Home

DS-2CE56D1T-IT3

image

Contents

1. SMART Select to turn on off the INFRARED_LAMP and to set the Smart IR level from 1to 16 As shown in Figure 3 4 DAY NIGHT MODE SMART INFRARED OFF SMART IR O 5 RETURN Figure 3 4 DAY NIGHT 3 2 4 VIDEO SETTING Contrast Contrast enhances the difference in color and light between parts of an image You can set the value from 1 to 10 Sharpness Sharpness determines the amount of detail that an imaging system can reproduce You can set the value from 1 to 10 Saturation You can set the saturation level of the image The value is from O to 10 DNR DNR decreases the noise effect especially in low light conditions and delivers more accurate and sharp image quality You can set the value from Oto 7 Mirror You can set the Mirror status as H V HV or OFF 3 2 5 Reset Reset all the settings to the default 3 2 6 EXIT Exit and Save amp exit are selectable 3 2 7 SAVE EXIT Move the cursor to SAVE amp Exit and press OK to save the settings and exit the menu
2. equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense FCC Conditions This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference 2 This device must accept any interference received including interference that may cause undesired operation EU Conformity Statement i This product and if applicable the supplied accessories too are marked swith CE and comply therefore with the applicable harmonized European standards listed under the Low Voltage Directive 2006 95 EC the EMC Directive 2004 108 EC the RoHS Directive 2011 65 EU 2012 19 EU WEEE directive Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Ee Union For proper recycling return this product to your local supplier upon the purchase of equivalent new equipment or dispose of it at designated collection points For more information see www recyclethis info 2006 66 EC battery directive This product contains a battery that cannot be disposed of as unsorted municipal waste in the European Union See the product documentation for specific battery information The battery is marked with this symbol which may include lettering to indicate cadmium Cd lead Pb or mercury Hg For proper recycling
3. return the battery to your supplier or to a designated collection point For more information see www recyclethis info 1 Introduction 1 1 Product Features This series of camera adopts new generation sensor with high sensitivity and advanced circuit design technology It features high resolution low image distortion and low noise etc which makes it suitable for surveillance system and image processing system High performance CMOS sensor and high resolution bring high quality image Low illumination OSD menu parameters are configurable Support auto white balance auto gain control eSupport image effect adjustment Unit transmission control Advanced 3 axis design meets different installation requirements 1 2 Overview 1 2 1 Overview of Type Camera Side Opening Ze Z Mounting Base Gea LLA HD Video Power Cable 1 2 2 Overview of Typel Camera HD Video Cable Power Cable Mounting Base 1 2 3 Overview of Type Camera Enclosure Mounting Base 2 Installation Before you start Please make sure that the device in the package isin good condition and all the assembly parts are included Make sure that all the related equipment is power off during the installation Check the specification of the products for the installation environment Check whether the power supply is matched with your power output to avoid damage
4. 5 The Drill Template 2 Fix the mounting base to the ceiling with the supplied screws RUHHA Figure 2 6 Fix the Mounting Base and Camera 3 Route the cables to the cable hole and connect corresponding power cable and video cable 4 Secure the camera to the mounting base 5 Fix the enclosure to camera 6 Attach the trim ring to the camera and rotate it clockwise to secure the camera loosely A Figure 2 7 3 axis Adjustment 7 Adjust the camera according to the figure 2 7 to get an optimum angle and tighten the trim ring 2 3 Installation of Type Camera Steps 1 Drill the screw holes and the cable hole on the ceiling according to the supplied drill template Figure 2 8 The Drill Template 2 Fix the mounting base to the ceiling with the supplied screws Wi Figure 2 9 Fix the Mounting Base and Camera 3 Route the cables to the cable hole and connect corresponding power cable and video cable 4 Secure the camera to the mounting base 5 Adjust the camera according to the figure below to get an optimum angle 0 360 Figure 2 10 3 axis Adjustment 3 Menu Operation Menu FORMAT SETUP VIDEO WB DAY NIGHT SETTING RESET EXIT SAVE EXIT MODE CONTRAST SMART IR SATURATION DNR wn BRIGHTNESS EXPOSURE MODE MIRROR Figure 3 1 Main Menu kK EE With a coaxial camera controller purchase separately o
5. HIKVISION TURBO HD TVI Turret Camera User Manual UD 6L0201D1933A01 Thank you for purchasing our product If there are any questions or requests please do not hesitate to contact the dealer This manual applies to Typel DS 2CE56D1T IRM Typell DS 2CE56D1T IT3 DS 2CE56D1T IR Type lll DS 2CE56D1T IT1 This manual may contain several technical incorrect places or printing errors and the content is subject to change without notice The updates will be added to the new version of this manual We will readily improve or update the products or procedures described in the manual Privacy Notice Surveillance laws vary by jurisdiction Check all relevant laws in your jurisdiction before using this product for surveillance purposes to ensure that your use of this product conforms Please refer to the product specification for camera parameters and functions 0100001050409 Regulatory Information FCC Information FCC compliance This equipment has been tested and found to comply with the limits for a digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this
6. Please make sure the wall is strong enough to withstand three times the weight of the camera and the mounting elf the wall is the cement wall you need to insert expansion screws before you install the camera If the wallis the wooden wall you can use self tapping screw to secure the camera if the product does not function properly please contact your dealer or the nearest service center Do not disassemble the camera for repair or maintenance by yourself 2 1 Installation of Type Camera Steps 1 Drillthe screw holes according to the drill template Drill Template e Screw hole All for Mounting Base Screw hole Figure 2 1 The Drill Template 2 Screw the clip plate onto the mounting base loosely Clip Plate Figure 2 2 Screw the Clip Plate 3 Fix the mounting base to the ceiling with the supplied screws 4 Route the cables to the cable hole and connect the corresponding power cable and video cable 5 Pull out the clip plate and secure the camera with the trim ring tothe mounting base 6 Push the clip plate in and tighten the lock screw to secure the trim ring Clip Plate Figure 2 3 Fixthe the Camera 6 Adjust the camera according to the figure below to get an optimum angle Figure 2 4 3 axis Adjustment 2 2 Installation of Type Il Camera Steps 1 Drill the screw holes and the cable hole on the ceiling according to the supplied drill template Figure 2
7. r calling the preset No 95 you can select the menu and adjust the camera parameters 3 1 FORMAT You can set the format as PAL NTSC 3 2 SET UP Move the cursor to SET UP and press menu button to enter the SET UP sub menu 3 2 1 AE Move the cursor to AE and you can adjust the image brightness by the BRIGHTNESS EXPOSURE MODE and AGC Brightness Brightness refers to the brightness of the image Exposure Mode Move the cursor to Exposure Mode you can select the exposure mode between Globe and BLC When BLC is selected as the exposure mode the level of BLC mode can be adjusted as shown in the Figure 3 2 EXPOSURE WB 1 BRIGHTNESS 45 MODE MWB 2 EXPOSURE MODE 4BLC R GIAN 1 10 LEVEL 45 gt B GAIN 1 10 3 AGC 4 MIDDLE gt RETURN ai 4 RETURN Figure 3 3 WB Figure 3 2 EXPOSURE AGC AGC optimizes the clarity of image in poor light scene AGC level can be set as OFF LOW MIDDLE and HIGH 3 2 2 WB Move the cursor to WB and you can set White Balance mode as AWB and MWB in this menu AWB white balance is being adjusted automatically MWB Set the R GAIN B GAIN value from 1 to 10 As shown in Figure 3 3 3 2 3 DAY amp NIGHT Move the cursor to DAY amp NIGHT and select COLOR B W or SMART as the DAY amp NIGHT mode COLOR The image is colored in day mode all the time B W The image is black amp white all the time and the IR LED turns on in the low light conditions

Download Pdf Manuals

image

Related Search

DS 2CE56D1T IT3 ds-2ce56d1t-it3

Related Contents

Ryobi Outdoor 890r User's Manual  dc-oc-12u  35) p. 66. This is embarassing but I`m not sure I`ve ever understood  LIBRETTO ISTRUZIONI  Toshiba dynadock V 3.0  製品安全データシート  PAVIFER 100 - Ferro-Sport al Agua 7005    EWD2 User Manual (updated 2014.07.09)  CT-414WR 取扱説明書ダウンロード  

Copyright © All rights reserved.
Failed to retrieve file