UltraView UVD-6130VE-2 WDR Dome Camera User Manual
Contents
1. User guidelines e Program the camera settings as much as possible before mounting the camera Take appropriate safety precautions while completing programming after installation Always use a 12 VDC or 24 VAC UL listed Class 2 power supply to power the camera e Do not use the camera over the temperature range specifications 10 C to 50 C 14 F to 122 F e Ifthe light source where the camera is installed experiences rapid wide variations in lighting the camera may not operate as intended WARNING To reduce the risk of fire or electronic shock do not expose the camera to rain or moisture and do not remove the cover or back Product description Figure 1 Camera description zx Camera body W OSD control pad System heater q ui p PAE A T AY o i ower jac r Monitor output cable Video monitor output Video output BNC 1 Monitor output BNC 2 Monitor output RCA OSD control pad The onscreen display OSD control pad Figure 3 is a five direction pad that provides the ability to manually control the camera functions Table 1 below lists the OSD control pad functions and describes their use UltraView UVD 6130VE 2 WDR Dome Camera User Manual Figure 2 OSD control pad OSD control pad Table 1 OSD control pad functions Pad directions Description Up Moves the cursor upward to select an item Left Moves the cursor left to select or adjust the options of the2. 6 Heset camera settings 16 Save all changes 16 Specifications 17 Dimensions 17 Menu Map 18 UltraView UVD 6130VE 2 WDR Dome Camera User Manual Product overview The UVD 6130VE 2 WDR camera uses a digital signal processor DSP to process video signals The camera includes a microcontroller to provide high quality images with high color reproduction and sharp pictures Package Contents The package contains the following Dome camera Monitor output cable Mounting screws wall anchors and hex wrench Power terminal Ceiling drilling holes template Quick start guide Note Use the video output BNC and power jack for normal system operation Use the monitor output cable for installation and maintenance Features The camera includes the following features Super HAD II hole accumulated diode technology with 480 000 pixels NTSC 570 000 PAL Use of LSI large scale integration digital processors to produce 650 lines of horizontal resolution Smart digital control automatic BLC backlight compensation WDR wide dynamic range Advanced auto exposure system for both fixed iris and auto iris lenses to optimize the amount of light Internal synchronization Eight privacy mask areas to protect privacy concerns Advanced OSD onscreen display control oignal to noise ratio better than 52 dB Long life and high reliability Isolated switching power 12 VDC and 24 VAC UltraView UVD 6130VE 2 WDR Dome Camera User Manual
3. El El interlogix A UTC Fire amp Security Company UltraView UVD 6130VE 2 WDR Dome Camera User Manual P N 1072549A REV 1 0 ISS 18JUN12 Copyright Trademarks and patents Manufacturer Certification FCC compliance ACMA compliance European Union directives Contact information 2012 UTC Fire amp Security All rights reserved The TruVision and Interlogix names and logo are trademarks of UTC Fire amp Security Other trade names used in this document may be trademarks or registered trademarks of the manufacturers or vendors of the respective products UTC Fire amp Security Americas Corporation Inc 2955 Red Hill Avenue Costa Mesa CA 92626 5923 USA Authorized EU manufacturing representative UTC Fire amp Security B V Kelvinstraat 7 6003 DH Weert The Netherlands CE Quis Class A This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct th
4. X0 75 or X1 AGC Max Adjust the maximum automatic gain control level The value can range from O to 7 UltraView UVD 6130VE 2 WDR Dome Camera User Manual Traffic shutter menu TRAFFIC SETUP SHUTTER TMI 1 0060 LOW LUMINANCE MODE AGC BRIGHTNESS X0 25 AGC MAX MI HL 002 RETURN Shutter Set the manual shutter to 1 60 1 50 1 100 1 120 1 250 1 500 1 1000 1 2000 1 4000 1 10000 1 20000 or 1 50000 Select a higher value to see movement and a lower value to see clearer images Low luminance Sets the lux level for low light conditions Mode Only AGC available Brightness Select the brightness level to X0 25 X0 50 X0 75 or X1 AGC Max Adjust the maximum automatic gain control level The value can range from O to 7 Adjust the picture characteristics In the Setup menu go to Pict Adjust and select the options to be modified in the menu S PICT ADJUST MIRROR OFF CONTRAST TN 032 SHARPNESS MH 032 RETURN oet the camera image characteristics of the picture contrast and sharpness The parameters of each can be set between 0 and 255 Use the mirror function to flip the camera image so that it is correctly orientated for viewing The image can be flipped vertically horizontally or horizontally vertically 180 degrees Default setting is Off Set white balance White balance WB tells the dome camera what the color white looks like Based on this information the dome camera will then continue t
5. a to factory default settings Saves changes made Exits the menu and returns to live mode UltraView UVD 6130VE 2 WDR Dome Camera User Manual To access the Setup menu 1 Press the OSD control pad Enter to access the Setup menu and its submenus Push the pad up down left and right to move between menu options Press the OSD control pad to select an option When in a sub menu select Return to return to the previous menu Ok deme OILS To save configuration changes move the cursor to Save All at the bottom of the screen and press Enter 6 To exit a menu and return to live mode move the cursor to Exit at the bottom of the screen and press Enter Select the lens type In the Setup menu go to Lens and select the type of lens used with the camera Auto or Manual Select Manual for a manual lens and adjust the options manually or select Auto to set the lens type to autoiris The Autoiris menu appears Autoiris menu f AUTOIRIS TYPE DC MODE AUTO SPEED CT 85 RETURN Type Select the drive mode of the lens Only DC is available Mode Select the iris control mode Auto automatically controlled depending on the light Open always open or Closed always closed Speed When the mode is set to Auto select the convergence speed of the iris between 0 and 255 Set shutter AGC In the Setup menu go to Shutter AGC and select the required iris control option Manual Auto or Traffic Auto is default The s
6. at is user defined by blue and red gain parameters Only use this function when there is steady light Blue gain from 0 to 255 Red gain from 0 to 255 This is a second fixed white balance that is user defined by blue and red gain parameters Only use this function when there is steady light Blue gain from 0 to 255 Red gain from 0 to 255 The anti color rolling mode function minimizes the color changes over long periods caused by very small differences between the flicker frequency of non inverter fluorescent lights and the drive frequency of the image sensor devices Manually adjust the white balance by blue gain only The red gain is automatically adjusted when the blue gain is changed Only use this function when there is steady light Level UP Press Enter to increase the WB level Level DOWN Press Enter to decrease the WB level Press Enter to automatically adjust the white balance to the environment and lock it at this value Wide dynamic range WDR allows you to see details of objects in shadows or details of objects in bright areas of frames that have high contrast between light and dark areas such as the headlights of a passing car In the Setup menu go to WDR and select the options to be modified in the menu UltraView UVD 6130VE 2 WDR Dome Camera User Manual 11 S WOR SETUP MODE CONTRAST RETURN Adjust the mode by pressing left or right to cycle between Full and Normal If you select Full Mode adjust t
7. ave up to 40 characters CAMERA ID Camera ID input line ABCDEFGHLIRKLMNOPQRSTUV WXYZ0123456789 Sd r5 s n0 eJ ti CRT POS Command line RETURN To enter a character move the cursor to the desired character and press Enter to select it It appears in the input line Repeat the process until all characters are entered To move the character input position in the input line move the cursor in the command line to or and press Enter To clear the input line move the cursor to CLR and press Enter To delete a character in the input line select the character so that it blinks Then move the cursor to CLR on the command line and press Enter To position the camera ID on screen move the cursor to POS and press Enter The menu will then disappear on screen and the camera ID will be displayed on the monitor Use the menu button to move the camera ID to the desired position Press Enter The menu will reappear Select Return to return to the previous menu Select the language In the Setup menu go to Language to open its menu Use this menu to select the OSD language Select the desired language There are only two languages available English and Japanese Reset camera settings Use this menu to reset the camera settings to factory default In the Setup menu go to Camera Reset Press Enter to reset all camera values to factory default Save all changes Changes are not saved automatically To save all c
8. ble this option to see the mask as a mosaic It is disabled by default Note Only four privacy mask areas can be set when motion detection is enabled Set motion detection In the Setup menu select Motion Det to open the motion detection menu Use this function to identify when a moving object passes in front of the camera to activate an alarm Up to four motion detection areas can be configured each by size and location on screen S MOTION DET DETECT SENSE ITM 111 BLOCK DISP OFF DETECT AREA MONITOR AREA RETURN Detect sense Set the sensitivity level for motion detection A higher value is more sensitive Block Disp When enabled any movement detected will be tracked on screen Press Enter to enable or press the button again to cancel it The default setting is Off no motion detection Detect Area Up to four motion sensitive areas can be set Set the size and position of each one Monitor area Enable a square grid to be displayed on screen and set its position It can only be set if Block Disp is enabled Display the synchronization mode In the second Setup menu go to Sync to open the synchronization menu Use the Sync menu to display the current synchronization mode Only one option is available Internal UltraView UVD 6130VE 2 WDR Dome Camera User Manual 15 Set the camera ID In the Setup menu go to Camera ID to open its menu Press Enter to display the menu The camera ID displayed on screen can h
9. e interference at his own expense Notice This is a Class A product In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures 12004 108 EC EMC directive Hereby UTC Fire amp Security declares that this device is in compliance or with the essential requirements and other relevant provisions of Directive 2004 108 EC 2002 96 EC WEEE directive Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union For proper recycling return this product to your local supplier upon the purchase of equivalent new equipment or dispose of it at designated collection points For more information see www recyclethis info For contact information see www utcfireandsecurity com or www utcfssecurityproducts eu Content Product overview 2 Package Contents 2 Features 2 User guidelines 3 Product description 3 OSD control pad 3 Installation 5 Mount the camera 5 Connect the cables 5 Adjust the lens 5 Adjust the focus and zoom 6 Programming 7 Access the Setup menu 7 Select the lens type 8 Set shutter AGC 8 Adjust the picture characteristics 10 set white balance 10 Set WDR 11 oet image noise reduction 12 Set HLC andBLC 12 Set Day Night mode 13 Set E zoom 14 Set DIS 14 Set the privacy mask area 14 set motion detection 15 Display the synchronization mode 15 Set the camera ID 16 Select the language 1
10. elected menu appears 8 UltraView UVD 6130VE 2 WDR Dome Camera User Manual Automatic shutter menu S AUTO SETUP HIGH LUMINANCE MODE SHUT BRIGHTNESS ME HUI 32 LOW LUMINANCE MODE SLOW AGC BRIGHTNESS X0 25 AGC MAX THE HIE 002 RETURN Select the parameters for high and low luminance conditions High Luminance Sets the lux level for bright light conditions such as daylight Mode When lens type is AUTO IRIS you can choose SHUT AUTO IRIS or AUTO IRIS mode When the lens type is manual only SHUT mode is available Brightness Select the brightness level to which the iris and shutter speed will adjust automatically The values range from 0 to 255 Low luminance Sets the lux level for low light conditions Mode Select Off AGC Slow AGC Slow Slow AGC or AGC Slow AGC Brightness Select the brightness level to X0 25 X0 50 X0 75 or X1 AGC Max Adjust the maximum automatic gain control level The value can range from O to 7 Manual shutter menu ien MANUAL SETUP SHUTTER TTI 1 0060 LOW LUMINANCE MODE AGC BRIGHTNESS X0 25 AGC MAX Hi nm 002 RETURN Shutter Set the manual shutter to 1 60 1 50 1 100 1 120 1 250 1 500 1 1000 1 2000 1 4000 1 10000 1 20000 or 1 50000 Select a higher value to see movement and a lower value to see clearer images Low luminance Sets the lux level for low light conditions Mode Only AGC available Brightness Select the brightness level to X0 25 X0 50
11. etup menu provides access to the camera configuration options The on screen display OSD is only available in English Program the camera by attaching a standard video monitor to the system Figure 5 The Setup menu screens f SETUP MENU 1 2 LENS BHUTTIEBR AC PICT ADJUST WHITE BAL ATE EX NR NEAT EXIT AUTCLI ALTO ATW SAVE SETUP MENU 2 3 En SETUP MENU 3 3 HLC ELC SYNC aj DAY NIGHT CAMERA ID EZOGOM a LANGUAGE H DIS CAMERA RESET PRIVACY MOTION DET NEXT BACK ALL EXIT SAVE ALL EXIT SAVE ALL Table 2 Setup menu description Menu item Lens Shutter AGC Pict Adjust White Bal WDR NR BLC HLC Day Night EZoom DIS Privacy Motion Det Sync Camera ID Language Camera Reset Save All Exit Description Defines the camera ID mirror and digital noise reduction DNR set up Defines the method of iris control Defines the image quality functions Defines the white balance WB set up Defines the wide dynamic range WDR set up Defines the digital noise reduction level Defines the highlight compensation HLC and backlight compensation BLC set up Defines the day night D N set up Enables disables digital zoom Enables disables the digital image stabilizer Defines privacy mask set up Defines the motion detection set up Displays the current synchronization mode Defines the camera ID displayed on screen Defines the language of the OSD Resets the camer
12. hanges made move the cursor to the Save All option in the Setup menu and press Enter 16 UltraView UVD 6130VE 2 WDR Dome Camera User Manual Specifications Model UVD 6130VE 2 P UVD 6130VE 2 N Lens type Varifocal 2 8 to 10 mm Power supply 24 VAC 12 VDC Current 300 mA Max 450 mA heater on Power consumption 3 W Max 10 8 W heater on Operating temperature 30 to 50 C 22 to 122 F Weight 1130 g 2 49 Ibs Dimensions 5 22 in 133 mm d NN UltraView UVD 6130VE 2 WDR Dome Camera User Manual wu yS ww TS utere uui SOT ul TT Ul 66 T Menu Map setup Menu Manual A Lens uto T F Auto Shutter AGC Traffic MirrorManual F Contrast iid Pict Adjust Sharpness SS 4 User 1 User 2 White Bal Anti CR Manual WBR Push Lock 2DNR NR 3DNR ALC Clip Level HLC BLC Scal Birt BLC Delay CNT Auto Day gt Night Day Night Color Night gt Day Ezoom Area Set Mode DIS Position Color Privacy Transp Mosaic Motion Det Detect Sense Block Dsip Sync Detect Area Camera ID Monitor Area Language Camera Reset Save All Exit UltraView UVD 6130VE 2 WDR Dome Camera User Manual
13. he 12 VDC or 24 VAC power supply to the power jack of the camera Caution Check for polarity when using a 12 VDC power supply Adjust the lens The camera is mounted on a pan tilt twist 3 axis grimbal rotating platform so that it is easy to adjust the camera orientation See Figure 3 on page 6 UltraView UVD 6130VE 2 WDR Dome Camera User Manual 5 Figure 3 Camera adjustment Platform horizontal adjustment 0 to 180 An Platform vertical adjustment 0 to 90 E Ps F aay fa 1 2d Rotor horizontal adjustment 0 to 350 Ma is F k F e Tuer To adjust the lens oee Figure 3 above 1 To adjust the horizontal angle of the platform up to 180 degrees turn the platform 2 o adjust the horizontal angle of the rotor up to 350 degrees turn the rotor on the platform 3 To adjust the vertical angle of the platform up to 90 degrees turn the platform Adjust the focus and zoom Figure 4 Zoom and focus adjustment Zoom ring thumbscrew Focus ring thumbscrew To adjust the camera zoom and focus 1 Loosen the zoom ring thumbscrew and turn the zoom ring to set the desired zoom Tighten the thumbscrew 2 Loosen the focus ring thumbscrew and turn the focus ring to set the desired focus Tighten the thumbscrew 6 UltraView UVD 6130VE 2 WDR Dome Camera User Manual Programming Once the camera hardware has been installed the camera can then be configured Access the Setup menu The S
14. he contrast by pressing left or right to cycle between Low Midlow Mid Midhigh or High Set image noise reduction In the Setup menu go to NR Setup and select the desired digital noise reduction DNR levels 2D 3DNR technology minimizes noise and ghosting It produces clear images under low light levels S NR SETUP 2DNR ON 3DNR MIDLOW RETURN Menu Item Description 2DNR Enable or disable the option Default is On 3DNR Select the level of noise reduction from Low Midlow Mid Midhigh High or Off High levels can blur the image Set HLC and BLC This feature tells the camera to adjust its total exposure iris and shutter in order to ignore the brightest areas of the image and instead concentrate on darker areas HLC highlight compensation masks strong light sources giving darker areas more detail It is often used to help identify vehicle license plate numbers for example BLC backlight compensation can improve image quality when the background illumination is high It prevents the object in the center from appearing too dark The Clip level option allows you to black out the bright vehicle headlights in the image In the Setup menu go to HLC BLC and select the options to be modified 12 UltraView UVD 6130VE 2 WDR Dome Camera User Manual S HLC BLC HLC OFF CLIP LEVEL HM MIDLOW SCALE BLC RETURN HLC Enable or disable the option Default is Off Clip level Adjust the level between from Low M
15. idlow Mid Midhigh High or Off Scale Adjust the level between 0 and 255 BLC Enable or disable the option Set Day Night mode In the Setup menu select Day Night to open the day night menu The Day Night mode has two options Auto and Color Select Color to manually set the camera to color day mode Select Auto so that the camera can automatically switch between day color and night black and white mode Auto mode S DAY NIGHT SETUP BURST ON DELAY CNT Wn OOS DAY NIGHT nom Q2 NIGHT DAY Timm 005 RETURN Burst Enable disable the color burst component of the video signal when the camera switches to B W ON mode maintains the same color signal in B W so that the video signal provides better compatibility with certain color equipment OFF mode removes the color burst signal B W video and increase the total TV lines Delay CNT This is the time in seconds before Day Night switches A long delay response would be used for example to avoid switching from Night to Day mode when car headlights pass in front of the camera Day Night Set the threshold level on how dark it should be before switching from Day to Night mode Lower Higher value makes the camera switched from Day to Night at lower higher illumination Night Day Set the threshold level on how light it should be before switching from Night to Day mode UltraView UVD 6130VE 2 WDR Dome Camera User Manual 13 Caution If there is a minimal differe
16. nce between the Day Night and Night Day values then camera may switch between Day and Night mode Set E zoom Digital Zoom E zoom is the electronic magnification of a view In the Setup menu select Ezoom to open the menu Select the desired options S EZOOM SETUP MAG TM PAN HNN 02 TILT mum Q02 RETURN Menu Item Description Mag Adjust the electronic zoom Pan Adjust the horizontal picture Tilt Adjust the vertical picture Set DIS The DIS function digital image stabilizer helps to neutralize light camera vibrations In the Setup menu select DIS to open the DIS menu Enable or disable the option Set the privacy mask area In the Setup menu select Privacy to open the privacy mask menu Use this function to mask out selected areas of the image Up to 15 privacy mask areas can be configured each by size and location on screen S PRIVACY AREA SEL 1 15 MODE ON POSITION COLOR WHITE TRANSP 1 00 MOSAIC RETURN Area Sel Up to 15 privacy masks can be set 14 UltraView UVD 6130VE 2 WDR Dome Camera User Manual Mode Enable or disable the selected mask Position Press Enter to get the submenu to set position the mask on screen values Color Select the color of the privacy mask White Red Black Green Blue Yellow Cyan or Magenta Transp Select the transparency shade of the privacy mask The privacy mask is fully transparent at value 0 00 and not transparent at 1 00 Mosaic Ena
17. o display all colors correctly even when the color temperature of the scene changes such as from daylight to fluorescent lighting for example In the Setup menu go to White Bal and select the options to be modified 10 UltraView UVD 6130VE 2 WDR Dome Camera User Manual Menu Item ATW Push User1 User2 Anti CR Manual Push Lock Set WDR Description ATW automatic tracing white balance limits the color temperature range between 2 500 to 8 500 K to reduce excessive compensation for a large single color object Use it to automatically adjust the WB in real time as the lighting conditions change It can be used for both indoor and outdoor locations Set the following options Speed Set the compensation speed between 0 and 255 A lower value makes the AWB faster Delay CNT Set the delay time between automatic adjustments of the AWB A smaller value increases the frequency rate of AWB ATW Frame X0 5 X1 0 X1 5 X2 0 Default is X2 0 Environment Select Indoor ATW is compensated for low color temperature such as from incandescent lighting or Outdoor ATW is compensated for high color temperature such as from daylight Default is Indoor Like ATW the Push function continually monitors analyzes the color temperature of the incoming light and corrects the WB However Push has no limits between 1 800 to 10 500 K so it may over compensate the WB for a large single color object This is a fixed white balance th
18. selected item Moves the cursor to the right to select or adjust the options of the righ selected item Down Moves the cursor downward to select an item Press the center of the control pad to display the Setup menu If the Enter selected item has its own menu press the control pad to enter a submenu Press the control pad for 2 seconds to save all settings and exit the Setup menu 4 UltraView UVD 6130VE 2 WDR Dome Camera User Manual Installation Please check the package contents and make sure that the device in the package is in good condition and all the assembly parts are included To install the camera you will need to prepare the mounting surface mount the camera make cable connections adjust the lens and then secure the dome cover securely Note Before installing please ensure that the mounting surface is strong enough to withstand three times the weight of the camera If the mounting surface is not strong enough the camera may fall and cause serious damage Mount the camera Use the ceiling drilling holes template and mark the holes on the ceiling with a pen Attach the plate with fasteners to the ceiling and then attach the camera body to the plate To mount the camera attach the camera to the mounting surface using the appropriate fasteners Connect the cables To connect the cables 1 Connect a coaxial cable from the camera s BNC connector to a CCTV monitor or video recording device 2 Connect t
Download Pdf Manuals
Related Search