movilino
Contents
1. power unit O battery pack AAT Ideen bewegen mehr 2 2 1 Control unit O safety chip for the engine immobiliser O ON OFF switch O rocker switch forward backward speed control 2 2 2 Overview O control unit tightening knob for the handles height adjustment O tightening knob for the column O light emitting diode O drive wheels O small wheels O lower rod O recessed handle O upper rod socket for the power cable handle movilino AAT Ideen bewegen mehr movilino 2 3 Technical data heigth min 926 mm max 1128 mm measurements width handle 636 mm power unit 230 mm depth handle 233 mm power unit 307 5 mm power unit 10 5 kg handle unit 2 5 kg battery pack 9 0 kg weight power cable 220 g bag for batteries plus velcro straps 180 g charger 740 g total weight 23 14 kg limits for mounting the device on a wheelchair seat width of 32 cm or more max approved total weight 170 kg person wheelchair movilino continually adjustable speed 6 km h forward 3 km h backward running in slowing period approximately 10 seconds braking and climbing capacity up to 18 capacity with one battery charge over 21 km batteries 2x12V 16 Ah direct current motor 24 V 200 W storing and operating temperature 20 C to 60 C 10 C to 50 C the device s A weighted noise level lies t2. 2 Putthe quick pin all the way into the drilled hole of one of the upper brackets on the wheelchair O and release the quick pin 3 Now take the other quick pin and put it into the other bracket on the wheelchair as described in point 2 Only by using quick pins a strong connection between movilino and wheel chair is secured EF The movilino may only be operated if the quick pins are securely lo cked in the wheelchair s brackets 5 The wheelchair s wheels may not be removed when you operate the movilino 3 3 Attach the battery pack The bag for the battery pack is located under the seat of the wheelchair Sim ply slide the battery pack into its bag and fix it with a velcro strip 16 movilino AAT Ideen bewegen mehr movilino Afterwards you can insert the plug of the power cable into the socket on the battery pack 5 Please make sure that the power cable s plug is dry and clean Plug the power cable s plug into the socket on the movilino 5 Please make sure that the power cable s plug is dry and clean If the device is already attached to the movilino as described in chapter 3 2 you are ready to go 3 4 Detach the battery pack To detach the movilino from your wheelchair please repeat the process in re versed order see chapter 3 2 3 chapter 3 3 EF First remove the power cable from its socket on the movilino 5 Please make sure that the anti tilt support is also removed 3 5 Adjust
3. 31 AAT Ideen bewegen mehr 8 3 Battery pack The battery pack s sealed lead acid batteries should be recharged after each use They are air tight maintenance free rechargeable and of excellent qua lity The battery pack undergoes a so called self discharge therefore you should connect your battery pack whenever possible to a charger The charging au tomatism which switches from charging the battery to retaining the charge when it is full kicks in and keeps the battery from overcharging If you take good care of your battery pack by recharging it regularly you pro long its durability The movilino s electronics constantly check the battery s charge and thus prevent a total discharge if used adequately 5 Avoid a total discharge of the battery pack Recharge it after each partial discharge i e after each use of the movilino EF Charging your batteries is taking good care of them If your battery pack has not reached its full capacity it is possible that with a new battery pack it takes a few charging discharging cycles to build up the full capacity If fully charged batteries empty faster than usual they are probably used up In such case have your batteries checked by your local dealer and exchan ged if necessary E f the movilino is at a standstill for some time please connect it to the charger to retain the charge This does not damage the sealed lead acid batteries on the contrary it increases their du
4. 5 Before using the charger please read and follow all instructions and warning notes included with the charger EF Exclusively use the AAT charger to charge the batteries Check the charger regularly and protect it from oils grease aggressi ve cleaning agents thinners and or damage by sharp edges etc 5 Repairs and service check ups may only be performed by AAT Alber Antriebstechnik GmbH or their authorized personnel 5 Please do not disassemble or modify the charger 5 Please make sure that the charger is not exposed to dampness or hu midity while charging the batteries 5 Never touch the plug with moist hands 30 movilino AAT Ideen bewegen mehr movilino 8 2 2 Voltage converter for your vehicle The voltage converter does not need particular care or maintenance Never theless check your voltage converter regularly and protect it from oil grease aggressive cleaners diluting agents and or damage due to sharp edges etc EF Before using the voltage converter please read and follow all in structions and warning notes printed on the voltage converter EF Exclusively use the AAT Alber Antriebstechnik GmbH voltage con verter 5 Check the voltage converter regularly and protect it from oil grease aggressive cleaning agents thinners and or damage by sharp edges etc 5 Repairs and service check ups may only be performed by AAT Alber Antriebstechnik GmbH or their authorized personnel
5. Please make sure that both wheels are exchanged 4 5 Lifting capacity The maximum total weight of 170 kg is composed of the weight of the person to be transported plus the weight of the wheel chair and the movilino This weight may under no circumstances be excee ded EF Please use the movilino exclusively to transport people It is strictly prohibited to transport goods with the device 4 6 Care and maintenance Please make sure that you charge the batte ry pack after each use of the movilino If the movilino is not in operation please turn off the device If the working elements of the device block turn the movilino off immediate ly 5 Please note the wear limit of the powered wheels see chapter 4 4 EF Repairs may be done by authorized dealers or the manufacturer only Please exclusively use AAT Alber parts and accessories Please note the extensive care and maintenance instructions in chapter 8 4 7 Condition of paths walkways etc You should avoid operating the device on unfortified grounds sand mud loose gravel ice or snow as well as crossing deep puddles maximum depth approximately 2 5 cm with it Please avoid using the movilino in the rain ice snow or general wet condi tions because then the wheels grip on the ground is reduced There is an in creased danger of slipping and sliding Please adjust your driving style accordingly 4 7 1 Environmental conditions Although the movilino has been tested
6. The ON OFF switch 6 is located on the control unit standard version right handle It is possible to supply you with a left handed control for additional charge After turning the movilino on with the ON OFF switch the device s electro nics perform an automatic safety check If there is no malfunction the hub motor automatically moves downward This process lasts approximately 5 to 10 seconds Once the hub motor is completely lowered you hear an acoustic signal EF The movilino is equipped with a turn off feature if the device is on and has not been used for 5 minutes the turn off feature switches the movilino off automatically Insuch case you can only use the mo vilino again by pressing the ON OFF switch If the device is at a standstill for a longer period of time please turn it off The hub motor automatically moves back up If it moves back all the way you hear an acoustic signal once again At this point you can push the wheel chair manually 6 1 2 Speed control The speed control allows you to pre select speed EF Turn the speed control counter clockwise all the way for minimum speed You must begin with minimum speed when you use the movilino for the first time 6 1 3 Safety chip for the engine immobiliser The movilino only works if you insert the the safety chip for the engine immo biliser O into its proper slot Please make sure that the chip snaps in becau se only then the movilino works properly If you do n
7. batteries in your vehicle By means of the voltage voltage converter you may even charge your battery pack while driving your car First remove the power cable Then fully insert the plug of the charger into the charging socket on the battery pack Then connect the charger to the vol tage voltage converter Finally you plug the voltage converter into the cigaret te lighter Afterwards you first pull the voltage converter s plug from the cigarette lighter before you disconnect it from the charger Signals of the charger and the voltage converter voltage converter beeping 12 V supply is low charger LED orange batteries are being charged charger LED green batteries are fully charged maintenance mode 33 AAT Ideen bewegen mehr 8 4 Fuse The battery pack has two fuses each 40A located in a special compartment O Once the lower fuse is burnt out replace it by the upper extra fuse If a change of fuses is necessary put a pin in the opening O on the side of the battery pack This unlocks the drawer so you can pull it out 5 You may not mend or by pass a defect fuse Always replace it with an identical one of the same amperage EF AAT Alber Antriebstechnik GmbH could offer you replacements of the fuses 5 Before you exchange the fuses please remove the charger from the battery pack EF Should your fuses burn out frequently please contact AAT Alber Antriebstechnik GmbH or your autho
8. of the hou sing 1 1 How to use this user s manual The user s manual is part of the delivery package and instruct you step by step about the safe and adequate use of the movilino Operating the movilino takes a certain skill Please read this user s manual carefully and particularly take note of the sa fety Instructions before you use the movilino for the first time After reading please store this user s manual at an appropriate place for furt her reference 1 2 Instruction In the interest of your safety the movilino a only be operated by trained per sonnel Instruction on how to operate the device is part of the delivery package and takes place with your authorized dealer or an AAT representative Please read this user s manual carefully and particularly take note of the sa fety Instructions before you use the movilino for the first time 1 3 Care and maintenance One of the most important aspects concerning the maintenance of the movi lino is charging the seal lead acid batteries They are part of the battery pack and must be charged every time after using the device Other than that your movilino does not need much care or maintenance More extensive instructions you find in chapter 8 1 4 Warranty and liability For damage that was caused by inadequate use disregarding this manual we assume no liability whatsoever Please read chapter 9 for more detailed in formation concerning warranty and liability 2 Descripti
9. the handle Please adjust the handle to the appropriate and for the operator comfortable position Release the tightening knob O by turning counter clockwise Pull out the handle to the appropriate height O maximum shoulder height Then re tighten the tightening knob EF Please always make sure that the tightening knob is secure 5 Please adjust the handle exactly according to instructions see pic ture Attention avoid bruising at the nut s opening 17 AAT Ideen bewegen mehr 3 6 Anti tilt support You may operate the movilino only with installed anti tilt support If your wheelchair does not have a tilt support which Is standard with most wheelchair manufacturers we can equip your wheelchair with the necessary anti tilt Support as an optional accessory of the movilino Holding devices for our anti tilt support are already mounted on the brackets of the movilino 3 6 1 Attaching and removing the anti tilt support Brackets with holding device for the anti tilt support Slide the tilt support amp all the way into the holding device O on the movili no Pay attention on the label at the anti tilt support Lock it with the quick pin Push the quick pin into the drilling on the holding device while you press the unlocking button at the top of the quick pin When the quick pin is inserted all the way you release the unlocking button on the quick pin EF Please check whether the quick pins are tightly
10. 12 V electrical system This voltage converter transforms 12 V 24 V direct current D C into 230 V alternating current A C The plug of the voltage converter O is plugged into the cigarette lighter in your car or into the socket of the supply system The automatic charger s 230 V connector is plugged into the socket of the converter 29 AAT Ideen bewegen mehr 8 Care maintenance and recycling To insure the movilino s safe and proper functioning we recommend a safety check done on the device every two years even though there might not be any outer damage or malfunction evident EF For safety reasons this safety check or repairs of any sort may only be performed by AAT Alber Antriebstechnik The device itself does not call for particular maintenance or care except for the occasional cleaning see chapter 8 5 8 1 New user If the device goes to a new user we recommend a safety check 8 2 Charger Please exclusively use the AAT Alber Antriebstechnik GmbH charger to char ge your battery packs 8 2 1 Automatic charger The charger does not need any particular maintenance The scope of delivery includes the AAT Alber Antriebstechnik GmbH charger Plug O is inserted into the wall outlet and plug O into the socket on the device or the battery pack This automatic charger recharges your batteries 100 As soon as the char ging process is completed it switches to a retaining mode thus overcharging is impossible
11. 5 3 Power unit HH 24 6 Control and display elements 2 2 2 2 2 nn 258885 25 6 1 EMU ev ee 38 25 6 2 Charge of battery lr 26 6 3 Control light to indicate malfunction 27 6 4 Trouble SNOGLNE o 8 2 Bud w a of 65 lius M 28 7 Accessories au cw wo a ko ko ROR eR a 29 del Battery pack 2 2 22 22222 rrr 29 V2 Voltage converter for your vehicle 29 8 Care maintenance and recycling 30 8 1 New user 222 aa e 30 8 2 Sr EE 30 8 3 Battery PAK EE 32 8 4 PUSO MIC 34 8 5 a A AAA 34 8 6 Recycling cad Gad dau Gee de wk 34 rs 34 9 Warranty and liability 39 94 Warranty s s x dox sw xoxo EE E eo a 55 9 2 a assi EmA dA aa erh Bda 39 AAT Ideen bewegen mehr movilino 1 General information Congratulations The movilino is a pushing and braking aid operated by an assistant Special brackets make it possible to mount the movilino easily to almost any type of wheelchair movilino supports the assistant in pushing and braking a wheelchair It faci litates driving on slopes and brakes automatically when going downhill providing safety With the movilino one person could be carried safely and without any effort up to a increase of 18 The movilino is suitable for the transportation on le vel base he is compact light and versatile The sticker with the device s serial number is located on the side
12. ability 2222 on nn 5 2 Description of the product 2 2 2 2 2 nn m nn 288 6 2 1 Adequate use m nn 6 2 2 Features of the movilino 1 2 5 Technical data i s e s ie ox ze die di ie a Wu 9 2 4 Dimensioned sketch LL 10 2 Standard scope of delivery 11 2 6 Optional accessories LL 2 22 m nn 11 3 Assembly 2 2 2 2 2 a nn 12 3 1 Handle ss a ee r 12 dud Brackets l l rre 14 3 9 Attach the battery pack 16 3 4 Detach the battery pack LL 2 2 2 2 nn nn 17 3 5 Adjust the handle 17 3 6 Anti tilt support 2 2 2 En lll ll rn 18 3 7 Functional check 2 HH nn 19 4 Safety instructions 20 4 1 Special information concerning the operation 20 4 2 INSTRUCTION s ie 45 ma eo x 64 X Xx X X 21 4 3 Operation attendant 21 4 4 Wear limit 5 amp 2 5 amp 2 a 4 a Ze E 22 4 5 Hoek O EEE 22 4 6 Care and maintenance 22 4 7 Condition of paths walkways etc 22 4 8 Charge of the batteries L 22 var nn 22 4 9 Power unit oaoa a a a a a a 23 4 10 Transport Bet Bet 82 28 nsd omo dcs 23 4 11 Mounting the brackets 222 a a a 23 4 12 Technical requirements 23 5 Operation 2 2 2 2 aa nn 24 5 1 Maximum lifting capacity 24 D Battery pack 24
13. at the ones of the movilino Also always check the height of your anti tilt support and keep in mind the wheelchair manufacturer s stipulated maximum height The current road traffic regulations apply when you use the movilino on pub lic roads Should there be additional devices necessary you need to mount them to your wheelchair as soon as possible In such case please contact your local dealer Please avoid driving parallel on steep slopes to avoid a tilting over sideways of your wheelchair Always counter steer when the curb on the sidewalk is slanting downward and remain at a safe distance to the curb 20 movilino AAT Ideen bewegen mehr movilino Please do not drive to the edge of stairs or precipices with the movilino tur ned on 5 Please do not attach anything to the movilino s handle Please check the anti tilt support before each use Please do not drive bac kwards against a wall with mounted anti tilt support because they could jam and thus not function properly EF Attention if the powered wheels do not automatically go upward anymore it is difficult to remove the movilino You need a lot more physical power see chapter 3 2 3 3 3 In such case please first apply the locking brakes When you use mass transportation such as bus subway tram etc please turn off the movilino and use the locking brakes on your wheelchair Please pay extra attention when crossing streets intersections or railway c
14. be operated by people instructed in the use of the device and further by people who are physically and mentally capable to manage the movilino in all situa tions that may occur while using it 4 3 Operation attendant Thorough instruction into the use of the mo vilino by your dealer or a representative of AAT Alber Antriebstechnik is part of the delivery package and takes place at an appointment of your choice This is a free service at no extra charge 5 Do not use the movilino without being trained to operate it 21 AAT Ideen bewegen mehr For safety reasons please never leave the movilino unattended Should this be unavoidable please take out the safety chip for the engine immobiliser so nobody unauthorized may use the device Only an attendant and not the wheelchair driver him or herself may use the pushing and braking aid movilino because of the danger of tilting the wheelchair especially when driving on slopes The attendant must be able to catch the wheelchair plus the person sitting in it ifthe chair should tilt bac kwards Anti tilt supports are obligatory Should you feel insecure handling the movilino please contact AAT Alber Antriebstechnik GmbH or your authorized dealer 4 4 Wear limit At the inside of the powered wheels the wear limit is marked with arrows Should the profile have reached the tip of the arrow both wheels must be exchanged In such case please contact your local dealer immediately EF
15. bly With a few movements you can assemble the movilino by means of several fixtures and tightening knobs Disassembly is just as easy 3 1 Handle First connect the handle with the power unit by inserting the column O into the holding device on the power unit A 9 pin Sub D socket connector O located in the power unit s holding device makes the electrical connection 12 movilino Ideen bewegen mehr movilino Secure the connection with the tightening knob 0 EF Please always make sure that the handle is safely connected to the power unit 5 Please only connect the handle with the power unit if both parts are clean and dry Should there be dirt or moisture the two parts should never be connected 5 Clean and dry the Sub D socket connector with a regular cleaning cloth 5 You may not connect other devices to this Sub D socket connector This could destroy the movilino or the other electric devices 13 Ideen bewegen mehr 3 2 Brackets The movilino may only be used if your wheelchair has been supplied with special brackets These brackets may only be mounted by AAT Alber Antriebstechnik or autho rized personnel 3 2 1 Bracket on the wheelchair The wheelchair must be equipped with a bracket in order to attach the movi lino to the wheelchair AAT Alber Antriebstechnik GmbH offers a universally applicable mounting system We attach a holding device O on both sides of the wheelchair
16. ed by AAT Alber An triebstechnik GmbH or its authorized personnel operation of the movilino with insufficiently charged batteries the upper and lower brackets as well as the adjusting rings of the mo vilino were not properly adjusted to the respective wheelchair 55 AAT Ideen bewegen mehr movilino AAT Alber Antriebstechnik GmbH Postfach 10 05 60 D 72426 Albstadt Tel 49 74 31 12 95 0 Fax 49 74 31 12 95 35 www aat online de infoQaat online de
17. emoved 3 Now push the movilino from behind the wheelchair under the chair until the lower rod O is inserted all the way into the lower bracket of the wheelchair 3 2 4 Insert the movilino into the upper bracket on the wheelchair There are two possibilities to insert the movilino into the upper brackets on the wheelchair Possibility 1 1 Tiltthe movilino forward to lift the upper bracket 2 The movilino aligned in the center of its upper support O slides into the upper brackets O the adjusting rings rest snugly against the in side of the brackets on both sides Possibility 2 3 Plugthe power cable into the movilino s battery pack as described in chapter 3 3 4 Insert the safety chip for the engine immobiliser into its appropriate slot 5 Now turn on the device At this point the running wheels are automa tically moving downward and the upper support is lifted up 6 Is the movilino aligned in the center of its upper support slides into the upper brackets O the adjusting rings rest snugly at the insi de of the brackets on both sides EF Please make sure that the lower support is properly hooked into the lower brackets on the wheelchair This goes for both possibilities EF The adjusting rings must always be at the inside of the brackets I9 AAT Ideen bewegen mehr 3 2 5 Fix the movilino to the wheelchair 1 Take one of the quick pins and with your thump push down the quick pin in the middle
18. for its electro magnetic compatibility you should still check its electronic functions before each use This Is particularly important if there IS an aerial mast nearby 4 8 Charge of the batteries You should only use the movilino with fully charged batteries The light emitting diode indicates the state of the batte ries capacity 22 movilino AAT Ideen bewegen mehr movilino EF Please be careful when going downhill with full batteries The drive down generates electricity which charges the batteries additionally This may lead to excess voltage which in turn may lead to a turning off of the movilino During regular use the device reduces its speed automatically to avoid overvoltage 5 f the batteries are empty the device goes into undervoltage It stops Yet the hub motor still drives upward so you may push the wheelchair manually 4 9 Power unit The movilino plus its power unit is for the most part co vered by the housing Nevertheless please make sure that while driving you do not put fingers or hands into the rotating area e g chain wheel or driving pinion Always keep a safe distance 4 10 Transport You may remove the movilino s handle unit see chapter 3 1 for transportation Please lift the power unit exclusively by its recessed handle see chapter 2 2 2 5 Always turn off the movilino for transportation 5 When you transport the device in vehicles please secure it accor ding to the releva
19. g diode O diode located on the control panel next to the ON Off switch informs you about the charge of the battery 5 Green light the charge of the battery lies between 70 100 EF Yellow light the charge of the battery lies between 40 70 96 5 Red light the charge of the battery lies under 40 96 You must char ge the battery immediately 26 AAT Ideen bewegen mehr movilino AAT Ideen bewegen mehr movilino 6 3 Control light to indicate malfunction Malfunction is indicated by a blinking light emitting diode If there is still an indication of malfunction charge the batteries in case of low battery charge For all other cases of malfunction please contact your authorized dealer LED is blinking Type of malfunction Low voltage batteries empty Malfunction of the motor the motor controller or the battery pack Overvoltage Electro magnetic brake at fault Indicator for excess voltage Indicator for overstressing In cases of malfunction such as the blinking of 1 4 times we consciously abstained from automatically activating the electro magnetic brakes as soon as the malfunction Is recognized while the device is driving EF f you want to activate the electro magnetic brake push the rocker switch hard to overcome the pressure point and the panic switch is activated Then release the rocker switch In all other cases of malfunction the electro magnetic brake is automatica
20. lly activated 6 4 Trouble shooting If there are problems using the movilino please check the following trouble shooting chart and see whether you cannot fix them yourself Problem Check and potential solution Is the charger connected to the movilino If so disconnect the charging cable and plug in the power cable Is the battery empty If so charge the batteries movilino cannot be turned on Are the fuses damaged If so exchange the fuses your dealer If there is still a problem turning on the movilino please contact Batteries don t charge Please contact your dealer ay 6 5 Transport For transportation you may remove the handle see assembly chapter 3 1 and carry the climbing unit at the upper rod Note that the device weighs 10 5 kg 5 Always turn off the movilino for transportation 5 When transporting the movilino in a vehicle always secure the devi ce according to the legal rules and regulations The sealed lead acid batteries used in the movilino are not conside red dangerous according to the IATA special guidelines A67 and GGVS Rn Nr 2801 A section 2 and admitted to air travel by DOT and IATA EF Before using mass transportation such as buses or subways etc or your personal vehicle please detach the movilino from you wheel chair 28 AAT Ideen bewegen mehr movilino 7 Accessories 7 1 Battery pack The movilino works with batteries and is deli
21. movilino ing ai Pushing and brak GB user s manual igina Translation of the or i D E D OD D QD O Es D D IS AAT Ideen bewegen mehr CE Declaration of conformity The company AAT Alber Antriebstechnik GmbH herewith declares that the products of the pushing and braking aid movilino were developed and manu factured in concordance with the regulations of the European Union EEC Guidelines 2007 47 EG and 2006 42 EG This declaration becomes void if the above mentioned devices have been al tered without the consent of Alber Antriebstechnik GmbH C Signature of the manufacturer Markus Alber Managing shareholder AAT Alber Antriebstechnik GmbH The pushing and braking aid movilino is being tested according to the norm DIN EN 12184 and 12182 at the institution for cer tification of medical products GmbH Tech nical University Berlin M TESTED AND MONITORED AAT Alber Antriebstechnik GmbH Postfach 10 05 60 D 72426 Albstadt Tel 07431 12950 Fax 12 95 35 info aat online de www aat online de movilino gb 09 2010 movilino AAT Ideen bewegen mehr movilino Table of contents CE declaration of conformity 2 Table of contents un 3 1 General information 2 2 2200 nn 5 1 1 How to use this users manual 5 1 2 Instruction Lok se a a ox Um e Ue X 9 Ue 5 143 Care and maintenance 5 1 4 Warranty and li
22. nt legal regulations in your country 4 11 Mounting the brackets Attaching the movilino s brackets to the wheelchair or making changes on said brackets may only be performed by the company AAT Alber Antriebstechnik or their authorized dealers The movilino may only be attached to wheelchairs which must be checked according to generally acknowledged technical norms and their operator s manuals must be applied when using the movilino Before each use please check all the holding devices and attachments Also make sure that the device itself functions properly Should anything not work you may not use the movilino In that event please contact your local dealer 4 12 Technical requirements 5 You may not remove the wheelchair s wheels Please always check the air pressure of pneumatic steering rollers The movi lino driving qualities could be affected negatively if there is not enough air in the rollers The air pressure in the wheelchair s wheels must correspond to the wheel chair manufacturer s stipulations The running wheels condition also must be checked before each use Should the wheels have reached their wear limit see chapter 4 4 you may not use the movilino After you have inserted the safety chip for the engine immobiliser into its proper slot on the handle the movilino is ready to go Therefore please al ways check whether the chip is properly inserted before you use the device The wheelchair s locking brakes m
23. on of the product 2 1 Adequate use Please use the braking and pushing aid movilino exclusively for the transpor tation of physically disabled persons Said person should be able to sit properly without help otherwise you should secure them with a safety belt The latter is an accessory available at AAT Al ber Antriebstechnik GmbH In addition the arms of the person to be transported should not protrude over the arm rests of the wheelchair during the transportation process 5 nthe interest of your safety you may not use the movilino on escala tors or moving belts 5 Transporting other kinds of loads is explicitly prohibited EF Only authorized operators may use the movilino Therefore never lea ve the movilino unattended EF Due to safety reasons the movilino may only be operated by trained personnel who are physically and intellectually capable to handle the device in all situations of operation EF Please note the wheelchair manufacturer s specifications wheels air pressure maximum approved total weight maximum incline etc when using the movilino You may under no circumstances ex ceed the specified limiting values EF You should avoid operating the device on unfortified grounds sand mud loose gravel ice or snow as well as crossing deep puddles maximum depth approximately 2 5 cm with it AAT Ideen bewegen mehr movilino 2 2 Features of the movilino O handle O column O brackets
24. ot insert the chip you can turn on the device but it does not work This is a safety feature to ensure that no unauthorized person uses the movi lino 25 6 1 4 Rocker switch With the rocker switch you determine the direction and speed up to the pre selected speed of the movilino 5 Use the rocker switch carefully To drive forward you press the longer back part of the rocker switch O To drive backward please press the rocker switch s shorter front part 6 The movilino speeds up the more you press the rocker switch until you reach the maximum pressure point It slows down the more you release the rocker switch Two seconds after standstill is reached an electro magnetic parking brake becomes active 6 1 5 Panic switch If during an emergency you press the rocker switch too hard so that the pres sure point is overcome the so called panic switch causes the movilino to go from driving mode into coast s long as you keep the rocker switch pressed you can drive the patient away from the dangerous situation However as soon as you release the rocker switch the electromagnetic brake is activated Depending on particular circumstances the electro magnetic brakes strong effect may brake the wheelchair so abruptly that it stops immediately The panic switch works both ways going backward and forward as well as du ring malfunction please see chapter 6 4 for trouble shooting 6 2 Charge of battery A light emittin
25. our safety the pushing and braking aid movilino may not be used on escalators stalrs moving walkways or unfortified surfaces You may only move the wheelchair plus mounted movilino manually if the device is turned off Please observe the instructions and limiting values of your wheelchair s manufacturer Before each operation you must put the safety chip for the engine immobili ser into its slot at the handle unit Always make sure it has snapped into pla ce because otherwise the movilino does not work 5 The wheelchair s wheels may not be removed Please make yourself familiar with handling the device and its driving cha racteristics Please use it first on level ground until you feel secure handling it Also practise at a low speed EF n the beginning please always turn the speed control to its lowest speed and increase it until you reach the desired pace 5 Please reduce the speed before going downhill 5 On slopes and inclines the movilino must always be activated Although the movilino manages inclines up to 18 you may under no cir cumstances exceed the maximum approved inclination stipulated by your wheelchair manufacturer Ramps in public places generally have an inclina tion of approximately 6 EF Please cross over obstacles such as curbs on sidewalks with a turned off movilino Crossing over higher curbs should be done backwards because the rollers may jackknife Please pull the wheelchair at its handle not
26. rability EF Ifthe battery pack is totally discharged it takes a maximum of ap proximately 10 hours to recharge it The battery pack can be charged in any position It is considered as safe as dry cells and admitted to air travel by DOT and IATA 5 Always charge your battery pack with the AAT charger delivered with your movilino This particular charger automatically turns off when the batteries are fully charged keeping them from being overchar ged 32 movilino AAT Ideen bewegen mehr movilino 8 3 1 Charging with the automatic charger To charge the batteries you may leave the battery pack in Its bag attached to the wheelchair First pull the plug of the power cable then insert the plug of the charger entirely into the charging socket Finally plug the charger into the wall outlet 5 Since the movilino is supposed to be connected to the charger at all times whenever it is not in use you need to remove the charger from the wall outlet and pull the plug from the charging socket on the bat tery pack every time before you use it EF Before charging please read and follow all instructions and warning notes printed on the charger EF Exclusively use the AAT Alber Antriebstechnik GmbH charger 5 Never touch the plug with moist hands Signals of the charger charger LED orange batteries are being charged charger LED green batteries are fully charged maintenance mode 8 3 2 Charging
27. ranty and liability Warranty AAT Alber Antriebstechnik GmbH grants a warranty of two years for all its products of type movilino including all its accessory parts with the excepti on of the sealed lead acid batteries The warranty begins at the date of pur chase and covers failure of material and errors in manufacturing For the sealed lead acid batteries always assuming correct maintenance AAT Alber Antriebstechnik GmbH grants a warranty of 6 months from the date of purchase The warranty becomes void concerning defects or damage which are the re sult of the following 9 2 damage due to excessive strain damage due to improper handling violent damage natural wear and tear such as powered wheel improper and insufficient maintenance unauthorized constructional changes or inappropriate use of the de vice or Its accessories using the movilino exceeding its maximum lifting capacity improper charging of the lead batteries Liability The manufacturer AAT Alber Antriebstechnik GmbH is neither liable nor re sponsible for potential damage of the movilino In case of improper handling of the device repair assembly or other work performed on the movilino by unaut horized persons operation not in accordance with this user s manual extraneous parts added or connected to the movilino parts removed from the movilino operation exceeding the maximum lifting capacity no regular biannual maintenance check perform
28. rized dealer 8 5 Cleaning Please clean your control unit driving unit battery pack and brackets with a mild household cleaner 5 Please keep in mind to clean the powered wheel with compressed air or with a dry brush regularly It is possible that the powered wheel is excessive worn up because of contamination or deposits E Make sure that no water gets into the movilino therefore merely use a damp cloth for cleaning 5 nthe interest of your safety do not use a high pressure cleaning de vice EF Please make sure that your wheelchair is cleaned according to the manufacturer s specifications 8 6 Recycling The movilino and its battery pack are products of long durability However if your movilino is old and has reached the end of its lifespan you may return its components to AAT Alber Antriebstechnik GmbH or your local dealer to be recycled A new law concerning electric and electronic devices ElektroG has been passed on March 24 2005 regulating the taking back and recycling of old electric and electronic devices According to the Federal Office of Environment Protection German BDU the movilino is considered a means of transportation and does not fall under the law concerning the recycling of old electric or electronic devices Elek troG 2 paragraph 1 sentence 1 cross reference Guideline of the European Parliament 2002 96 EG 34 movilino AAT Ideen bewegen mehr movilino 9 9 1 War
29. rossings Please never cross rails e g railway tracks in a parallel way because the wheels could be jammed 4 1 1 Environmental conditions electro magnetic compatibility Elec tro magnetic compatibility means that an electric device functions properly in its electro magnetic environment without influencing other devices in the same environment The movilino successfully passed all the EMV tests required by law Never theless always check whether the device s electronic functions work proper ly before each use This is particularly important if there is an aerial mast nearby EF Please note that the movilino may interfere with other electronic devices sensitive electro magnetic fields e g anti theft systems in department stores This may also happen if you connect other devi ces EF Also make sure that the movilino is not operated in close proximity to medical devices with a high potential for danger and or life suppor ting functions as well as diagnostic devices 4 1 2 Climate To ensure proper functioning it is not advisable to expose the movilino to freezing conditions Should this be unavoidable always put the device in a non freezing environment for at least one hour before using it see chapter 2 3 EF At this point check the device before operation Should your movili no not function properly please call your local dealer or AAT direct ly 4 2 Instruction n the interest of your safety the movilino may only
30. s fra me This holding device has an upper O and lower O bracket All brackets are specially designed for and adjusted to each individual wheelchair therefore the brackets you see in the picture may look different from your wheelchair brackets 5 Please check whether the brackets are securely fastened before each use Should screw fastenings be loose you may not use the movili no In such case please contact your local dealer immediately 3 2 2 Bracket on the movilino On your movilino you find an upper O and lower O rod To adjust the lower rod s height there are several vertical holes drilled into the housing of the movilino Your authorized dealer or AAT Alber Antriebstechnik GmbH adjusts the height at which the movilino is mounted to your type of wheelchair On both sides of the upper rod there are rings O The position of said rings are also adjusted to your type of wheelchair 14 movilino AAT Ideen bewegen mehr movilino 3 2 3 Insert the movilino into the lower bracket on the wheelchair 1 Please use the locking brakes of your wheelchair to avoid any move ment of the chair while the movilino Is being mounted 2 Tilt the movilino slightly backwards As soon as the device sits on its wheels you may push the movilino back and forth This only works if you keep the device tilted backwards 5 These helping wheels are only active when the device is tilted 5 Make sure that the anti tilt support is r
31. secured in the hol ding devices If you can remove the quick pins without pressing the unlocking button they are not secured properly 5 Please make sure that the tilt support is not jammed whenever you use the movilino 5 Please do not drive backwards against a wall with mounted tilt supp orts EF Please note that no tilt support can secure all potentially difficult si tuations thus avoid any instable situations even with mounted tilt supports To remove the tilt support you press the unlocking button on the quick pin while you pull it out Then take off the tilt support 18 movilino AAT Ideen bewegen mehr movilino Brackets movilino s max Slide the tilt support all the way into the holding device O on the movili no Pay attention on the label at the anti tilt support Lock it with the quick pin Push the quick pin into the drilling on the holding device while you press the unlocking button at the top of the quick pin When the quick pin is inserted all the way you release the unlocking button on the quick pin CE Please check whether the quick pins are tightly secured in the hol ding devices If you can remove the quick pins without pressing the unlocking button they are not secured properly Please make sure that the tilt support is not jammed whenever you use the movilino Please do not drive backwards against a wall with mounted tilt supp orts Please note that no tilt support can sec
32. ure all potentially difficult si tuations thus avoid any instable situations even with mounted tilt supports To remove the tilt support you press the unlocking button on the quick pin while you pull it out Then take off the tilt support 3 7 CET Functional check Please check the device s electronic functions each time before using it see chapter 6 1 Please regularly check the wear limit of the powered wheels see chapter 4 4 Make sure that the battery pack is charged before you use the movilino Please make sure that the tilt support is not jammed whenever you use the movilino 19 AAT Ideen bewegen mehr 4 Safety instructions EF For a safe operation of the movilino it is important that you observe and adhere to all warning signs and instructions in this user s manu al as well as the warning signs and instructions on the device itself All general rules for the safe use of a wheelchair apply without reservation while operating the movilino You must always observe the limit values and instructions indicated by the manufacturer e g air pressure maximum total weight maximum inclination etc Limit values may never be exceeded To assure a safe use of the movilino it is indispensable to observe the follo wing directions 4 1 Special information concerning the operation Generally all of the wheelchair s specific limiting values indicated by the manufacturer must be observed In the interest of y
33. ust be attached in such a way that the at tendant may reach them easily It is indispensible to use anti tilt support Please make sure that they are not jammed before each use Also never drive backwards against a wall with mounted anti tilt support 23 AAT Ideen bewegen mehr 5 Operation 5 1 Maximum lifting capacity Please make sure that the maximum lifting capacity of 170 kg wheelchair person and movilino is not exceeded 5 2 Battery pack Please make sure that the batteries are fully charged before you use the mo vilino for the first time Extensive instructions you find in chapter 8 3 5 5 Power unit Please regularly check the wear limit of the powered wheels Extensive instructions you find in chapter 4 4 24 movilino AAT Ideen bewegen mehr movilino 6 Control and display elements Before we get to the actual instructions for operation we would like to intro duce the movilino s most important components to you Your movilino is ready to go when you receive it Once the movilino is correct ly mounted and connected you can turn it on and use it immediately Please practise using It with an empty wheelchair to get a feeling for the ma chine and its functions 6 1 Control unit The wheelchair driver s attendant controls all of the movilino s functions by means of the control unit 5 It is possible to supply you with a left handed control for additional charge 6 1 1 ON OFF switch
34. vered with one battery pack with charging electronics If you use the movilino often i e if there are not sufficient breaks for the bat teries to be recharged we recommend you obtain an additional battery pack available as an accessory In such case one battery pack is in use while the other is being recharged at the same time EF f you do not use the movilino both battery packs should be connec ted to the charger to increase their durability see chapter 8 3 1 EF Please exclusively use the AAT Alber Antriebstechnik GmbH charger to charge your battery pack 7 1 1 Exchange the battery pack 1 Turn off the movilino using the ON OFF switch 2 First remove the power cable from its socket on the movilino After wards remove the plug of the power cable from the socket on the bat tery pack 3 Please open the velcro strip of the bag for the battery pack and take out the battery pack 5 The battery pack should always be connected to the charger to ex tend its durability see chapter 8 3 1 EF Please exclusively use the AAT Alber Antriebstechnik GmbH charger to charge your battery pack The battery pack of the movilino is maintenance free and rechargeable Its durability depends directly on the number of charging discharging cycles 7 2 Voltage converter for your vehicle We recommend the voltage converter for your vehicle if you transport the stairclimber movilino in your car The AAT voltage converter is designed for a
35. ypically below 60 dB noise level the weighted RMS value of acceleration the upper body vibration specifications is exposed to lies typically below 2 5 m s2 Limiting values stipulated by the wheelchair manufacturers must be noted and observed Braking and climbing capacity depend among other things on the weight of the person to be transported as well as the ground profile terrain tempe rature etc According to ISO 7176 4 the range depends among other things on the person s weight the ground territory temperature etc In the interest of progress we reserve the right for technical changes AAT Ideen bewegen mehr movilino 2 4 Dimensioned sketch min 0 max 18 926 Un Sie Uy 10 AAT Ideen bewegen mehr movilino 2 5 Standard scope of delivery The following is part of the standard scope of delivery O movilino power unit plus handle O battery pack O charger as well as the components mounted to the wheelchair power cable and bag for the battery pack plus the user s manual no picture In addition it is necessary to mount brackets to the wheelchair this Is not included in the delivery package 2 6 Optional accessories We offer the following accessories for your personal needs and wishes Spokes protection mega battery pack anti tilt support voltage converter hip belt and handle for left handed control 11 Ideen bewegen mehr 3 Assem
Download Pdf Manuals
Related Search