User`s Manual
Contents
1. T ee SIE gai pi Fi pi F I F f j EN I Figure 2 6 Place Document on the Scanner 2 7 2 6 ADF SCANNING Standard paper size can be scanned automatically using the ADF Refer to Figure 2 7 I To prevent occasional paper jam when automatically feeding multiple documents fan the paper before loading ii Lift the balance wire and place the documents to be scanned onto the ADF paper chute face down with the leading edge in the auto feeder entrance Let the balance wire rest on the top of the documents ili Adjust the left and right guides so that they are snug against the sides of the documents Auto Feeder Hole Left Guide Balance Wire Document blank side ADF Paper Chute Right Guide Figure 2 7 Use ADF to Load Multiple Documents 2 8 2 7 CONNECTING THE CABLE I Turning the Power Off Depress the side marked O to turn the power off Connect the power cable and SCSI signal cable as shown in Figure 2 8 and Figure 2 9 li Turning the Power On Depress the side marked I to turn the power on The POWER LED will light If not please check the power source iii SCSI Termination The Fujitsu ScanPartner 620C comes complete with a built in SCSI terminator If the Scanner is the last device in a SCSI chain the terminator should be switched on If the Scanner is not the last device the terminator should be off The terminator on off switch is located on the2. Using a suitable tool turn the selector switch until the arrow points to the desired ID number 2 3 SCSI ID Selector SCSI Termination Switch Figure 2 3 Adjusting the SCSI ID setting 2 4 2 3 ADF PAPER CHUTE I Raise the right side of the paper chute to about 45 degrees ii Pull down the wire leg from under the paper chute iii Insert the wire leg into the grips on the document cover iv Pull out the paper chute extension to the length you want ADF Paper Chute Paper Chute Extension Document Cover Figure 2 4 Setting the ADF Paper Chute 2 5 2 4 ADF OUTPUT TRAY Hold the output paper tray some 30 degrees aslant as shown in Figure 2 5 Insert the three protrusions on the output paper tray to the three slots on the ADF Release the paper tray gently Make sure the tray is firmly attached to the ADF Pull out the output paper tray extension wire to the desired length Protrusions ADF Output Tray Extension Figure 2 5 Install the ADF Output Paper Tray 2 6 2 5 DOCUMENT LOADING For flatbed scanning Documents that can not be scanned using the ADF can be placed on the flatbed for scanning See Figure 2 6 I Place the document to be scanned onto the document glass face down ii Position the document so that the upper right corner is aligned with the reference mark Document Cover Reference Mark Original Document Glass Reference Frame
3. mark 2 7 refit the shipping bracket 2 3 S Scanner packing 1 2 SCSI chain 2 3 SCSI ID selector 2 3 SCSI Termination 2 9 shipping bracket 2 1 shipping position 2 3 U use position 2 1 2 3
4. Coated paper e Carbonless paper Paper narrower than 3 5 or wider than 8 5 e Items other than papers such as cloth metal or OHP film Notched paper Paper with an odd non rectangular shape Very thin paper Please use the flatbed to scan documents that cannot be fed by the ADF Scanner Type Scanning Mode Optical Resolution Light Source ADF Capacity ADF Scanning Speed Scanning Document Size Max Interface Power Requirement Power Consumption Humidity Operation Temperature Storage Temperature Dimension Weight 5 1 SCANPARTNER 620C SPECIFICATIONS 1 pass colour Flatbed with ADF built in 36 bit colour 12 bit Grey Scale Line Art Halftone Error Diffusion single bit 600 x 1200 dpi in a dpi increments Cold Cathode fluorescent lamp 50 pages 20 PPM 200dpi B W mode ADF ADF mode 8 5 x 14 Flatbed mode 8 5 x 11 69 SCSI 2 100 240 Vac 50 60Hz 30 watts 20 to 80 10 to 35 20 to 60 570 x 350 x 166 mm WxDxH Appropriate 26 5 lbs 12 kg 5 2 A ADF cover 4 3 ADF Scanning 2 8 B balance wire 2 8 C Cleaning the ADF 3 1 Cleaning the Glass 3 3 Connecting the Cable 2 9 D document cover 2 5 Document Loading 2 7 O output paper tray 2 6 output paper tray extension 2 6 Index P paper chute 2 5 paper chute extension 2 5 paper jam 2 8 4 3 POWER LED 2 9 protrusions 2 6 R READY LED 4 1 reference
5. FUJITSU ScanPartner 620C Image Scanner User s Manual Doc No 250 0062 0 Ver 1 0 FCC Radio Frequency Interference Statement This equipment has been tested and found to comply with the limits for a class B digital device pursuant to Part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communication However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help CAUTION Any changes or modifications not expressly approved by the manufacture of this device could void the user s authority to operate the equipment Table of Contents EL eee EEE SEE EEE ETEN 1 1 JE EE Ne PRESSE EEE ERE ET 2 1 2 Omer ING EN tra
6. back of the Scanner to the left of the SCSI cable connectors Host PC SCSI Device Terminator Off Terminator On 2 9 Power Switch SCSI Port Power Cable SCSI Cable Connector To PC SCSI Port Figure 2 9 ScanPartner 620C SCSI Cable Connection 2 10 3 MAINTENANCE 3 1 CLEANING THE ADF Your Scanner is designed to be maintenance free However it still needs to be cleaned occasionally to ensure optimum image quality and performance From time to time the pad assembly and feeding rollers may become contaminated with ink toner particles or paper dust In this case the scanner may not feed documents smoothly or several documents may feed at once If this occurs please follow the cleaning procedures to return your Scanner to its original state The cleaning procedures Figure 3 1 I Moisten a cotton swab with isoprophyl alcohol 95 Cleaner kits are available from Fujitsu ii Open the ADF unit by depressing the button in front of the ADF unit carefully open the ADF to the left Wipe the feeding rollers by moving the swab from side to side Rotate the rollers forward with your finger and repeat the above cleaning procedures until the rollers are clean Be careful not to snag or damage the pick springs iii Wipe the pad in the direction from top to bottom Be careful not to hook the pick springs iv Close the ADF unit Your Scanner is now ready for use 3 1 ADF Pad Modu
7. cer none one enemas 2 1 2 1 1 REMOVING THE SHIPPING BRACKET ernnnnnnnnnnnnrvnrnnnvernnerernnerernnerernnerernnrrennne 2 1 2 1 2 REFITTING THE SHIPPING BRACKET i enrnnnnnnvnnnnnvnrnnnvernnerernnerernnerernnerennnrrennne 2 3 2 SSN EE ENE 2 3 2 MT ER EP 2 5 AF TN 2 6 25 DOCUMENT LOADING Hadde NERE 2 7 FN 2 8 2 TENNE INTE BER 2 9 GE EE 3 1 3 1 CLEANING THE ND ee eee eee 3 1 3 2 CLEANING THE GLASS Luussmmmmnenaisem ej njkersnmnonapnepandgdse 3 3 3 3 REPLACING THE ADF SNAP IN PAD MODULE aamnvnnnnnnnnnnnnnnrnnnnnnnrnnnnnnrnnnennnrnnenennnnnnn 3 4 Je ee RE EEE EEE 4 1 2 OUES HON AND ANSWER NR 4 1 22 PAPER JONE Ps 4 3 eee ernn 5 1 5 1 SCANPARTNER 620C SPECIFICATIONS cee tees eee e eee ea eee ee sana eeeeaaeeeeseaaaeees 5 2 INDEX iii 1 INTRODUCTION Congratulations on your purchase of Fujitsu ScanPartner 620C Scanner Before you install and operate the new Scanner please take a few minutes to read through this manual It provides you with the proper instructions on how to unpack install operate and maintain the Scanner Figure 1 1 shows how the Scanner is packed You can check all items against your checklist included with your Scanner Power Cable Signal Cable _ Optional Package Driver Kit Output Paper Rack Scanner Body WS PL GL 12 Form Fight Carton Figure 1 1 Scanner packing 2 INSTALLATION Please unpack the Scanner carefully and check the contents against the ch
8. ecklist If any items are missing or damaged please contact your authorized local dealer immediately Precautions Keep the Scanner out of direct sunlight Direct exposure to the sun or excessive heat may cause damage to the unit Do not install the Scanner in a humid or dusty place Be sure to use the proper AC power source e Place the Scanner securely on an even flat surface Tilted or uneven surfaces may cause mechanical or paper feeding problems Retain the Scanner box and packing materials for shipping purposes 2 1 SHIPPING BRACKET The Scanner has a bracket that locks the carrier mechanism for transportation purposes This bracket must be put into the use position before using the Scanner If the power is turned on before the bracket has been removed the PAPER JAM light will turn on Before proceeding turn the power off disconnect all cables and follow the instructions below to remove the shipping bracket 2 1 1 REMOVING THE SHIPPING BRACKET i Carefully place the Scanner in an upright position on its front il Using a suitable screwdriver remove the screw and pull out the shipping bracket See Figure 2 1 iii Put the shipping bracket into the use position with the short side extending into the Scanner base and secure it with the screw See Figure 2 2 iv Carefully place the Scanner back into its normal position 2 1 c __ Shipping Position Figure 2 1 Rem
9. le Feeding Roller Figure 3 1 Opening the ADF unit and Document Cover 3 2 CLEANING THE GLASS The procedures Soak a cotton swab with some isoprophy alcohol 95 Open the ADF unit and document cover as shown in Figure 6 2 Wipe the glass of flatbed area and ADF area by moving the swab from side to side Close the ADF unit and document cover Your Scanner is now ready for use Figure 3 2 The Cleaning Area 3 3 3 3 REPLACING THE ADF SNAP IN PAD MODULE After scanning approximately 150 000 pages through the ADF the pad spring may be worn out and you may experience problems with document feeding In this case it is highly recommended to replace the pad module with a new one For ordering the pad module please consult your nearest dealer and follow the procedure below to replace it Disassembling Procedure 1 Open the ADF front cover by depressing the ADF release button 2 Remove the ADF snap in pad module by pulling out the upper part of the pad clamp as shown in Figure 3 3 Upper Part of ADF Pad Clamp r 27 ME ADF Unit ADF Release Button Figure 3 3 Remove the pad module 3 4 Assembling Procedure 1 Take out the ADF pad module from the box 2 Hold the upper part of the pad clamp and place it gently to the pad holder as shown in Figure 3 4 Upper Part of the Pad Clamp ADF Pad Module Figure 3 4 Installing the pad module 3 5 4 TROUBLESHOOTING The Scanner will automatically
10. or it scans back and forth Answer Please choose lower speed from the TWAIN user interface for low speed PC Question The scanned image always comes out to be too dark Answer a Use your application to modify the Gamma setting to 2 2 and 1 8 for your printer and monitor respectively b Use Brightness setting from the TWAIN user interface to get a brighter image Question The Scanner works well otherwise but for the line art the lines of which seem much thicker than those of the original Answer Use the Brightness or Threshold setting to adjust the line art image 4 2 PAPER JAM IN THE ADF In the event of paper jam please follow the procedures below I Press the ADF Release Button at the front left of the Scanner as shown in Figure 4 1 The ADF cover will be released il Open the ADF cover to the full open position as shown in Figure 4 2 ili Pull the paper out of the ADF unit carefully ADF Cover ADF Release Button n Teee PE ee EE Figure 4 1 ADF Paper Jam Opening the ADF 4 3 ADF Unit ADF Paper Chute Document Figure 4 2 ADF Paper Jam Removing the Paper 4 4 5 SPECIFICATIONS All specifications are subject to change without notice The following can not be properly fed by ADF Paper with clip or staple attached Paper with ink not totally dry Paper with inconsistent thickness such as envelopes Paper with wrinkles curls folds or tears e Tracing paper e
11. oving the Shipping Bracket dl Use Position T Figure 2 2 Securing the Shipping Bracket 2 1 2 REFITTING THE SHIPPING BRACKET Whenever you need to move the Scanner to a new location it is advisable to refit the shipping bracket to avoid causing damage to the Scanners internal mechanism Please follow the instructions below to refit the shipping bracket i Turn off the Scanner power at the power on off switch ii Open the document cover iii Turn off the Scanner Note For steps iv to vi please refer to Figure 2 1 and 2 2 iv Carefully place the Scanner in an upright position on its front side v Use a suitable screwdriver to remove the screw holding the shipping bracket in the use position vi Put the shipping bracket into the shipping position with the long side extending into the Scanner base Secure it with the screw vii Carefully place the Scanner back into its normal position 2 2 SCSI INTERFACE DEVICE ID When you have several devices on a SCSI chain you may need to adjust the SCSI ID selector setting located on the back of the Scanner This setting assigns a specific device ID to the Scanner If the assignment conflicts with an existing SCSI device please select a new ID See Figure 2 3 Note The factory setting for Scanner is ID 6 Usually ID 0 is assigned to an internal hard disk drive and ID 7 to SCSI adapter or host ID 8 and 9 are not in actual use
12. perform a simple self test each time it is turned on This will help spot major system errors in the Scanner itself When the test is initiated the READY LED is flashing When the test is completed if no error occur the READY LED is steadily on If you have problems with the operation of your Scanner please check the following troubleshooting hints 4 1 QUESTION AND ANSWER Question Answer Question Answer Question Answer The LED indicates that the Scanner is ready but the Scanner does not respond to the scan command form the host computer a Please check the signal cable is firmly seated and invoke the scan command again If there is still no response please reset the Scanner by turning it off and then on again and reboot your host computer as well b Check if the driver is correctly installed You can use the DIAG EXE file in Fujitsu Driver Kit to check this out c Try to select another port memory Paper becomes jammed during scanning a Open the ADF unit b Pull out the jammed paper carefully c Close the ADF unit More than one sheet of paper were fed into the Scanner a Open ADF unit b Remove the multi fed sheets of paper c Close the ADF unit d Flatten the corners and edges loosen the paper before reloading it in the paper guide e Check the feeding roller condition and do the cleaning if necessary See Chapter 3 4 1 Question Answer Question An
13. swer Question Answer Question Answer Paper becomes skewed in the Scanner a Check the feeding roller condition do the cleaning if necessary See Section 3 1 b Use the paper guide when feeding the paper When power on the Scanner it makes noises and will not stand ready There are two possibilities a You forgot to remove the shipping retainer from the Scanner Please remove the shipping retainer first b You did not place the Scanner on a flat desktop surface This may cause the scanner to function improperly When I power on the Scanner the lamp does not light The possibilities are as follows a The lamp is out of order In that case contact your authorized local dealer to change the lamp The life time of the lamp is about 5000 hours b The fuse on main board of the Scanner is burned Check the main board of the Scanner If the fuse is burned put in a new fuse that is 250V 2A c If the fuse burns again after the changing it means the inverter of the lamp is burned Contact your authorized local dealer to replace the inverter Getting image from the Scanner is not a problem but when scanning the Scanner or system will often crash Please check a If the cable is firmly seated b Only two SCSI terminators can be connected to your SCSI daisy chain One is at the end of the SCSI device another is already in your host adapter Question While scanning the Scanner often makes noises
Download Pdf Manuals
Related Search