DINPAD - Videx
Contents
1. B TAMPER t NO1 COM NC1 NO2 COM2 NC2 Fail Secure Lock 12 24V AC DC 12 24V PTE POWER SUPPLY AC DC GND PB TAMPER NO1 COM NC1 NO2 COM2 NC2 RI VX VIDE The Power to Secure Jumpers Default Backlight closed Reset open 12 24V Acipc GND PB TAMPER S SC 0 S Backlight Reset Permanent Backlight ON OFF Redefine Master Code Backlight jumper Closed Backlight always on Open Backlight active upon keypress Master reset jumper It is possible to redefine and restore the default setting if the Master code is forgotten 000 2578 b o A B Disconnect power Remove master reset jumper Enter the default master code 000 Close master reset jumper Yellow LED switches on Long beep Enter the new master code e g 2578 Reconnect power Press A followed by Beep Beep Beep Beep Yellow LED blinks Press B and the yellow LED switches off LED status Green LED Relay Status Output1 Red LED Relay Status Output2 Orange LED Key press and Menu VIDEX The Power t Adding a User Code Enter Master Code Factory Default 000 Followed by B Yellow LED on Enter lt user number gt 01 99 Up to 99 codes may be added Enter lt new user code gt 1 8 digits Enter lt output number gt to be triggered 1 Relay 2 Transistor 12 both More Yes codes No Yellow LED off Press B to exit programming Del2. XDEX The Power to Secure User Manual These low profile standalone keypads are designed to fita UK single gang electrical back box and are available in 6 different colour finishes They incorporate an easy to follow programming menu allowing up to 99 unique codes and the setting of relay output times The units also include inputs to trigger the relay from a push to exit button Technical Characteristics 80mm Operating Voltage 12 24V DC 15 24V AC e Current consumption Standby 30mA Max 100mA Relays 3A 24V DC 230V AC Relay time 1 99 Seconds or latching 00 Codes 99 User codes 1 8 digits _ Surma IP rating IP40 Housing ABS Mounting UK electrical flush back single gang Wiring Terminal block ao Operating temperature 25 C to 50 C E omm Mounting Note Wall mount box not supplied DINPAD VX VIDE The Power to Secure Power supply Power supply Push to exit Tamper output dry contact Relay 1 Normally open Relay 1 Common Relay 1 Normally closed Terminals aib 12 24V acne GND PB TAMPER AC DC GND DINPAD PB Tamper Tamper NO1 COM1 a a NCI COM2 Backlight ON OFF jumper NC2 Relay 2 Normally open Relay 2 Common Relay 2 Normally closed Master code reset jumper Wiring Fail Safe Lock 12 24V AC DC 12 24V PTE POWER SUPPLY AC DC GND P
3. et up to latch Peto eso ao Ta bie eo 101010101010101 01010101 18107 QA o pa 0OIQIOIQIDIOIOIO 420 cro DO 1 IDE DINPAD I21010191019101010101 01 PEIBIIIG9Iisateaiorane Toa 3 The Power to Secure et Sok ee Pe E ee DINPAD Peto eso ao Ta bie eo 101010101010101 01010101 18107 QA o pa 0OIQIOIQIDIOIOIO 420 cro DO 1 IDE DINPAD I21010191019101010101 01 PEIBIIIG9Iisateaiorane Toa 3 The Power to Secure et Sok ee Pe E ee DINPAD VIDEX The Power to Secure Northern Office Videx Security Ltd Unit 4 7 Chillingham ind Est Newcastle Upon Tyne NE6 2XX The Power to Secure Tel 0870 300 1240 Fax 0191 224 5678 Southern Office 1 Osprey Trinity Park Trinity Way London E4 8TD Fax 0208 523 5825 Technical Support tech videx security com Tel 0191 224 3174 Fax 0191 224 4938 http www videx security com
4. ete All Codes Enter Master Code Factory Default 000 Followed by B Yellow LED on Yellow LED off Press B to exit programming Relay Output Time Enter Master Code Factory Default 000 Followed by B Yellow LED on Enter lt output number gt 1 or 2 Enter lt output time gt 01 99 Enter 00 if latch mode required Yellow LED off Press B to exit programming Delete a User Code Enter Master Code Factory Default 000 Followed by B Yellow LED on Enter lt user number gt 01 99 to delete Yellow LED off Press B to exit programming DINPAD Troubleshooting Keypad does not respond to key presses 1 Check the correct voltage is present on the input terminals 12 24v ac dc Keypad is not accepting default master code 000 1 Perform master code reset Keypad no longer accepts user code 1 Check master code has been changed from the default 2 Check back EMF protection across lock release Keypad accepts user code but no longer releases lock 1 Check the correct relay output is assigned to user code 2 Check push to exit button is normally open 3 Check for continuity across relay contacts when user code is entered 4 Check lock wiring for continuity 5 Check the correct voltage is present on the input terminals 12 24v ac dc Relay triggers and does not return back to its previous state 1 Check relay is not s
Download Pdf Manuals
Related Search