USER`S MANUAL
Contents
1. not recommended by the manufacturer may cause injuries Keep the power cord away from heat DO NOT place the induction range in on or near open flames electric burners heated ovens or other high temperature surroundings DO NOT heat any sealed cans on the induction range A heated can may explode DO NOT move the induction range while cooking or when the pan is hot After the induction range has cooled down unplug the cord and clean as follows CERAMIC PLATE wipe with damp cloth or use a mild non abrasive cleaning solution BODY wipe the control panel with soft cloth or use a mild cleaner 17 18 19 20 DO NOT use induction range for other than intended use Unplug when not in use When storing DO NOT place any objects on top of the induction range When using an induction range smooth top range for cooking keep your pacemaker 2 feet approx 60cm from the heating areas SAVE THESE INSTRUCTIONS 2 SUITABLE COOK UTENSILS FOR INDUCTION HEATING PLATES SUITABLE POTS l Iron 2 Cast iron 3 Stainless steel 4 Enamelware All pots and pans must have a magnetic bottom All pots and pans must have a flat bottom All pots and pans should have a diameter between 12cm 4 75 and 26cm 10 25 UNSUITABLE POTS 1 Pot with diameter below 5cm 2 Stainless steel pans with aluminum bottom Pottery Glass pans Bronze pans 2 3 4 5 Aluminum pans 6 7 Copper pots 8 Pans wit2. Bi 1 long BEEP Over voltage protection Bibibibi 4 short BEEP Action Try again later till electricity supply is stable Turn off immediately without any sound 1 Over heating protection or Action Try again later after the machine has cooled down 2 Surge protection Action Try again immediately Bibibibibi short BEEP last for No pan on the cook top 60seconds Bi 1 long BEEP Bi 1 long BEEP Heating empty pan on the cook top Bibibibibibibibibi 9 short BEEP Action Remove the empty pan or fill with food water as you want Bi 1 long BEEP Temperature sensor failed open or short Bibi 2 short BEEP Action Call your local distributor for service information 1 If your induction range seems to be working improperly it doesn t necessarily mean it is faulty In all cases check the preceding points 2 If you fail to identify the problem contact your after sales service center without delay Contact GSW Service Center 4151 NE Port Drive Lee s Summit MO 64064 800 458 1716
3. GSW CU 22A INDUCTION RANGE USE AND CARE INSTRUCTIONS IMPORTANT SAFEGUARDS READ ALL INSTRUCTIONS BEFORE OPERATION l 2 3 10 11 12 13 14 13 16 Use an individual 208VOLT 15 AMPERE electrical socket DO NOT block the air intake panel as blocking may overheat the unit Use pans 12cm 4 75 or larger in diameter We recommend pans be less than 26cm 10 25 in diameter Please refer to the next page for a list of suitable and unsuitable pans DO NOT touch the hot surface of the ceramic plate NOTE The induction range itself does not produce any heat during cooking however the heat from the pan will leave the surface of the ceramic hot DO NOT cook empty pots or pans Heating an empty pan will automatically activate the overheating protection device and the unit will shut off Place the induction range on a horizontal surface and at least 10cm away from the wall and other objects for proper ventilation DO NOT place any objects or tools in the air intake panel Doing so may cause electrical shock To protect against electrical shock DO NOT immerse the unit the cord or the plug in or near water or other liquids Close supervision is necessary when the induction range is used or near children DO NOT operate the induction range if it has been damaged in any manner or if the unit malfunctions Return the unit to the nearest authorized service facility for examination or repair The use of any accessories
4. air outlet SPECIFICATION Model No Voltage Vitro Ceramic Plate Electrical Power Consumption Electrical Power Range Safety Device Approvals Approvals Dimension CU 22A Induction Range 208V 50 60Hz 273mm X 273 mm 10 75 x 10 75 Max 2 200watt Approx 250watt 2 200watt Over Time Protector 2Hrs Automatic Safety Shut Off Material Compatibility Detector Small Object Detector Overheating Protection Device IC Auto Reset ETLus UL 197 ETLc CSA 22 2 No 109 FCC Part 18 ETLus ETLc FCC Part 18 328 422 100 mm 12 91 x 16 61 x 3 93 Remark The switching frequency is verified by different power setting it s to be between 20 35 K Hz TROUBLE SHOOTING feces It might be caused by No indication light when power on Cable terminal block is loose Broken circuit of fuse or automatic switch in your house Power supply stopped Heating indicator does not light in Unsuitable cooking utensil Appliance fails to heat up Utensil isn t located at the center properly Utensil is smaller than 5cm Over heating protection is activated Appliance suddenly stops heating High ambient temperature during operation Air entrance or outlet blocked Over heating protection activated ERROR CODE verified by BEEPER If the machine turned off itself please check if you can hear BEEP as following descriptions If It might be caused by
5. anel indicated 60 C 140 gt 80 C 175 gt 140 C 285 gt 160 C 320 gt 180 C 355 gt 200 C 390 gt 220 C 430 8 When temperature holding function working the Temp Hold indicator light will start flashing It means the temperature has not yet arrived at the setting temperature When the pan s temperature arrive the setting temperature the Temp Hold indicator light will keep steady on 9 Change temperature holding function to COOK function Push Select function key again and the function will back to COOK again Control Panel MODELA CU 22A 2 OFF Induction Range Temp 140 175 32 355 390 430 F Hold 60 80 0 6 80 200 220 C Power On Off Key Heating indicator light COOK function indicator ight HOLD Holding Temperature function indicator light COOK HOLD function select key Power Level Holding Temperature display LED lights COOK HOLD up down adjust keys NDOJ N FEATURES amp DESCRIPTION MODEL CU 22A 1 2 200watt Induction Heating Zone 2 Vitro Ceramic Glass Top Plate 3 Bottom Chassis 4 Power on off key 5 COOK function indicator light 6 Warm function Indicator Light 7 Air Intake 8 Air Outlet 9 Foot Stand 10 Wall Stopper Lock Washer You can find this accessory enclosed in the box Please screw this wall stopper into the back side of the induction range in order to keep enough distance for
6. e hob and the food When you switch off the cooking is stopped immediately PRECAUTION BEFORE USING YOUR INDUCTION HOB The glass top is of strong hard and non porous properties But in case of breakage even it s only slight cracking disconnect the appliance from the mains immediately and contact the after sales service 2 The appliances are equipped with small object detector But it s recommended not to place metal kitchen utensils pan lids knives or other metal objects on the induction heating zone If an inductor is switched on there is a risk of becoming hot 3 When using your induction hob don t place any magnet able objects on the glass top such as credit cards cassettes etc 4 Scientific tests have shown that the induction hob presents no danger Whatsoever for persons using pacemaker please keep 60cm 2 feet distance from the unit while the induction hob is in using 5 To prevent from overheating do not place aluminum foil or iron plate on the top plate 6 Putthe appliance on a horizontal surface but keep away from wall or articles at least 5 10cm 2 4 7 Do not put any articles like iron wire or tools into the air entrance or outlet to prevent from electric shock 8 Immediate clean up is recommended when water left on the top plate OPERATION INSTRUCTION 1 Plug power cord into 208VOLT 60Hz 15A power socket 2 Turn on power by pushing the power on off key power level display led light
7. h feet SAFETY DEVICE Overtime Detector If the pan is left on the induction range for more than 2 hours or if the user does not operate any functions for more than 2 hours the range will automatically shut off Automatic Safety Shut Off If the induction range is left on for more than 60 seconds without a pan or with an incompatible pan the unit will automatically shut off Material Compatibility Detector If the pan s material or its dimensions are not suitable for this induction range the pan indicator will not light Small Object Detector The induction range will not recognize any objects or utensils smaller than 5 CM in diameter For best results use pans that are between 12cm 4 75 and 26cm 10 25 in diameter Overheating Protection Device If the pan s temperature becomes too high and the temperature remains too high for 60 seconds the unit will shut off automatically And there will be a short warning sound after unit shut off automatically IC Auto Reset Device Main control microprocessor equipped with watchdog device the IC will auto reset when the software program goes wrong HOW DOES YOUR INDUCTION HOB WORK A high frequency 20 35KHz induction coil underneath the surface ceramic top plate heats the cooking utensil by magnetic friction The heat is produced directly within the pan It s controlled by electronic circuit to offer superior performance and functions During cooking no energy is lost between th
8. will come on 3 Push the power select key 4 up down to adjust the power levels from step 1 to step 9 4 Put a suitable pan on central position of top plate and push power control keys to desire power level Step 1 position is the minimum step 9 position is the maximum 5 Heating indicator light will indicate the pan is suitable or not If the Heating indicator light is on then the pan is heating If the Heating indicator light is off it indicates that the power is on but no pan or no suitable pan is on top plate position 6 This unit is equipped with over heating protection device which will stop power temporally when top plate temperature reaches 230 20 450 The power will start again automatically 4 when the temperature of top plate is reduced If you put an empty pan on it and heat up at max Power it will reach 230 450 very soon So the safety device will stop output power temporarily to prevent over heating Upon this situation the Heating indicator light will flash to indicate the over heating protection function is on 7 Temperature holding function Push Select key the temperature holding function will start working The LED indicates the temperature holding at60 5 140 push Temp select key 4 gt up down the LED indicate the temperature holding at80 175 Temp key gt function key pushed each time the holding temperature will be changed as control p
Download Pdf Manuals
Related Search