TIS 1830 User Manual - Test Instrument Solutions
Contents
1. e Polarization index measurement In insulation measurement mode select polarization index measurement by PI DAR key press this key once means selecting polarization index measurement screen display Timel 1min Time2 10min press TEST key means insulated polarization index measurement e Absorption ratio measurement In insulation measurement mode select absorption ratio measurement by PI DAR key press this key twice means selecting absorption ratio measurement screen display Time 30s Time2 1min press TEST key means insulated absorption ratio 1 measurement model press this key three times means selecting polarization index measurement screen display Timel 15s Time2 1min press TEST insulation absorption ratio 2 mode measurement 11 Battery Replacement See Below Danger To avoid possible electric shock remove all test leads from the instrument before replacing the battery Caution When replacing the batteries 18 Do not mix old and new batteries replace all old batteries with new batteries Please note battery polarity when install new batteries When you insert the new batteries roll the batteries using your hand to ensure contact Do not make any measurement when the battery compartment is open When the symbol Pe appears on the LCD it means that the batteries must be replaced Please follow the steps below 1 Turn off the power move rotary knob to OFF and re move all test leads that2. 99 9 250V 1 short circui Measurement 0 1MQ MQ 3 5 t current IMQ 100 MQ 5 5GQ about 2mA 500V 0 0IMQ 5 5 2 Less than 0 IMQ 4MQ buzz IMQ er alarm T000V 0 01M Q sound 3 The VIMO measuring IMQ range is as follows 250V 0 00 MQ 5 5GQ 500V 0 00 MQ 5 5GQ 1000V 0 00 MQ 5 5GQ Low Q Measurement 200Q 0 01 2 3 10V AC short circuit and 10V current gt 200mA DC Voltage measurement 750V AC 1V 2 3 750V AC 1 input Vac resistance 10MQ 2 min Voltage measureme nt 30V 3 frequency 50Hz 50Hz DAR DAR Imin insulation resistance 30s insulation resistance measurement DAR DAR Imin insulation resistance 15s insulation resistance measurement PI Polarization index 10min insulation resistance 1 min insulation resistance measurement Self checking Internal 10MQ resistor runction Battery level When Battery voltage lt 7V the low voltage symbol display indicator Test lamp When testing the insulation the test lamp is on Backlight Yes 5 Front View of Instrument See Front View of Instrument 1 Earth Terminal for insulation measurement 2 G negative jack for voltage measurement 3 V positive jack for voltage measurement 4 Line high voltage output for insulation resistance measurement 5 Led Display 6 Zero backlight 7 Conversion switch for absorbtion ratio and P I measurement 8 Test Button 9 Rotary Control Switch INSULATIONICONTINU
3. shock or personal injury follow these instructions and use the unit only as specified in this manual Do not use the unit or test leads if they appear damaged or if the unit is not operating properly If in doubt have the unit looked at e Always use the proper function and range for measurements When carrying out any test on insulation or continuity ensure there is no voltage present This could cause injury or damage to your unit which will not be covered by your warranty 2 Connect the test leads to the correct terminals when testing e Before rotating the function range selection switch disconnect test probe from circuit under test e Verify the Tester s operation by measuring on a known voltage source for voltage measurement e Verify the Tester s operation by measuring on a known resistance source for resistance measurement Or propriety Checkbox Do not apply more than the rated voltage as marked on the Tester between the test probe or between any test probe and earth ground e Do not use in distribution systems with voltages higher than 660V AC e Use the Tester with caution for voltages above 30 Vac rms 42 Vac peak or 60 Vdc These voltages pose electrical shock hazards e Disconnect circuit power and discharge all high voltage capacitors before testing insulation resistance and continuity Do not use the Tester around explosive gas or vapour e When using the test probes keep your fingers behind the finger
4. ITY TESTER 7S1890 cE renot gt ises PUDAR FNAN j Q ALZ tne A cf 6 7 8 9 Front View of Instrument Sabon Aa Ba i Tee V GABBY TIS 1830 LCD Display 6 Key and Rotary Switch Function Cutter 1 PI DAR Polarization index measurement absorption ratio measurement 2 ZERO LIGHT open or turn off backlight low resistance is zero 3 TEST open or turn off insulation low resistance measurement 4 AC voltage measurement is carried out when cutter points to ACV 5 Low resistance measurement is carried out when cutter points to CONTINUITY 6 Insulation resistance measurement is carried out when cutter points to 250V 500V 1000V respectively select the required output voltage 7 Preparations before Measurement After turning the instrument on the LCD display indicates on the left side the condition of the battery if the display indicates low voltages see symbol below the battery must be replaced Please replace with Alkaline 1 5v AA 9 Low voltage symbol Battery voltage TV or even less 8 AC Voltage Measurement AC voltage measurement figure INSULATIONCONTINGITY TESTER Carrying out ACV Measurement i Use the proper function and range for measurements To avoid possible electrical shock personal injury or damage to the tester disconnect circuit power and discharge all high voltage capacitors before testing resistance diode capacitance and temperature Always conne
5. TIS 1830 Digital Insulation amp Continuity Tester Instructions Contents 1 Overview 2 Safety Warning 3 Symbol Features 4 Technical Specifications a Test index of insulation resistance b polarization index measurement of absorption c low resistance measurement index d voltage test index 5 Front View of Instrument 6 Key and Rotary Switch Function 7 Preparations before Measurement 8 Voltage Measurement 9 Low resistance measurement 10 Insulation Resistance Measurement 11 Battery Replacement 12 Maintenance and Repairing 13 Guarantee amp Repair 1 Overview TIS 1830 is a digital insulation test instrument which features a brand new design combining a mass integrated circuit and digital circuit parameter measurement of insulation resistance low resistance and AC voltage is included The instrument has functions which include higher accuracy stable performance and simple and reliable operation It is designed to allow testing to BS7671 IEE 17 Edition Regulations amp EN 61557 1 2 4 10 Conforming to EN 61010 1 3 Edition Category 111 600v IP40 to EN60529 EN 61010 2 031 and EMC EN 61326 1 2 Safety Warning Design Manufacture amp Operation of the instrument meets IEC61010 safety standard This manual contains safety use and status of the instrument as well as warning and safety regulations which user must observe Warning Read before using your Tester e To avoid possible electrical
6. are connected to the tester 2 Loosen screw on battery box move the cover and replace all of the batteries 3 After replacing the batteries make sure the screw is secured 12 Maintenance and Repairing Clean the surface with clean water and soft cloth or sponge To avoid damage to test instrument do not put it in water If the instrument is wet dry it before storage Other than replacing the batteries all other remedial work must be carried out by an Authorised Repair Center or returned to an Authorised Distributor Any repair or remedial work carried out by any other person or persons will void your guarantee 19 13 Limited Guarantee and Limitation of Liability Your Unit will be guaranteed free from defects in material and workmanship for year from the date of purchase unless local laws require otherwise You can extend your guarantee period to 2 years for free providing the unit is calibrated by Test Instrument Calibrations at the end of the lst year This guarantee does not cover fuses batteries test leads or damage from accident neglect misuse alteration contamination or other conditions of operation or handling Our distributors are not authorised to extend any guarantee on our behalf To obtain service during the guarantee period return the product with proof of purchase to your distributor this guarantee is your only remedy all other guarantee whether express implied or statutory including imp
7. ct the test leads to the correct terminals when testing Before rotating the function range selection switch disconnect test probe from circuit under test Always test on a known circuit before carrying out any testing Do not use in distribution systems with voltages higher than 660V AC s Use the Tester with caution for voltages above 30Vac 42Vac peak or 60Vdc These voltages produce the risk of electrical shock which may cause other risks such as falling from a ladder etc Measurement of AC Voltage 1 Turn the rotary knob to AC V position 2 Use the V and G terminals for this test with the appropriate test leads 3 The display will show the measurement of AC voltage Measurement of Continuity e Disconnect circuit power and de energize the circuit before test 11 Do not measure continuity at live voltage circuit e Warning buzzer will sound when the tester detects a voltage of greater than 10Vac or de The display shows Uext and warning symbol Remove the test leads and isolate the voltage 9 To carry out measurement of continuity 1 Turn the rotary knob to continuity position 2 Use EARTH and G terminals for this test with test leads 3 Before making a continuity measurement use ZERO function to zero the test lead resistance To carry out test lead zeroing A Connect the test leads to EARTH and G terminals and short circuit the test leads using crocodiles and or probes B Press the TEST bu
8. guards Do not touch the circuit under Test Before and after testing verify there is no presence of hazardous voltage at the terminals e Remove test leads from the Tester before opening the Tester s case or battery door 3 Symbols s Caution Risk of electric shock Caution Refer to the explanation in this Manual The equipment is protected by double insulation or reinforced insulation Do not use in distribution systems with voltages higher than 660 V Earth Ground Battery Complies with European Directives Do not dispose of this product as unsorted municipal waste Contact a qualified recycler nie o 4 Technical Specifications Accuracy of reading LSD Maximum Display 1999 count Ambient Temperature 23 C 5 C Operating Altitude lt 2000M Working Temperature 0 C 35 C Relative Humidity lt 70 Storage Temperature Range 0 C 60 C Battery Alkaline 6 x 1 5v AA Dimensions LxWxH 161x102x70 Weight 502g TIS 1830 SPECIFICATION Function Range Resolution Accuracy Tolerance Open circuit voltage 250V 1V 0 10 250V Instrument itself 500V 1V can generate the 1000V 1V voltage Rated measurement ImA 0 10 250V 250V Under 250K current ImA Q ImA 500 Under 500K Q 1000V Under 1M Q Short circuit current about For reference LINE AND 2mA EARTH end of the high voltage output is short Insulation 250 0 01M Q 0 00 MQ
9. lied guarantees of fitness for a particular purpose or merchantability are hereby disclaimed manufacturer shall not be liable for any special indirect incidental or consequential damages or losses arising from any cause Repair All units that are returned for guarantee or non guarantee repair or for calibration should be Returned to your local distributor with the following your name company s name address telephone number and proof of purchase Additionally please include a brief description of the problem or the 20 service that you need and include the test leads with the unit For units out of guarantee you may be required to pay for the repair before the work will be carried out Under Guarantee Repairs and Replacement Please read the guarantee statement and check your battery and fuses before requesting repair During the guarantee period any defective unit can be returned to your distributor Printing errors are accepted P N 110401104084 21
10. st leads are separated and are not crossed together 7 Do not short circuit the two test leads during output of DC the voltage is presents at the output terminals Do not attempt to touch the circuit under measurement Warning symbol on the display will indicate a hazardous output voltage is present at the terminals When the measurement is completed do not touch the circuit as the circuit may store energy which may cause an electric shock Allow time for the circuit to discharge or discharge the circuit capacitors after the measurement How to measure insulation resistance 1 Turn the rotary switch to 250V or 500V or 1000V position as required 2 Use LINE and EARTH terminals for the test with test probes or crocodile clips connected to the circuit under test 3 Press TEST button to begin insulation resistance test TEST button will hold for continuous measurement Red warning light on TEST button indicates the presence of hazardous voltages at the terminals The primary display shows the insulation resistance reading The secondary smaller digits on the right side display indicates the actual output DC 15 voltage that was present during the actual test Buzzer threshold 4Mohms INSULATION Or ee INSULATIONICONTINUITY TESTER Insulation Resistance Measurement Chart 16 INSULATIONICONTINUITY TESTER T1 1830 az 1o00v ZERONE gt 280e PUDAR soove 250V conmmunve acv trsov 1 or self checking
11. tton continuous measurement The display will show the Resistance reading of your set of leads including crocodile and or probes C Press the ZERO and hold the TEST button Zeroing of your leads is complete when the display shows 0 00Q ZERO appears on display Note e The ZERO function can subtract up to 10Q of lead resistance Audio sound for lead resistance 12 Zeroing of your leads is advised to be repeated whenever you switch to the continuity function Please re check whenever you turn off or switch to another function Zeroing of test leads with a resistance gt 10 Q is not possible There is a buzzer warning sound Display retains measured test lead resistance the ZERO annunciator will not appear on the display 4 Press TEST button continuous measurement The primary display shows the continuity resistance The secondary display smaller digits on the right hand side will show the actual output of DC voltage The buzzer threshold is lt 20 ohms with the audio displayed on the screen CONTINUITY INSULATIONICONTINUITY TESTER 1830 ce Temora Then PUDAR Test v gt rf joeni AAAA Low resistance measurement chart Safety warnings prior to carrying out Insulation Measurements Disconnect power to the circuit under test and de energize the circuit before test Capacitors etc 14 Do not measure insulation on a live voltage circuit When measuring insulation resistance make sure the two te
Download Pdf Manuals
Related Search