RGBPAR64-02-3W final - SIRS-E
Contents
1. DMX Addrss Setting 4CH 7 CH Master Mode Slave Mode 1 Slave Mode 2 Sound Control Color Control Color Fade ON OFF Displayinglisp it is positive Displayingsid it is reverse Perform Mode Examine Mode Master Mode Special Note Line Termination When longer runs of cable are used you may need to use a terminator on the last unit to avoid erratic behavior A terminator is a 90 120 ohm 1 4 watt resistor which is connected between pins 2 and 3 of a male XLR connector DATA and DATA This unit is inserted in the female XLR connector of the last unit in your daisy chain to terminate the line Using acable terminator will decrease the possibilities of erratic behavior Terminationreducessignalerrors and avoids signaltransmission problemsand interference tis always advisadleto connect a DMX terminal Resistance1200hm 1 4W between PIN2 DMX and PIN3 DMX of the last fixture Figure4 5 Pin XLR DMX Connectors Some manufactures use 5 pin XLR connectors for DATA transmission in place of 3 pin 5 pin XLR fixtures may be implemented in a 3 pin XLR DMX line When inserting standard 5 pin XLR connectors in to a 3 pin linea cable adaptor must be used these adaptors are readily available at most electric stores The chart below details a proper cable conversion 3 Pin XLR to 5 Pin2. LED PAR LINKABLE DMX512 Ta Oe STAND ALONE User Manual Professional Entertainment Equipment General Instructions Please carefully read and understand the instructions in this manual thoroughly before attempting to operate this unit These instructions contain important safety information regarding the use and mainte nance of this unit Please keep this manual with the unit for future reference Main Features Brightness LED Produces many Colors using Green Purple Blue Yellow amp Orange DMX 512 Compatible Master Slave Operation 4 7 DMX Channels Safety Precautions To reduce the risk of electrical shock or fire do not expose this unit rain or moisture Do not spill water or other liquids into or on to your unit Be sure that the local power outlet match that of the required volt age for your unit Do not attempt to operate this unit if the power cord has been frayed or broken Do not attempt to remove or break off the ground prong from the electrical cord This prong is used to reduce the risk of electrical shock and ire in case of an internal short Disconnect from main power before making any type of connection Do not remove the cover under any conditions There are no user serviceable parts inside Never operate this unit when itjs cover is removed Never plug this unit in to a dimmer pack Always be sure to mount this unit in an area that will allow proper vent
3. is for manual color mode There are 7 colors for your choose 3 Press ENTER for FADE this is for manual color shade mode There are 8 speeds for your choose CHnd Channel Changed 1 Tap the MENU button until CHnd is displayed press ENTER Tap the UP or DOWN buttons until your desired setting is displayed press ENTER to confirm Shnd This will let you set unit as a master or slave in a master slave configuration 1 Tap the MENU button until jSLndj is displayed press ENTER Either jNASejjSL 2 jSL 1 2 Tap the UP or DOWN buttons until your desired setting is displayed press ENTER to confirm LED This will turn the LED on or off 1 Tap the MENU button until j LED is displayed press ENTER 2 Either ONj or jOFFjwill now be displayed Press the UP or DOWN buttons to select one or the other 3 Press ENTER and then press and hold the MENU button for at least three seconds to confirm DISP This will jlipj the LED display 1 Tap the MENU button until DISP is displayed press ENTER 2 Either OFF no LED inversion or ONj LED inversion will now be displayed Press the UP or DOWN buttons to select one or the other baLa Tap MENU button until BALA is displayed press ENTER RED GREE BLUE are available to choose 1 Press ENTER for RED this is for Red color mode There is for color adjustment from 0 to 255 2 Press ENTER for GREE this is for Green color mode There is for color adjustment from 0 to 2
4. 55 3 Press ENTER for BLUE this is for Blue color mode There is for color adjustment from 0 to 255 4 Tap MENU button until BALA is displayed press ENTER This is for white color control mode test Tap MENU button until TEST is displayed press ENTER This is for seven colors auto operation Caution Tap MENU button for three seconds to enter your selective Menu mode after you have chosed MENU Mode press ENTER
5. XLR Conversion Conductor 3 Pin XLR Female Owt 5 Pin XLR Male In Ground Shield Pin1 Pin1 data COmpliment signal Pin2 Pin 2 Data True signal Pin3 Pin3 Not Used Do Not Use Not Used Do Not Use On Board System Menu This par can comes with an easy to navigate system menu This next section will detail the functions of each command in the system menu Please read the next section thoroughly To access the main menu press the MENU button Tap the UP or DOWN buttons until you reach function you wish to change When you reach the function you wish to change press the ENTER button When a func tion is selected use the UP or DOWN buttons to change the function settings Once your changes are made press the ENTER button to confirm Ifthe unit remains static for more then eight seconds the fixture will automatically return to its last setting To exit without making any changes press the MENU button Addr DMX Address Setting via control board 1 Tap the MENU button until Addr is displayed press ENTER 2 Xj will now be displayed Xj represents the displayed address Press the UP or DOWN buttons to find your desired address 3 Press ENTER to confirm and then press and hold the MENU button for at least three seconds to assign Shnd Tap MENU button until SHND is displayed press ENTER SOUN COLO FADE will be available to choose 1 Press ENTER for SOUN this is for sound control mode 2 Press ENTER for COLO this
6. ilation Allow about 6 15cm between this device and a wall Do not attempt to operate this unit ifit becomes damaged This unit is intended for indoor use only use of this product out doors voids all warranties During long periods of non use disconnect the unitjs main power Always mount this unit in safe and stable matter Technical Specifications Model NO LED PAR64 3W RGB LEDs 36 3W LED R 12 G 12 B 12 Colors RGB Voltage 100 250v 50 60Hz Dimensions 230 H x 230 W x 310 L mm Weight 5 0Kg Power Consumption 120W Fuse 2Amp GMA Duty Cycle None DMX 4 7 Channels Working Position Any safe secure position Warranty 1lyear 365 days Cleaning Due to fog residue smoke and dust cleaning the internal and external optical lenses must be carried out periodically to optimize light output 1 Use normal glass cleaner and a soft cloth to wipe down the outside casing 2 Clean the external optics with glass cleaner and a soft cloth every 20 days 3 Always be sure to dry all parts completely before plugging the unit back in Cleaning frequency depends on the environment in which the fixture operates i e smoke fog residue dust dew Trouble Shooting Listed below are a few common problems the user may encounter with solutions Unit not responding to DMX Check that the DMX cables are connected properly and are wired correctly pin 3 is hot on some other DMX devices pin 2 may be hot Also chec
7. k that all cables are connected to the right connectors it does matter which way the inputs and outputs are connected Unit does not respond to sound Quiet or high pitched sounds will not activate the unit If problems are not resolved contact your dealer for service Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them paying particular attention to cords at plugs convenience recep tacles and the point where they exit from the appliance Cleaning The fixture should be cleaned only as recommended by the manufacturer See page 10 for cleaning details Heat The appliance should be situated away from heat sources such as radiators heat registers stoves or other appliances in cluding amplifiers that produce heat The fixture should be serviced by qualified service personnel when A The power supply cord or the plug has been damaged B Objects have fallen or liquid has been spilled into the C The appliance has been exposed to rain or water D The appliance does not appear to operate normally or exhibit marked change in performance DMX 512 DMX is short for Digital Multiplex This is a universal pro tocol used as a form of communication between intelligent fixtures and controllers A DMX controller sends DMX data instructions from the controller to the fixture DMX data is sent as serial data that trav els from fixture to fixture via
8. o remember that DMX cable must be daisy chained and can not be split Notice Be sure to follow figures two and three when making your own cables Do not use the ground lug on the XLR connector Do not connect the cablejs shield conductor to the ground plug or allow the shield conductor to come in contact with the XLRjs outer casing Grounding the shield could cause a short circuit and erratic behavior DVK512 QUT 3 AN XLR OIMN DNK DNVK Figure1 Figure2 XLR Pin Configuration pin1 Ground pin2 Data Compliment negative pin3 Data true positive System Menu DMX 4Channels amp Functions 1CH 0 Closed 1 255 R 2CH 0 Closed 1 255 G 0 Closed een 1 255 B 0 7 Closed ACH 8 200 Adjust general brightness 201 247 Strobe effect is from slow to fast 248 255 Full brightness DMX 7 Channels amp Functions 1CH 0 Closed 1 255 R 2CH 0 Closed 1 255 G 3CH 0 Closed 1 255 B 4CH 0 Closed 1 255 AdDjust general brightness 5CH 0 9 Full brightness 10 248 Color change 249 255 Full brightness 6CH 0 9 Closed 10 255 Strobe effect is from slow to fast 7CH 0 127 Closed 128 255 Sound control MENU
9. the DATA IN and DATA OUT XLR terminals located on all DMX fixtures most controllers only have a DATA jOUTj terminal DMX Linking DMX isa language allowing all makes and models of different manufactures to be linked together and operate from a single controller as long as all fixtures and the controller are DMX com pliant To ensure proper DMX data transmission when using several DMX fixtures try to use the shortest cable path possible The order in which fixtures are connected in a DMX line does not influence the DMX addressing For example a fixture assigned a DMX address of 1 may be placed anywhere in a DMX line at the beginning at the end or anywhere in the middle When a fixture is assigned a DMX address of 1 the DMX controller knows to send DATA assigned to address 1 to that unit no matter where it is located in the DMX chain Data Cable DMX Cable Requirements For DMX and Master Slave Operation The PAR CAN can be controlled via DMX 512 protocol It isa 4 7 channel DMX unit The DMX address is set below the dome of this PAR light Your unit and your DMX controller require a standard 3 pin XLR connector for data input and data output Figure 1 If you are making your own cables be sure to use standard two conductor shielded cable This cable may be purchased at almost all pro sound and lighting stores Your cables should be made with a male and female XLR connector on either end of the cable Als
Download Pdf Manuals
Related Search