF MEDIANFILTER 22 0ecceeececceceeecceceeeeeeeeneeens 114 FIG 8 3 RADAR TO RADAR NOISE SUPPRESSION kb bbl kte kt kte kaa a ea aaa aaa a aaa aaa aaa aaa aaesaeseesoesoesoesoesoesoeoseoaooonnn 115 FIG 8 4 LAG1 LAG1 AND LAG2 SPACEFILTER MEANING 2 0 ceeceeceeeeecceececceececceeceecuccuccuecereuseaeeaseaes 116 List of Tables TAB 2 1 THE LICENSE SERVER SERVICE ICONS kb bb tt kt kaka aaa kaa aaa aa aaa aaa saaa aeeataesaeeeoesoeseesesoesoeseosoeoonsnoen 18 TAB 2 2 SOFTWARE APPLICATION ICONS bib bl bbl kt kaka taa kaa kaa aaa aaa aaa aaa aaa eaeeaaeseesaesaesoesoesoesoesoesoesoesoeosnoaunen 21 TAB 3 1 RANGE RANGE STEP ASSOCIATION ka kb kb kt kaka kaa kaa aaa aaa aaa aaa aaa aaa saasaesaeseeseesoesoesoesoesoesoessooounon 26 Page 6 of 118 ELDES Document code Proprietary Information OM 11242 10 01 vann EDES User Manual Server 1 Introduction This manual is referred to Ver 4 0 0 SRO5 2 Software package installation 2 1 Introduction In order to correctly install the software package it is necessary to have previously installed a Windows 2000 operating system or higher Windows version The following chapter describes step by step the installation procedure 2 2 Installation procedure Insert the
57. acquired date for the specific pulse year month day aaaammdd format The second column show the really acquired timestamp for the specific pulse hours minutes seconds milliseconds hhmmssMMM format The third column shows a simple progressive number necessary to mark the start and the end of cells in azimuth The fourth column shows the azimuth value of the involved pulse The value is expressed in encoder steps where 2047 is the maximum value corresponding to the round angle Each full scan will include the point in which the azimuth meter crosses 0 shown in the example figure This point represents the so called north mark that is the referenced point from which the processing algorithm begins the reorganization of data matrix In order to determine the Start and the End of each azimuth cell a simple proportion is used 2047 360 x AZ resolution For example if the selected azimuth resolution is 3 the value expressed in encoder steps is obtained for each cell of 3 that is 17 0 steps The fifth column shows the elevation value of the involved pulse expressed in number of stepper motor on the elevation axis The antenna position of the elevation axis expressed in degrees is obtained by applying the following relationship ELaeg EL stepper motor A 1 8 64 Columns from the 6 to the last will include AD converter values for all the radar cells The number of cells on each row range bin depends on the setting of the rang
58. addition change The necessary information list is the following e Layer Name indicates the name of the layer which will be displayed in the list This must be univocal inside the product e Transparence indicates the transparence color which has to be linked to layer images It is possible to manually choose it writing the RGB color separating values through a semicolon or choosing it among one of the available colors of the drop down menu which will be displayed clicking on the arrow It is also possible to click on the button with the symbol of a phial 2 in this way a window will appear see Fig 5 12 showing the image related to the Path previously selected Moving the cursor on the image the RGB color related to the pointed pixel will be specified Clicking once with the left mouse button the window will close and the color chosen will be specified in the Transparence field If it is not intended to apply any transparence it is sufficient to leave the field empty e Layer paths in this table it is possible to specify the path in which the specific image for the selected range has to be placed According to the range modification in the Products filter section the image related to this range will be displayed To create the link it is necessary to click on the button in the Path column and the files search screen will appear with a filter set in order to detect only those files having compatible extensions to be managed in the system
59. aesaeoaseeseeoesaesoesessesosseosesoesonsnoonnnnennn 93 5 25 CUSTOMIZE OPTIONS eee tete an be or ci e ab nat mt ee iasa 94 5 26 BAN CE CON fete san aa etan tale Re a e e n a a a a en EEEE 94 5 27 ICONS DESCRIPTION s vi awa avi et ta a kod w tit ik t a ak fk at ak kk a e kaa kak afe a e a ak ak ak 94 5 28 MENU ANIMATIONS ket t bk kk tk kaka aa aa kaa aaa aaa aaa aaa aaa aaa seat a aeaeaeessesaesaesaesaesoesoesoaseesonsoesoesonssnosooounn 94 5 29 BACKGROUND 3 ed etwi twit at ia it a kl edit a a a aa n kk a e n kk ka m a n a a a e 95 5 30 BACKGROUND TEXT au isit as au kan t da n a a n a ka a RE A 95 5 31 BACKGROUND IMAGE kk bt tt kb tk kt aw aa aw kaka aaa aaa aaa aaa aaa aaa tease esassaesaesaesaesoesoesoasoesoasoesoesoessnosooaunn 96 5 32 TOOLBAR CUSTOMIZATION kk tl kt kt kt kaka ka kaa kaa kaa kaa aaa aaa aaa aaa aaa eaaesaesassaesoesoesoeseesoasoesoesoesoeosooounn 96 5 33 TOOLBAR ICONS aoiibii aa isi sena tr tdt ta kitte a aa n kn de n pa l kip ky e ba e e vi ke n e li kad ai ei e 97 STS E ai A A AN A eee gee dete as Sees cepa ten tn ee ee 97 5 35 RADAR SIE SET NNO iii wat ta ta kipa aa ai sa denier a va pa a ab ip a e seatdein dian san e ik tk 98 5 36 PRODUCT VIEW SETTINGS ivietwonawd twa kitan rat n ab a a a a ke e ye is ce kt kt s pak ik ka 98 5 37 MAP CREATOR INTERE AGE cece kitan bras on a a ka e ka e pe is kk a n d ka 99 5 38 MAP CREATOR PREVIEW au driiwdwal isit ok as a ott av da ki a kk a a ka a ek aj ks aaa ka ka eka e a ke
60. ale dBZ Reflectivity is calculated from the average power received by the antenna according to the following relation Document code ELDES OM 11242 10 01 Proprietary Information Page 43 of 118 EP DES anan User Manual Server 1024 x In 2 A r xP Z a x a a x A CXT PxtxG x x KI c 2 9979x10 is the speed of light in a vacuum expressed in m s K 0 93 is the water scattering coefficient These two parameters are fixed and do not depend on the specific installation other parameters are 4 is the wavelength of the transmitted carrier expressed in cm t 1 Transmitted Frequency is the frequency of the transmitted carrier expressed in MHz T Pulse Time is the transmitted pulse time expressed in us G Antenna Gain is the antenna gain measured twice once during the transmission and once during the reception expressed in dB Q Azimuth Beamwidth is the antenna lobe width at 3dB on azimuth axis horizontal axis expressed in Dp Elevation Beamwidth is the antenna lobe width at 3db on elevation axis vertical axis expressed in P Transmitted Power is the peak power radiated by the radar expressed in Kw Note These parameters depend on the specific installation so they must be configured according to experimental data obtained by laboratory measurements and possibly updated on site according to the periodic maintenance inspections to the instrument r is the distance of
61. alue If we remove from the calculation all empty cells or those having a reflectivity lower than a threshold value it follows that the clutter effect in in the PPI rapidly decreases with the arrival of cells having StdDev due to weather signal SO it is easy to recognize the presence of rain inside the PPI and differently manage cells according to the fact that it is a PPI only including clutter or a PPI including weather signal In case of a PPI only including clutter it will be sufficient to remove the cells which contain it in case of a PPI including weather signal the cells will be filtered with a recovery mask in order to display only the weather signal cleared of the clutter ELDES Document code OM 11242 10 01 Proprietary Information Page 31 of 118 EP DES anan User Manual Server So the necessary parameters to realize this kind of filter are basically three e The StdDev value only related to the clutter typical of the installation site e The percentage of incidence of the clutter in the PPI in clear air typical of the installation site e The StdDev value typical of the weather signal As regards the last parameter it is possible to refer to typical values while it is not possible to do the same with the first two parameters The clutter standard deviation highly depends on the installation site Ex Mountain areas wooded hills urban environments etc The same can be said for the percentage of incidence in the PPI
62. at the lat radar site entry see para 4 5 3 ELDES Document code Proprietary Information OM 11242 10 01 vann EDES User Manual Server Trigonometric functions accept angles expressed in degrees Macros including square brackets need an argument to put in them The argument can be a number or a function For example the following syntax SQRT SIN 45 AZIMUTH OFFSET Where AZIMUTH 30 and OFFSET 0 4 Km return the value y sin 45 30 0 4 5 57 Km To explain the syntax to be used for the tooltip composition the value included in the default field together with the PPI product will be examined as follows IDISTANCE DISTANCE SIN VARIABLE OFFSET AZIMUTHI 5 VARIABLE Aeee IMGINFO dBz Text highlighted in BB represents an arbitrary text intended to exhaustively describe the subsequent quantity for the tooltip syntax this is an optional field Text highlighted in YELLOW represents an arbitrary description identifying the unit of measure of the quantity that comes first for the tooltip syntax this is an optional field All that is included between the symbol is considered by the system as a formula which can be composed of MACROS numbers and mathematical operators Each expressed quantity must be separated by a semicolon The graphic representation resulting from this displayed as tooltip of the product selected in the DataView application is the following Image detail
63. be introduced to consider the attenuation due to atmospheric gases Defining with Leas the two way attenuation expressed in dB Km the above mentioned relation changes as follows dBZ 10 x log Z C B dBm 20 x log r Km Leas X r Km The value of the Leas parameter is considered in the calculation of the reflectivity matrix but cannot be changed through the interface Finally it is important to add that data actually available at the software processing input is the matrix of the voltage levels at the LOG amplifier output encoded on 8 bits 256 levels The levels A D gt P dBm association is defined by the following parameters Receiver slope and MDS which express respectively the slope and the offset of the radar receiver characteristic The Reflectivity constant field allows to select Rain if it is necessary to represent reflectivity of a rain field or Snow if it is necessary to represent reflectivity in a snow field In the first case the scattering coefficient used in the radar equation is that related to the water case K 0 93 while in the second case the scattering coefficient is that related to the snow case K 4 15 By means of the Short Medium Long radio buttons it is possible to choose the kind of pulse to transmit The PRF Hz Pulse time us and Matched Filter Loss dB fields are automatically filled and once chosen the pulse kind the related Pulse time and Matched Filter Loss propose
64. c type of product ex PPI This file allows to specify a map of 225 colors max each of which is defined by a RGB level The following figure shows an example of a possible color table which can be displayed by any kind of text editor oom 29 0 ood ood ood out 20 165 255 255 O02 15 137 ala 231 003 10 110 17O 225 OO 4 5 Ga 127 215 005 0 0 55 55 201 006 5 0 a 42 l z DAT 10 0 D m 175 008 15 0 61 2359 a4 ooo 14 0 45 214 TO o10 21 0 30 1559 47 O11 242 0 15 164 as iz 27 0 Oo 140 Oo O15 30 0 255 255 Oo O14 32 0 255 2355 Oo O15 34 0 255 al D O16 36 0 255 196 Oo o17 350 0 255 177 Oo Oois 470 0 255 157 Oo 01S 42 0 255 135 D O20 44 0 255 119 Oo O21 46 0 255 51 FA O22 45 0 237 By as O25 50 0 219 54 za Oz 4i 58 0 201 40 17 O25 54 0 163 ay 11 O26 56 0 165 13 5 O27 55 0 147 Oo Oo 026 60 0 255 45 255 O25 62 0 202 36 226 O30 64 0 210 24 195 Osi 66 0 1S7 12 17O O32 60 0 165 0 142 Fig 3 44 Example of color map The first column is a sequential number the second column specifies the limits of the size to be displayed reflectivity limits dBZ for the PPI product in which the color specified in the subsequent columns is used Columns 3 4 and 5 show respectively the R G and B levels of the color specified for each reflectivity range As regards to reflectivity values equal to 46 dBZ in the example of the figure the color used is 021 defined by the following levels R 255 G 81 B 34 Each color is coded on 3 x 255
65. cecceccecceccuccucceeceeueceeeaecaesaeeaeeaeeaueceecuesuecuecuesuesareueeateaes 59 303 ARCHIVE FOLDER a akt tis ad l nt ka a a ki kt m a e e n kk l n e A a e a 61 3 34 GENERAL CONFIGURATION ei ww otis kd ati tat kd ways l tt el ok lk a ka ask a kan a ak kd ek e ak kk a a e 62 3 39 LOG DATAARCHIVE TSK oraire at dj t lap ta tid na kk a ca ik kk e a a a tk n kk f ai 62 A JO POTION tizonnay E l a ct fk a da ka A EN n a A fk n a e 63 3 97 ARCHIVE CONFIGURATION sisecciecexecences a its ia ta a a l kn n a l po pk e P pe d 64 3 36 ARCHIVE SOHEDULER acrior rcn Ern ee nee eee ee 65 3 39 REGISTRATION FOLDER attitude n a et l e e EE ka on ke ep da ada 66 3 40 REGISTRATION SECTION bk tt tt tt kt kaka kaa kaa aaa aaa aaa aaa aaa aaa aaa eaaesaesaesaesaesoesoeseesoesonsonsoesoeoonosonaunn 67 3 41 MANAGE REGISTRATION SECTION bab bek bek t takte teat aa aaa aaa aaa aaa aaa aaeaaesaeaaesaeseeseesoesoasoesoesoeooeosonounn 68 3 42 WOOL WIP kep el sti a dtan E pr ea a not se aaa 71 3 43 DATAACO BUTTONS isi itil l in n kg ok asid at an ka a n ak kin iv l pa ke la kk n pk tk oi kk Aa 72 3 44 EXAMPLE OF COLOR MAP uu tt bb kt kt bwaw kwake aaa aaa aaa aaa aaa aaa aaa eaaeaaesaesaesaesoesoeseesoesonsoesoesoesoeosooaunn 73 4 1 FOLDERS STRUCTURE io win ii ki ata am tik ni aid il a ak ki en tt pi kn kl ab k a pp e e ie A pos aaa 75 4 2 FOLDERS STRUCTURE toi asw di iii id ata at at a ak ek a a a a a a a RE A A 75 4 3 FOLDERS STRUCTURE at ai na tot katkat ki ao it
66. csccccssececceescecceneeeceeeeeecsueeeccaueeecsueeeeseueeecsaueeessaeeesseueeessaseesseeees 68 3 5 4 Tooltip Syntax and MACRO 3sene d s ossbntsabki kaye k mayi a oi kl ot ke knn A e RA RD eke e kaba ba a 69 3 6 DATAACO BUTTONS DESCRIPTION fs b s itka mte optiet n dine bod sd de dik ab kon tiran kin bod kk beie e kin k s kaki 12 3 7 GOLOR SO ALE kana vit ao inps naain aE Ete liye tel ana a api yi kb e kt A ip l ol DEN 73 POLDERS STRUCTURE 6bototra tisi otou k viasie in sake anus one gani pat kite ik a So kn e ni oun Bit EAS 74 DIS PWAN Rit fair oti a tir qn pent d ea e e tj bin e e tt ai BA e a e e n pa e e kn e pi a e T 5 1 MOB MODE ease acces on mant ti estat pi late pa ki n ap t tenant pt e arated ii a ti a bek wegen 79 5 2 MAP SETTINGS rare tl ri aye tn a a kt ka la kl e n ke e a EE a e ak pla ik EE kn 80 5 2 1 Layers MANA EMENL adore bois banan be d ob vote kin b f Aaa k t kola ke n s n bat odit ok dio na kaa 82 ELDES Document code Page 2 of 118 Proprietary Information OM 11242 10 01 WR 10X User Manual Server 5 3 ec GG PI FIL TE gt ene a ata mt kt aa e tl Se E e n a nee a ee PE 85 5 4 COMMANDS ON DISPLAYED IMAGE ccccceccccececececececcacaccceuececuauacetetetecuauatataustenecvsnstsnsneneatanaes 86 5 5 MWENS ENA 2 e set atan vtr kt nt otan m a a ee n wa P E ane rain e ata 88 SSA FIle ea vit kad kay ea vi aye e l etat sa e ne a n a a EEE E e ak ee ei 89 5 5 1 1 Image MANAG MYE N l k el sie p dio
67. cut controls allow to respectively forward or back a zoom level The image zoom can be done with both a steady image and during the movie loop The following figures are an example of the zoom function Work mode Automatic selection Show the last 50 Last date selection From 27 02 2010 Interval date selection scale From 06 07 2010 Mi to Manual selection From 04 04 2010 Mil to Enable Path DIIWR 10XIEvento 2010 04 04 gt WEA pitwa toxtarchive Map settings ivii Background Iv Radar Image Iv Nations iv Regions Ivi Provinces _ Municipalities gi Default Mark Iv Cities Iv Cities amp Town _ Rivers GIF Products filter mle ammo n oo T Rae End loop delay sec 2 MI 400 201004042142 B 0720 0000 C GIF Fig 5 46 Zoom image example 1 Document code ELDES OM 11242 10 01 Proprietary Information Page 109 of 118 EP DES WR 10X User Manual Server W DataView ME i File View Settings Utility Tools 5 Radars and Products LIL i r er aaa ag won Settings LJ Default Radar Si i a Work mode YMI i Automatic selection PPI Show the last 50 _ images RHI Last date selection From 27 02 2010 v Interval date selection From 06
68. d range step expressed in meters integer on 4 digit e HEADER_ELEVATIONSTEP Integrated selected elevation step expressed in decidegrees integer on 4 digit e HEADER_AZIMUTHSPEED Nominal antenna elevation speed for antenna sector movement during the RHI scan operation This field is expressed in decidegrees integer on 4 digit e HEADER NUMPULSES Numbers of pulses integrated on specified ray integer on 4 digit e HEADER_MEANNUMPULSES Average numbers of pulses integrated on total ray integer on 4 digit e HEADER_BB Estimated Bright Band quote expressed in meters If the Brigth Band quote estimation algorithm is disabled property selectable from DataAcq interface or Bright Band non detection this field value is O e HEADER _DATAFORMAT Number of data bits the same for header and data On each row the header of 24 integer field is followed by a data field consists of a number of records depends on the range and range step parameters Each data record is named cell and has a reflectivity average value appropriately coded in levels within 0 2 HEADER_DATAFORMAT From the coded reflectivity value it is possible to obtain the reflectivity value through the following relation dBZ level q_Z2Level m_Z2Level m_Z2Level 2 DataFormat 1 95 5 32 q_Z2Level 2 DataFormat 1 x 32 95 5 32 In case of RHI scan the azimuth position of all rays does not change Unlike what ab
69. d values can be modified by the user while the PRF value can not be modified ELDES Document code OM 11242 10 01 Proprietary Information Page 45 of 118 EP DES van User Manual Server In the Radar setting section it is possible to set the radar ofisets e Azimuth offset degrees increasing this value in a positive direction the map rotates of the same degrees clockwise e Elevation offset decidegrees this value sets the offset expressed in tenths of degrees for the correction of the antenna storing position HOME position means 0 elevation For WR10X CE configuration this value is forced to 0 and it can t be modified In fact in this case the antenna elevation is manually performed e Gate offset it is the number of gates 90 m the minimum range resolution to set the range offset related to data acquisition The 0 value means that no range offset is applied for the data acquisition _ANote These values are set during the installation and setup procedures It is recommended not to change them Putting a flag on the Enable noise filter option the noise filter is applied and it s possible to choose between Automatic or Manual as shown in Fig 3 26 e Manual the Noise Level is the a static value measured in laboratory and it is multiplied with the Log threshold to get the noise threshold logarithmic value e Automatic in this case at the beginning of the schedule the processor performs a noise es
70. directory according to the following hierarchy e lt archived data folder gt e year e month e day Ex Archive gt PPI gt 2008 gt 12 gt 01 It is also possible to apply the rules related to the specified action to a second folder characterized by the Enable action rule on secondary directory parameter Archived files on this last folder are placed according to the hierarchy listed above 3 4 5 Scheduler In the Scheduler folder it is possible to schedule the data archiving activity Clicking on the Add Modify schedule button it is possible to open the window related to the archiving schedule This window is similar to that related to scans scheduling for further details see par 3 1 5 Clicking on the Remove schedule buiton it is possible to remove the set scheduling after clicking on Yes at the acknowledgement request General configuration Acton Archive configuration Scheduler Scheduler Schedule name Next execution Fig 3 38 Archive Scheduler ELDES Document code OM 11242 10 01 Proprietary Information Page 65 of 118 EP DES van User Manual Server 3 5 Registration The Registration folder includes all parameters necessary to manage and display products integrated in the system YO DataAcg Data acquisition and signal processing manager ioj x Registration Manage registration Manual registration PPI A DataAcq A DataAcq A DataView A DataView
71. e RHIDimFilter parameter is used in order to define the dimension of the square mask that is used during the filtering Generally in case of RHI acquisition it not necessary to apply this filter it is recommended only in case of excessive residues on the image ELDES Document code OM 11242 10 01 Proprietary Information Page 117 of 118 EP DES van User Manual Server The RHIDimFilter parameter is set to 3 for default it is recommended to set the parameter not exceeding the value 5 in order to avoid to locally modify the intensity related to the observed weather phenomenon 8 1 5 NoiseDataCollection This section allows to enable the saving on disk of the noise data acquired during the schedule running The files are saved in the folder WR 10X DataFiles RAW the data aren t managed by the storing tool Only for debug activity or for short time intervals it is recommended the use of this function The stored file name format is Noise_ggmmaaaahhmm_ss mat For example the file Noise 060220131457 53 mat includes noise data of the day 06 02 2013 at time 14 57 and 53 seconds The files are saved in mat format importable without additional processing in Matlab software environment For the format of the information related to the file please refer to the RAW data description see chapter 3 2 1 the format is the same ELDES Document code Page 118 of 118 Proprietary Information OM 11242 10 01
72. e and range resolutions according to the Tab 3 1 For example if the selected range is 2Km and the selected range resolution is 300m the range bin number for each row is 72000 300 240 Each row Is related to ONLY ONE transmitted pulse ELDES Document code OM 11242 10 01 Proprietary Information Page 47 of 118 EP DES van User Manual Server lt follows that the line number in the RAW file is related to the antenna speed in fact with a PRF of 800 Hz and an antenna speed of 20 s the time necessary to complete a round will be of 18S So SOU 18 14400 lt follows that if the antenna speed is constant at 20 s to complete a round angle the RAW data file will be composed of 14400 In short it is possible to say that if it is intended to integrate all values related to the first rang bin for an antenna beam width of 3 it will be necessary to take all samples included in the 6 column starting from the line progressive number of 2868 to number 2761 see example In the example it is instead clear that samples composing the first range bin are not 120 but only 107 2868 2761 the same can be said for all range bins This is due to the real antenna speed which is not in this case equal to 20 S but to 22 43 S As the PRF is fixed to 800 Hz and the sampling is fixed the file includes only 12940 lines against the theoretical 14400 This example has been made to highlight that the processing algorithm REMAPS the cells S
73. e by means of the sw application GeneratoreMappeClutter exe are still too noised The CMAPDimFilter parameter is set to 3 for default it is recommended to set the parameter not exceeding the value 5 in order to avoid to locally modify the intensity related to the observed weather phenomenon 8 1 3 PPIMedianFilter This section allows to enable and to set a median filter to be applied to the matrix of integrated data PPI z related to PPI acquisition PPiMedFilt 0 no one filter is applied PPIiMedFilt 1 two dimensional Median Filter applied on the matrix of integrated data PPI z In this case only the PPIDimFilter parameter is used in order to define the dimension of the square mask that is used during the filtering Generally it is advisable to activate this function in any case for the residual spikes suppression from the binary matrix that is used as input for the processing The PPIDimFilter parameter is set to 3 for default it is recommended to set the parameter not exceeding the value 5 in order to avoid to locally modify the intensity related to the observed weather phenomenon 8 1 4 RHIMedianFilter This section allows to enable and to set a median filter to be applied to the matrix of integrated data PPI z related to RHI acquisition RHIMedFilt 0 no one filter is applied RHIMedFilt 1 two dimensional Median Filter applied on the matrix of integrated data PPI z In this case only th
74. e field Products filter Range te without clutter 72 km pen i m C with clutter Elevazione 10 E ovon lw BA Fig 5 11 Products filter ELDES Document code OM 11242 10 01 Proprietary Information Page 85 of 118 EP DES anan User Manual Server 5 4 Commands on displayed image During the images display in the central window it is possible to make some operations e Images play movie loop e Movie loop reproduction stop e Movie loop pause e Manually move to the following or previous image e Move to the first or the last available image Controls which are below player commanas allow to modify respectively the update speed of the movie loop frames from 10ms min to 1000ms max and the time between the end of a loop and the beginning of the next one titan ai toi otan oo tate ED iritan i m5ec End loop delay sec Fig 5 12 Control bar The progress bar which is below shows the movie loop progress the file name which is currently being processed is shown in the read only text box next to it The representation of colors used by the displayed product image is placed on the control bar side Moving the bars the color related to its position in the displayed image is removed The purpose is to highlight the centers or the end of the disturbance characterized by a lower reflectivity e I Fig 5 13 Color management bar Clicking with the left mouse button on the displayed image information related
75. ea tea teseoaesaesaesaesoesoesoasoesoasoesoesonoonoon 42 FIG 3 25 SIGNAL PROCESS FOLDER ka bb bk kte kt kt kaa kaka kaka kaa aaa a aaa aaa aaa aa eeaaeeeaeeeseseesesoesoesessesoesoasoosnoonsnnnnn 43 FIG 3 26 ENABLE NOISE FILTER SECTION 2c 0ccecceeccecceeceeceececceccuecuececaecaeeaesaeeaeeaueceeseeseesueseesaeenseaees 46 FIG 3 27 RAW FILE STRUCTURE cccccceccecceccecceeceeeceeaeecueceecuecuecuececuecaecaeeaesaeeaeeaeesueseeceesuesueeaesaeeaees 48 FIG 3 28 GENERAL FOLDER 2ceccececceceececeececeececeececeeaeceeaeceeaececuececueaecueaecueaeceeaeaeenesesueaesueaeseeaesutatans 55 FIG 3 29 SIGNAL PROCESSING LOG cecceccecececcecceceeccceececaececeeaecaecueceeaecaecuesesaecuecueaesesueseeaesneeneaeeas 57 FIG o JO DA TAACO SK LOG kanta out ki oti eti kk ki kal e ii e soi iye ki ski klou kib rA PEER eti kit ki klan 58 FIG 3 31 SIGNAL PROCESSING ERROR LOG bbl bett kt kaka kaka aaa aa aaa aaa aa aaa aaaeaeaasoeseesesoesoeseosesoesoesooanoonsnnenn 59 ELDES Document code Page 4 of 118 Proprietary Information OM 11242 10 01 WR 10X User Manual Server FIG FIG FIG FIG FIG FIG FIG FIG FIG FIG FIG FIG FIG FIG FIG FIG FIG FIG FIG FIG FIG FIG FIG FIG FIG FIG FIG FIG FIG FIG FIG FIG FIG FIG FIG FIG FIG FIG FIG FIG FIG FIG FIG FIG FIG FIG FIG FIG FIG FIG FIG FIG FIG FIG FIG FIG 3 32 LOG DECISION THRESHOLD 0cccec
76. eclutter parameters For further information refer to section O On the left of each line the specific data and time is reported The file contains the NOISE PARAMETERS MEASUREMENT section that shows the outputs of the noise algorithm in particular the Noise Mean Level indicates the noise mean value expressed in a d converter levels The second section shows the processing outputs of the acquired data for each elevation In the first line as the upper section the date and hour of the scan is reported The second line shows the scan range 36 or 72 Km The third line shows the elevation value at which the scan has been run After these preliminary information the main parameters through which the signal processing has processed the scan are provided The number of cells which had a StdDev lower than the Low Threshold called Ground Clutter The number of cells which had a StdDev higher than the High Threshold called Weather signal The number of cells which had an intermediate StdDev called Mixed Signal It is also possible to detect speed errors in the antenna rotation Document code ELDES OM 11242 10 01 Proprietary Information Page 57 of 118 3 3 2 EP DES WR 10X User Manual Server DataAcqTsk log The purpose of this log file is to save in a file all messages coming from the DataAcq Tsk module This function can be useful in case of system fault to analyze the scan process point in which the pr
77. ed to data archiving or removal The archive files can be found in the Archive sub folder related to the software directory installation DataAcg Data acquisition and signal processing manager ss son wie we 10 Li General configuration Archive configuration General configuration IV Show DataArchiveTsk video log IV Save DataArchiveTsk log on file DataArchiveTsk log E Display window application l Save profile Load profile Fig 3 33 Archive folder l Save and Exit l Save The Archive folder is divided into the following sub folders General configuration Action Archive configuration Scheduler which will be detailed described in the following paragraphs ELDES Document code OM 11242 10 01 Proprietary Information Page 61 of 118 EP DES 3 4 1 U General configuration The General configuration folder includes the following options e Show DataArchiveTsk video log putting a flag on this option the log messages related to the application which archives data will be displayed on screen e Display window application putting a flag on this option the display on screen of the DataArchiveTsk application window is enabled This shows all tasks that are being carried out e Save DataArchiveTsk video log on file DataArchiveTsk log putting a flag on this option log messages are saved on the DataArchivelskyyyymm log file yyyy year mm month in the WR 10X Bin LogFiles folder
78. eeeeeeeeessseeaeeeeeeesssaaaeess 52 3 3 GE NE aces ft sett a a n st ea cma sca a a de eae ane a re pa Fe n ea ea ar en rit 55 FO SONE FOC SSSI OO kote ae e ai ot ponn pei ba abo skin oo antik at ese nat io lipa avons ee kes kn foto pede i 56 392 D2 fe 6 9 SA OU ekta ine ta kab prat b at n ta n e af pi ras e kk e e ne ee re eta eee role ennan pe eon 58 33 3 SINABIOCESSINGE NON OU k eka dren kk p anan e ld seki ske pisin pot ke pise a anpii sas aske ek dep 59 3 3 4 Decision Threshold Log file cccccccccccssscecceseecceeeeecseseeceegeeeseueceeseseessaueeesseseessaueeessaseesseeees 59 3 4 ARONNE oti ta aye kt ti ip E e e e e n a e ef ko a ee tie pous kle siel a apa 61 341 G Nn rak COMMUTATION aveti vese e a pt fe ka l an n n e a L a di an a n ak a n a kr be L ba 62 Bee Lod DataArchive TSK an dis iii ii 0 it ta at pa no E 62 DAN 2 6 0 da oka ot et af la Go e ee it pe Do a A ta Defi ON a ae eee sens 63 944 Archive GONNQUFAUON k de viris annik bk a ii ok bb p n ate pin d ba kan e n kin intak d ba kis aran k te m n tisi kale 64 GAS SONE EN ga er laten st pk ed n E on elan E pa aa n pa a al a an a e e es ka on e tt n ep sin 65 39 eS 1g Wey ATION eaa a e at E ee 66 33910 TACOS I GMS CC HON esseede a a a E ea Eea a ae aid no ii cee 67 3 5 2 Manage registration section cccccssceccseseecceseeeceeseecceeeeccaueeeceueeeesaseessaeesseseessegeeessaeeeessaeees 68 3 5 3 Registration parameters cccc
79. er cessa di essere inattivo Risparmio energia Mon avviare l operazione se l alimentazione a batterie nterompi l operazione all avyio dellalimentazione a batterie Riattiva il computer per eseguire l operazione Fig 3 21 Scheduled task settings Document code ELDES OM 11242 10 01 Proprietary Information Page 39 of 118 EP DES van User Manual Server 4 Note Do NOT change settings directly from the Windows scheduler in order to avoid misalignments and conflicts Clicking on the Remove schedule button which is in the Scheduler folder the selected scheduling is removed after clicking on Yes in the window related to the operation acknowledgement request DataAcg 2 Do you want remove schedule Fig 3 22 Scheduling removal 3 1 6 Products The Products folder includes all general configuration parameters General Configuration and parameters related to the different products registered in the system Products ELDES Document code Page 40 of 118 Proprietary Information OM 11242 10 01 vann EDES User Manual Server Scan mode _ General Configuration EEA Predicts scan setting Communication E Show GestObjTsk video log Show elaborations details Time Save GestObjTsk log on file GestObjTsk loa Show GestObjTsk window LocalTime UTC J Products Drag a column header here to group by that column Enable Name Description RHI Range Height I
80. es rnn yyyymmddhhmm Scan DataAcq xml PPl rnn yyyymmddhhmm B RRRR rrrr aaaa EEEE C z PPlI rnn yyyymmddhhmm B RRRR rrrr aaaa EEEE U z RHI rnn yyyymmddhhmm B RRRR rrrr eeee AAAA C z RHI rnn yyyymmddhhmm B RRRR rrrr eeee AAAA U z The Scan file is a text file only including a string specifying the name of the active scan information included in the file name is the same information for the cab file described above Scan means a series of settings configured and stored in ELDES control and management environment which can be called by the scheduling or instantaneous execution mode The xml file is the current configuration file annexed by the server application to the compressed data package transmitted to a FTP space or a shared folder and used by the client application to realign the local settings display with the remote settings The z files are binary and include information related to the scan here described RRRR is the range expressed in hundreds of meters rrrr is the range resolution expressed in meters aaaa is the azimuth resolution expressed in tenths of degree EEEE is the elevation value expressed in tenths of degree eeee is the elevation resolution expressed in tenths of degree AAAA is the azimuth value expressed in tenths of degree For example about PPI the files indicate that the scan has been run at a EEEE elevation and aaaa azimuth resolution with a RRRR range and rrrr ran
81. es of parameters divided into two categories DataAcq and DataView can be set in both sections described in par 3 5 1 and 3 5 2 ELDES Document code Page 68 of 118 Proprietary Information OM 11242 10 01 vann EDES User Manual Server Both categories are described in details below DataAcq 1 Name indicates the product name 2 Description indicates the complete product name 3 Dil path indicates the path which leads to the product dll which will be integrated in the system The specified file won t be modified on the contrary it will be copied in the WR 10X Bin Obj folder in which the system places all files related to the registered products 4 Ctf path indicates the path which leads to the product dil with the ctf extension which will be integrated in the system The specified file won t be modified on the contrary it will be copied in the WR 10X Bin Obj folder in which the system places all files related to the registered products 5 Acronym is a text string composed of three letters which univocally identifies the product 6 Config file indicates the configuration file name managed by the product 7 Level indicates the level of the registered product As regards the server application it is possible to register only First Level products DataView 1 Color table path indicates the path which leads to the file including the product colors specification The specified file won t be modified on the contra
82. es will be available e Browser Radars and Products shows or hides the Radars and Products section exactly the same as clicking on the button e Off line Radars shows in the Radars and Products section also those radars which during the configuration alignment procedure between Server and Client are not updated in this way it is possible to go on seeing the products images generated by the involved radar This option makes sense only in a Client system e Common Products View enables or disables the common setting imposition for all products according to what is specified in the proper configuration window accessible from the Setting menu Document code ELDES OM 11242 10 01 Proprietary Information Page 97 of 118 EP DES anan User Manual Server 5 5 3 Settings Selecting Settings from the menu bar the following entries are available e Radar site opens a window in which it is possible to enter the radar site altitude expressed in meters latitude and longitude expressed in degrees GE Radar Site Settings RadarSite Settings Altitude From sea level metres Site latitude Site longitude Fig 5 35 Radar site settings e Product view opens a window in which it is possible to configure two sections The first section allows to choose if the settings related to a first level product product among those registered and so available in the proper drop down menu have to be applied to all other first level products
83. g on the Clear button all edited fields will be cleared of their values Registration Manual registration DataAcq pa Dataview mn E E E Fig 3 40 Registration section ELDES Document code OM 11242 10 01 Proprietary Information Page 67 of 118 EP DES anan User Manual Server 3 5 2 Manage registration section In the Manage registration section it is possible to display modify or delete products included in the system Manage registration FFI ae oP DataAcq DataView on LA RHI zx DataAcq m DataView se LA Fig 3 41 Manage registration section Each of the above mentioned operations must be carried out after clicking the Modify button lt will be now possible to edit parameters included in the table and save the new values clicking on the Save button Once clicked buttons and values will be read only again except for the Modify button which will allow to carry out a new changing and the Restore button which will restore values to the version previous to the change lf it is intended to remove an existing product it will be sufficient to select its name or any of the fields below click on the Delete button always after clicking the Modify button and acknowledge the related request As in the previous case if it is intended to undo the change it will be sufficient to click on the Restore button For WR10X CE configuration the RHI section is not enabled 3 5 3 Registration parameters A seri
84. ge resolution from the rnn radar at the yyyymmddhhmm scheduled date ELDES Document code Page 74 of 118 Proprietary Information OM 11242 10 01 vann EDES User Manual Server The PPI and RHI acronyms indicate the products with the same name C or U sections show de cluttered and non de cluttered data respectively The folder C Program Files WR 10X here is shown Ji Bin Wi DATA Jo DataFiles ii jip di Maps m RAW Ji ToSendFiles Ji RHI Ji Archive Fig 4 1 Folders structure The DataFile folder includes 4 folders named DATA PPI RHI RAW In the SERVER version z and scan files are archived in the DATA folder while the compressed version intended for the Client is momentarily put in the FTP space as above mentioned lt is important to specify that the z binary file C type decluttered and U type files non decluttered are ALWAYS included in the CAB file The Client will choose which file to use for the display The generated graphic products files are put in the PPI and RHI folders These can be JPEG TIF BMP GIF PNG type according to the configuration chosen see par 3 1 6 and if the products generation has been enabled On the contrary the so called raw files that is to say not processed which can be saved in r or txt format are put in the RAW folder The name syntax for these files is similar to the above mentioned one The SERVER version has an additional folder
85. hr This kind of filtering is suitable for spikes Suppression an example of spike noise is shown in Fig 8 1 ELDES Document code Page 112 of 118 Proprietary Information OM 11242 10 01 mann EDES User Manual Server Fig 8 1 Spike noise example It is recommended to set the LevelRejectThr value to 30 levels and decrease it until interfering signals are not present in any case it is advisable to choose a LevelRejectThr value greater or equal to 20 levels in order to avoid weather signal suppression Avoid to set the DimFilter parameter value 5 in order to avoid to locally modify the intensity related to the observed weather phenomenon The DimFilter parameter meaning in case of Median Filter is explained by the Fig 8 2 ELDES Document code OM 11242 10 01 Proprietary Information Page 113 of 118 EP DES anan User Manual Server Example of PPI sector not in scale The real applied filter dimension is 2 DimFitter 1 x 2 DimFilter 1 In this case 5x5 T Fig 8 2 DimFilter parameter meaning in case of MedianFilter IntReject 2 one dimensional SpaceFilter applied on RAW data In this case only the LevelRejectThr parameter is used in order to define the threshold in levels under which the filtering process will not apply The filter is locally applied only for range gate for which the gap in levels between the azimuth current position and the adjacent one lag
86. ianFilter cc ccccccccccccssececceeececeeeceeceeececeeccesseeceeseseeessueeeseaecessegeeesseeeesaaeees 117 8 1 3 PPIMedianFilter ccccccccccccececsceccccececsceccucececscucaucececseuausecseueauausenscauaueusecseatauaenecseavaunenecas 117 Gi UTICA b v 6 es tate kaa e a ka e e e e ot te a ae te e e n ka R 117 8 1 5 NoiseDataCollECtiON c ccccccccececceccceccccecccecuccecuccecuececueaececaeceeaueueaececececaeaecsenecseaecueaeseeaeeass 118 ELDES Document code OM 11242 10 01 Proprietary Information Page 3 of 118 WR 10X User Manual Server List of Figures FIG 2 1 INSTALLMANAGER FOLDER 0 kte bbl kte kte kaka teat aa aa aaa aaa aaa aaa aaa tea teeteesesessesessessessessaesoesonsonsousonssnosnnaunn 7 FIG 2 2 INSTALL MANAGER hbi bbl bb kt kt kwake kaa kaa aaa aaa aaa aaa aaa aaa aaa aa sea teeseesessessessessessesseaseosoasoasonsousonssnosnnounn 8 FIG 2 3 WR 10X INSTALLSHIELD WIZARD bk bk kt tk tt kk a kaw ka kaka aaa aaa aaa teat aaa ase asesaesaesessaesaesoesoesoesoesoesoeosnoonnn 9 FIG 2 4 WR 10X INSTALLSHIELD WIZARD SERVER ccccceccecceccecceeceeceeceeenecaeeaeeceeceeceeceecueeueeueenseaees 10 FIG 2 5 INSTALLATION WIZARD PATH 2 ceccecceceeeceeceeeceeceeceecuecuecuecuececaecaeeaesaeeaeeaueaeeceeseeeueeuteuesaneaees 11 FIG 2 6 WR 10X INSTALLSHIELD WIZARD SUMMARY cccceccecceccecceeceeceeeeeceecaeecuecueceecuecueeueeneeuseaees 12 FIG 2 7 WR 10X INSTALLSHIELD WIZARD EN
87. idegrees integer on 4 digit e HEADER NUMPULSES Numbers of pulses integrated on specified ray integer on 4 digit e HEADER_MEANNUMPULSES Average numbers of pulses integrated on total ray integer on 4 digit e HEADER_DATAFORMAT Number of data bits the same for header and data On each row the header of 23 integer field is followed by a data field consists of a number of records depends on the range and range step parameters Each data record is named cell and has a reflectivity average value appropriately coded in levels within 0 2 HEADER DATAFORMAT From the coded reflectivity value it is possible to obtain the reflectivity value through the following relation dBZ level q Z2Level m Z2Level m Z2Level 2 DataFormat 1 95 5 32 q_Z2Level 2 DataFormat 1 x 32 95 5 32 In case of PPI scan the elevation position of all rays does not change Unlike what above described for RAW data the azimuth and elevation positions are not involved by the offset ELDES Document code OM 11242 10 01 Proprietary Information Page 51 of 118 EP DES anan User Manual Server In particular the azimuth position of each ray expressed in encoder steps shows the angle to which the ray closes for example if the azimuth resolution selected is 3 as regards the first cell the azimuth position is 17 encoder steps corresponding to 3 With reference to the example mentioned above PPI A00 20
88. ilter is locally applied only for range gate for which the gap in levels related the azimuth current position and the two adjacent ones lagi and lag2 is greater or equal to the LevelRejectThr value This kind of filtering is suitable for suppression of radar to radar interfering signals having a very quickly variable PRF value among three PRF near values ELDES Document code Page 116 of 118 Proprietary Information OM 11242 10 01 vann EDES User Manual Server It is recommended to set the LevelRejectThr value to 30 levels and decrease it until interfering signals are not present in any case it is advisable to choose a LevelReject Thr value greater or equal to 20 levels in order to avoid weather signal suppression 8 1 2 ClutterMapMedianFilter This section allows to enable and to set a median filter on the clutter maps generated during the radar operation By means of the CMAPMedFilt it is possible to select two modes CMAPMedFilt 0 no one filter is applied CMAPMedFilt 1 two dimensional Median Filter applied on the clutter maps In this case only the CMAPDimFilter parameter is used in order to define the dimension of the square mask that is used during the filtering Generally it is not necessary to activate this function this function is dedicated to extreme cases where the various functions applied to remove the noise spikes don t get the desiderated results or rather the clutter maps viewabl
89. indow display UTILITY allows to have access to the PREFERENCES window The following figure shows the PREFERENCES window ELDES Document code Page 106 of 118 Proprietary Information OM 11242 10 01 WR 10X User Manual Server EP DES LayerMapCreator Ioj x VIEWER UTILITY GENERAL Nation Database PARIAN Nations Boundaries e r y a pen eten File Selection Ic Program Files WR 10X Bin CARTOGRAPHY 1 DEM G_IN iss RJ tw Gf1s B _ sercoior SIN 16 Rf 106 G 255 B SETCOLOR GOUT fow Rfosw Gfos B secoor SOUT fre RI 106 G 25s B _ SETCOLOR NATIONS white M line color 16 line width REGIONS white v line color 16 line width PROVINCES white X line color 12 line width MUNICIPALITIES white line color os line width CMTES black v char color 11 0 char width ctes cities type town population RIVERS bive X line color 10 line width ROADS frea line color 10 line width RAILS oreen z line color 10 line width l Binary File Generation Fig 5 45 Layer Creator PREFERENCES window DEFAULT DEFAULT DEFAULT DEFAULT DEFAULT PERE RR ERE From the PREFERENCES window it is possible to define options for all types of layers managed by the application Except for the DEM and CITIES layers which have additional options available for all other layers it is possible to select the line color and the line width As regards the CITIES layer it is possible to select the
90. ing values as shown in the figure the result will be that cells including clutters will be displayed in gray color besides the usual display of cells including weather signals ELDES Document code Page 110 of 118 OM 11242 10 01 Proprietary Information EPDES LWRAOX User Manual Server 7 Clutter Map Verification This chapter describes the software application tool for the Clutter map verification This tool allows to generate images corresponding to the clutter map To execute the tool on the provided installation CD select the Tools folder and launch the GeneratoreMappeClutter exe file The application asks for the input folder select the WR 10X Bin CMap path on the folder installation software The tool creates a graphic file image for each file binary file clutter map located in the CMap folder The Fig 7 1 shows an example of clutter map using the following acquisition data e Radar A0O e Range 72 km e Range resolution 300 m e Azimuth resolution 3 e Elevation 1 Fig 7 1 Clutter Map image example ELDES Document code OM 11242 10 01 Proprietary Information Page 111 of 118 EP DES van User Manual Server 8 Additional Features For the Additional Features management it is not foreseen a software MMI So the Server operator has to carry out the related settings by means of the data entering in SignalProcessingConstructor xml file 8 1 Settable Functions In the file SignalProces
91. ion option to cut off the call at the end of data transmission ELDES Document code OM 11242 10 01 Proprietary Information Page 35 of 118 EP DES van User Manual Server 3 1 5 Scheduler In the Scheduler folder it is possible to schedule radar scans Scheduler Scan scheduler Schedule name Next execution Add Modify schedule Remove schedule Fig 3 14 Scheduler Clicking on the Add Modify schedule button a window related to scheduled tasks typical of Windows will appear as shown in the Fig 3 15 ELDES Document code Page 36 of 118 Proprietary Information OM 11242 10 01 WR 10X User Manual Server TSK Default Radar Scan_0 Operazione Pianificazione Impostazioni ENDER eski sew step Gea lila Esegui misWA 1 0 BinDatadcgl sk exe Default Radar Scan Sfoglia Da CAWWR 10 ver 3sBin Commenti i 0s Datadcg application Esegui come ELDES wr Oe mposta password e Esegui solo ad accesso effettuata lw Attivata l operazione pianificata viene eseguita all ora specificata Fig 3 15 Task execution window In this screen it is possible to activate or not the scheduled task and decide the execution criteria Putting a flag on the Activated option the procedure will be run at the specified time Selecting the option Run only after the access the choice is to run the procedure only when the user who creates it has completed the operating system login Removing the flag the po
92. is instead possible to enable different azimuth steps together with the related parameters and set the initial and ending elevation with which it is intended to carry out the procedure Selecting the Automatic RHI check box azimuth steps will be disabled and the system independently calculates the most appropriate azimuth value to carry out the RHI Two search systems related to the azimuth direction along which the next RHI scan will be run can be set Max intensity and Max water s cells number on ray ELDES Document code Page 26 of 118 Proprietary Information OM 11242 10 01 vann EDES User Manual Server In both cases data related to the volumetric scan composed of n polar PPI are reproduced on the horizontal plane and put on the Cartesian axes before proceeding with the next processing In the first case the algorithm which controls this function will find the azimuth value for which the maximum reflectivity value has been found on the Cartesian reflectivity map if the reflectivity value of the maximum group which has been found exceeds a specified threshold the azimuth direction found is used to run the automatic RHI scan In the second case the number of cells whose reflectivity exceeds a determined threshold is measured and stored for each ray of the Cartesian reflectivity map the azimuth direction used for the next RHI scan is that of the ray in which the number of cells marked with water is the maximum The integration
93. kika kb a l a kl kte kk ne k k j a e kika osi ase k don at Nk AA seke 89 S52 MONN acts etre f e eki die disip ti f k do adastcaiasandcdbadacnddecumace dh adaetdatarandaceedacaddaatnanedhidastdetaanaccbedasmadects 97 RNC Sah ke n e tk ee e kk ek on a ot a e e e e n a ot e k ke ie ke fot bb 98 OWA LIY Soon ae seten ki ice tea di po ai ka kn e pl Ga ka e E a aka ae e e ta kose e n eat 99 5 5 4 1 Man NC ANON ti tin pt vin tt EE sp pl snes t kt po ta Bek NA et Sak 99 5 5 4 2 AWA KE FO AN Ok et et ta kt kt pe n l tl a kek e ka k eka ed e ke oceans nea e An et ken e aba Ze 101 5 5 4 3 Layer CC NON it kil kn taa dap n eko kk aa ie kisa asa ol ee ske kass pei so abo te dile dear ies 103 BA WOOL nove cecdeedeenateatmicse die we disa ea dete e oue ee kle tis e a katye a l ken ek ae a et a a e ke ee Peman ee ka za 109 CLUTTER AREAS DISPLAY cccccccccccccccececucecccceuececuuausueuauecucuaeauenenacucuausuenenacucusesusuenecucusuaueneneceas 110 CLUTTER MAP VERIFICATION ccccececececcccccacecececccuacacaceuececuauacatetececuavausuauenececuststsueneceavansusneneneas 111 ADDITIONAL FEATURES cccccccececccceccccececeacececceueceauauectaueceauauecesueceauanestsnecesustesusuecesuscesusueceauecs 112 8 1 SETTABLE FUNCTIONS IN THE FILE SIGNALPROCESSINGCONSTRUCTOR XML 02 0eeeeeees 112 8 1 1 Interferent Rejection seek tas kiwo kita n a l ak ol kl ae n el nn ka l an a el senhdwocuiesicenstsesdeatuedweeaseeetiick 112 8 1 2 ClutterMapMed
94. l Configuration window includes the following options which can be simultaneously selected e Show DataAcqTsk video log putting a flag on this option the application log messages are displayed e Save DataAcqTsk video log on file DataAcqTsk log putting a flag on this option the log messages are saved on the DataAcqIskyyyymm log file yyyy year mme month in the WR 10X Bin LogFiles folder e Save advanced analysis log on file selecting this option messages related to the log of the signal processing module will be stored in a file called ELDES Document code OM 11242 10 01 Proprietary Information Page 55 of 118 EP DES van User Manual Server SignalProcessingyyyymm ixt yyyy year mm month in the WR 10X Bin LogFiles folder Apart from the status of this option in the same folder a log file including synthesis information useful for the declutter parameters setting is continuously updated Decision T hreshold txt e Show signal process details putting a flag on this option a log including additional information about the signal process execution will be displayed e Display window application putting a flag on this option the display on screen of a shell in which the flow of all tasks run by DataAcq Tsk is shown is enabled e Advanced work mode selecting this option a special configuration window protected by Password is enabled This is used only during the start up procedure in order to determine the optimum thresholds
95. l laal Color Co Font verdana a Size EZ iv Bold iv Italic Transparency 0 255 Position Page Range C In front MAN C Pages Enter page numbers and or page ranges Q Behind separated by commas For example 1 3 5 12 cone Fig 5 30 Background text As regards the text to be entered in the Text field it is possible to choose font size color transparency type of inclination ELDES Document code OM 11242 10 01 Proprietary Information Page 95 of 118 WR 10X User Manual Server Watermark ext toma Ae Maem Size mode Clip Horizontal alignment Center vertical alignment Middle L Tiling Transparency 0 255 w Position Page Range N In front Al O Pages Behind Enter page numbers and or page ranges rido separated by commas For example 1 3 5 12 Clear All OK Cancel Fig 5 31 Background image As regards the image which has to be inserted exploring the PC hard disk after clicking on Load image it is possible to choose position in the page alignment transparency etc lt is possible to choose for both text and image which pages the background text and or image have to appear on Page Range options Toolbar Icons Icons displayed on the toolbar can be modified putting a flag on options related to the buttons which it is intended to display as shown in the following figure Z lig i gt i Add or Remove Buttons gt Toolba
96. lation Wizard Path ELDES Document code OM 11242 10 01 Proprietary Information Page 11 of 118 EP DES anan User Manual Server The Fig 2 6 shows a summary of the selected options for the installation click on Next gt button to start the installation WR 10X InstallShield Wizard Start Copying Files Review settings before copying files Setup has enough information to start copying the program files IF you want to review or change any settings click Back If you are satished with the settings click Next ta begin copying files Curent Settings WATS Installation type Server Installation Directory C Program Filesw A 1 Oe Cancel Fig 2 6 WR 10X InstallShield Wizard Summary ELDES Document code Page 12 of 118 Proprietary Information OM 11242 10 01 van EDES User Manual Server At the end of the installation the Fig 2 7 is shown press Finish to exit the WR 10X installation WR 10X InstallShield Wizard InstallShield Wizard Complete Setup has finished installing W A 10 on your computer Finish Fig 2 7 WR 10X InstallShield Wizard End Document code ELDES OM 11242 10 01 Proprietary Information Page 13 of 118 EP DES anan User Manual Server 2 2 2 License Server Service Installation lf you have selected the License Server Service check box on the Install Manager window Fig 2 2 the Fig 2 8 will appear License Server InstallShield Wizard X Welcome to
97. ld txt log file purpose is to save on a file a report which allows to observe the variability of the set parameters related to the declutter filter so this function can be useful for a short and long period analysis 201302 72 00 1 00 300 3 00 99 50 5 27 6 45 10 99 15 5 27 6 45 201302 72 00 2 00 300 3 00 99 44 5 30 6 65 10 99 44 5 23 6 65 201302 72 00 3 00 300 3 00 99 24 5 40 6 71 10 99 65 5 40 6 71 201302 72 00 4 00 300 3 00 99 13 5 51 6 88 10 99 23 5 52 6 98 201302 72 00 5 00 300 3 00 99 10 5 50 6 66 10 99 10 5 40 6 66 201302 72 00 10 00 300 3 00 98 98 5 71 7 19 10 98 98 5 71 7 25 201302 108 00 1 00 450 3 00 99 10 5 15 6 25 10 99 25 5 25 6 40 201302 108 00 2 00 450 3 00 99 34 5 65 6 74 10 99 65 5 30 6 65 201302 108 00 3 00 450 3 00 99 15 5 15 6 32 10 99 14 5 40 6 71 201302 108 00 4 00 450 3 00 99 25 5 51 6 25 10 99 32 5 52 6 55 201302 108 00 5 00 450 3 00 99 95 5 45 6 16 10 99 12 5 15 6 65 201302 108 00 10 00 450 3 00 98 15 5 32 7 25 10 98 42 5 71 7 19 Fig 3 32 Log Decision Threshold The first column shows year and month to which the data are referred The second column shows the range for which the data are calculated The third column shows the elevation value for which the data are calculated The fourth column shows the range resolution expressed in meter The fifth column shows the azimuth resolution expressed in degrees ELDES Document code OM 11242 10 01 Proprietary Information Page 59 of 118 EP DES van User Manual Server
98. list including the paths a menu will be displayed This will allow the user to add or remove a path To specify the path that must be considered for the images search it is necessary to enable the related radio button Manual selection Enable Path Ce WiR 10s Archive gt D WR 10 Evento_2010_04 en Fig 5 6 Manual selection 5 2 Map Settings The Map settings sub section allows to manage the layers which have to be integrated with the different products images The Radar Image layer is the radar processing and cannot be changed or deselected An empty background image map omp located in WR 10X Maps and a polar mark for each range managed by the system 36Km and 72Km are provided by default The last cannot be changed If it is intended to use a mark different from that provided by default it will be sufficient to create a new layer enabling it in place of the one already existing ELDES Document code Page 80 of 118 Proprietary Information OM 11242 10 01 ann EP DES User Manual Server The Fig 5 7 shows an example of a display with the default polar mark and a customized background image One of the four available image format can be selected for the display L GIF C BMP oe PNG EI TIFF A Note lt is important to consider the format of the generated files when selecting this option This format is defined during the product configuration see par 3 1 6 If no file has been generated with the specified f
99. n OM 11242 10 01 vann EDES User Manual Server 2 2 1 WR 10X Installation lf you have selected the WR 10X check box on the Install Manager window Fig 2 2 the Fig 2 3 will appear WR 10X InstallShield Wizard Welcome to the InstallShield Wizard for WR 10 The InstallShield Wizard will install W A 1C on pour computer To continue click Mest InstaI5hialri E l 3 Cancel Fig 2 3 WR 10X InstallShield Wizard Press Next gt to continue ELDES Document code OM 11242 10 01 Proprietary Information Page 9 of 118 EP DES anan User Manual Server Select Server on the Fig 2 4 and press Next gt WR 10X InstallShield Wizard Setup Type Select the setup type that best suits pour needs Click the type of setup pou prefer n Install required Server components Insta orale lt Back Next gt Cancel Fig 2 4 WR 10X InstallShield Wizard Server ELDES Document code Page 10 of 118 Proprietary Information OM 11242 10 01 amann EP DES User Manual Server On the Fig 2 5 select the installation path and press Next gt WR 10X InstallShield Wizard Choose Destination Location Select folder where setup will install files Setup will instal wW A 10 in the following folder To install ta this folder click Next To install ta a different folder click Browse and select another tolder Destination Folde r E Program FileswwA l Oe Browse Cancel Fig 2 5 Instal
100. n menu which appears under the Schedule operation eniry it is possible to select the task recurrence and so the task starting time Pianifica operazione Ora di avyio 9 00 Avanzate Allaccesso dell utente Fig 3 19 Task scheduling Clicking on the Advanced button the options shown in the following figure will be displayed ELDES Document code Page 38 of 118 Proprietary Information OM 11242 10 01 WR 10X User Manual Server Opzioni di pianificazione avanzate Data di inizic venerdi 28 novembre 2008 w Data di fine lw Ripeti l operazione Ogni 10 minut Finoa C Ora tw Durata a4 TI orae fi minuti Se l operazione amp ancora in esecuzione vera terminata all ora indicata Fig 3 20 Advanced scheduling options From here it is possible to set a series of parameters such as the dates range within the scheduling has to be applied the task repetition recurrence etc Entering the Settings folder we will find a series of options which allow to customize the task scheduling TSK Default_Radar Scan 0 Operazione Pianificazione Impostazioni Completamento operazione planificata W Temina l operazione dopo f2 orate g minuti Tempo di inattivit Avywia operaz pianificata solo se il computer rimasto inattivo per minuti Se il computer non rimasto inattivo per tale durata riprava per L minuti Interompi operaz pianificata se il comput
101. n s a tep 9 a tep 10 Azimuth velocity degrees sec 20 Azimuth resolution degrees 1 C Sector Blanking 1 C Sector Blanking 2 Fig 3 7 Scan Mode Tab 3 1 Range Range step association RES 90 m RES 150 m RES 300 m RES 450 m TENG Range 36 km Range 72 Km Range 108 Ki In the PPI section see Fig 3 8 it is possible to enable different Elevation Steps together with the related parameters and set the Azimuth Velocity azimuth rotation speed with which it is intended to carry out the procedure The Azimuth resolution field determinates the antenna lobe width that allows to set the acquisition samples azimuth oversampling The Sector Blanking 1 and the Sector Blanking 2 check boxes allow choosing if to turn off the radar radiation in one or max two sectors For each sector after flagging the check box it is necessary to set the start angle of the sector blanking and the end one expressed in degrees the difference between the two values is the sector width The sector width value must result 180 degrees and in case of both sectors flagged these must be separated by at leas 10 degrees otherwise an error message will appear By means of the Max EIl field available for each sector it is possible to insert the value expressed in degrees related to the elevation angle over which the blanking will be applied no more In the RHI section that is not enabled for WR10X CE configuration it
102. nates of the radar site respectively in the decimal degrees and degrees minutes and seconds formats The RANGE control allows to specify through the proper text box the range of the Background Map to generate expressed in Km The OFFSET CONTROL allows to correct possible georeferentiation errors in the Background Map preview to generate applying to the map centre the offsets specified in the proper text boxes along x and y axes offset expressed in pixel Only after having configured all the parameters necessary to the generation of the Background Map the interface makes available the DRAW button Clicking on the DRAW button a map preview generation algorithm is activated at the end of which the map will be displayed in the proper preview window The following figure shows this situation BACKGROUND MAP CREATOR ie kab Sere Haine C Documents and Settingslat ELDES DocumentiProva PNG LI Deg mode LAT Radar LON Radar Dms mode LAT Radar LON Radar Range Offset control X Offset Georeferentiation file DiR chgroundMaoCreatonBackgroundMapCreator_menCartografia_ltalia FIND image Dimension Georeferentiation file 1024 Georeferenziazione Tav ifalia Out txt image Type Georef data conversion file DIR Truecolor chgroundMapCreator BackgroundMapCreator_menCartografia_lfalia Georef data conversion file Tav tala Out affine txt Fig 5 38 Map Creator Preview ELDES Document code Page 100 of 1
103. ndicates that the section will automatically disappear The width of the side sections sizes can be modified putting the cursor over their edge they can also be placed anywhere in the main window or it is possible to leave them floating in any area of the screen all this is possible holding the left mouse button on the title bar of the section and dragging it in the desired area The whole window can be resized and if necessary expanded to full screen f Work mode Automatic selection Show the last 50 images Last date selection From 27102 2010 i j Interval date selection From 06 07 2010 06 07 2010 i Manual selection I From 04 04 2010 to 04 04 2010 En Path gt ESM wr t0xyarchive D WR 10x Evento_2010_04 Map settings Iv Background i Radar Image i Iv Nations i M Regions Iv Provinces 2 Municipalities Ka Default Mark i Iv Cities Citiesatown l Rivers GIF BMP PNG TIFF Products filter Range Without clutter 72 Km lw with clutter Not Used Ta ooo BE Fig 5 2 Sections manual resize The Radars and Products section shows the list of products which have been configured in the system only relating to the PC controlled radar Server version allows to display only products related to the l
104. ndicator Fig 3 23 Products As regards the General Configuration it is possible to put a flag on one or all of the following options e Show GestObjTsk video log shows in the window which is opened at any scheduled scan request all messages related to the operations which the involved module is carrying out e Save GestObjTsk log on file GestObjTsk log saves the same information on a text file named GestObjTskyyyymm log yyyy year mm month in the WR 10X Bin LogFiles folder e Show GestObjTsk window allows to show the GestObjTsk application window If this is not displayed the log display too will be missing e Show elaboration details displays information related to the generation of each single product controlled by the GestObjTsk father module lt is also possible to choose the format of the date to be displayed in the product which is going to be generated between Local Time or UTC Document code ELDES OM 11242 10 01 Proprietary Information Page 41 of 118 EP DES van User Manual Server The Products section shows the list of all registered products included in the system together with the related characteristics For WR10X CE configuration the product RHI is not enabled Putting a flag on the Enable column it will be possible to decide which products the system has to generate while clicking on the Configure button it will be possible to have access to the configuration typical of each single product Fur
105. oblem has occurred or occurs The log is Monthly type IE DataAcqTsk201202 log Blocco note File Modifica Formato Visualizza 700 700 700 O1 702 703 703 703 704 704 O7 710 710 7 10 11 11 11 212 31 41 F1 41 aK e 32 42 51 ala e et ie ie Ye ake W ae a Yale 53 12 212 size 12 13 213 13 nf Fb 47 32 33 Stopping antenna rotation de 245 I a7 16 02 2012 16 02 2012 16 02 2012 16 02 2012 16 02 2012 16 02 2012 16 02 2012 16 02 2012 16 02 2012 16 02 2012 16 02 2012 16 02 2012 16 02 2012 16 02 2012 16 02 2012 16 02 2012 16 02 2012 16 02 2012 16 02 2012 16 02 2012 16 02 2012 16 02 2012 16 02 2012 16 02 2012 16 02 2012 16 02 2012 16 02 2012 16 02 2012 16 02 2012 16 02 2012 16 02 2012 16 02 2012 16 02 2012 16 02 2012 16 02 2012 16 02 2012 16 02 2012 16 02 2012 16 02 2012 16 02 2012 16 02 2012 16 02 2012 16 02 2012 16 02 2012 16 02 2012 16 02 2012 16 02 2012 4 lol x S2eeee220222 Start data acquisition process 2 s222 Start management of the scan l scan belonging to the lt Default_Radar gt radar Initialization commands serial port Stopping data trasmission Returning antenna to the Home position Setting azimuth velocity 20 setting cells value 120 Setting range step value 300 000000 Setting tune indicator threshold 100 Starting radiation Starting tuning
106. ocal radar while the Client version allows to display products related to different radars and composite products The Settings section is composed of the following sub sections e Work mode e Map settings e Products filter described in the following paragraphs ELDES Document code Page 78 of 118 Proprietary Information OM 11242 10 01 EP DES WR 10X User Manual Server 5 1 Work mode The Work mode section allows to select and set one of the four possible display mode related to radar images e Automatic selection allows to set a number of frames to be sequentially displayed within 1 and 50 To set the number of frames click with the mouse on the bar and drag it until the desired number is displayed in the related box Frames are selected in order to show one after another a buffer of the last n images dynamically updated each time a new image is produced by the system and saved in the DataFiles folder Work mode Automatic selection Show the last images a YET ko AAA Fig 5 3 Automatic selection e Last date selection allows to select a date from which all images available in the DataFiles folder are displayed one after another To select the date it is possible to manually enter it in the From field or it is sufficient to click on the arrow it will appear a calendar from which it will be possible to make the selection Clicking on Today the current date will be automatically entered while clicking on Clea
107. on step 1 1 5 Azimuth step 1 0 ki i a 2 Elevation step 2 th step 2 Elevation step 3 4 5 mI a Azimuth step 3 Elevation step 4 m P Azimuth step 4 Elevation step 5 O Azimuth step 5 Elevation step 6 O Azimuth step 6 Elevation step 7 r AZIMIL J Elevation step 8 th step 7 Elevation step 9 Azimuth step 8 Elevation step 10 Azimuth step 9 O Azimuth step 10 Azimuth velocity degrees sec 20 l l Elevation start a Azimuth resolution degrees l Elevation stop 0 Sector Blanking 1 Sector Blanking 2 Automatic RHI a Max El Max El Min t Max t E Si ki Bright band detection Elevation resolution decidegrees 3 Fig 3 8 Azimuth and elevation steps ELDES Document code Page 28 of 118 Proprietary Information OM 11242 10 01 EP DES WR 10X User Manual Server 3 1 3 Scan Setting The Scan Setting folder is composed of a left and a right block Settings PPI IC Do not radiate Clutter filters L Radiation off at end scan tuning Enable declutter statistical Filter C Save raw data in r file C Enable clutter map Clutter map update E Save raw data in text file 6 Low threshold Tuning 7 High threshold After Before None f 0 Recovery windows dimension i Enable Pointing for Tune Settings Azimuth direction Drag a column header here to group by that column Enable IR Decision Threshold Height Threshold Range 4 Range Step A IR threshold gt
108. oned rule are described below e Enable action rule on products files applies the specified rule on all product files having the Enable column enabled e Enable action rule on text raw files applies the specified rule on all RAW data files in text format e Enable action rule on Z files applies the specified rule on all binary files called Z related to products having the Enable column enabled e Enable action rule on scan files applies the specified rule on all Scan type files including information about the scan through which the related product has been or will be generated e Enable action rule on raw files applies the specified rule on all RAW files in binary format General configuration Acton Archive configuration fa a Archive configuration Drag a column header here to group by that column Enable Name Description Level r RHI Range Height Indicator First Level V Enable action rule on products files Enable action rule on text raw files Enable action rule on Z files C Enable action rule on scan files Enable action rule on raw files prreeeseeeeeesceececesesosssssseseseeeeeececeeesesssssseseeeeesesesseseesssssssseesesesesessssssesssy pa a Fig 3 37 Archive configuration ELDES Document code Page 64 of 118 Proprietary Information OM 11242 10 01 vann EDES User Manual Server All archived files are placed in the Archive sub folder belonging to the WR 10X installation
109. ormat no image will be displayed Lest date selechon interval dole sek chon Maral selecton 7 iia oo DAWA 1QXi vento 2010 04 04 Fig 5 7 Map settings ELDES Document code OM 11242 10 01 Proprietary Information Page 81 of 118 EP DES van User Manual Server 5 2 1 Layers management In the Map Settings section it is possible to manage layer in a dynamic and flexible manner All functions necessary to make maximum use of the graphic support are described in the following paragraphs Map settings Default Background i Default Mark Radar Image Fig 5 8 Layers management All configured layers are included in the list Note Each product of each radar has specific layers Through the and buttons it is possible to move the selected layer upwards or downwards The lower layer is the layer which will be positioned over any other image while the first will be the layer which will be under all subsequent images The button allows to remove the selected layer ELDES Document code Page 82 of 118 Proprietary Information OM 11242 10 01 vann EDES User Manual Server To add a new layer it will be sufficient to push the button A window in which it will be possible to enter all the necessary information will appear as shown in the following figure ES Manage Layer Layer properies Laver Mame Transparence C Laver paths Save Cancel Fig 5 9 Layer
110. ot be included inside any set sector blanking Enable IR for the first installation the check box must be not flagged Only if a radar to radar interference is present this option can be eventually used Note The Enable IR check box flagged action is equivalent to set IntReject 3 in the WR 10X Bin SignalProcessingConstructor xml file and in this case this part of xml file is ignored IR threshold after flagging the related check box it is necessary to insert the IR threshold value 0 100 dB in the proper field A a y 4 Note The Enable IR check box flagged action is equivalent to set IntReject 3 in the WR 10X Bin SignalProcessingConstructor xml file and in this case this part of xml file is ignored The above mentioned choices are not mutually exclusive more than one setting can be set except for the Tuning parameters 3 1 3 2 Scan Setting right block The right block divided between PPI and RHI contains the Clutter filters an Settings sections The RHI section is not enabled for WR10X CE configuration On Clutter filters it s possible to set parameters necessary for the clutter filter configuration as follows e Enable declutter statistical filter it enables the statistical declutter filter e Enable clutter map PPI only it allows to use the clutter maps if present for the declutter algorithm e Clutter map update PPI only during the radar operation it allows
111. ove described for RAW data the azimuth and elevation positions are not involved by the offset In particular the elevation position of each ray expressed in decidegrees shows the angle to which the ray closes ELDES Document code Page 54 of 118 Proprietary Information OM 11242 10 01 vann EDES User Manual Server With reference to the example mentioned above RHI A00 201112011256 B 0360 0150 0005 2800 U z with RHI start elevation angle 0 and RHI stop elevation angle 30 if we also consider the header presence on each ray the integrated data matrix for this RHI scan has a size of 60x263 N 30 0 0 5 The z binary file related to RHI integrated data is saved in a ushort format Unsigned Integer 16 bits The z binary file related to RHI integrated data is available only for radar WR 10X full version 3 3 General The General folder includes general configuration parameters YO DataAcg Data acquisition and signal processing manager 5 x p General configuration V Show DataAcqTsk video log ID Show signal process details W Save DataAcqTsk log on file DataAcqTsk log IV Display window application C Save advanced analisys log on file C Advanced work mode RS232 radar command configuration COM port Baudrate Parity Data bit Stop bit 1 9600 rv Odd 7 118 1 Save and Exit Save T i Save profile Load profile Fig 3 28 General folder The Genera
112. pe oi de not kek e 21 2 DATA ACQUISITION AND SIGNAL PROCESSING SETTING cccecceccecceeceseeseeseueeeseueeueeueeueeueeueeaeeeeueeans 22 3 1 Ne ti tered aie kra b me v od kan E ie E at dol T ab atant ek an e S ont bab k m e anfin tt padi aie 23 311 FRAC A SOA Listessi ata onde it de istil kre fa on n tn ekite an pase EEE REENE 23 ele ON NOU Cette be pe ae anan ako a ik e bek al ke ea p Se kai One de e bo Ske Seba ek ae eat Ok 25 Aw prc D S N boat ede it ak ee ro ee nee td ne en ke e into ka 29 3 1 3 1 SO mT WET DIOC f b ai a t la n E a kk e be mo kis osi le 29 3 1 3 2 Scan Seting right DIGCK sesir ein Rae aE EEE REA 30 314 PINT ANON ae otis otanjes kiye soti to fin tto p t cers aE see ETE DEERE EEEO ETENA EN 34 JAN CS CEG a datt E E ta l e in EE EA e ase e al A EA 36 MOS acca ce aie ss plom sot kisak is de l ibon ja palem ao kes ante in b l kipa y m pon been dad kim kn ie pd man tat tee 40 3 1 7 Advanced work NOU Oo e ls a in ti l ti yan n ki aa tn e a en e n ae a n 5 e a a n l l lat e kn 42 3 2 SIGNAL PROCE rt pei tea va tit w in lt pe on tap fk a a e n kk la a e pase krak e AP pen e bak a n ie 43 321 SIACUN ON RAW ANA elites ie bain tk td lay n e oe e a AE an e tp ak a e n a pv te e a l e e b 47 3 2 2 Structure of PPI integrated data ccccccccsseeecccceeeseeeeeeceeeeseaeseeeeeeeeeeaeeseeeeeeesseaeaseeeeeeesssaeaeess 49 3 2 3 Structure of RHI integrated data cccccccssessecccceeseeeseseceeceseeeesseeeeeeeessa
113. r gt Seh Customize Open Save 6 Print PPGAFHORERS Print Page Setup Scale gt Hand Tool Magnifier Zoom Out Zoom 100 le Zoom In A j First Page Previous Page Next Page Last Page Multiple Pages Color gt S amp E Watermark Export Document gt E Send via E Mail gt e 8 1 1G OR i Exit Reset Toolbar b y HEF a i San Giovani a pe 7 R Certaldo F Valdi Pesa 7 A vite J Vaideing r 3 p Q Fig 5 32 Toolbar customization ELDES Document code Page 96 of 118 Proprietary Information OM 11242 10 01 EP DES WR 10X User Manual Server The meaning of all icons which can be displayed are shortly described in the following figure S AO TE Multiple Pages Export Document Print sy Dispiay Exit Zoom ki i mam Color L FB amp amp Iv ak ko w Grad O T Watermark Send via e mail Print Page ki isi Setup Fig 5 33 Toolbar icons The Search icon allows to open the Find window in which it is possible to enter a text to be searched in the document Find what Search Options L Match case L Match whole word Search up Ready Fig 5 34 Find The hand tool allows to move the document dragging and dropping it For all other buttons refer to the above described menus 5 5 2 View Selecting View from the menu bar the following entri
114. r 000 00000 Deg LON Radar 000 00000 Deg Range 36 00 Km The LAYER SELECTION section allows to define the layers types to generate previews or images The following choices are available DEM Data this layer represents through a color scale which can be set by the user the altimetry of the involved geographic area Nations Bound this layer represents the boundaries of nations included in the involved geographical area Regions Bound this layer represents the boundaries of regions included in the involved geographical area Provinces Bound this layer represents the boundaries of provinces included in the involved geographical area Municipalities Bound this layer represents the boundaries of municipalities included in the involved geographical area Cities this layer represents the main cities included in the involved geographical area thresholded according to a configurable inhabitants number Rivers this layer represents the main rivers included in the involved geographical area All Layer this option disables all other options and imposes the generation in preview mode of all seven layers described above for the involved geographical area Layer Selection DEM Data LI Cities L Nations Bound LI Rivers L Regions Bound L Provinces Bound O Municip Bound LI Ail Layers Roads and Rails options cannot be selected and are pre settings for future updates The GEOREF CONTROL section allows to specify the path including the a
115. r the field will be removed Last date selection From Mkio 20os O nten Cl ottobre P 4 2008 Inm q w s d From za aW 2 3 4 5 6 7 8 9 10 ii 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 Map settings af 20 29 30 31 1 2 ii Default 3 4 5 6 7 8 Q Defaut Today Clear Fig 5 4 Last date selection ELDES Document code OM 11242 10 01 Proprietary Information Page 79 of 118 EP DES van User Manual Server e Interval date selection allows to select a couple of Date hour in which all images available in the DataFiles folder will be selected The date choice is similar to that related to the Last date selection above mentioned Hour must be manually entered 8 Interval date selection From 27 11 2008 B131 ta 27 11 2008 4 4 novembre kt 008 k II lmm qw sd Mapsettings 27 28 29 30 31 1 2 e Default 43 6 7 BOY G Defaut 10 11 12 13 14 15 l 17 16 19 20 21 22 23 Radar I 24 25 26i 26 29 30 iL 34567 Today Clear Fig 5 5 Interval date selection e Manual selection allows to specify a series of customized paths in which it will be possible to find the products images to display The path of the Archive folder is set by default without the possibility to be removed or changed From here it is possible to display all data which have been archived in the system Clicking the right mouse button with the pointer inside the
116. raphic product files Z files binary type SCAN files RAW files both r and txt The BIN folder is structured as follows di BackgroundCartography 31 12 2011 16 04 Cartella di file 31 12 2011 16 04 Ji cmap 17 02 2012 16 38 Cartella di file 17 02 2012 16 38 di Colortbl 17 02 2012 16 11 Cartella di file 31 12 2011 16 04 LogFiles 31 12 2011 16 04 Cartella di file 31 12 2011 16 04 obj 17 02 2012 16 11 Cartella di file 31 12 2011 16 04 di ThresholdDef 17 02 2012 16 38 Cartella di file 17 02 2012 16 38 jae BackgroundMapCreator exe 09 12 2011 14 50 Applicazione 2 988 KE 09 12 2011 14 50 E CABARC EXE 20 03 1997 07 01 Applicazione 112KB 20 03 1997 07 01 e DataAcg exe 11 01 2012 17 11 Applicazione 476 KB 11 01 2012 17 11 DataAcg xml 17 02 2012 16 32 Documento XML BKB 04 02 2012 22 54 EA DataAcqTsk exe 11 01 2012 17 12 Applicazione 118KB 11 01 2012 17 12 M DataArchiveTsk exe 11 01 2012 17 13 Applicazione 82KB 11 01 2012 17 13 A DataView exe 11 01 2012 17 15 Applicazione 464KB 11 01 2012 17 15 Fig 4 3 Folders structure Inside the LogFiles folder it is possible to display ALL the LOG files described in the previous chapters ELDES Document code OM 11242 10 01 Page 76 of 118 Proprietary Information WR 10X User Manual Server 5 Display The DataView software package allows to display data EP DES A To launch the software click on DataView link icon created on the desktop or select from the menu S
117. rchive of geographical information used by the application for layers generation The default path is the following D WR 10X Bin CARTOGRAPHY Once all controls necessary for the layers generation have been configured the application makes the DRAW button available ELDES Document code Page 104 of 118 Proprietary Information OM 11242 10 01 vann EDES User Manual Server The following figure shows a map displayed in preview mode in the interface graphic window VIEWER UTILITY O Mosaic radar mode MIN LAT MAX LAT MIN LON MAX LON Single radar mode LAT Radar LON Radar Range 42 3529 43 6471 10 1058 11 8942 43 00000 11 00000 72 00 Layer Selection DEM Data Cities Nations Bound O Rivers image Type e Dimension Regions Bound Roads Truecolor O Provinces Bound Rails O Municip Bound O Ali Layers Georef control Geodata file DIR DAWR TOMBINNCARTOGRAPHY FIND Fig 5 43 Layer Creator Preview When the preview image is available in the interface graphic window also the IMAGE TYPE and IMAGE DIMENSION controls as well as the SAVE button are enabled The IMAGE TYPE control allows to select the type of color of images which can be saved in the different layers from those displayed in the interface graphic window The possible choices are TRUECOLOR and GRAYSCALE The IMAGE DIMEN
118. ry it will be copied in the WR 10X Bin Colortbl in which the system places the color table of the registered products 2 Manage layer enables or disables the possibility to manage the Map settings section in the DataView application see par 3 Manage clutter filter enables or disables the possibility to manage the Products Filter section in the DataView application see par 5 5 3 4 Variable label indicates the description to be displayed in the drop down menu below the Range parameter in the Products Filter section related to DataView application The value included in this field is the informative content of the product file portion shown in the following example PPI A01 200810271340 B 0360 0010 U PNG In the specific case of a PPI product it represents the elevation expressed in tenths of degrees 5 Tooltip indicates the description to superimpose on the image simultaneously with the left mouse button click In this description it is possible to use letters numbers mathematical expressions and MACROS which can be represented through a specific syntax For a detailed description on syntax and MACROS use refer to par 3 5 4 3 5 4 Tooltip Syntax and MACRO MACROS consist in key words corresponding to system variables numbers or mathematical expressions which can be used alone or in more complex formulae The list of MACROS available in the system and a short description of their functions are shown below SORTI
119. s Distance 7 604 76 Km Height 5 52556 Km Azimuth 33 6961 7 Elevation 50 00000 Reflectivity 30 lt gt 32 dBz Fig 3 42 Tooltip ELDES Document code OM 11242 10 01 Proprietary Information Page 71 of 118 EP DES anan User Manual Server 3 6 DataAcq buttons description The following buttons appear under the DataAcq window e Save and Exit saves the changing done and closes the application e Save saves the changing done e Exit closes the application e Save profile saves the configuration profile displayed at that moment in a file having a wpf extension and whose name is specified by the user e Load profile loads the profile from a wpf file specified by the user replacing it to the configuration displayed at that moment e Start selected scan immediately starts the running of the active scan Save and Exit Save Exit p gave profile au Load profile Start selected scan Fig 3 43 DataAcq buttons Note Start selected scan appears only if the Scan window is selected ELDES Document code Page 72 of 118 Proprietary Information OM 11242 10 01 vann EDES User Manual Server 3 7 Color scale The color scale used by each product is specified through a proper configuration file available in WR 10X Bin Colortbl and called colortbl product acronym gt txt in which lt product acronym gt is an abbreviation composed of three letters indicating a specifi
120. s the application configuration before proceeding with the layer generation The following figure shows the application configuration interface VIEWER UTILITY Layer Map Name LI Mosaic radar mode MIN LAT MAX LAT MIN LON MAX LON Single radar mode LAT Radar 000 00000 LON Radar 000 00000 Range 36 00 Layer Selection VI DEM Data LI Cities LI Nations Bound L Rivers O Regions Bound Provinces Bound O Municip Bound O Ali Layers Georef control EXIT Geodata file DIR DAWR 10ABINCARTOGRAPHYA FIND Fig 5 42 Layer Creator Preview From the application configuration interface it is possible to generate georeferenced layers for the single radar or for the mosaic of several radars Two proper sections allow to specify the necessary parameters in both cases In case of mosaic of several radars it is necessary to specify four parameters related to the minimum latitudes and longitudes and to the maximum latitudes and longitudes of the geographical area covered by the mosaic In case of single radar it is necessary to specify three parameters related to the latitude and longitude of the radar site and to the range expressed in Km for which the layers generation is required Document code ELDES OM 11242 10 01 Proprietary Information Page 103 of 118 EP DES anan User Manual Server O Mosaic radar mode MIN LAT YYYY Deg MAX LAT Deg MIN LON Deg MAX LON Deg Single radar mode LAT Rada
121. singConstructor xml This group of functions can be set by the WR 10X Bin SignalProcessingConsitructor xml file modification the default file configuration is reported in the following lt xml version 1 0 gt lt InterferentRejection IntReject 0 DimFilter 3 LevelRejectThr 30 gt lt InterferentRejection gt lt ClutterMapMedianFilter CMAPMedFilt 0 CMAPDimFilter 3 gt lt ClutterMapMedianFilter gt lt PPIMediankFilter PPIMedFilt 0 PPIDimFilter 3 gt lt PPIMedianFilter gt lt RHIMedianFilter RHIMedFilt 0 RHIDimFilter 3 gt lt RHIMedianFilter gt lt NoiseDataCollection SaveNoiseData 0 gt lt NoisebdataCollection gt All the parameters meanings are explained in the following 8 1 1 Interferent Rejection This section allows to enable and to set a filtering mode against interfering signals Four modes are available by means of the IntReject parameter setting IntReject 0 no one filter is applied IntReject 1 one dimensional MedianFilter applied on Azimuth axis related to RAW data In this case both the DimFilter and LevelRejectThr parameters are necessary in order to respectively define e dimension of the one dimensional mask used in the filtering e threshold in levels under which the filtering process will not apply The filter is locally applied only for range gate for which the MedianFilter application introduces a level reduction greater or equal to LevelRejectT
122. ssibility to set the password through the Set password button will be enabled in this way the scheduled task will be run even if the login to the system is missing TSK Default_Radar Scan 0 Operazione Pianificazione Impostazioni E CAWINDOWSAT askai TSK Default Radar Scan fek Impostazione password Password Conferma password Esegui come ELD ES w Ox Imposta password Esegui solo ad accesso effettuato i Attivata l operazione pianificata viene eseguita all ora specificata OF Annulla Fig 3 16 Enter Password ELDES Document code OM 11242 10 01 Proprietary Information Page 37 of 118 EP DES anan User Manual Server Clicking on Scheduling folder and holding the New button the window shown in the following figure will appear TSK Scan 0 Operazione Pianificazione Impostazioni f1 alle 9 00 ogni giorno dal 02 04 2008 ye Elimina Pianifica operazione Ora di avvio Ogni giorno vi 9 00 Avanzate Pianificazione giornaliera Ogni H glomo i lv Mostra pianificazioni multiple OK Annulla Fig 3 17 Scheduling Clicking the New button an item will be added to the scheduling list Operazione Pianificazione Impostazioni f1 alle 9 00 ogni giomo dal 28 11 2008 1 alle 9 00 ogni giorno dal 28 11 2008 Fig 3 18 Scheduling addition Clicking on the Remove button the selected scheduling will be removed From the drop dow
123. st start up of the display software it will be necessary to configure the controls reset In order to accomplish this it will be necessary to click with the right mouse button on the menu bar at the right top side of the DataView window in order to make the Customize control available T Li Date 04 04 2010 n Ti me 43 36 CE STI j Automatic selection F Last date selection P H i L H r i z i HE i Interval date selection z 8 b JE i The Customize control gives a proper configuration window in which also the Options tab is available and from which it is possible to have access to the Reset my usage data button Customization Toolbars Commands Options Personalized Menus and Toolbars _ Always show full menus Show Full menus after a short delay Reset my usage data Other Large icons Show ScreenTips on toolbars Show shortcut keys in ScreenTips Menu animations System default Close Clicking on this button controls available in the menus included in the DataView control bar take the installation settings This operation is absolutely necessary if during the installation a preexisting installation update has been configured ELDES Document code Page 88 of 118 Proprietary Information OM 11242 10 01 amann EP DES User Manual Server 5 5 1 File Selecting File from the menu bar two choices are available e Exit to exit from the viewer e Image management
124. t has been put a flag on the Show Screen Tips on toolbar option holding the mouse pointed on a menu bar icon a message showing the function related to the icon will appear 3 K E Aa Page Setup Page Setup Fig 5 27 Icons description Finally clicking on Menu animations it is possible to choose how to animate drop down menus appearing in the Preview window Possible choices are shown in the following figure Menu animations Slide R System default None Fade Unfold Random Fig 5 28 Menu Animations ELDES Document code Page 94 of 118 Proprietary Information OM 11242 10 01 vann EP DES User Manual Server Background From the Background menu it is possible to select the image background color selecting Color Background F a Color ko snus ii System a Watermark I ret Toth Fig 5 29 Background lt is possible to choose the color among three different groups Custom Web System selecting Watermark entry it is possible to make a writing Text Watermark folder and or an image Picture Watermark folder appear on the background Different options for the image text customization are available for each folder Watermark Text Watermark Picture Watermark Text SAMPLE Direction ForwardDiagona
125. tart WR 10X DataView Once the program has been launched the Fig 5 1 will appear A Note End loop delay sec Work mode Automatic selection Show the last 15 images Ka Last date selection From 27jG2 2010 Interval date selection From 06 07 2010 l sil to 06 07 2010 Manual selection From 04 04 2010 mi to osjosjzoi0 ks Enable Path gt DI p twa 10xtarchive Map settings iv Background L Default Mark Iv Radar Image iv Nations iv Regions Iv Provinces Cities _ Cities amp Town L Rivers DAWR 10X Evento_2010_04_04 GIF BMP PNG TIFF Products filter Range Without clutter 72 Km With clutter Elevazione 10 0000 le RA l d Fig 5 1 DataView Main screen The chapter describes the application for the WR 10X full configuration for the WR 10X CE the RHI product is not displayed Document code OM 11242 10 01 Proprietary Information Page 77 of 118 EP DES WR 10X User Manual Server The Radars and Products and Settings side sections can be set in order to automatically disappear when they are not used or they can be blocked in order to have them always available The a button turned down indicates that the section is blocked the E button turned left i
126. tart and End points according to the real antenna speed calculating the number of pulses actually integrated in each cell Ray date Ray timestamp Ray progressive number Ray azimuth position Ray elevation position 221 35 29 222 141 173 221 111 114 62 62 54 80 66 86 84 124 83 221 35 31 222 142 173 220 113 115 71 66 48 83 63 85 82 124 83 221 35 20 225 139 172 220 117 115 72 65 60 71 59 87 82 123 81 221 35 33 222 137 172 221 118 112 65 66 69 90 59 85 84 123 80 121 111 78 3 7 222 35 30 221 135 170 221 120 111 73 63 75 93 60 86 81 121 82 222 35 35 223 134 170 220 122 110 64 64 76 80 57 85 80 121 79 222 35 31 222 134 169 224 122 111 61 69 67 90 56 87 76 120 81 20111201 130012527 222 35 24 222 133 169 221 121 115 63 66 63 80 59 85 79 119 81 20111201 130012527 222 35 27 222 133 170 221 121 114 72 66 50 91 61 85 75 119 79 20111201 130012527 10 222 35 24 222 131 168 222 122 111 70 62 37 84 56 86 75 119 78 20111201 130012527 11 223 35 38 224 131 167 223 120 110 71 70 55 90 56 86 72 118 80 20111201 130012527 12 223 35 33 221 130 166 221 120 106 65 66 68 80 58 86 74 117 80 20111201 130012527 13 223 35 28 224 131 167 222 119 107 56 71 69 96 59 86 69 116 79 20111201 130012527 14 223 35 27 221 131 165 222 121 109 74 68 68 88 58 87 70 116 78 20111201 130012527 15 223 35 35 223 132 165 223 121 112 79 70 71 104 56 85 68 116 7S 20111201 130012527 16 223 35 26 222 132 164 222 123 114 70 69 75 92 58 86 71 115 78 20111201 130012527 17 223 35 31 224 134 164
127. te E Documenti SE Pw a Musica Ed video ME Computer 5 Disco locale C g Dat D Sy HP_TOOLS E Fig 2 19 License File selection select the folder of the license file select the lic file and press Open Confirm to save the license data by pressing Si on the Fig 2 20 x Do you want to save license data ee ee Fig 2 20 LicSrvUI saving The user will see the License Server Control Center window Fig 2 15 updated with the correct configuration ELDES Document code Page 20 of 118 Proprietary Information OM 11242 10 01 vann EDES User Manual Server 2 2 3 Start applications After completing the software installation the PC desktop will be populated by the link icons to the three software applications The icons are described in Tab 2 2 Clicking on the link the related software will be launched Tab 2 2 Software application icons DataAcq icon it launches the DataAcq application in order to set up the radar configuration DataView icon it launches the DataView application in order to display radar data RCU TS icon it launches the RCU TS application in order to perform system debug for installation and maintenance procedures not object of this manual Similarly it will be possible to launch the installed software from the menu Start All Programs WR 10X di Microsoft Visual Studio 2010 Express Computer di Orade VM VirtualBox PDF Complete Rete di
128. the InstallShield Wizard for License Server The InstallShield Wizard will install License Server on your computer To continue click Next lt Back Cancel Fig 2 8 License Server InstallShield Wizard Press Next gt to continue ELDES Document code Page 14 of 118 Proprietary Information OM 11242 10 01 User Manual Server On the Fig 2 9 select the installation path and press Next gt License Se rver InstallShield Wizard Choose Destination Location Select folder where setup will install files etal Shield Fig 2 9 License Server InstallShield Wizard Path ELDES Document code OM 11242 10 01 Proprietary Information Page 15 of 118 EP DES van User Manual Server On the Fig 2 10 press Install License Server InstallShield Wizard Ready to Install the Program The wizard i ready to begin installation Click Install ta begin the installation IF pou want to review or change any of pour installation settings click Back Click Cancel to exit the wizard Installshield Back Cancel Fig 2 10 License Server InstallShield Wizard Ready The Fig 2 11 asks for the License Server Service installation press the Si button to confirm a po Fig 2 11 License Server InstallShield Wizard Question ELDES Document code Page 16 of 118 Proprietary Information OM 11242 10 01 vann EP DES User Manual Server At the end of the installation the Fig 2 12 is shown
129. ther details will be available in the specific manuals 3 1 7 Advanced work mode Only if in the General configuration section the Advanced work mode check box is flagged the Advanced work mode is available this is a special configuration window protected by Password used only during the start up procedure in order to determine the optimum thresholas for the declutter algorithm and to enable specific operating modes useful to the installer The Advanced work mode window is shown in Fig 3 24 Scan made Scan setting Communication cele Advanced work mode Scan Mode i Acquisition without angle check read 1000 beam gt Acquisition with software angle simulator E Creating clutter maps i Read RAW data From file Data file For TEST mode Number of maps to create Clutter Map Fig 3 24 Advanced work mode ELDES Document code Page 42 of 118 Proprietary Information OM 11242 10 01 EP DES WR 10X User Manual Server 3 2 Signal Process The Signal Process folder includes parameters related to the signal processing and it is divided into Radar calibration and Radar setting on N DataAcq Data acquisition and signal processing manager MDS dB Trasmitted power KW Antenna gain d8 Azimuth beamwidth degrees Elevation beanmicdth degrees Trasmitted frequency MHz Radome attenuation dB Reflectivity constant Medium Long PRF H2 Pulse time us 182163 091
130. timation by getting Pulse number pulses and creates a Noise Mean Level in the log file this value that depends on the temperature is used to calculate the real offset of the radar receiver characteristic the Noise calculation indicates when the processor has to collect data for the noise estimation At the end is suggested in order to not disturb the tuning phase The Tune indicator threshold determinates the value for which it is done a complete or a fast tuning Typical value is 100 Enable noise filter Enable noise filter Manual Automatic E Manual Automatic 20 Noise level 20 Noise level 1 Log threshold 1 Log threshold 1200 Pulse number Pulse number Noise calculation Noise calculation At the beginning At the end A Never 0 Tune indicator threshold 0 Tune indicator threshold Fig 3 26 Enable noise filter section ELDES Document code Page 46 of 118 Proprietary Information OM 11242 10 01 vann EDES User Manual Server 3 2 1 Structure of RAW data As it has already been said it is possible to extract data related to scans which have not been processed in order to use them in next processing lt is also possible to obtain data which have not been processed directly in a text file readable by whatever editor The purpose of this paragraph is to describe the structure of the RAW file also called raw data file not processed The file is shown in the following figure The first column show the really
131. tk kak l kat as al kk ta a ka a kk aa nnne 76 5 1 DATAVIEW MAIN SCREEN l kk tt kb tt kt bwaw kaka kaa aaa aaa taa aaa aaa aaa eaaesaesaesaesassseseeseesoasoesoasonsoesoessnosnoannn TI 5 2 SECTIONS MANUAL RESIZE 2 2c0cceceececeececeececeececeeaeceeaecuenececaececeececueaeceeaeseeeseseesecueaesueaeentaeaes 78 5 3 AUTOMATIC SELECTION swit t mitot f is tdt tt ata ati tt atan ont eta kt kak a na st ta a a a kk taa n ak ek as nnna 79 5 A LAST DATE ELECTION kitte kre ranerne fear Ae e Sit oak pin kol para Aka ta ro k eee po tetas 79 5 5 INTERVAL DATE SELECTION e 00050 qokitib aivaat fianod minn wait gn kt kl e B ke e n aki l a a kl pk RA k 80 5 6 MANUAL SELECTION kb tt tt tt kt ka kaka kaka kaka aa aaa aa na PR irai Pe A adira ER p akn Edna Eina ara ERNE ana PR RERE 80 5 7 MAP SETTINGS wxsatetermdecos bade eeina i Ee ae e er S ai deen Din kali EE RERE EERE RAEE sinis ea p met 81 5 8 LAYERS MANAGEMENT 2 2ccececcececcececeececeececeececeececeeaeceeaececaeaeseeaecueaeceeaeseeaeseeneseseeaesueaeentaeaes 82 5 9 LAYER ADDITION CHANGE 2 ccceececcecceceececcecaeceeceececaecueceeaeceeceeaeeaececueseeaecueceeaesneseeseeaesneeneaes 83 5 10 LAYER PREVIEW cccccccsccscceccsceecceccesssccuscescanccuccuccuccuvcucossoucoureuseersuenatsusnsdsaueauscntcusenecnvonsess 84 5 11 PRODUCTS FILTER first yo on n tv ti ae a n t e e ko ne a e e e e oi e n ae m padi 85 B 12 GONTROL BAL esisi cece ge deca etann arara i kas en een wee kinan koi petet
132. to stop the generation of clutter maps in case of weather worsening clutter maps must be acquired in clean weather condition and resume it later e Low threshold recommended values in the range 0 15 ELDES Document code Page 30 of 118 Proprietary Information OM 11242 10 01 vann EDES User Manual Server e High threshold recommended values in the range 6 30 e Recovery windows dimension allowed in the range 0 6 The Settings section is composed of the following columns e Decision Threshold decision threshold for clutter acknowledgment allowed values in the range 0 100 e Height Threshold height threshold above which the declutter is not carried out allowed values within 0 180 e Range it shows the available range radar range in distance e Range Step it shows the available range step for each range The meaning of the above mentioned parameters is described in the following paragraph Statistical declutter filter The declutter filter is a statistical type and its operating principle is based on the different distribution of samples occurring between the radar echo due to the clutter and the radar echo due to the weather signal The following paragraph gives a general explanation about the statistical declutter operation and the DataAcq setting parameters function In order to describe its operation we will base our explanation on a matter of fact each PPI cell related to the WR10X system is sampled with N val
133. to the image itself will be shown through a tooltip The displayed descriptions can be configured in the Registration section related to DataAcq application at the Tooltip entry lt is also possible to carry out a recursive zoom on the displayed image enabling the related entry in the Tools menu moving holding the left mouse button squaring the desired portion Two example figures are shown in the following ELDES Document code Page 86 of 118 Proprietary Information OM 11242 10 01 WR 10X User Manual Server W DataView a Posta in arrivo W DataView neje fm fimo s Image details Distance 24 48610 Km Height 0 21368 Km Azimuth 315 00000 Elevation 0 50000 Reflectivity 34 lt gt 36 dBz End loop delay sec 2 PPI 400 201004042136 B 0720 0050 C GIF Micro fw Manuale_Server Di IM 11242 04 doc Dataacg rata acqui Dataview Da SG n n A Document code OM 11242 10 01 banman e a pumin mnnn 505 mSec End loop delay sec PPI A00 201004042136 B 0720 0050 C GIF a x aw Manuale Server Ty OM 11242 04 doc DataAcg Data acqui Dataview Fig 5 15 Display with zoom ELDES Proprietary Information Work mode Automatic selection Show the last 15 PPCee
134. ues showing reflectivity in which N depends on the constant rotation speed of the antenna In the typical case of a 20S speed N is equal to 120 The whole PPI is composed of 14400 cells a matrix of 120x120 when the system is set on a range of 36Km while when a range of 72Km is used the matrix will be 120x240 for a total of 28800 cells Each cell as above mentioned is composed of 120 samples so each cell will have its own average value and standard deviation In its turn each PPI will be composed of a specific number of cells whose reflectivity will be due to the clutter to the weather signal or can be empty The clutter standard deviation is usually about 5 while for the weather signal it is on the average approximately 13 According to what has been said above it is clear that during observations in clear air without rain the PPI will be made almost exclusively of cells with StdDev about 5 due to clutter while all other cells will be empty except for a small percentage of cells with different StdDev lf we remove from the calculation all empty cells or those having a reflectivity lower than a threshold value it follows that a high percentage of PPI is made of clutter 90 approx The situation changes considerably as a disturbance carrying rain enter inside the PPI In this case there will be cells with StdDev due to clutter other cells will have StdDev due to weather signal and others will have a StdDev with an intermediate v
135. ve profile l Load profile Fig 3 1 DataAcq Main window The following paragraphs will describe parameters included in the folders ELDES Document code Page 22 of 118 Proprietary Information OM 11242 10 01 EP DES WR 10X User Manual Server 3 1 Scan The Scan folder is mainly composed of two sections Radars list and Scans section which include the list of all available radars and scans and Configuration folders section composed of a series of sub folders necessary to the configuration of each radar and related scans lt is important to specify that DataAcg Server version obviously see only one radar that whose scans and scheduling it manages On the contrary DataAcg Client version can see different networks composed of several radars each N DataAcg Data acquisition and signal processing manager SS Scan Signal process am Y General Radan Scan kat Sc Next Run Time A last Au taus Sipiz mz a a 5 g 3 y A mu D Uu 3 F n Ga aa Sa A ek a a c 3 lt 2 T A4 A A A 8 S 8 3 8 z 3 323 3 8 3S 8 8 8 8 oe a Li Radar and scan list Configuration folders Fig 3 2 Scan folder Note Only if in the General configuration section the Advanced work mode check box is flagged the Advanced work mode tab is available in the Configuration folders section 3 1 1 Radar Scan List This section allows to manage radars and scans the last ones

WR-10X

Contents

Download Pdf Manuals

Related Search

Related Contents