EAT E-Flat turntable
Contents
1. 16 in to the thread of the suspention Operation and adjusting of the turntable Turntable unit must be in the perfect straight position This we will achieve by Adjustable feet 17 Set up the height and the levelling of the chassis by turning the feet to the left side or right By turning the feet to the right the chassis will raise turning the feet to the left will lower the turntable You can check the level by the levelling gauge if you have one Setting of the vertical force on the pickup stylus The value of the vertical force is recommended value of the cartridge You will find it in the technical description of your cartridge For cartridge up to 10g weight you should use Counterweight 18 already mounted on the tonearm Ease up the counterweight matrix 19 to adjust the required vertical force Cartridge with the weight more than 10 grams use the other counterweight that you find in the accessories box Setting VTA parallelism of the tonearm tube with the vinyl record Tonearm is from the factory preinstalled for the cartridge Blue Point 17mm To correct the VTA for the required level please follow our instruction below Sink down the tonearm by the Tonearm lift 20 direct to the vinyl record in a place where the groove is closing Loose the VTA building screw 21 This way you enable the hang up in the vertical direction By holding the Antiscating Hang up 15 by pressing or releasing you will set the required le2. the Tightening disc while centering the Platter 5 into the hole of the turntable chassis 7 and install the Platter 5 on the Sub Pletter 1 In the next step assembly the Tonearm 8 that you find in the accessories box inside of the packaging Mounting of the Cartridge 9 to the Tonearm 8 If you purchased one of our EAT cartridges please install it to the flat carbon tonearm now Install screws that are part of the cartridge box into the oval holes of the tonearm and fix it into the cartridge holes from the bottom side of the carbon tonearm Connect the cartridge system with the Tonearm cables White Left channel L Red Right channel R Green Right channel R Blue left channel L Now the tonearm is prepared Install prepared tonearm on the tip of the Tonearm pivot point 10 Install the Isolation connector 11 of the tonearm output to the Plug of the isolating connector 12 Be sure that it is properly inserted The locating pin of the connector is facing to the counterweight of the tonearm After inserting secure the isolation connector by fully tightening of the union nut It remains to complete the Antiscating disc 13 with hanging nylon hair that is ended by a small eye on one end Antiscating disc 13 set on the pin of the antiscating rider 14 Belt up the antiscating hair in the groove around the perimeter of the Hang up 15 and the eye of the antiscating hair hook to the Fixing screw 16 You tighten fixing screw
3. EXT EuroAudioteam s r o INSTRUCTIONS FOR USE EAT E Flat Dear Music Lover Welcome Congratulations on your purchase of our EAT E Flat turntable Your EAT E Flat was hand crafted by our team of skilled technicians It has been tested rigorously and is ready for your enjoyment Please take the time to read this manual carefully to ensure that you obtain the ultimate performance from your EAT E Flat turntable The tips contained within will ensure that your Forte will remain as new condition for many years to come Your EAT Consultant is Serial Number EAT E Flat Your contribution to environmental protection Disposal of packaging material Packaging protects the device from damage during the transportation The packaging materials were chosen with the regard to the environmental protection and they are therefore recyclable Disposal of old equipment For the disposal of old equipment use a junk place appointed for that purpose Controls features connections and parts of the turntable 1 Sub Platter 2 Sub Platter shaft 3 Pulleys of the motors 4 Drive belt 5 Platter 6 Tightening disk or record clamp 7 Plinth or chassis of the turntable 8 Tonearm 9 Cartridge 10 Tonearm pivot point 11 Isolation connector 12 Plug for the isolating connector 13 Antiscating disc 14 Antiscating rider 15 Hang up of the antiscating 16 Fixng screw for the antiscating hair 17 Adjustable feet 18 Counterweight 19 Cunt
4. cted to the power than on the User Panel 29 will light the green light button STBY STOP By pressing the button 33 or 45 you will choose the required speed to reproduction of the record vinyl The button will start to blink and after the reaching the right speed will light constantly To stop the turntable you press button STNBY STOP W As a safety precaution always disconnect the record player from the mains power supply before maintenance Technical specifications EAT E Flat Electronic speed change 33 33 45 11 Speed variance 0 09 Wow and flutter 0 01 Signal to noise ratio 73dB Dimensions of the turntable 500x400x100mm WxHxD Dimensions of the transport 710x365x590mm box Turntable weight 18 7kg Weight 42kg turntable including the wooden transport box Chassis material MDF Belt Material silicone rubber Motor 2x synchronized controlled by microprocessor Drive belt Speed changer electronically illuminating buttons Platter Aluminium Magnesium diameter 340mm weight 6 9kg damped Input 20W DC Outboard power supply switching power supply 100 240V AC 50 60Hz Tonearm Flat carbon Effective length 254mm 10 inch Effective mass 4mm 19 58 3mm 12 58 Mounting distance 238mm Overhang 16mm Range of adjustment for vertical force on stylus 0 3g Angel 24 11 Useful tips The base and the record player should be positioned on a low resonance surface such as wood or multiple layer ply board to avoid structural v
5. erweight matrix or nut 20 Tonearm lift 21 VTA building screw 22 Lift lever 23 Tonearm support 24 Jack holder 25 Antiscating weight 26 Turntable power connection 27 Signal output 28 Grounding terminal for signal cable 29 User panel The device is shipped partially disassembled in order to avoid damage to sensitive parts Please double check immediately after receiving it if the packaging and the device were not damaged during the transportation If damaged please do not operate Compare the data for the electrical connection on the type plate of the turntable with your network data Data must be compatible to prevent damage to the turntable W Warning of a hazard for the user the unit or possible misuse 8 12 KTO polohovac kolik konektoru 21 25 zapich 3 zapich 2 zapich 1 Before Using Assembly the turntable from the parts that are inside of the package Remove the cover protection from the Sub Platter Shaft 2 and check if there is enough grease You will find the additional grease in the accessories if the shaft is not enough lubricated Place the Sub Platter 1 on the Shaft 2 Place the Drive Belt 4 on the Pulley of both Motors 3 You need to install the Tightening Disc 6 to the Platter 5 by screwing 1t to the thread of the platter pin After you successfully installed the Tightening disc to the platter and disc is holding firmly on the platter you can install the platter Hold
6. ibrations disturbing replay Mains power connection The turntable is supplied with a power supply suitable for your country s mains supply Check the label before connecting to ensure compliance with the mains rating in your home If the player is not used over a long period of time the drive belt can be removed to prevent undesired stretching Service Should you encounter a problem which you are not able to correct or identify despite the above information please contact your dealer for further advice Only when the problem cannot be resolved there should the unit be sent to the distributor in your country Guarantee repairs will only be affected if the unit is returned correctly packaged For this reason we recommend keeping the original packaging Transport of the originally packed unit is possible only on the additional palette Never return a record player without making sure that is it safely disassembled and correctly packaged in the original packaging Please remove these parts and pack them separately feet counterweight platter cartridge and belt Fit the cartridge protection cap Insert the transport lock for the tonearm prior to carefully packaging the record player Warranty The manufacturer accepts no responsibility for damage caused by not adhering to these ES instructions for use and or by transportation without the original packaging Modification or change to any part of the product by unauthorised persons release
7. the manufacturer from any liability over and above the lawful rights of the customer The information was correct at the time of EAT EuroAudioTeam iS a Registered going to press The manufacturer reserves the Trademark of Jozefina Lichtenegger right to make changes to the technical Copyright 2010 All rights reserved specification without prior notice as deemed necessary to uphold the ongoing process of technical development 12
8. vel than you tighten the building screw 21 Now you check the correct function of the tonearm lift By the lifted lever 22 must tonearm securely sit on the Tonearm Support 23 If the Tonearm does not reach the level of the Tonearm support 23 than you can change the Jack Holder 24 position You set the cartridge system with protractor Turntable Antiscating and its adjustment zapich 1 zapich 2 zapich 3 With help of the Antiscating rider 14 you can adjust the position of the tonearm antiscating weight cca 45 For the vertical force of the stylus up to 13mN use position of the counterweight in Stuck Nr 1 13 18mN use position of the counterweight in Suck Nr 2 18 25mN use position of the counterweight in Stuck Nr 3 Stuck Z pich Connecting of the turntable We use the switching power supply 90 246V AC 47 63Hz Plug the flex cord into the power plug Input from the source that is ended by 4 pin connector plug into the Grounding terminal of the signal cable 28 On the user panel 29 will light up the green button Connecting of the turntable output The signal cable that you find in the accessories of the turntable connect by the Chinch connectors into the Signal output box 27 Make sure that the colours are connected on the right place R red channel L white channel Grounding cable connect to the Grounding Terminal 28 Operating the turntable 0 3 O BE 10 If your turntable is conne
Download Pdf Manuals
Related Search