DSO Communication & Control Software User Manual
Contents
1. i C Serial Single Fig 3 8 Note When using RS 232 for data transmission the transmission interface feature is not supported You can transmit data by menu function gt remote control Fig 3 8 has no waveform display It only provides function control You can use the function keys on this interface to operate your oscilloscope When operation is complete click CLOSE as shown in Fig 3 8 Page 25 of 28 Communication amp Control Software for DSO User Manual Chapter 4 System Prompts and Trouble shooting 4 1 System prompts Time out prompt Check the communication interface configuration See whether the equipment is properly connected and check software driver update SCAN prompt SCAN will perform single transmission Please carry out single refresh Continue Are you sure you want to exit Virtual Instrument A prompt to ask you if you wish to close the software 4 2 Troubleshooting 1 Ifthe system prompts you to check serial or USB configuration when you enter Equipment ON OFF take the following steps Check whether the oscilloscope power plug is properly connected Check whether oscilloscope ports match the communication and control software setups Check whether the cable connection between module and PC is in order Ensure the USB driver is properly installed After carrying out the above checks restart the software and oscilloscope to continue operation 2 Ifyou are unab2. All sub menus under the FUNCTION menu can be operated only when the data transmission or transmission interface task is complete Mathematics functions When this menu is clicked a mathematics function dialog box will pop up to enable mathematics selection or FFT mathematics as shown in Fig 2 6 Page 14 of 28 Communication amp Control Software for DSO User Manual E Math Operation FFT Window Functions Rectangle SOUFCe CHI Fig 2 6 Mathematics selection You can select the mathematical relation between signal sources A and B There are four mathematical relations X Signal source selection There are A and B signal sources You can set them up as CH1 or CH2 channel signals respectively FFT function selection You can switch between Rectangle Hanning Hamming and Blackman FFT signal source selection You can select CH1 or CH2 Remote control You can operate the digital storage oscilloscope on remote control with the communication and control software In the remote control mode the computer screen will display a virtual instrument control panel which is fundamentally the same as the oscilloscope control panel as shown in Fig 2 7 Page 15 of 28 Communication amp Control Software for DSO User Manual zE Far Control Function MENU esou Acure Sorel RUNCONT n VERTICAL v E k VOLTS
3. After installing the communication and control software you can operate your oscilloscope on remote control through LAN or the Internet As it supports concurrent visit by multiple users there are no geographical and users restraints and you can carry out network and remote testing as well as measuring With the optional UT M01 or UT MO5_ Ethernet module you can operate the oscilloscope through the LAN interface as follows Select LAN in the equipment selection option on the real time control panel Page 22 of 28 Communication amp Control Software for DSO User Manual 2 When LAN is selected the dialog box in Fig 3 5 will pop up ETP Address IP Address of DSO 265 255 255 255 Fig 3 5 Enter the DSO IP address in this box The IP addresses set in the software and the communicated oscilloscope must be the same otherwise communication between the oscilloscope and the software cannot be established Please refer to the oscilloscope user manual for operation instructions Access sub menu page 3 by pressing UTILITY LAN on the oscilloscope control panel for TCP IP protocol setup You should set up the IP address netmask and default gateway in LAN In the same network the IP address of every individual digital storage oscilloscope is unique and must not conflict with the IP address of any other equipment in network IP addresses 3 For other operation instructions refer to steps 2 3 4 5 6 and 7 fo
4. Digital Storage Oscilloscope 1 01 The installer now has enough information to install Digital Stora WOU computer The following settings willbe used Instalhtolder CAPragram FilesiDigital Storage Oscillage ip n Te Shortcut folder Digital Storage Oscilloscope Cancel Fig 1 5 Step six In Fig 1 5 after confirming the message is correct click NEXT N to enter the front page for automatic installation as shown in Fig 1 6 Page 5 of 28 Communication amp Control Software for DSO User Manual Ps Digital Storage Oscilloscope Setup Please wat Installing Files CW INDOVSisystem 32 icvirte dll Cancel Fig 1 6 Step seven When automatic installation is complete and the box shown in Fig 1 7 pops up click the FINISH E button Your oscilloscope communication and control software is now successfully installed on your computer and ready for use Digital Storage Oscilloscope Setup x Installation Successful The Digital Storage Oscilloscope 1 istallation is complete Thank you for choosing Digital Stor Please click Finish to exit this inst g Fig 1 7 To return to the previous installation guide interface click BACK B on any installation guide page To stop installation press CANCEL C on any installation guide page Page 6 of 28 Communication amp Control Software for DSO User Manual 1 3 Running the software When installation of the oscill
5. address setup There must not be two identical GPIB device addresses on one GPIB main line 3 For other operation instructions refer to steps 2 and 3 for USB interface controls in this chapter Note When using the GPIB interface the transmission interface feature is disabled 3 4 Serial interface controls You can control your digital storage oscilloscope with a standard RS 232 port at 4800 baud rate via the serial interface as follows 1 Select RS 232 in the equipment selection option on the real time control panel The dialog box in Fig 3 7 pops up _ Serial Port Setup When transmiting by serial port interface only have single fresht Serial Port Baud Rate comi w 4800 Fig 3 7 2 Click EQUIPMENT ON OFF The indicator lights up when this key is on When it goes off the function is off Page 24 of 28 Communication amp Control Software for DSO User Manual Click DATA TRANSMISSION The indicator lights up when this key is on When it goes off the function is off Note After pressing DATA TRANSMISSION the transmission task may take more than 10 seconds to complete Select FUNCTION remote control in the menu The interface in Fig 3 8 pops up You can now control your oscilloscope with the function keys zE Far Control Function MENU RUNCONT Mesud Acure serege Fuste VERTICAL HORIZONTAL TRIGGER n 7 mn _ VOLTS DIV SEC DIV nm
6. before using the USB communication mode for the first time For instructions please refer to Chapter 1 4 Installing the USB driver When installation is complete run the software and enter the screen shown in Fig 3 1 After selecting USB in the equipment selection option operate as follows 1 Select USB in the equipment selection option on the virtual control panel 2 Click the Equipment ON OFF button to turn it ON The indicator light is green When the button is turned OFF the indicator light will go off as shown in Fig 3 2 ON OFF ON OFF Fig 3 2 ON OFF status display of the equipment selection button 3 Click the Data Transmission button to turn it on When the indicator light comes on the function is ON When the indicator light goes off the function is OFF as shown in Fig 3 3 When data transmission is on you can operate the digital storage oscilloscope with the buttons and knobs on the control panel The parameters and setups of the virtual control panel will change accordingly WaveForm WaverForm Fig 3 3 ON OFF status display of the data transmission button 4 When data transmission is complete Click the Data Transmission button again to turn it off During data transmission you cannot operate the oscilloscope with the software The function keys on the virtual control panel are disabled but they continue to indicate the current status of the oscilloscope Page 21 of 28 Commun
7. DIV SEC DIU HORIZONTAL TRIGGER T T O k Ji T m Is ww no g w om nm L Serial f Single Fig 2 7 The sign of every button or knob on the virtual control panel is identical to that on the oscilloscope control panel You can click the same buttons to operate the corresponding functions To use the virtual control panel efficiently you must be familiar with all function menus as well as the current status of the oscilloscope Note You can only operate the digital storage oscilloscope with the virtual control panel Waveform observation or screen display function is not available You cannot operate the remote control and transmission interface tasks simultaneously Data table This shows the function relation between the voltage and time of the sampling point of the waveform currently on display 1 e V F E Data Table Eg Function 4 z Channel indication Wave Data of CH1 tj oo oof 2 oo ooo a oo ff ooo s ooo ff ooo s oo om e o0 ooo z oo ff ooo a ooo oof a oo ooo w ooo ooo ow ff ooo i 7 Fig 2 8 Page 16 of 28 Communication amp Control Software for DSO User Manual When you click the save data option under function selection on this screen a data table storage interface will pop up as shown in Fig 2 9 Select the data saving path in the save to path selection field enter the document name i
8. Document No SYSC 0 100108 January 2010 Digital Storage Oscilloscope Communication amp Control Software User Manual and Installation Instructions Page 1 of 28 Communication amp Control Software for DSO User Manual Chapter 1 1 1 12 1 3 1 4 Chapter 2 2 1 2 2 2 3 2 4 Chapter 3 3 1 3 2 3 3 3 4 Chapter 4 4 1 4 2 Table of Contents Installation of the Digital Storage Oscilloscope communication and control software sseseseses 3 Hardware TeQUITe IMCS osienkin en a D 3 Installing The Sowa raner a dae Sueates 3 R nno TNS SOW dies can idseiniaiateinnacnsetntete aS 7 Installing the US B driver 2si0cie 20 nen eTEN ices 8 Getting to know your Digital Storage Oscilloscope 11 communication and control software he CONGO Panel srerntncRanp th ace aie ashe eta 11 Mani MENU sorres enrera Maentaogcadere ree ene ea ede 12 Control panel IMS MuCuOns 4s cscs hoch cwcecs T ssteanabuss acs 18 Transmission interface and explanatory notes s eeee 19 Operation guide for the Digital Storage Oscilloscope 20 communication and control software USB interface CONttOlS 4 cscs ctvsekecsccatecatveaesseeieoveband weeswene ease 21 Ethernet LAN interface controls 0 0c cece ec cece cee cece e cues 22 Cr PIB Intercentros aa a a ENS 23 Serial interface Controls 43 nein turn seh aeea aani 24 System Prompts and Trouble shooting 26 SYSED ODIS gashere A a e 26 TOU DIESHOO
9. Found New Hardware Wizard Please wait while the wizard installs the software Digital Storage Oscilloscope oy Setting a system restore point and backing up ald files in case your system needs to be restored in the future Fig 1 13 4 As shown in Fig 1 13 the hardware installation wizard of your digital storage oscilloscope begins automatic searching and installing the USB driver for the oscilloscope communication and control software When installation is complete the dialog box shown in Fig 1 14 pops up Found New Hardware Wizard Completing the Found New Hardware Wizard The wizard has finished installing the software for Digital Storage Oscilloscope Click Finish to clase the wizard Back Cancel Fig 1 14 Page 9 of 28 Communication amp Control Software for DSO User Manual 5 In Fig 1 14 click the FINISH F button Your USB driver is now installed and instant communication and control are enabled between the oscilloscope and the software Please read 3 1 USB Interface Controls in Chapter 3 Operation guide for the oscilloscope communication and control software of this booklet prior to operation Page 10 of 28 Communication amp Control Software for DSO User Manual Chapter 2 Getting to know your oscilloscope communication and control software 2 1 The control panel After the oscilloscope communication and control software is activated a display panel similar to the dig
10. LN Gc cnc eun a E E E 26 Page 2 of 28 Communication amp Control Software for DSO User Manual Chapter 1 Installation of the oscilloscope communication and control software 1 1 Hardware requirements Equipment requirements Minimal Oscilloscope Digital Storage Oscilloscope Computer Windows 2000 XP Vista 128 MB RAM 16X CD ROM or better Vista users please refer to its individual hardware requirements SVGA display or better Connection cable USB A B cable or RS232 cable or RJ45 net cable or GPIB communication cable 1 2 Installing the software Your Digital Storage Oscilloscope DSO comes with an oscilloscope communication and control software contained in the CD ROM supplied with your oscilloscope Alternatively you can download the software online File name oscilloscope communication and control software Installation Step one Insert the CD ROM supplied with your oscilloscope into the CD ROM drive of the computer Wait for the system to read and find the oscilloscope communication and control software contents Fig 1 1 i Communication amp s l Control Softwa oy J Setup Application Fig 1 1 Note 1 The installation pack downloaded online must be unzipped before application 2 The software supports Windows 2000 Windows XP and Vista operating systems On Vista only USB2 0 communication protocol is supported Step two Double left click the mouse to run the oscilloscope communication an
11. N EAEAER EFE ITIEAREENA NEEN TESE TENNEK CEARA TEENA OKEERE AKEU AAEN TEN E Virtual display panel HENU lt 4 gt E E ee Faria e Cursor Type Close VERTICAL HORIZONTAL TRIGGER co to 50 0 J E 2 a 7 c F5 a Operation mode a ll Serial Fig 2 11 Virtual control panel Function selection Saving and exiting screen Serial Single Close Save Select Single as in Fig 2 11 to save the waveform and screen on the virtual display panel in bmp format on the computer hard disk or mobile USB device Exit Quit the remote control transmission interface mode When serial is selected the waveform on the virtual display panel will be updated in real time and in synchronization with the waveform stored by the oscilloscope In this mode data volume is sizeable and control response is slower When single is selected the waveform on the waveform display screen is not displayed in synchronization with the waveform stored by the oscilloscope In this mode data volume is limited and control response is faster Close the transmission interface and return to the main control panel Fig 2 1 Page 19 of 28 Communication amp Control Software for DSO User Manual Chapter 3 Operation guide for the oscilloscope communication and control software By now you should have grasped the basic structure menu options and functions of the oscilloscope communication a
12. d control software installation as shown in Fig 1 1 The installation wizard for the oscilloscope communication and control software will pop up as shown in Fig 1 2 Page 3 of 28 Communication amp Control Software for DSO User Manual Digital Storage Oscilloscope Setup F ks Welcome Welcome to the installer for Cigi e Oscilloscope 1 01 tis strongly recommended that yo programs before continuing with Ifyou have any other programs nlease click Cancel clase the programs a is Setup again Otherwise click Next to continue Fig 1 2 Step three Read the prompt in Fig 1 2 then click the NEXT N button to enter the next step as shown in Fig 1 3 ro Digital Storage Oscilloscope Setup Mame User Company Microsoft es oe A oa Fig 1 3 Step four In Fig 1 3 enter your user name and company name then click the NEXT N button to enter the next step as shown in Fig 1 4 Page 4 of 28 Communication amp Control Software for DSO User Manual amp Digital Storage Oscilloscope Setup Space required 4 ME Space awai eon selected drive 14 74 GB Cancel Fig 1 4 Step five In Fig 1 4 click the CHANGE H button to specify the installation path of the software then click NEXT N You can also click NEXT N directly to use the default path Enter the screen shown in Fig 1 5 amp Digital Storage Oscilloscope Setup You are now ready to install
13. fferent hardware configurations Hardware Profiles Fig 4 4 Page 27 of 28 Communication amp Control Software for DSO User Manual Select equipment manager D in Fig 4 4 Fig 4 5 pops up Device Manager Sle File Action View Help nEs eA Display adapters 5 DYDICO ROM drives 4 Floppy disk controllers A Floppy disk drives 4 IDE ATAJATAPI controllers 2 Keyboards 1 Mice and other pointing devices gt Monitors Other devices Ports COM amp LPT ae Processors Sound video and game controllers z System devices Be Digital Storage Oscilloscope f Intel R S2801EB USB Universal Host Controller 2402 f Intel R S2801EB USB Universal Host Controller 24D4 f Intel R S2801EB USB Universal Host Controller 2407 f Intel R S2801EB USB Universal Host Controller 24DE f InteR 62601EB USB Enhanced Host Controller 24D0 ne USE Printing Support gt E E E E ee de ee eee ee ee ee 4 Fig 4 5 In Fig 4 5 delete digital storage oscilloscope in Universal serial main line controller to restart the oscilloscope Select automatic driver update to complete the update process Note When the communication and control software is communicating with the digital storage oscilloscope you cannot connect both the network cable and USB device cable to the oscilloscope ports and do not remove the cable to disconnect during communication Page 28 of 28 Communicatio
14. ication amp Control Software for DSO User Manual Enter the transmission interface and click the Transmission Interface button The indicator light comes ON Transmission interface mode is now enabled as shows in Fig 3 4 OB Far Control f x Function HENU RUNCONT Cursor Type Close VERTICAL HORIZONTAL TRIGGER VOLTS DIV SEC DIVU 50 0 y an L gt o e 1 a o ct Serial Single Fig 3 4 On the virtual control panel in Fig 3 4 you can operate your oscilloscope with different buttons as instructed by the oscilloscope user manual Select Serial on the above screen so the oscilloscope can transmit the oscilloscope screen to the virtual display panel in real time When Single is selected the virtual display panel will only show the first transmission interface Note In serial mode when transmission volume is high response of the software is relatively slow In single mode however response is quick as there is only one transmission and data volume is low When operation is complete press CLOSE to close this screen 99 66 Note The data transmission remote control and transmission interface functions cannot be operated simultaneously 3 2 Ethernet LAN interface controls The Ethernet port is a dedicated interface module of Digital Storage Oscilloscopes This TCP IP protocol embedded module can provide direct Ethernet connection to a oscilloscope
15. ital storage oscilloscope operation interface will pop up This is the virtual oscilloscope control panel When transmitting data you can observe the current waveform displayed by the oscilloscope on the virtual control panel This interface also features menus controls and knobs for accessing waveform and channel parameters please disable the data transmission function before using the menus to access information Please see below for detailed operation instructions Channel selection Transfer indicator TE Digital Oscilloscor Moneunicacsvus File Function Waveform Fresh Help myo o o CT eee CHANNEL STATUS A PNNEL OFFSET CH1 VERTICAL HORIZON Virtual display INTERVAL SANFLE Ch 1 stat Coupling BandLimit TYPE FILTER INVERSE annel status 7 oP Aee KENDON WaveForm InterFace C DC OFF l lel m j DEVICE Hi Shr ass Re Time me USB x _orF i BandPass OH p PROBE 1X EER Virtual control Coupling BandLimit TYPE FILTER INVERSE IHTERFOLATION panel OWL ass NO e ma omg mO mO H ae Hi ghPass ACTIUE 2 i BandPass om cae A oS 1X MATH Real time control Fig 2 1 Page 11 of 28 Communication amp Control Software for DSO User Manual 2 2 Main menu Fig 2 1 shows four menus under the main menu on the top left corner document function waveform refresh and help Their operation instructio
16. le to update the software driver take the following steps Right click the box on your computer desk top as shown in Fig 4 1 to activate the right click menu in Fig 4 2 Open Explore Search Manage Map Network Drive Disconnect Network Drive Create Shortcut Delete Pr Rename he omputer Properties Fig 4 1 Fig 4 2 Page 26 of 28 Communication amp Control Software for DSO User Manual In Fig 4 2 select attribute and right click to pop up Fig 4 3 System Properties System Restore General Computer Name Remote Advanced Automatic u pdates Hardware System Microsoft Windows F Professional Version 2002 Service Pack 2 Registered to KFE T6487 640 0059266 23985 Computer IntellA Pentium A 4 CPU 2 80GH2 2rd GHz S12 ME of RAM Fig 4 3 Select hardware in Fig 4 3 Fig 4 4 is displayed System Properties System Restore General Device Manager Computer Hame Remote Advanced Automatic Updates Hardware b The Device Manager lists all the hardware devices installed on pour computer Use the Device Manager to change the properties of any device Drivers Device Manager Driver Signing lets pou make sure that installed divers are compatible with Windows Windows Update lets you set up how Windows connects to Windows Update for drivers Hardware Profiles Se Hardware profiles provide a way for you to set up and store ga di
17. light comes on the function is ON when the indicator light goes off the function is OFF Data transmission when the indicator light comes on the function is ON when the indicator light goes off the function is OFF Transmission interface when the indicator light comes on the function is ON when the indicator light goes off the function is OFF Page 18 of 28 Communication amp Control Software for DSO User Manual Reverse mathematics function Indicator on means reverse mathematics function is in process Indicator off means reverse mathematics function is not in process Mathematics function Select mathematics functions with the function menu in the menu bar Auto Refresh Set up the refresh time interval with the waveform refresh menu in the menu bar Refresh time Set up refresh time while performing auto refresh 2 4 Transmission interface and explanatory notes To select USB or LAN to control communication click the transmission interface button on the virtual control panel of the communication and control software to enter the transmission interface operation screen Here you can enable remote interface transmission as shown in Fig 2 11 The virtual display panel shows the waveform and interface of the oscilloscope The virtual control panel is a virtual operation panel of your digital storage oscilloscope You can control and operate the unit from here TE Far Control Function Menu TENTA
18. n amp Control Software for DSO User Manual
19. n the name field then click to save Current data in the table can be saved locally as an EXCEL file To quit the data table test click exit TalbeFile Storage rite C Program Files Digital Storage Oscilloscope het Select the path Save in O Digital Storage Oscilloscope v fe fg EJ 2 B Uninstall My Recent Documents Desktop My Documents the document Enter Computer S My Network File name xls hi Places Save as type Cancel Fig 2 9 Parameter measurement This shows all the parameter values of the waveform currently on display in the selected channel Select channel You can select CH1 or CH2 Start pause transmission Start transmission means beginning to transmit data Pause transmission means stopping transmission TE Parameter Measurement Function Fig 2 10 Page 17 of 28 Communication amp Control Software for DSO User Manual 2 3 Waveform refresh Single refresh This is a single waveform trigger The acquired waveform display is stored on the display panel of the virtual control panel Waveform time interval setup To set up the time interval for waveform refresh Help This menu shows the version of the oscilloscope communication and control software Control panel instructions Keys on the control panel of the oscilloscope communication and control software Fig 2 1 function as follows Cha
20. nd control software In the following pages you will find more detailed instructions on how to operate the software In this chapter we will give guidance on USB LAN GPIB and RS 232 control modes To enjoy optimal software performance we recommend you to read the oscilloscope user manual and this chapter to familiar with application After installing the software and driver properly connect the cable to the USB A B communication port Power on the oscilloscope and activate the software The software control panel shown in Fig 3 1 will appear on your computer screen TE Digital Oscilloscope Communications Software Oj x File Function Waveform Fresh Help CH1 VERTICAL HORIZON MATH HATH SCALE OFF VOLTAGE TIME Auto_Fresh nm oO INTERVAL 0 03 E 100mv div EWM CHANNEL STATUS RealTime Control Coupling BandLimit TYPE FILTER INVERSE 3 Loit azs Kanaa InterFace C Dc OEE m DEVICE KG ee RealTime USB f on _orF l pandr ass ox PROBE 1X 1 BAUS BandStop SCAN USB2 0 Coupling BandLimit TYPE FILTER INVERSE INTERPOLATION d DC Lowbass No Hi ghP ass imal a ACTIVE INVERT an sza PROBE 1X CH zj 2 GD 0N Fig 3 1 Page 20 of 28 Communication amp Control Software for DSO User Manual 3 1 USB interface controls After installing your communication and control software please install the driver
21. nnel status This indicated the current control status of the digital storage oscilloscope During data transmission this status bar indicates the current control status of the oscilloscope This bar changes with the actual control status of the oscilloscope but you cannot control the current status of the oscilloscope with this bar CH1 Coupling method DC AC GND Bandwidth suppression On Off Filter type low pass high pass band pass band stop Digital filter when the indicator light comes on the function is ON when the indicator light goes off the function is OFF Reverse when the indicator comes on the function is ON when the indicator light goes off the function is OFF Probe 1X 10X 100X 1000X CH2 Coupling method DC AC GND Bandwidth suppression On Off Filter type low pass high pass band pass band stop Digital filter when the indicator light comes on the function is ON when the indicator light goes off the function is OFF Reverse when the indicator light comes on the function is ON when the indicator light goes off the function is OFF Probe 1X 10X 100X 1000X Sampling method Random Real time SCAN Interpolation Yes No Current activated channel MATH CH1 CH2 Channel selection CH1 CH2 MATH Bias adjustment Vertical Horizontal Range adjustment Voltage range Time base range Real time Control Equipment selection USB RS 232 LAN GPIB ON OFF when the indicator
22. ns are as follows 1 Document Load Note Save Record This means saving the oscilloscope communication and control software to the computer hard disk or other storage media or save it in a waveform file on any mobile storage media by using the long save function of the oscilloscope save menu and then open the saved waveform on the virtual display panel with the Load feature When storing a waveform from the digital storage oscilloscope to a mobile USB device storage mode of the oscilloscope must be set to long storage to load the waveform onto the computer software To set long storage use the STORAGE button on the front panel of the oscilloscope STORAGE Type WAVEFORM NEXT Disk USB Storage depth Long storage This means saving the waveform currently on the virtual display panel to a computer or other storage equipment Select Document Save and save it on the hard disk or mobile external hard disk in dat format Assign any file name you like Enable the data transmission function and select Document Record A prompt box shown in Fig 2 2 will pop up on the virtual display panel and recording of the virtual display waveform begins The recording prompt box shows the current waveform recording progress To pause recording simply click the pause button To resume click the continue button and recording will resume from the point where i
23. oscope communication and control software is complete you can run it on your computer in two ways 1 When installation of the oscilloscope communication and control software is complete an short cut icon is automatically created on the computer desktop as shown in Fig 1 8 To run the software simply double left click the icon in Fig 1 8 with your mouse 2 Alternatively you can run the software by going through START Programme Digital storage Fig 1 8 oscilloscope DSO as shown in Fig 1 9 L Q g i wv O i a am Fas un 1 ae acre Accessories rs Set Program Access and Defaults windows Catalog windows Update fag Digital Storage Oscilloscope _ p50 Documents P Uninstal Cinik Location C Program Startup WinRAR Search F Internet Explorer we MSN Help and Support Outlook Express Remote Assistance Settings RUN F windows Media Player a Windows Messenger Log OFF KFE i i Windows Movie Maker Turn OFF Computer Start Removable Disk 1 Fig 1 9 Page 7 of 28 Communication amp Control Software for DSO User Manual 1 4 Installing the USB driver If you are using the oscilloscope s USB device port for software communication and control the USB driver must be installed after installation of the oscilloscope communication and control software is complete Follow the steps below l There is a USB device port on the rea
24. r USB interface controls in this chapter Note When using the LAN interface you can operate the oscilloscope by remote control via LAN or the Internet Mapping feature of the router must be enabled and the public network address of your company should provided 3 3 GPIB interface controls The GPIB port is a dedicated interface module of Digital Storage Oscilloscopes After installing the communication and control software you can carry out system operation and control your oscilloscope through the GPIB interface You can create an automatic testing system simply quickly and efficiently and carry out testing and measuring With the optional UT M02 extension module you can operate your oscilloscope through the GPIB interface as follows 1 Select GPIB in the equipment selection option on the real time control panel 2 When GPIB is selected the dialog box in Fig 3 6 will pop up Page 23 of 28 Communication amp Control Software for DSO User Manual _ GPIB Setup x GPIB Card Type Sit PCI GPIB GPIB Card s Device Number ajo DSO s GPIB Address 0 Fig 3 6 Enter the GPIB device address in this box range 1 30 The GPIB device addresses set in the software and the communicated oscilloscope must be the same otherwise communication between the oscilloscope and the software cannot be established Access sub menu page 3 by pressing UTILITY GPIB on the oscilloscope control panel for GPIB device
25. r data transmission is completed or the waveform on the computer hard disk or mobile USB device which is downloaded to the software with the load function Depending on the number of channels working at the time of data transmission you can select the channel mode on the waveform preview interface with the selection function of the menu When uploading with two channels you can select single channel CH1 CH2 two channels CH1 amp CH2 CH1 amp Math CH2 amp Math or all to preview the waveform To quit the preview screen click the exit button The preview interface is the last screen uploaded by the oscilloscope to the computer after the transmission interface is closed When data transmission is complete select Document Print to print the waveform or the interface The printed waveform is the last screen of waveform data uploaded from the oscilloscope to the communication and control software after data transmission is completed or the waveform on the computer hard disk or mobile USB device which is downloaded to the software with the load function The print interface is the last screen uploaded by the oscilloscope to the computer after the transmission interface is closed After the data transmission or transmission interface task is complete select Document gt exit to quit the oscilloscope communication and control software
26. r panel of your Digital Storage Oscilloscope With the supplied USB A B cable you can connect the USB device port to the USB Host port of the computer and obtain power supply for the oscilloscope After checking that connection and power supply are normal power on the digital storage oscilloscope When the operation status screen appears a prompt will appear at the right bottom corner to indicate New hardware DSO detected as shown in Fig 1 10 i Found New Hardware bs Fig 1 10 Next an icon will be created for the New hardware DSO detected as shown in Fig 1 11 i Found New Hardware Digital Storage Oscilloscope Fig 1 11 Then a hardware update wizard dialog box will pop up on the desktop as shown in Fig 1 12 Found New Hardware Wizard This wizard helps you install software for Digital Storage Oscilloscope If your hardware came with an installation CD E or floppy disk insert it now What do you want the wizard to do Install the software automatically Recommended Install from a list or specific location Advanced Click Next to continue Fig 1 12 Page 8 of 28 Communication amp Control Software for DSO User Manual 3 In the new hardware wizard dialog box in Fig 1 12 select the automatic software installation recommended I option then click NEXT N to enter the automatic driver search and installation page as shown in Fig 1 13
27. search area to locate the storage path of the recorded waveform select the recorded waveform document you require then click the Load button Fig 2 5 will now appear By using the manual playback button you can play back the recorded waveform screen by screen Alternatively enter the required screen number in the screen number display field and press ENTER Your specified screen will be displayed To close the static playback function click the close static playback button Transcribed Data Storage Directory IEAProgram Files Digital Storage Osciloscope SS History C Program Files Digital Storage Oscilloscope Save in 4 Digital Storage Oscilloscope Uninstall My Recent Documents B Desktop My Documents y Mu Computer z Mu Network File name F dat Places Save as type Cancel Manual playback button Field for entering the number of screens Page 13 of 28 Communication amp Control Software for DSO User Manual Print preview Waveform Interface Printing Waveform Interface Exit 2 Functions After completing the data transmission or transmission interface task select Document print preview to preview the waveform or interface as the case may be before printing The preview waveform is the last screen of waveform data uploaded from the oscilloscope to the communication and control software afte
28. t was paused The dialog box in Fig 2 3 appears when you close the waveform recording function or recording has reached the maximum number of data screens Click YES in Fig 2 3 to save it in dat format on the computer hard disk or other storage device If you wish to abandon recording press NO as shown in Fig 2 3 The waveform recording function can record up to 2000 screens of data 8 System Message Do you want to sawe the waveform you transcribed Record qo Peuse Continue Close Fig 2 2 Fig 2 3 Page 12 of 28 Communication amp Control Software for DSO User Manual Playback After stopping data transmission you can play back the waveform recorded and saved on the computer hard disk or other mobile storage media Simply select Document Playback You can play back a waveform in dynamic or static mode Dynamic playback Static playback Select Document Playback Dynamic playback The waveform playback loading interface in Fig 2 4 will pop up Specify the search area to locate the storage path of the recorded waveform select the recorded waveform document you require then click the Load button The recorded waveform will be played continuously on the virtual display with the current playback progress Select Document Playback Static playback The waveform playback loading interface in Fig 2 4 will pop up Specify the
Download Pdf Manuals
Related Search