14` x 32` x 12` Round Top® Assembly Instructions
Contents
1. cable provided through the eyelet of the anchor and around the frame as shown below Secure the cable with the clamps provided NOTE 15 Augers are for temporary use only For best results ShelterLogic recom mends using our Easy Hooks 10036 4 pack 10035 6 pack or 10038 8 pack or 30 Augers 10075 4 pack 10078 6 pack or 10079 8 pack for a stronger more secure installation End Rib Anchors Call 1 800 524 9970 or visit www shelterlogic com for more information Page 6 05 62669_0G 7 DOOR AND SOLID END PANEL INSTALLATION A Hold end panel at the top center with white inner surface facing inside of the shelter Wrap the edges of the fabric panel around the end rib and pass the rails through the pre made slits in the fabric B Disconnect top rail the horizontal pipes that run from front to back along the top from the end rib Pull the webbing the black strap below the cross rail Reattach the top cross rail to the end rib Repeat Step B for side rails the horizontal pipes that run from front to back along the sides of the unit near the bend in the frame where the legs meet the roof C At the bottom where the webbing exits the pocket on each side of end panel pull webbing to remove the slack Be careful not to pull the webbing through the other side of the webbing pocket D Insert the S Hook on ratchet into hole on the leg bend Insert the webbing into the spindle of the ratchet and pull ti2. 0110 COVER RAILS e Webbing and Ratchets Securing Cover End Rib Cross Rail Clamps Middle Rib Cross Rail Clamps 10115 Page 8 05 62669_0G
3. 14 x 32 x 12 Round Top Round Style Shelter Assembly Instructions DESCRIPTION 14 x 32 x 12 RoundTop Garage Gray MODEL 62669 RECOMMENDED TOOLS Please read instructions COMPLETELY before assembly This shelter MUST be securely anchored THIS IS A TEMPORARY STRUCTURE AND NOT RECOMMENDED AS A PERMANENT STRUCTURE Before you start 3 individual recommended for assembly approximate time 3 hr VIEW AN ONLINE INSTRUCTIONAL VIDEO OF A GARAGE BEING BUILT www ShelterLogic com 1 800 524 9970 er Tit el 1 800 559 6175 1 3 11 Page 1 05_62669_0G ATTENTION This shelter product is manufactured with quality materials It is designed to fit the ShelterLogic LLC custom fabric cover included ShelterLogic LLC Shelters offer storage and protection from damage caused by sun light rain tree sap animal bird excrement and light snow Please anchor this ShelterLogic LLC structure properly See manual for more anchoring details Proper anchoring keeping cover tight and free of snow and debris is the responsibility of the consumer Please read and understand the installation detail warnings and cautions prior to beginning installation If you have any questions call the customer service number listed below Please refer to the warranty card inside this package DANGER Prior to installation consult with all local municipal codes regarding installation of temporary shelters Choose the locat
4. forecast in your area we recommend removal of cover REPLACEMENT PARTS ASSEMBLY SPECIAL ORDERS Genuine ShelterLogic LLC replacement parts and accessories are available from the factory including anchoring kits for nearly any application replacement covers wall and enclosure kits vent and light kits frame parts zippered doors and other accessories All items are shipped factory direct to your door QUESTIONS CLAIMS SPECIAL ORDERS CALL OUR CUSTOMER SERVICE HOTLINE U S CUSTOMER SERVICE 1 800 524 9970 INTERNATIONAL CUSTOMER SERVICE 001 860 945 6442 CANADA CUSTOMER SERVICE 1 800 559 6175 HOURS OF OPERATION MON FRI 8 30AM 8 00PM EST SAT SUN 8 30AM 5 00PM EST CARE AND CLEANING A tight cover ensures longer life and performance Always maintain a tight cover Loose fabric can accelerate deterioration of cover fabric Immediately remove any accumulated snow or ice from the roof structure with a broom mop or other soft sided instrument Use extreme caution when removing snow from cover always remove from outside the structure DO NOT use hard edged tools or instruments like rakes or shovels to remove snow This could result in punctures to the cover DO NOT use bleach or harsh abrasive products to clean the fabric cover Cover is easily cleaned with mild soap and water WARRANTY This shelter carries a full limited warranty against defects in workmanship ShelterLogic LLC warrants to the Original Purchaser that if pr
5. ght Wind the ratchet so that the webbing overlaps itself Position the end panel so that it is centered on the building before fully tightening the end panel E Tighten ratchets alternating from one side to the other until the end panel is tight Olegi stm Keep Zippers closed when tightening end panels WRAP END PANEL EDGES OVER AND AROUND PIPE TOWARDS INSIDE OF FRAME DO NOT INSERT ANY PIPES EL NTO THESE POCKETS L TOP CROSS RAIL WRAP END PANEL EDGES TO INSIDE OF FRAME SIDE CROSS RAILS ZIPPERS WEBBING INSIDE VIEW OF END RIB Page 7 05_62669_0G 8 INSTALLING COVER AND COVER RAILS A Lay the cover on the ground next to the frame with inside of the cover the side with the pipe pockets facing down and the webbing on the front and rear of the corner of the building Pull cover over the frame B Insert the S Hook on ratchet into hole on the leg bend Insert the webbing into the spindle of the ratchet and pull tight Wind the ratchet so that the webbing overlaps itself C Disassemble cover rails and slide through fabric pockets at each leg and reattach with clamps to each leg Repeat this on other side Push down on cover rails to tighten cover before tightening bolts completely D Check and tighten Ratchets and Cross Rails monthly to ensure the cover is tight NOTE The RT Brand logo should be oriented as shown below CORRECT AYR Kt A hth ICI 1
6. ion of your shelter carefully DANGER Keep away from electrical wires Check for overhead utility lines tree branches or other structures Check for underground pipes or wires before you dig DO NOT install near roof lines or other structures that could shed snow ice or excessive run off onto your shelter DO NOT hang objects from the roof or support cables WARNING Risk of fire DO NOT smoke or use open flame devices including grills fire pits deep fryers smokers or j lanterns in or around the shelter DO NOT store flammable liquids gasoline kerosene propane etc in or around your shelter Do not expose top or sides of the shelter to open fire or other flame source IK CAUTION Use CAUTION when erecting the frame Use safety goggles during installation Secure and bolt together overhead poles during assembly Beware of pole ends PROPER ANCHORING AND INSTALLATION OF FRAME PROPER ANCHORING OF THE FRAME IS THE RESPONSIBILITY OF THE CONSUMER ShelterLogic LLC is not responsible for damage to the unit or the contents from acts of nature Any shelter that is not anchored securely has the potential to fly away causing damage and is not covered under the warranty Periodically check the anchors to ensure stability of shelter ShelterLogic LLC cannot be responsible for any shelter that blows away NOTE Your shelter s cover can be quickly removed and stored prior to severe weather conditions If strong winds or severe weather is
7. ock Assembly 800260 10210 Lo H01010 ShelterLocks and Cross Rail Poles attach to inside of frame CROSS RAILS WIND BRACES COVER CROSS RAILS Use 02030 to connect Front end rib Use 02031 to connect Rear end rib End Rib Cross Rail Clamps e Aa 1o11 Middle Rib Cross Rail Clamps Ve j 10111 A 10110 10115 10110 4 ATTACH TOP CROSS RAILS Top Cross Rail UNDER End Ribs Install the top cross rail over the middle ribs 02030 Tae and underneath end ribs 02030 _ lt 02030 A i A 10224 __ 10225 Ig X gt 4 r EA J at Front End Ri 02031 lt a gt at Back End Rib 01010 yy A Top Cross Rail OVER Middle Ribs va i 02030 NG 10225 10224 aa i N 01010 a EY Page 5 05_62669_0G 5 SQUARING UP THE FRAME A Place frame in its final location which needs to be as flat and level as possible B Measure across opposite corners These distances must be equal to within 1 inch C Check that the front and rear of the frame measures 14 feet in width 6 PROPERLY ANCHOR FRAME A Anchors must be placed inside shelter at the corners of the shelter Insert a 4 inch pipe or steel rod through the eyelet of the auger and screw the anchor into the ground until the eyelet is sticking out of the ground by 1 to 2 inches so it can be anchored to the legs If ground is too hard dig a hole with a shovel or post hole tool Optional Fill with cement B Wrap
8. operly used and installed the product and all associated parts are free from manufacturer s defects for a period of 1 YEAR FOR COVER FABRIC END PANELS AND FRAMEWORK Warranty period is determined by date of shipment from ShelterLogic LLC for factory direct purchases or date of purchase from an authorized reseller please save a copy of your purchase receipt If this product or any associated parts are found to be defective or missing at the time of receipt ShelterLogic LLC will repair or replace at it s option the defective parts at no charge to the original purchaser Replacement parts or repaired parts shall be covered for the remainder of the Original Limited Warranty Period All shipping costs will be the responsibility of the customer Parts and replacements will be sent C O D You must save the original packaging materials for shipment back If you purchased from a local dealer all claims must have a copy of original receipt After purchase please fill out and return warranty card for product registration Please see warranty card for more details Covered by U S Patents and patents pending 6 871 614 6 994 099 7 296 584 D 430 306 D 415 571 D 414 564 D 409 310 D 415 572 080310 Page 2 05 62669_0G 14 x 32 x 12 RoundTop Garage Parts List Model 62669 Description of Parts Quantity Part 10563 802617 802616 800260 10040 Cover Cross Rail 45 3 4 Cross Rail 48 1 2 Cr
9. oss Rail Swedge 50 1 2 Middle Upright Tube 55 1 2 gt Wind Brace Flat Ends 67 3 8 Bent Corner Leg Side Bend Plain 80 Side Bend Swedged 80 Extension 54 T Cover Triple Zipper Door ill Back Panel ShelterLock Stabilizer Block lel Ratchet Clamp Half Clamps for Middle Legs i Half Clamps for Corner Legs CY Bolts 1 4 x 3 For Cross Rail AN Round Head Bolts 1 4 x 3 Top Bolts 1 4 x 2 For Frame lt Bolts 1 4 x 1 5 8 For Clamps Nut 1 4 Bolt Caps Base Feet h Ce 15 Auger Anchors Temporary ra Cable 1 Length Cable Clamps EA EE lt a ES ES ES EE EA EA EN 37 m a a e za ES EA Ea EA E ES a Page 3 05 62669_0G 1 ASSEMBLE END RIB Secure all bolts with 1 4 Nuts 01010 10224 3 Bolts 10225 10210 10258 ie p 10258 2 Bolts pe ii i ee 10226 10226 2 ASSEMBLE MIDDLE RIBS 10224 3 Bolts 10225 802630 10258 Dua oe 10258 2 Bolts 7 ic i on 10273 10273 05 62669_0G 3 ATTACH CROSS RAILS AND WIND BRACES Repeat until all ribs are assembled and securely connected Middle Rib ShelterL
Download Pdf Manuals
Related Search