Paragon E User Manual
Contents
1. number key The bell is switched on to select next test The internal sounder is ES Switched on v Enter N to exit 10 Walk tes A T All zones chime when activated LEDs light when zones open Enter CS to exit RINS 011 ISSUE 1 13 5 Tamper Alarm activated sounding internal audible 5 PARAGON 3 FUNCTIONAL DESCRIPTION alarm Panel unset Day mode 3 1 Operating Modes SUPPLY DAY ZONE 1 Enter user code to clear internal audible alarm Re enter user code to clear TAMPER LED Now try setting the system If the system goes straight into an alarm condition contact the engineer Day Mode This is the state of the panel when unset not armed Fire Personal Attack and Tamper inputs however remain active 24hours aday These are referred to as 24 hour zones Day mode is identified by the green day LED on the front of the panel ZONE2 ZONE 3 ZONE 4 TAMPER PA Set Modes When the panel is set armed an activation of any Access Immediate or 24 hour zone will cause an alarm condition When an alarm is generated the internal and external sounders will operate for the length of time programmed and the tone of the internal sounder will be two notes repeated rapidly The strobe lamp will also be activated and will Oeoooooo0 TAMPER P A 6 Mains Failure Panel unset Day mode PARAGON continue to operate until the panel is reset Supply LED off indicating no mains supply to SUPPLY Fullset Partset panel2. Code RS E gt A 5 To AT ey then X User code 3 Bleeps then X X X Y New user code 3 Bleeps th G0 G0 G00 N de again 3 BI en X X X X New user code again 3 Bleeps The DAY led will flash when this function is entered and an acknowledge tone will be sounded after each code has been entered If an incorrect key is entered an error tone will be given and the function ended 6 12 System Test Mode PN SE Enter 26 This function performs a number of tests which are listed below The next test is selected by pressing any numeric key To exit system test mode press the key again Test 1 All LED s are switched on 2 The strobe is switched on 3 The bell is switched on 4 The internal sounder is switched on 6 13 Walk Test Mode Enter T When the walk test mode is enabled any activated zone will cause a chime and the LED display to indicate To exit walk test mode press the Key again 7 LED FUNCTIONS Supply light on Indicates there is mains on the system Day light on Indicates the system is unset Day mode Zone light on Indicates an Alarm activation Tamper light on Indicates a Tamper alarm P A light on Indicates a Personal Attack activation Tamper light flashing Engineer mode 10 5 CONTROLS AND FUNCTIONS Volume Control This is only accessible when the front cover has been removed and will only affect the volume of the internal sounder togeth
3. only generate an internal alarm if the panel is in Day mode If a tamper fault is present and the panel is then set the system will give a second internal alarm Triggering of a tamper zone when the panel is set will always give an external as well as internal alarm Triggering the fire zone will only operate the internal sounder A fire alarm is identified by a three note rising sound which is easily distinguished from all other tones Zone 4 may be configured as a fire zone not be regarded as a total fire protection system 8 TROUBLESHOOTING KEY 2 LEDOFF LEDON LEDFLASHING 1 Panel set on 2 Panel unset off 3 Panel unset Zone1 Zone 2 Zone 3 Zone 4 LEDs on This shows an alarm has occured on Zones 1 to 4 To clear alarm lights enter User code If the LEDs do not clear call engineer 4 Personal attack activated Enter User code to clear P A light Reset Personal Attack buttons if necessary If the LED does not clear call the engineer RINS 011 ISSUE 1 PARAGON SUPPLY DAY ZONE 1 ZONE 2 ZONE 3 ZONE 4 TAMPER P A PARABUN SUPPLY DAY ZONE 1 ZONE2 ZONE 3 ZONE 4 TAMPER PARAGON SUPPLY DAY ZONE 1 ZONE 2 ZONE 3 ZONE 4 TAMPER SUPPLY DAY ZONE 1 ZONE 3 TAMPER eooooooo0 0 00 PARAGON ZONE 2 ZONE 4 11 6 11 Changing User
4. DAY Check that there is mains supply else where Fone O the control panel any one of three set modes the premises If no supply in premises wait ZONE2 Fullset Whole system armed nobody on premises for mains power to there s mains Zzows Part set 1 Upstairs off Downstairs armed supply to the system contact the engineer ZONE4 Part set 2 Upstairs armed Downstairs off e The above are purely examples The Engineer has the ability at the programming stage to configure all the circuits to the customer s exact requirements PARADO 3 2 Entry Exit Mode SUPPLY L jw A Ae d DAY s Entry When the panel is set and an Entry Exit zone is triggered the ie Ped T zoNE1 Entry Exit timer will begin to count down During this period eee ZONE2 an Entry Exit tone single repeated bleep will be produced by the internal sounder and any zones which are programmed as 2 i Ener SET determinate 70 4 Access zones will be ignored If the user code is entered before TAMPER the end of the count down period the panel will return to day PA mode If the timer is allowed to elapse before the user code is entered the panel will go into an alarm state In this case the System needs to be Unset Exit With the panel in day mode if either the user code or an Easy set key sequence is entered the Entry Exit time
5. LS ANDFUNCTIONS USERFACILITIES 6 1 FULLSETTING THEPANEL 6 2 PART SETTING THE PANEL 6 3 UNSETTING THE PANEL 6 4 ACTIVATING THE PERSONAL ATTACK ALARM 6 5 ACTIVATING THE FIRE ALARM 6 6 TURNING CHIME ONAND OFF 6 7 RECALLING EVENT LOG 6 8 OMITTING ONE ORMORE ZONES 6 9 CLEARING THE EVENT LOG 6 10 CLEARINGTHE DISPLAY AFTER AN ACTIVATION 6 9 CHANGING THE USERCODE 6 10 SYSTEM TESTMODE 6 11 WALK TEST MODE LEDFUNCTIONS TROUBLESHOOTING USERQUICKREFERENCE GUIDES RINS 011 ISSUE 1 A A o CO o co co 10 10 10 11 13 1 INTRODUCTION The Paragon E is a full featured intruder alarm control panel based around a micro processor with 4 fully programmable zones and 2 dedicated 24 hour zones Personal Attack alarm and a System Tamper alarm It is operated via a 16 key onboard keypad and has an arrangement of 8 LEDs to show the status of the system All features are fully programmable and there are two levels of access to the system These are User amp Engineer The User level gives access to all setting and unsetting facilities and also allows the changing of code numbers and testing of the system The Engineer level gives total access to the system including the ability to reconfigure the system The Engineer cannot however unset the system 2 FEATURES 2 Access Level Codes both programmable Easy set facility 4 Programmable alarm zones 3
6. Set Part Set modes Configurable fire zone with unique alarm sound Personal Attack alarm zone Tamper zone 16 key backlit keypad Dedicated Personal Attack key on keypad Dedicated Fire alarm key on keypad 8 LEDs for immediate indication of panel status Walk Test facility System Test Function Built in sounder with volume control and software override Separate Bell and Strobe lamp outputs Zone omit facility on exit Silent part set NB your installation engineer will have programmed all the system features to ensure easy and convenient day to day use of your system see section Engineer Program mable Zones 9 USER QUICK REFERENCE GUIDE 1 Unsetting Enter Q0 00 00 00 Usercode 4 Re enter x x eV ao to clear LEDs Usercode 2 Fullset Enter AAO or Q0 Qo o Silenton exit 3 Part set 5 A Lan a Part set 1 Downstairs Aw 1 RK a gt a b Part set 2 Upstairs 26 6 or 2 NOTE Part sets are silent exit Tones will be heard on entry 4 To activate the Personal Attack alarm ente A vw 5 To activate the Fire alarm enter A y 6 Zone omit in exit mode AO x Q 7 Chime facility 4 1 Toggles chime on and off 8 Changing D C X Oldusercode XA User code ao x o0 9 NewUser code x C Qo NewUsercode 9 Test mode amp 6 mmgampAll LEDs are switched on Press any The strobe is switched on
7. er with any extension speakers The volume control is overridden when the panel is in an alarm state and also if the the panel has been set by the User code Chime Chime function applies to day mode only and if selected will cause the panel to generate a three note sound when an entry exit zone is triggered This feature is to inform the occupants of the building that someone has entered Latch The latch facility is designed to be used with intruder detectors fitted with a latch memory This feature is very useful when more than one detector has to be wired to a particularzone as it will show which detectors were triggered if an alarm occured If there has beenan alarm and latch memory was used then when the panel is reset an LED indication will be given at the relevant detector s Resetting of latch memory requires the panel to be set again for not less than 5 seconds and then unset Auto Rearm After an alarm the panel will automatically reset itself when the bell timer has expired Any zones which still remain triggered at that time will be ommited automatically Walk test The walk test function verifys that all the intruder detectors on the alarm system are functioning correctly When the walk test mode is enabled any activated zone will cause a chime and the LED display to indicate RINS 011 ISSUE 1 7 6 USER FACILITIES R SHIFT 0 PA PERSONAL ATTACK 6 EASY SET A UPARROW amp FIRE DOWNARROW 6 1 Full Setting
8. gineer can clear the log This is achieved by pressing 6 10 Clearing the display after an activation After an alarm condition enter the User code Qo X X This unsets the panel The LEDs will display any activated zones Enter User code again This clears the display RINS 011 ISSUE 1
9. have been displayed the day Led will stop flashing and another function can be selected 6 8 Omitting one or more zones If one or more immediate zones are triggered whilst in exit mode a low pitched error tone will be produced If any zones remain triggered at the end of the exit timer the error tone will continue Key in the User code The display will show the zones which remain triggered Make a note of any triggered zones Key in the user code which will clear the display Check for any obvious reason for these zones to have been activated This may simply be due to a monitored door or window being left open or a pet being left in a protected area If the fault cannot be rectified it is possible to omit faulty zones but this should only be used as a last resort if the building is to be left unoccupied Example Set panel error tone will be heard Wait for the end of the exit timer Error tone is still being produced Key in the user code Triggered zones will be displayed Note triggered zones Key in user code to clear display and error tone then investigate fault s if possible Set panel again then Check the display If the zones are not being triggered exit via normal route or If displays shows zones are as still being triggered then enter 20 now enter the number of the zone to be omitted 1 to 4 then 2 Entry Exit timer will start again then exit building by normal route 6 9 The user if allowed by the en
10. o z O 2 D H 0 z D TT 0 2 p ef ef 4 ZONE PROGRAMMING STATUS LABEL Pyronix P a This product is approved for use in the Residential Commercial and Light Industrial Environment PYRONIX LIMITED ENGINEER NAME ENTRY EXIT TIME SECS BELL OUTPUT SAB SCB BELL TIME MINS PIR LEDs ENABLED DISABLED STATUS KEY ENTRY EXIT A ACCESS IMMEDIATE WPpyronix OMITTED INSTALLATION DATE SERVICE DATE ACTION SERVICE DATE ACTION SERVICE DATE ACTION INSTALLATION COMPANY TEL ADDRESS CONTACT RLBLOSS Issue 3 CE RINS011 ISSUE 1 W Pyronix Pyronix Limited Pyronix House Braithwell Way Hellaby Rotherham S66 8QY ENGLAND Tel 44 0 1709 700100 Fax 44 0 1709 533429 Technical help line UK only 0900 8037 800 This is a premium rate line where calls are charged at 50p per minute email uk sales pyronix com export sales pyronix com marketing pyronix com technical support pyronix com website www pyronix com RINS 011 ISSUE 1 15 14 CONTENTS 1 2 3 o 9o 7 INTRODUCTION FEATURES FUNCTIONALDESCRIPTION 3 1 OPERATINGMODES 3 2 ENTRY EXITMODE ZONES 4 1 ENGINEERPROGRAMMABLE ZONES 4 2 24 HOURZONES CONTRO
11. r will begin If all the Immediate zones are clear then the Entry Exit tone will be heard Leave the protected area by the predetermined Entry Exitroute As you trigger Access zones the tone will change temporarily to a repeated low tone When all the zones are clear the Entry Exit tone will continue again until the end of the time out period The panel will then be set RINS 011 ISSUE 1 12 4 ZONES 4 1 Engineer Programmable Zones Entry Exit Access Immediate Omitted This is a zone which allows limited time access to the premises in order to set or unset the system This is a zone which on setting the panel allows access to the Entry Exit zone However if the panel is set and an Access zone is triggered before an Entry Exit zone then an alarm will be generated immediately This is zone which will when entered create an alarm when the panel is set If a zone is programmed as an Omitted zone by the Engineer then it is ignored by the panel Primarily used for Part set options It also allows the user to continue to use the alarm system even if a fault has been discovered on one or more zones 4 2 24 hour zones Personal Attack Tamper Fire The Fire Zone is intended as an extra feature to the Intruder Alarm system and must Triggering of the Personal Attack P A zone will always be cause a full alarm activation regardless of whether or not the panel is set A tamper zone activation will
12. the panel Enter either of the following Y User Code By using this method maximum volume of the entry exit tone will be heard or a By using this method no sounds will be emitted except for an acknowledge tone at the beginning and the end of the entry exit time 6 2 Part setting the panel Part set 1 eg downstairs only armed 2 1 2 e both will give a silent setting Part set 2 eg upstairs only armed AAD P Enter A e 2 o A v both will give a silent setting 6 3 Unsetting the panel The panel can be unset by entering the building via the entry exit route and then keying the user code 6 4 Activating the Personal Attack Alarm PA To activate the personal attack alarm enter A O 6 5 Activating the Fire Alarm To activate the Fire Alarm enter 2 6 6 Turning On and Off Panel must be day mode Enter R 1 When the chime mode is selected a three note chime will be produced by the internal sounder and any extension speakers when an Entry Exit zone is activated The same key sequence can be used to turn off the chime facility 6 7 Recalling the event log The event log can now be displayed at any time when the Paragon E is unset The event log is displayed by pressing The day led will flash and event information from the latest alarm activation is displayed pressing any key will then show the previous event information When all the four
Download Pdf Manuals
Related Search