QK-BIOTX
Contents
1. quikoitaly com INCORRECT D Do not bend finger during swipe as this will only scan the tip of your finger E Swipe finger straight down not at an angle F Swipe flat not tilted or rolled to one side How to avoid damaging the biometric reader Keep always the protective cover closed when the transmitter is not used Avoid scratching the surface when it is used To avoid a major consumption of the biometric reader keep always the protective cover closed when it is not used QUIKO ITALY declares herewith that the product OK BIOTX complies with the requirements of the 1999 5 CEE R amp TTE Directive insofar as the product is used correctly CE DECLARATION OF CONFORMITY CE QUIKO ITALY Via Seccalegno 19 36040 Sossano Vi Italy Tel 39 0444 785513 Fax 39 0444 782371 info quiko biz www quikoitaly com qui IG 10 www quikoitaly com2. blue led will turn on for 2 seconds and a confirmation beep sound will be heard The channel programmed will be sent by default for the fingerprint used qui P D 6 www quikoitaly com e e0 Fraga MASTER FINGERPRINT NOT MASTER FINGERPRINT CONFIGURATION For NOT MASTER FINGERPRINT programming the device needs to be configured as follows 1 Enter configuration mode 2 Pressthe pushbuttons 2 and 4 for 2 seconds The blue and orange led will turn on 3 Pressthe pushbutton 4 The orange led turns on and 2 beeps are heard At this moment it is possible to program NOT MASTER FINGERPRINT following fingerprint programming chapter To reprogram MASTER FINGERPRINT again it will be necessary to reconfigure the device as follows 1 Enter configuration mode 2 Pressthe pushbuttons 2 and 4 for 2 seconds The blue and orange led will turn on 3 Pressthe pushbutton 4 The orange led flashes and 1 beep is heard 1 Ni i A NOT MASTER FINGERPRINT B MASTER FINGERPRINT Once the device is configured for the desired fingerprint programming follow the chapter FINGERPRINT PROGRAMMING oe qui 16d YY d www quikoitaly com LED Blue Biametric reader waiting a finger pnnt Confirmation fingerprint reading ok Biometic reader waiting for a finger print in pushbutton mode Device in configuration mode waiting for an action Devi gine for afi ini Confirmatio
3. EP QU 4 2 _5 times N PROGRAMATION OK rJ e 3 www quikoitaly com TERMINOLOGY Default channel the channel that will be send in biometric activation operating Master fingerprint fingerprint that allows using operating and configuration modes Not master fingerprint fingerprint that only allows using the operating mode CONFIGURATION MODE To enter configuration mode do the following 1 Openthe protective cover 2 Press the pushbuttons 1 and 4 at the same time until the three led turn on flashing Note if a stored fingerprint exists the white led will turn on Then you must pass one of the fingerprints already stored The blue led will turn on for 2 seconds and you will hear a beep The three led will flash indicating that the device is in configuration mode FINGERPRINT PROGRAMMING Enter configuration mode Press the button of the channel that you want to program the fingerprint for 2 seconds The white and orange led tum on for 5 seconds At the end of this selection the white led will remain at ON M1 1 2 3 4 Cela www quikoitaly com Pass the fingerprint to programme 5 times Each time that you swipe the finger the white and blue led make a flashing and a signal sound will be heard At the end of the fifth pass the blue led lights for 2 seconds fixed indicating the correct programming PROGRAMATION OK The equipment will remain in configuratio
4. QK BIOTX BIOMETRIC TRANSMITTER FOR OPERATING WITH QK AMBRX RECEIVERS 1 Led azul Led bleue Blue led Blaue Led 2 Led blanco Led blanche White led Weile Led 4 Led naranja Led orange Orange led Orangene Led a Pulsadores Boutons Pushbuttons Druckknopte 5 Lector biom trico Lecteur biom trique Fingerprint reader Biometrische Lesevorrichtung Tapa protectora Cache de protection Protective cover fingerprint reader Schutzabdeckung TECHNICAL DATA 20 Cto 85 C Operating temperature 20 C to 85 C IP55 Dimensions Battery duration approx qui lo 93X93x30mm 1 5 years with lithium battery www quikoitaly com INSTALLATION Within the packaging of this product you will find the equipment mounted 2 lithium batteries type AAA a TORX wrench and the user manual Unscrew the bottom screw with the wrench Unscrew the 4 front screws and remove provided and remove the front cover the inner piece Turn the piece and put the batteries in the back 4 Fix the base piece to the wall or recessed it as appropriate Follow all the instructions for the starting up the equipment 6 Fix the inner piece to the base with 4 screws and set the front to the base with the lower screw qui 0 2 www quikoitaly com STARTING UP OPEN THE PROTECTIVE COVER ENTER IN CONFIGURATION MODE BY PRESSING 1 AND 4 UNTIL YOU HEAR A CONFIRMATION BE
5. n fingerprint reading ok in configuration made e9 Device waiting for authorised channels or fingerprints Erasing one fingerprint Device in MASTER and NOT MASTER configuration mode Q NOT MASTER FINGERPRINT Configuration E C ashing 8 www quikoitaly com LOW BATTERY INDICATOR When the protective cover is opened the white and orange leds will be at ON and four beeps will be heard BIOMETRIC READER DAMAGED When the protective cover is opened the orange led will be at ON and one beep will be heard REPLACING THE BATTERY Follow the steps in INSTALLATION to open the equipment Remove the batteries and change them for the new ones Always use batteries of the same technical data that those supplied by the manufacturer to guarantee its durability RECOMMENDATIONS How to pass the fingerprint correctly over the reader CORRECT 1 Make sure finger is clean and dry Place finger flat above the sensor strip with the top knuckle above the sensor 2 Swipe finger straight down keeping firm contact with the sensor The swipe should be a slow constant speed Special notes Use the same finger for every swipe It is important to swipe finger slowly and firmly as this is the reason most swipes fall A Start swipe with the top knuckle above the sensor strip B Swipe finger straight down keeping firm contact with the sensor C The scan should end at the tip of finger qui 10 9 www
6. n mode This process must be repeated for all the desired fingerprints to program The first channel selected will be used by default channel Note If a fingerprint reading is not ok the orange led will flash and two beeps will be heard ERASING THE MEMORY Enter configuration mode A ERASING ONE FINGERPRINT 1 Press the pushbuttons 3 and 4 at the same time The white led flashes and 5 signal sounds will be heard Then the white led remains fixed 2 Pass the fingerprint to be erased The blue led will turn on and you will hear a confirmation signal sound Fingerprint to erase B TOTAL RESET Press the pushbuttons 1 and 3 at the same time for 10 seconds The orange led will flash and 10 long signal sounds will be heard Keep pressed the two pushbuttons and a serial of fast beeps will be heard indicating that the memory has been totally erased qui J D 5 www quikoitaly com e ec eb sore Keep pressed the two pushbuttons and a serial of fast will be heared indicating that the memory has been totally erased ERASING The equipment remains in configuration mode To exit configuration mode wait 10 seconds without doing any action or close the protective cover the device will exit from configuration mode and the three leds will swith off Two beeps will be heard OPERATION 1 Openthe protective cover the white led will turn on waiting for a fingerprint reading 2 Swipe your finger over the reader The
Download Pdf Manuals
Related Search
QK BIOTX qc biotech job